DIY toy printing press. Mk. DIY money printing machine. How much does a money printing machine cost?

Is it difficult to make a money printing machine yourself? I think that if only as a joke as a gift. But you shouldn’t mess with a real machine (it’s still criminally punishable), we’d rather earn money ourselves!

I saw a wonderful idea for a comic gift on the HOBBIN HOUSE website. Below is a video of the finished machine in operation and describes detailed master class on how to make this machine:

I want to show you how to make a money machine with your own hands. It has nothing in common with real printing presses, but as a cool gift for your friends on April 1 or a wedding, it will be great. This invention is of course not mine, I just want to show how I made this machine. Such a machine for money can now be bought at any joke store or on the Internet for 500 rubles. But in my case, the store ran out of them, and I didn’t have time to order online, so I had to do it myself in order to have time to give it to friends as an anniversary gift.

To make a money machine, we need:

Wooden boards, hot melt glue, thick and thin wire, cardboard tubes, self-tapping screws and film for gift wrapping.

We start by sawing off two pieces 15 cm long and one 20 cm long from a wooden board. Sand the edges of the cut well so that they are smooth.

From a cardboard tube (in stores they have oilcloth wrapped around them, which is sold by the meter), we cut off two pieces about 14 cm long. Then, we mark circles on thick cardboard.

We cut out these circles and glue them with hot glue, two pieces at a time.

Now we glue these circles into cardboard tubes. On each side of the tube we mark a hole in the center. We mark and drill holes for the handles on the boards. On the top board, the right hole must be drilled through. And the left hole must be drilled to the middle of the board, so that there is no hole on the other side of the board. On the bottom board, do the opposite. We drill the right hole to the middle of the board, and drill the left hole all the way through.

We make two handles from thick wire, one with a long handle and the other with a short handle. We insert the handle into the hole in the board and put our cardboard blank on it. We secure it with a thin wire and glue the ends of the wire to the cardboard, this is necessary so that the drum rotates with the handle and holds on to it well..

This is what we should end up with, one drum is mounted on a board and a handle with a short handle, and the second is on a board and a handle with a long handle. On a board 20cm long, we mark the places where we will screw the boards with the drums.

We assemble our machine, fix everything with self-tapping screws. This is how it should work out. We cover everything with stain.

We glue a piece of suede to the base to cover the attachment points. Glue decorative tape along the edges.

Now all we have to do is insert the ribbon into our money machine. We take a beautiful film for wrapping gifts and cut it into a 14 cm wide ribbon. The length of your ribbon will determine how many bills you can put into the machine.

We insert the end of the tape between the drums and pull it under the lower drum.

Apply glue to the bottom drum and glue the end of the tape to the drum. Since the tape is wound on the drums with different sides facing outwards. The sides of the tape have different colour, which enhances the illusion of independence of the rollers.

We wind the entire tape onto the lower drum, and glue the remaining free end of the tape to the upper drum. The result should be: the top drum is golden, the bottom drum is silver. The tape is inserted according to the figure eight principle.

We print out the stickers we need, put them on the bottom drum at the very end of the tape, and glue the “FINISH” sticker onto the tape.

On the top drum, at the very beginning of the tape, glue the “START” sticker. We glue the “MONEY” sticker on the side above the handle with a long handle.

On the other hand, above the handle with a short handle we glue the “SETUP” sticker. At the bottom, on the side from where the money will come out, we glue the “MONEY” sticker. And on the side from which we will feed the paper, glue the “PAPER” sticker. The machine is ready, all that remains is to refuel it.

We rewind the entire tape onto the upper drum, up to the “FINISH” sticker. We take a bill, insert it between the reels and start turning the small “SETUP” knob. Thus, the bill is twisted between the ribbon and onto the lower drum. So, we fill all the bills up to the “START” sticker. After all the bills are inserted into the money machine. We take the paper, insert it on the other side between the rollers, and turn the handle with a long handle. So the paper begins to curl, between the ribbon on the upper drum and on the other side, the bill we have already inserted comes out.

That's it, our money machine is ready and loaded. As you can see, everything is very simple. “Print money” with this cool gift “ money machine"Anyone can do it. Be careful: some people believe this illusion very strongly. “Money machine” is an excellent gift for the first of April, for the New Year, for a wedding, etc. And also, a wonderful replacement for the faceless envelopes in which it is customary to make cash gifts.

on 2014-01-16

Is it difficult to make a money printing machine yourself? I believe that if only a joke as a gift. But we shouldn’t mess with a real machine (it’s still criminally punishable), it’s better that we get the money ourselves!

I noticed an excellent joke gift idea on the HOBBIN HOUSE website. Below is a video of the finished machine in operation and a detailed master class on how to make this machine:

I would like to demonstrate to you how to make a money machine with my own hands. It has nothing unspecialized with real printing presses, but as a cool gift for your friends on April 1 or a wedding, it will be perfect. This invention, of course, is not mine, I only want to demonstrate how I made this machine.

Such a machine for money, on this moment Can be purchased at any joke store or online for 500 rubles. But in my case, the store ran out of them, and there was no time to order online, so I had to do it myself in order to have time to give it to my friends for their anniversary.

To make a money machine, we need:

Wood planks, hot glue, thick and narrow wire, cardboard tubes, self-tapping screws and film for gift wrapping.

We start by sawing off two pieces of wood 15 cm long and one 20 cm long. We sand the edges of the cut perfectly. so that they are even.

From a cardboard tube (in stores they have oilcloth wrapped around them, which is sold by the meter), we saw off two pieces approximately 14 cm long. After that. Mark circles on thick cardboard.

We cut out these circles and glue them with hot glue, two pieces at a time.

Now we glue these circles into cardboard tubes. On each side of the tube we mark a hole in the center. We mark and drill holes for the handles on the boards.

On the top board, the right hole must be drilled completely. And the left hole needs to be drilled to the middle of the board, so that otherwise there will be no hole in the board. On the bottom board, do the opposite.

We drill the right hole to the middle of the board, and drill the left hole completely.

We make two handles from thick wire, one with a long handle and the other with a small one. We insert the handle into the hole in the board and put a domestic cardboard blank on it. We secure it with a narrow wire and glue the ends of the wire to the cardboard, this is necessary. the drum spun along with the handle and held on to it perfectly..

This is what we should end up with, one drum is put on a board and a handle with a small handle, and the second is on a board and a handle with

long handle. On a board 20cm long, we mark the places where we will screw the boards with the drums.

We assemble a domestic machine and fix everything with self-tapping screws. That's what it should be like without that. We cover everything with stain.

We glue a piece of suede to the base to cover the attachment points. Glue decorative tape along the edges.

Now all we have to do is insert the ribbon into the domestic money machine. We take an excellent film for gift wrapping and cut it into a 14 cm wide ribbon. The length of your ribbon will determine how many bills you can put into the machine.

We insert the finish of the tape between the drums and pull it under the bottom drum.

Apply glue to the bottom drum and glue the finish of the tape to the drum. Since the tape is wound on drums with different sides facing outwards. The sides of the tape have different colors, which enhances the illusion of independence of the rollers.

We wind the entire tape onto the lower drum, and glue the remaining free end of the tape to the upper drum. In the end it should be. The top drum is gold. The bottom drum is silver. The tape is inserted according to the figure eight principle.

We print out the stickers we need, put the FINISH sticker on the bottom drum at the very end of the tape, and stick it on the tape.

On the top drum, at the very beginning of the tape, glue the START sticker. Place a MONEY sticker on the side above the handle with a long handle.

Otherwise, above the handle with a small handle we glue the SETUP sticker. At the bottom, on the side where the money will come out, we glue the MONEY sticker. And on the side from which we will feed the paper, glue the PAPER sticker.

The machine is ready, all that remains is to refuel it.

We rewind the entire tape onto the upper drum, up to the FINISH sticker. We take a bill, insert it between the reels and start turning the small SETUP knob. So, the bill is twisted between the ribbon, onto the lower drum. So, we fill all the bills up to the START sticker.

Once all the bills are inserted into the money machine. We take the paper, insert it differently between the rollers, and turn the handle with a long handle. So the paper begins to curl, between the ribbon on the upper drum, otherwise, the bill we have already inserted comes out.

That's it, the domestic money machine is ready and fueled. As you can see, everything is quite easy. “Print money” for a cool gift “ Financial machine"Anyone can do it. Be careful: some people strongly believe this illusion. “Financial machine” is a good gift for the first of April, for the New Year, for a wedding, etc.

And, an excellent replacement for the faceless envelopes in which financial gifts are usually made.

Source: www.liveinternet.ru

PRINTING PRESS FOR MONEY WITH YOUR HANDS

Fascinating posts:

A selection of articles that should interest you:

I would like to demonstrate to you how to make a money machine with your own hands. It has nothing in common with real printing presses, but how...

January 6, 2014 Money is the best gift. But it’s easy to present them to the hero of the occasion in an envelope - it’s boring and obvious. If you wish...

There are times when there is not enough money in life. Then it is possible to try to make talismans to attract money. There are many of them...

In the articles below, anyone can learn how to create bouquets of money with their own hands. It is possible to look at a few photos of what such bouquets look like...

Wedding paraphernalia, thanks to which the celebration of the reunion of two hearts is transformed into a celebration of pomp and romance, is distinguished by an enviable…

Aug 4, 2013. A printing machine with an easy secret for money, but a fascinating one. — In each board you need to make two holes, one through, Nov. 5.4…

I want to show you how to make a money machine with your own hands. It has nothing in common with real printing presses, but as a cool gift for your friends on April 1 or a wedding, it will be great. This invention, of course, is not mine. I just want to show how I made this machine. This is a money machine , Now you can buy it at any joke store or on the Internet for 500 rubles. But in my case, the store ran out of them, and I didn’t have time to order online, so I had to do it myself in order to have time to give it to friends as an anniversary gift.

To make a money machine, we will need:

Wooden boards, hot melt glue, thick and thin wire, cardboard tubes, self-tapping screws and film for gift wrapping.

We start by sawing off two pieces 15 cm long and one 20 cm long from a wooden board. Sand the edges of the cut well so that they are smooth.

From a cardboard tube (in stores they have oilcloth wrapped around them, which is sold by the meter), we cut off two pieces about 14 cm long. Then, we mark circles on thick cardboard.

We cut out these circles and glue them with hot glue, two pieces at a time.

We assemble our machine, fix everything with self-tapping screws. This is how it should work out. We cover everything with stain.

We glue a piece of suede to the base to cover the attachment points. Glue decorative tape along the edges.

We insert the end of the tape between the drums and pull it under the lower drum.

Apply glue to the bottom drum and glue the end of the tape to the drum. Since the tape is wound on the drums with different sides facing outwards. The sides of the tape have different colors, which enhances the illusion of independence of the rollers.

We print out the stickers we need, put them on the bottom drum at the very end of the tape, and glue the “FINISH” sticker onto the tape.

On the top drum, at the very beginning of the tape, glue the “START” sticker. We glue the “MONEY” sticker on the side above the handle with a long handle.

On the other hand, above the handle with a short handle we glue the “SETUP” sticker. At the bottom, on the side where the money will come out, we glue the “MONEY” sticker. And on the side from which we will feed the paper, we glue the “PAPER” sticker. The machine is ready, all that remains is to refuel it.

We rewind the entire tape onto the upper drum, up to the “FINISH” sticker. We take a bill, insert it between the reels and start turning the small “SETUP” knob. Thus, the bill is twisted between the ribbon and onto the lower drum. So, we fill all the bills up to the “START” sticker. After all the bills are tucked into the . We take the paper, insert it on the other side between the rollers, and turn the handle with a long handle. So the paper begins to curl, between the ribbon on the upper drum and on the other side, the bill we have already inserted comes out.

That's it, our money machine is ready and loaded. As you can see, everything is very simple. Anyone can “print money” with the help of such a cool “Money Machine” gift. Be careful: some people believe this illusion very strongly. “Money machine” is an excellent gift for the first of April, for the New Year, for a wedding, etc. And also, a wonderful replacement for the faceless envelopes in which it is customary to make cash gifts.

A money typewriter can be an original, and most importantly, “necessary” wedding gift. Such a thing will undoubtedly arouse interest both among the guests and the newlyweds themselves, and will become the most an original gift. Some, having believed in the miracle of creation, will even envy the newlyweds.

We gave such a typewriter as a wedding gift to my brother, and many asked how to make one. We’ll tell you how, since it’s more difficult to find it in stores than to make it yourself. Of course, this cannot be done without male help. Detailed photos Unfortunately no, I will try to explain clearly.

We will need:

- board 7-10 cm wide, ~15 cm long (base) - 1 pc.

- a block or board 3-4 cm wide, 7-8 cm long (supports) - 2 pcs.

- wire 35-40 cm.

- plastic pipe, any diameter, 8 cm long - 2 pcs.

- fabric or ribbon 7-8 cm wide. The length depends on the number of bills plus two diameters of the plastic pipe - 1 pc.

- glue or tape

— screws 16 mm.

- drill-driver

- a drill with a diameter slightly larger than the diameter of the wire

- pliers

- tassel

- stain.

1. Let's start by preparing future shafts. For this purpose in plastic pipes We insert wooden dowels at both ends. Next, use a drill to drill holes in them.

2. Prepare supports for the shafts. In each board you need to make two holes, one through, the other not, so that it is beautiful.

To do this, we place boards 4 cm wide on top of each other and drill holes. We drill the first hole on the first board through, the second not all the way through, then we turn the boards over and on the second board we drill the first hole not through, but the second through.

The distance between the holes depends on the diameter of the selected pipes and the thickness of the material in which you will wrap the money.

3. The next step is to install the shafts on the supports.

Let's make levers. To do this, bend one wire in the shape of the letter L (the length before the bend is equal to the distance between the supports plus the width of the support). We install the wire in the lower through hole, then thread it through the shaft, and insert it into another support in a non-through hole.

We first bend the second wire in the same way as the first, thread it in the same way as the first from the top through hole, then bend the free end of the wire so that it is convenient to turn the handle of the machine.

4. Cover the money printing machine with stain or varnish.

After gluing, we wind the tape onto the lower shaft along with the bills.

6. We glue stickers to our money typewriter, so that it is clear which way to turn, where to insert pieces of paper and where to expect money from.

All is ready! You can show and give your souvenir and surprise people.

If you have any questions, write comments and we will definitely answer. If you like the idea, click the button to tell your friends on social networks and you won’t lose it and your friends will be interested in reading it.

Here's a look at how such a machine works.

PRINTING PRESS FOR MONEY WITH YOUR HANDS

Fascinating posts:

A selection of articles that should interest you:

You may also like