home · Networks · 192.168 10.10 setting up a Rostelecom router setting a password. How to log into the Rostelecom router - enter the modem settings. How to open ports on a router

192.168 10.10 setting up a Rostelecom router setting a password. How to log into the Rostelecom router - enter the modem settings. How to open ports on a router

To change the password for authorization in the wifi network or view the already set password, you need to know how to enter the router settings. You can also configure the access point name, network parameters, connection status and other settings through the control panel.

Router TP-Link

All tp link routers have a similar configuration, so the instructions are suitable for all device models. Going into the configuration settings is quite simple.

Follow the instructions:

  • First you need to connect your computer to the router via Wi-Fi;
  • As soon as the connection is established, check if the Internet is working - this is an indicator that the router is working as usual;
  • Use any browser installed on your computer. In the address bar, enter the address 192.168.0.1 or 192.168.0.1. The address for accessing the router's system control panel is indicated on the bottom panel of the router. After entering the local address in the address bar, you must press the Enter key. The following window will appear:

Router management login window

  • In the window you must enter your username and password to log in. Typically these are admin and admin. If this combination does not work, check the bottom panel of the router or the user manual. Login information must be provided there;
  • After entering your username and password, the control panel will appear. It looks like this:

Control panel appearance

Router D-Link

D link routers are one of the most popular routers on the market today. Their special feature is their ease of setup. This makes them perfect for home use. The router can also support several communication methods at once. You can configure the device in two ways:

  • Using the disk that is included with the product;
  • By going to the configuration settings panel.

To enter the settings panel, launch any browser installed on your PC and follow the instructions below:

  • Enter IP168.0.1 in the address bar - d link routers connect only to this address;
  • Press Enter;
  • In the window that opens, enter your authorization information. By default, the password is 1234 and the login is admin. This data may change if you purchased the router directly from the provider;

  • The control panel looks like this:

Router settings panel

Router Asus

Asus routers are distinguished by high performance and affordable prices. Before setting up, it is better to connect these types of routers directly to the computer, rather than connect using a Wi-Fi connection.

The connection diagram is shown in the figure below:

Connection diagram for Asus router to computer

The WAN Internet cable is indicated in yellow; LAN is the port through which the connection to a personal computer is made. After the router is connected to the computer, you will need to set the PC to automatically obtain an address in the network settings. Go to the Network and Sharing Center, click on the router's network and open the Internet Protocol properties window. Set to receive IP automatically.

Setting up automatic IP acquisition

Now open the default browser you use on your computer. In the search bar, enter the address 192.168.1.1 and in the dialog box that opens, enter the name of the network administrator and the password to access it. For Asus devices this is admin and admin.

After completing these steps, the router configuration management window will open:

Asus router settings window

Remember! You must connect to the settings panel after connecting the router to your computer. Otherwise, when trying to access viawifi, you may receive a message that the browser was unable to connect to the remote server.

Zyxel Keenetic router

The peculiarity of the Zyxel Keenetic router series lies in their powerful technical characteristics. Thanks to them, the router has a wide range of operation. However, such routers are quite expensive. Their price varies from 1500 to 5000 rubles.

For the device to work correctly, you need to configure its operation using the router control panel.

Follow the instructions:

  1. First, make sure your router firmware is updated to the latest version. The currently installed version can be viewed on the bottom panel of the device. The new software will help the user avoid problems during setup and further operation of the device. You can download the current firmware version from the official website of the router manufacturer;
  2. In the address bar of the browser, enter the address 192.168.0.1 and press Enter;
  3. In the window, enter your username and password to log in as the router administrator and gain access to all information and settings. Password – 1234, login – admin. Remember that case matters.

Control panel for zyxel Keenetic router

Routers Rostelecom

Rostelecom has been providing its users with their own branded routers for several years now. As a rule, they are produced by well-known manufacturers on the market: D Link, QTech, Sagemcom or Huawei. More than 80% of routers for the Russian company are produced by the manufacturer Sagemcom. Let's take a closer look at how to enter the settings of such a router:

  1. Connect your computer to the router via Wi-Fi;
  2. In the browser, enter the router web interface address 192.168.1.1 and press Enter;
  3. In the pop-up window, enter the password - admin or login - admin. If these details do not suit, try logging in using your login superadmin and password Is$uper@dmin. This will log you into the control panel as a superuser.

Settings panel for Rostelecom routers

If you can't connect to the router's web address

If, after entering the IP address 192.168.1.1 or 192.168.0.1, the browser window shown in the figure appears, this indicates that additional configuration of the router is necessary.

Failed attempt to connect to the router's web address

There are two possible reasons for the connection error:

  • The router is not connected correctly to the computer (in the case when the connection is made not through Wi-Fi, but through the ports of the computer and the router);

The correct diagram for connecting the router to the computer is shown in the figure above. The connection to the computer or laptop itself will look like this:

Router connected to laptop using network cable

If everything is connected correctly, one of the indicators on the router will light up, which is responsible for the operation of the LAN port.

Operation of the indicator responsible for the LAN port

  • Another reason for an error connecting a web address is that the network settings on the computer are incorrect.

After the router is correctly connected to the computer, open the current connections window on the PC taskbar:

Current connections window in Windows OS

The computer must be connected to the router. If the connection status is set to “Without Internet access”, you need to make network settings.

To do this, follow the instructions:

  • Go to the Network and Sharing Center. To do this, right-click on the current connections icon and select the appropriate menu item, as shown in the figure below:

Opening the Connected Network Control Center on your PC

  • Go to the window for changing network adapter settings;
  • Select the local network connection icon and open its properties window;

Opening LAN properties

  • In the list, select the network connection protocol version 4 and select its properties;
  • In the window that opens, check the boxes next to the options for obtaining IP and DNS addresses, as shown in the figure;

Setting up the connection protocol

  • Save all changes and try logging into the router settings panel again (using a browser).

Determining the router's IP address

In ninety percent of cases, you can go to the router settings at 192.168.1.1 or 192.168.0.1. If you have made all the necessary settings and access to the Internet appears on your PC, but you cannot connect to the router’s settings panel, your router may be using a special web address. In this case, you need to look at the required IP in the connection settings on the user’s computer.

Go to the Network and Sharing Center. Now look for the LAN connection icon. Right-click on it and select “Status”. In the window that opens, click on the “Details” button. More information about your network connection appears. Find the “Default Gateway IP” field; its value is the address that needs to be entered into the address bar of the browser.

IP Gateway Check

Setting up a connection address manually

The network may not support the ability to automatically configure IP addresses. In this case, you need to configure the network parameters yourself. Go to the connection protocol settings window (Figure 17). Instead of automatic configuration, check the “Use the following IP address” and “Use the following DNS server” checkboxes.

For tp-link routers, enter the following parameters:

Manually setting connection parameters for a tp link router

Users of routers from the manufacturer D Link must enter the following parameters to organize the connection:

Organization of manual network configuration for D Link routers

Resetting authorization data

If you cannot remember a previously changed login and/or password at the authorization stage in the browser, the only way to solve the problem is to reset the router settings. All parameters will be returned to the original (factory) configuration and the access password will become standard. It is indicated in the user manual or on the bottom cover of the router.

The reset process is very simple. There is a reset button on the back of the router; you need to press it with any sharp object for 10-15 seconds. After clicking, all settings will be returned to factory settings, and you will be able to log into the router control panel using the standard login and password.

Button to return to standard router settings

Using all the methods described in this article, you can quickly log into the router’s control panel for further configuration.

Views: 4,087

Rostelecom routers are configured in the same way as most similar devices. The sequence of actions required for connection, authorization and changing parameters will be discussed in detail below.

Let's start with the basics. To enter the router settings, you need to connect it to the power supply and wait until the equipment boots up. The next important point is the connection method. You can access the router control panel in two ways - via cable or WI-FI. In both cases, the possibilities for changing the configuration are almost the same, with the exception that you cannot reflash the router via WI-FI.

In the case of a wireless connection, you first need to find a newly created WI-FI network, which by default has a name similar to the router model; entering a password will not be required if no one has assigned it before.

When pairing a PC and a router via cable, you must insert one of the connectors into the network card connector on the computer, and the other into the LAN port of the router.

Further actions are no different both in the case of configuration via wire and without it.

  • We launch the program to view Internet pages (to enter the settings of the Rostelecom router, any browser, for example, Opera, will do). It doesn’t matter if you log in from a smartphone or PC.
  • In the address bar, enter the IP of the router, for example, 192.168.1.1 or 192.168.0.1.
  • If the address is correct, an authorization form will appear in which we enter the username and password to log into the Rostelecom router (usually admin/admin).

In most cases, the above values ​​will be correct and once entered, the device control panel status page will open. If the parameters were changed for some reason, then when logging into the admin panel of the router, a number of problems may arise, the solution to which is described below.

How to find out the IP address of a router

One of the most common login errors is when the page not found message is displayed at the address specified in the browser line. A common reason for this message to appear is an incorrectly entered IP. The easiest way to recognize it is by examining the sticker on the bottom panel of the device; the password and login for logging into the router are also indicated there. If for some reason the sticker is missing or it is impossible to make out what is written on it, the address is written in the operating instructions, as well as in a copy of the Rostelecom agreement held by the subscriber.

There are situations when none of the above exists. In this case, you should contact the provider's technical support. Over the phone, a company employee will tell you the sequence of actions necessary to find out the address of the Rostelecom router, its login and password.

Common causes of control panel login errors and how to fix them

If you start the command line (key combination Win + R, in the field that opens, write cmd and press enter) and type ipconfig in it, among other things, there will be an item - the main gateway. The numerical value opposite it is the address of the router to which the PC is directly connected.

For Windows devices, a connection error may be displayed due to the lack of a network card driver. In this situation, the connection icon in the notification panel is crossed out with a red cross, and when you hover the mouse cursor over it, a message is displayed indicating that the network cable is not connected. The problem can be solved by installing the driver (if this is a temporary glitch, just restart the PC).

Internet Protocol version 4 settings should be set to automatically obtain the IP address and DNS server addresses. This parameter is checked in the Network Control Center -> change adapter parameters -> right-click on the cable connection -> properties -> right-click on the IPv4 protocol -> properties. In the window that opens, you need to set the switches to automatically obtain addresses.

Resetting the router to default settings

If you still cannot log into the Rostelecom router, you need to reset its configuration to its factory state. This procedure is quite simple, but the process may vary depending on the specific model. Most devices have a reset button - Reset, WPS/Reset or the like. All you need to do is press and hold the button for 10-15 seconds, after which the device will reboot with default settings.

On some modifications, this key is hidden and can only be pressed with a thin, sharp object. The principle is the same - hold it for 15 seconds and wait until it reboots. It is important that you do not turn off the power during the reset process.

After successfully installing the factory settings, the IP address of the Rostelecom router will correspond to that indicated on the label below or in the operating instructions. How to log into the router’s web interface was described above. Simply enter the address into your browser and then provide your authorization details.

Firmware for Rostelecom router to the latest version

The procedure should be performed only when pairing a PC and a Rostelecom router via cable. The sequence of actions is as follows:

  • Download the file with the latest firmware version from the manufacturer’s official website (on some models this is not necessary, the file will be downloaded and installed during the update through the admin panel interface).
  • Let's go to router management.
  • We are looking for the system tools tab or something similar.
  • Go to the software update subsection.
  • On the page that opens, you will be asked to specify the previously downloaded file, select it and click the “Update” button.

The system will install the downloaded file, reboot, after which the Rostelecom device will operate under the latest firmware version.

The router control panel is needed so that you can set up an Internet connection, change the name and password of the access point, check the functionality of the Internet, etc. Most routers are programmed with a single address 192.168.1.1 or 192.168.0.1. But it’s not always possible to simply enter this address in the browser and gain access to the router’s personal account. Sometimes problems arise that prevent this.

What to do to log into the control panel via http://192.168.1.1

The most important aspect is that your router must support an active Wi-Fi access point. The device should do this even if it does not connect to the Internet. If this does not happen, try disconnecting the router from the power supply and wait 20-30 seconds. and connect it to the network again.

Also, sometimes a complete reset of settings helps - there is a special button on the router for this, which is often labeled “reboot” or “reset”. Sometimes, instead of a convex button, there is a narrow hole where you need to insert a needle or match and hold the button for 30 seconds. until the settings are completely reset. In this case, the connection name (192.168.1.1) and password are returned to the factory values ​​(admin admin) - they must be indicated on the router case.

Once the Wi-Fi hotspot is detected by your computer, connect and go to your browser. In the address bar, enter . If nothing happens, try 192.168.0.1. On the page that opens, you need to specify the administrator login and password.

Please note that the authorization data of your access point is not relevant to the admin panel. If you did not change it yourself, then you can log into your personal account using the login and password “admin”. Sometimes the manufacturer sets other standard settings - look for information on the router box or in its documentation.

The router works, but does not log into your personal account 192.168.1.1

If you encounter this situation, make sure you are using the correct control panel address. On most routers this is http://192.168.1.1, but on some models (D-Link, Tenda, etc.) 192.168.0.1 is used. Try connecting your router using the built-in power cord slot. In this case, the computer must independently connect to the Internet, which is configured on the router.

If this does not help, check your IP and DNS settings in the Network and Sharing Center (in Windows 7 and 10). To do this, right-click on the Internet connection icon, click LMB (left mouse button) on the section with the corresponding name. The control panel will open, right-click (right mouse button) on the connection name opposite “access type” and in the context menu that opens, select “properties > IPv4”.

Here you need to check the boxes that cause automatic detection of DNS and IP addresses. Static data only needs to be specified if it is predefined by your Internet provider.

In this case, you need to indicate the identifiers and subscriber registration data that were issued to you during the execution of the contract. If you were not given them or you have lost the necessary information, call your provider’s technical support and find out the IP/DNS.

In addition to providing Internet access and broadcasting digital television, Rostelecom provides its subscribers with branded universal equipment on a rental basis. Naturally, the communication service provider does not manufacture routers, modems and subscriber terminals. This is done by Chinese manufacturers such as TP-Link, Sagemcom, ZTE, Huawei and some others.

Setting up a Rostelecom router yourself is not difficult. The device comes with a disk containing a special utility for configuring the connection automatically. Users who do not accept automation can use the standard method and configure the equipment via the web interface.

Useful video on step-by-step setup of ADSL routers from Rostelecom:

Rostelecom router parameters for accessing the Internet and watching television

In addition to Internet access, the provider provides its subscribers with the opportunity to watch digital interactive TV channels. To take advantage of this offer, you need to fill out the appropriate application at the company’s office or on the official website.

Many modern TVs allow you to view interactive TV channels without additional equipment. Everyone else will have to get a special attachment. Depending on the equipment model and user preferences, the connection can be organized using a cable or Wi-Fi.

For a wired connection, the set-top box is equipped with a special cable, one end of which must be inserted into the TV and the other into the yellow port of the router.

To connect the set-top box to the TV, it comes with a composite cable (RCA jack), which is also called a “tulip”. If you connect the set-top box to a TV using it, you will be able to watch videos in DVD quality. To watch HD-Video you will need an HDMI cable, which will have to be purchased separately. In addition, for a full viewing experience, the TV must support the HD format.

The devices that Rostelecom provides to its users usually do not require configuration. The connection occurs automatically and there is no need to enter any data. But there are times when the configuration parameters are lost. In such a situation, you will need to reconfigure the connection configuration.

First you need to get into the control panel of the router. To do this, enter http://192.168.1.1 in the address bar of the browser, and in the user authorization data fields we indicate the standard pair: login “admin” and default password “admin”.

In the TP-link control panel, in the menu on the left, select “Network” -> IPTV. On the page that opens, specify the connection type as “Bridge” and select Lan4 as the port. After that, click the “Save” button. A reboot is not required for the settings to take effect.

All that remains to be done is to set up the TV using the remote control. After selecting the display mode (HDMI, AV), downloading digital television will begin. Upon completion, a window for entering user registration data will open. The subscriber's login and password, required to confirm login, are provided by the provider and must be specified in the relevant agreement.

After successful login, a menu and a list of TV channels will open.

How to enter the settings of the Rostelecom router

To access the web interface of the Rostelecom access point control panel, you will need the IP address of the device and authorization data (login/password). These are all usually listed on the device or provided by your carrier. The most common addresses are 192.168.1.1 and 192.168.0.1. The login and password are usually “admin”. If the data does not match, check the sticker on the bottom of the router or ask your provider.

Video instructions to log into the router using a local IP address:

For D-Link devices with new firmware, the authorization page looks like this:

We get to the advanced settings page, where we follow the “WAN” link in the “Network” block:

After this, a tab with a list of connections will open, on which there should be only one connection. If you click on it, a menu of options will appear in which you need to select “Delete”. After the page reloads, you need to create a new connection; to do this, click “Add” (item below). The connection options configuration tab should open. We indicate on it:

  • connection type – PPPOE;
  • connection name – any, for example, “Rostelecom”;
  • login/password (provided by the provider);
  • It's better not to touch the rest. Click “Save”.

Setting up a Wi-Fi connection on a Rostelecom router

First you need to log into the admin panel of the device. The procedure is described above. Then go to “Advanced” -> Wi-Fi tab -> “Basic”. On this tab we fill in all the necessary options:

  • SSID – network name (at your discretion, in Latin);
  • Channel – it is better to leave “auto”;
  • Mode - if there are no old devices, you can select 802.11N, otherwise we leave it as is.
  • The maximum number of clients is 0 (unlimited).

When finished, click “Edit” in the lower right corner

Then we configure the Wi-Fi network protection settings. Go to the “Security Settings” menu, set network authentication – WPA2/PSK and AES encryption. In the encryption key field, enter the Wi-Fi access password.

Now you can use the network by connecting with the specified password.

Setting up the router automatically

Rostelecom, for the convenience of subscribers, includes a disk with all branded access points. It contains an application for automatically configuring equipment.

Using this utility, you can set all the necessary options without entering the web interface. All you need to do is insert the disc into your computer and run the installation program.

How to set up a computer to work with a Rostelecom router

Difficulties with setting up Rostelecom routers may arise due to incorrectly configured network parameters in Windows. For everything to work correctly, the network card drivers must be installed (usually on the disk for the motherboard or network card). In addition, you need to check the TCP/IPv4 protocol parameters.

Go to “Control Panel” -> “Network and Internet” -> “Network Connections”, select your connection (usually its name contains the name of the network adapter), right-click on it, select properties:

In the window that opens, click once on “Internet Protocol TCP/IPv4”, it should be highlighted in a dark color, after which the “Properties” button will become active. Click on it.

The Internet Protocol v4 settings window will open. In it you need to enable the radio button “Obtain an IP address automatically” and “Obtain DNS server address automatically”. Confirm by clicking “Ok”.

If the configuration parameters of the Rostelecom access point are lost

Viruses, system failures, and carelessness of users can cause software problems in the operation of the router. To restore the functionality of the equipment, it is possible to reset to factory settings. Reset methods may differ for each model. On some, you just need to press and hold the “WPS/Reset” button for 10-20 seconds.

On others, the buttons are located in a hard-to-reach place so that the user does not accidentally reset the configuration. To press it you need to use a thin object.

The system will return to factory condition. After the reset, you will have to configure everything again, which the above recommendations will help with.

This article will be useful for those who want to go into the settings of their router. Since most routers use the address 192.168.1.1 to log into the system, this guide will be universal and probably very popular. Regardless of what router we have and what parameters we want to change, we first need to log into the settings. Access the control panel. And you can do this at the address, or.

On routers from such popular companies as TP-Link, ASUS, ZyXEL, D-Link, Netis, Tenda, Totolink - everything is approximately the same. In any case, you can always find out the factory address. For example, look at it on the device case, or in the connection properties on the computer. We will return to this later.

If you don’t understand what this article is about, what these addresses are for, and what we’ll do in general, then I’ll try to explain. If you are in the know, then you don’t have to read what is written under the spoiler.

On Huawei it is usually 192.168.100.1. In the article I will show one method using which you can open a page with the settings of absolutely any router or modem. Even if you don't know his address. After all, it can be changed and not correspond to the factory one. Which is indicated on the device.

How to access 192.168.1.1?

On device (computer, laptop, smartphone, tablet) which is connected to a router or modem using a network cable, or a Wi-Fi network, you need to open a browser. Any will do. But I advise you to use the standard one. I will log into Windows 10 through Microsoft Edge.

In the line where site addresses are displayed, enter the address. Or http://192.168.1.1. To go, press Enter.

And if you entered the address correctly, the device is connected to the router and configured, then your router’s page will open.

At this stage, many people encounter a problem when the router settings page for some reason simply does not open. If this is your case, then see the solutions at the end of this article.

If a search engine page opens, make sure that you do not enter the address in the search bar. Or better yet, open it through a different browser.

I have an ASUS router and it asks for a username (Login) and password (Password) for authorization.

We indicate this data and get into the router’s personal account. Yes, many people call the web interface that way, but it’s not entirely correct. Your personal account is with the provider.

Another simple, universal and working method. On the computer, go to Explorer, to the “Network” tab. Our router should be displayed there. Right-click on it and select “View device web page.”

A browser will open with our router page. There is no need to manually search for anything, enter anything, etc.

Let's take a closer look at the authorization process. Many people in the comments ask about this. Not everyone understands what needs to be entered when the router asks for a login and password. And where can I get the login information for my router account?

Login to 192.168.1.1 via login and password (admin/admin)

Please note that the router does not always ask for a login and password. I will enter at factory settings. And if it asks, this does not mean that the default is necessarily admin.

  • On some routers, there is no authorization at the factory settings. The router system immediately opens. A window may appear asking you to set a username and password. And if not, then this can be done in the settings. I wrote about this in the article: .
  • If a request for a username and password still appears, then they should be indicated on the body of the router itself.

In my experience:

  • On TP-Link and ASUS routers, the default is always admin/admin. The address is usually 192.168.1.1.
  • On D-Link it can also be admin. Or the username is admin, and leave the password field empty.
  • On ZyXEL, the password is not set at the factory settings.
  • Netis – no authorization. If the login and password were not set by the user himself.
  • On Tenda, the web interface immediately opens. The password can be set manually.
  • Totolink – admin and admin.

Either way, a window just pops up asking for a username and password. It may look a little different. We indicate them correctly and go to the web interface. If not, an error will appear. If you change and forget this password, then reset the router settings to factory settings.

I can’t log into the router, what should I do?

It's not uncommon to have problems. There may be many reasons why you cannot access 192.168.1.1.

I'll tell you about the solution to the most popular ones.

1 Try the method I wrote about above in the article. When we open the router's web page through Windows Explorer. 2 Reboot your router. Try logging in from a different browser. When I can’t open the web interface, I first try to log in from another device. If it exists. 3 Next, you need to make sure that the factory address of your router is exactly 192.168.1.1. The address itself can be found on the router case. (must have a sticker with information). The factory "User Name" and "Password" are also indicated there.

If another address is indicated there, then go to it.

4 Be sure to check if there is a connection to the router. Even if the connection status is “Without Internet access,” the settings page should still open. 5 If you are trying to log in from a computer or laptop, check your IP settings. There should be automatic receipt of addresses. In the properties of a local network connection (Ethernet), or wireless connection. Depending on how you are connected.

If all else fails, reset your router to factory settings. But I can’t guarantee that it will help, you have to try. It happens that the router is simply broken, so the settings do not open.