home · Installation · Interesting ideas for a corrugated fence. Choosing fences for a summer residence: photos of interesting and practical options. How to install a fence from a profiled sheet in a suburban area

Interesting ideas for a corrugated fence. Choosing fences for a summer residence: photos of interesting and practical options. How to install a fence from a profiled sheet in a suburban area

One of the most budgetary fences for suburban real estate is a fence made of corrugated board. Due to the simple design and simple installation method, it is in great demand among Russians.

Fastening is possible in two ways. In the first case, welding work is required, and the second is bolted.

You can do the installation yourself. However, for convenience, it is of course better to take an assistant.

fence on poles

The easiest way to fix the sheet on metal posts that are buried in the ground. Pipes come in two types, round and square. It is easiest to work with square ones, they are also called profiled.

Its height is determined depending on the size you need, plus 1.5 meters for digging into the ground. Be sure to take into account that the pillar must fall below the freezing ground level. If this fact is not taken into account, then the fence may squint.

It is necessary to observe the required distance between the posts. By default, it is about 3 meters. Logs can be made of profiled pipe or wooden blocks.

The tree is not recommended for use, as it is not resistant to external environmental factors. Such a fence will last only a couple of years, but the cost will be much lower than that of a profiled pipe. Note that the wood before installation work should be treated with special solutions.

Log fastening types

With a holder. Basically, a wooden beam is attached in this way.

Side of the pillar. Here you will need to buy special holders.

In front of the column in the butt. Here you need to carry out welding work. A very laborious process, a lot of waste accumulates. And the design itself is very stable.

Either way, there will be waste. This is very difficult to avoid. Therefore, before buying, calculate the exact amount and take it with a margin.

Profiled fencing

For a person who has never encountered this type of material, it is very difficult to understand the markings. Each sheet is identified by a letter and a number. The letter means for which places it is intended, and the number is the size of the wave height. Marking C or A is suitable for the fence. The second is extremely rare. The best wave height is considered to be 8 mm.

However, if strong wind gusts are present, use 10 mm.

The standard sheet height is 2 meters. But, there are manufacturers who make it 2.5 meters high. Here, the width can be anything from 40 centimeters to 12 meters.

The material sheet can be painted or galvanized. Note that the painted sheet has a much longer service life, but the cost is orders of magnitude higher. And outwardly such a fence, while it looks richer.

All parts of the fence must be primed and painted, otherwise the service life of everyday life is very short.

Fastening the profiled sheet to the frame

This procedure is very simple. Absolutely anyone can handle it. The main thing is to choose the right mounting option.

And so, you can fix it with screws or rivets. The store sells special screws for these types of work. They are galvanized or painted. Usually they are matched to the color of the sheet, since they should not stand out against the main background.

The distance between the mount depends on the height and size of the ox. Experts advise fastening high if the sheet is long and the distance between the bolts is one wave.

The most important thing is to correctly set the first st, since all the remaining ones are equal to it.

Profiled sheets are very often combined with various types of fencing. They can also be decorated with various design elements. It all depends on your preferences.

Photo examples of a corrugated fence

There is such a psychological test: draw the house of your dreams. With its help determine the characteristics of a person's character. Particular attention is paid to how the participant in the experiment depicts the fence in his drawing. The more massive and higher this construction, the more a person is closed, does not want to let strangers into his inner world. Agree, it is not in vain that psychologists associate a fence with a spiritual barrier. In the domestic mentality, the idea that something secret is hidden behind the high fence is firmly entrenched. Did the neighbor build a new fence for the dacha? So, he got rich, he hides something from prying eyes.

Why is a fence needed?

In fact, the first thing the new owner of the summer cottage does is build a fence. This is a kind of symbol of the boundaries of private property. Anyone who is concerned about the question of how to make a beautiful fence on his hacienda pursues a specific goal. Do you know why people build them at all? First, we have already decided that this is the delimitation of two territories. Secondly, protection from attacks by neighboring living creatures, flocks of village children who dream of getting into someone else's garden. Do not discount the decorative value of the fence. After all, this is a very important element of decor, which should be in harmony with the general appearance of the site.

Types of fences

There are different types of fences, each of them performs its own design function. There is an opinion that their construction should be trusted exclusively to professionals. But if you are used to doing everything on your site with your own hands, then you can easily cope with such a task as erecting a fence. If your property is part of a protected holiday village, then in this case you can build a light fence, which will most likely perform a decorative function.

Next, I want to tell you about the varieties of fences. Let's talk about the main characteristics, advantages and disadvantages. I will comment on some points from the point of view of psychology. Remember what we talked about at the very beginning of the article?

This is a modern material that is very popular with summer residents. It is suitable for rural areas, its main advantages are durability and reliability. In the view of many owners, this is exactly what an ideal fence looks like, because it will not be easy for uninvited guests to overcome it. In fairness, I will say that the installation of this design is a rather troublesome business. Although it is not necessary to make a foundation for it, but the supporting posts for the fence must be driven into the ground by more than a meter. It is necessary to connect individual sheets by welding, and then paint and build a protective visor from rain on top.

Personally, I prefer the alternative corrugated fence. If a fence is made from this material, the result will be much better. Such a fence looks more expressive, somehow more romantic, or something. We get the same reliable and durable fence, but visually create the effect of openness.

A metal fence for a summer residence in the form of a picket fence can be made with your own hands. Of course, it will be necessary to take powerful posts dug into the ground as a basis, and between them on the transverse beams to fix individual corrugated sections. This is done in the likeness of the simplest picket fence. If you want to create the effect of a more massive fence, combine metal with natural stone or brick.

This combination somewhat hides the heaviness of the stone and adds openness to the site. Psychologists would say that a person who chooses this option is not in a hurry to put his life on display, but also does not hide his soul from others.

Natural eco-material is an ageless classic. It is always present in landscape design, and no new achievements in the construction industry will replace it. This fencing option will be ideal if your country house is a kind of fabulous hut - a wooden frame. The main principle says: the fence should be a logical continuation of the overall architectural solution. Do not be afraid of excess, feel free to complement the wooden cottage with a wooden fence.

See how harmonious the picture is? Full atmosphere of comfort and indescribable warmth. You can put up a wooden fence with your own hands if your country house is located in a forest area. In this case, it does not matter what material the main room is built from. Against the background of green crowns, a wooden fence will be a great solution.

Do not believe if someone tells you that a beautiful wooden fence will not last long. Building materials must be treated with special antiseptics that will protect the tree from pests. If the technology is observed and the subsequent care of the wooden fence becomes a good tradition for the owners of the site, then it will last for at least a quarter of a century.

There are many variations of wooden fences. Today it is fashionable to lay the bars horizontally. Or alternate such a "masonry" with a vertical one. The fence is a classic of the genre. The height of such a fence is regulated depending on the desire of the owners of the cottage. If the picket fence seems too open to you, you can make another layer of sheathing on the inside of it. The result is a double fence.

Plants love picket fence. Near such a hedge, they bloom and bear fruit well, because the sun's rays freely penetrate through the cracks. Traditional for domestic estates, a wooden picket fence looks very attractive.

By the way, it is actively used in European countries. As a rule, abroad these are low fences painted in snow-white color. Do you want to turn your dacha into a small Euro-capital? Use, for example, this simple idea.

By the way, from the point of view of psychology, a gardener who surrounds his plot with a wooden fence is a very positive person. The lower the fence, the more you are open to communication with others.

The main advantage of this variety is the relatively low cost. It is best to enclose a small suburban area with a net. Such a simple design technique will visually increase the area, make sunlight more accessible for plants. As a material for building a mesh fence with your own hands, use a plastic, metal or metal-plastic mesh. If you are not satisfied with the appearance of such a fence, plant climbing annuals along it. Kill two birds with one stone: get a cheap but reliable live fence and decorate your yard with flowers.

I really like the ethnic style in the design of suburban areas. If you want to recreate the atmosphere of a remote provincial village on your hacienda, try making a wicker fence with your own hands. This is a very simple, one might even say, primitive technology, which was actively used by our ancestors a couple of centuries ago.

You can use a vine, thin branches of trees that bend well. A beautiful wattle fence can be created like a basket by staggering vertical and horizontal rods. This decorative hedge can also find its place inside the site, separating the territory of the front garden or flower bed. Its advantage is that air circulates perfectly between the rods. But such a fence is not durable, it needs to be redone every about five years.

Here, perhaps, are all the main types of fences that a simple amateur summer resident can build with his own hands. Concluding the topic, I would like to recall once again a simple psychological technique. When planning the construction of a fence on a hacienda, try to find a middle ground: do not try to separate yourself from the outside world with a high wall, but you should not expose your life to all the curious.

Photos of fences for giving

















Watch the video on how to make a chain-link fence with your own hands!

Fence at the dacha

A fence is a building envelope, the main functions of which are to mark the boundaries of private property and protect the courtyard from the intrusion of unwanted guests. A good fence copes not only with these tasks - it concisely completes landscape design, complements the decoration of a residential building and speaks of the respectability of the owner of the site.

Corrugated fence

What kind of fence is considered good for giving? First of all, the one whose costs justify the quality. Do-it-yourself economy fence in the country house is easiest to assemble from corrugated board.

A fence on a summer cottage made of corrugated board is the perfect combination of price and quality

There are several advantages to such a fence.:

  • Affordable price;
  • Durability;
  • Wide palette of profiled sheet colors;
  • Ease of assembly;
  • Unpretentious care (it can rain to wash the fence).

We build a fence from corrugated board according to the following instructions:

  1. We dig holes for supporting pillars with an interval of 2 - 2.5 m and a depth of 0.8 - 1.2 m.
  2. Sprinkle the bottom with crushed stone until a layer 20 cm thick is formed.
  3. We put the metal bearing part, controlling the evenness of the supports with a building level.
  4. We fill the pits with a concrete-sand mixture (we prepare the composition at the rate of 1: 8).
  5. We wait for the solution to harden and weld two diameters from the professional pipe to the pillars.
  6. We use self-tapping screws to fasten profiled sheets with lags.
  7. We love the fruits of our labor.

As you can see, it is really possible to build an economy class fence in the country with your own hands. And quickly and at no extra cost.

Metal fence

You can enclose the summer cottage with a metal fence. We draw a design diagram, purchase materials and connect them with a welding machine. The procedure for creating an iron fence is similar to making a fence from corrugated board, but the difference is only in the sheathing. The spans will be created either from a grid or from metal rods. In the course of creating the frame, we grab the parts by welding.

The peculiarity of a metal fence is that it is not necessary to make a foundation for it.

In order for the fence to be in harmony with the site and the residential building, we make it forged, mesh, sectional or with corrugated sheet.

A wrought iron fence does not belong to the economy class, and in order to build it in the country with your own hands, you will have to tinker a lot. Fences assembled from metal rods are budget structures. But they are not deaf, so the courtyard will be visible to people passing by.

Plastic fence in the country

An innovation in the improvement of the suburban area is a plastic fence. Its installation will be mastered by anyone who has experience in assembling structures from plastic profiles and PVC boards.

The construction of the fence is made of plastic, increased strength, which is not afraid of blows.

There are many advantages to plastic fencing.:

  • Small price.
  • Easy care.
  • Easy installation.
  • Aesthetic appearance of the finished product.
  • Resistant to fire, deformation, moisture.
  • The ability to retain color despite precipitation and heat.
  • The ability to create different variations of the fence - a blank wall, a fence, an imitation of a picket fence, etc.
  • The fence does not dry out, does not crack, does not deteriorate by insects.

brick fence

The construction of a brick fence is a responsible job and requires compliance with certain rules. But the owner receives for his efforts a high-strength beautiful fence with a long service life. A rich assortment of bricks allows you to create a fence that organically complements any exterior.

A well-built brick fence can even withstand a hurricane!

We build a brick fence in the country as follows:

  1. We measure the length of the future structure and create an estimate for materials.
  2. We mark the territory and dig holes for the strip foundation.
  3. We fill the base immediately, as soon as the supporting pillars are placed.
  4. In order to avoid the formation of joints and increase the strength of the structure, we make the foundation in one approach.
  5. On the frozen foundation we are engaged in laying bricks. We arrange them in one row, but if you want to show creativity, we use combined or openwork variations. For a high fence, we make a double-row masonry.

If you have never worked with bricks, engage a specialist to build the fence, since the laying of the material requires scrupulousness and control over the evenness and thickness of the seams. In the absence of sufficient experience, the design may turn out to be sloppy and weakly stable.

Chain link fence

As soon as chain-link mesh was first used to make a fence, consumers of building materials immediately realized that this is an ideal option for a translucent fence that can be placed on the boundary and not be afraid of quarrels with neighbors about shading their plantings.

A chain-link fence is ideal for a fence between neighbors, because by law, deaf high fences are prohibited

The range of metal mesh is represented by three varieties:

  • Galvanized;
  • Not galvanized;
  • Plastic coated.

We immediately sweep away the bare non-galvanized version, since the operation of such a fence will be minimal. Simply put, rust will quickly “eat” it. A PVC chain-link is more suitable for warm regions and coastal areas, since plastic protects the mesh well from moisture. But this material is not resistant to temperature extremes. This means that a galvanized mesh will be a more or less durable solution.

We work with the material like this:

1. We begin the construction of this fence by marking the location of the supporting parts. We set the intermediate pillars in compliance with a distance of 3 m, tension - with an interval of 9 m. For the bearing part, we take iron profiled pipes Ø 60 mm and corners 50 mm or more.

2. Under the intermediate columns, we drill the ground with a drill until the required number of holes are formed with a depth of about 40 cm. For tension poles, we make recesses of 60 cm. We will not engage in concreting on clay soils and soils with an admixture of clay. They are prone to heaving, and this is dangerous by cracking the concrete base in winter. When working with pillars, we concrete sandy soil and light loam.

3. As soon as the tension poles take their places, we connect them to other supports using a metal corner, bolts and welding.

4. If we put only intermediate posts as a bearing part, the mesh fabric will be well stretched. But the design will not be reliable, because the sheathed bottom is easily lifted and not only an intruder, but also a nimble child can penetrate into someone else's summer cottage.

Let's protect ourselves from uninvited guests as follows. We pass a wire rod with a diameter of 3 mm through the cells along 3 horizontal levels. To tighten it, we drill 3 through holes in each column.

5. We fix the chain-link on the pillars. We put the roll vertically at the support post and check where the bent ends of the lines are (they should be at the top). We attach the top line of material to the top of the column and go to the next support, slowly unwinding the roll. We pass the wire rod through the grid between adjacent columns and insert the ends into the holes. We stretch the wire and fix it with tension bolts. The work is over.

Wooden fence options

The traditional version of the design for fencing the site is made of wood. All the subtleties of making wattle fences, picket fences and slab fences are transferred from experienced craftsmen to novice craftsmen. This familiar trinity is joined by a modern design - the "American ranch". Consider the construction of these fences.

Wattle

To create a strong dense wattle fence, you need to stock up on branches, poles, pipes. If the bearing part will have a diameter of about 8 cm, then for spans it is better to take:

  • Willow;
  • Willow;
  • Flexible vine;
  • Birch or poplar rods.

Wicker fence is traditionally made from improvised means - existing branches, vines, sticks

In order not to wander through the clearings, you should look for building materials under your feet. Surely in the garden there are pruning branches of berry trees and hazel. The only condition is that the branches must be cut at an angle of 60 °. But the best wattle is obtained from a freshly cut vine.

We use the wooden material collected in the country for the construction of the fence as follows:

  1. For the bases, we prepare larch logs. Their number is determined by the number of the future fence. Based on the estimated thickness of the weave, we observe an interval between supports of 50 cm. If you have thick rods, make the distance larger. Stick to it almost to the end, and only place the last 3 logs 20 cm apart.
  2. Impregnate all wood with a protective compound, treat it with fire and resin. With special care, work out the bottom of the pillars, which will remain underground. These actions will prevent damage to the wood.
  3. Weave the bars of the future wooden fence in the country house between the posts. Drive the first branch into the ground 15 cm, holding it upright. The remaining rods, regardless of location, braid with wire around the frame. Fix the thick end of the rod first, and bring the thin end along the post through the fixed vines. Every 4 rows, tap parts of the canvas with a hammer. Brittle stems collect in armfuls of 5 pcs. Hide the edges and cut ends inside the hedge.
  4. Open the finished structure with varnish, decorate with clay pots, or plant weaving plants along it - a decorative rose or leafy ivy.

Fence

The picket fence is a ventilated fence made of wooden planks, which makes it easy to delimit the cottage. We begin its construction with fixing the supporting elements, for which we will take profiled iron pipes 60 x 60 mm. After concreting the holes, we are engaged in lags. We weld the diameters on the rods with an overlap and clean off the excess welding. We carefully prime the structure and paint it in a suitable color.

Wooden picket fence at their summer cottage

Next, we install gates and gates and equip them with fittings. We cover the ends of the pipes with plastic plugs - they will protect the inside of the supports from moisture and corrosion processes. We attach wooden planks to the crossbars using self-tapping screws. For even spacing, keep a distance of 3 cm.

To improve the general appearance of the fence, we cover its top with a ridge-shaped plank structure. As a result of making it with our own hands, we get a ventilated version of the economy fence, through which air flows easily pass - this is important for plantings growing in the country.

Slab is lumber, one of the side parts of which is propylene, and the other is either not propylene at all, or propylene is not over the entire surface. Logs belong to the waste of wood processing at the sawmill, so this material allows you to save on filling the spans. Despite the outward simplicity, the slab creates an imitation of a tree, and the owner gets a nice cheap fence.

Slab is essentially waste. Therefore, we can note the low cost per cubic meter of slab

Consider how the slab is used in the construction of the fence.

  1. Bark removal. The debarking of the material is an important point in the preparatory work. You can’t skip it, otherwise the bark beetle will ruin the fence. We rid the slab of the bark with a flat shovel with a sharp blade, a carpenter's ax and a scraper. Then we sand the cleaned surface to perfect smoothness and apply several layers of antiseptic.
  2. We put metal or wooden support poles. In the second case, we take logs from pine, oak or larch. The optimal trunk diameter is 20 cm, length is 2 m. We cover the bottom of the pillars with hot resin or a Kuzbass-lacquer solution. When erecting a fence with girders, we leave a space of 2.5 m between the supports.
  3. On loamy soils, we drive in pillars without strengthening measures. We drill the mounting points with a drill and hammer the supports with a sledgehammer. When carrying out work on sandy or chernozem soil, first we dig holes, the diameters of which are twice as large as this parameter of the pillars. We cover the bottom with gravel and tamp the poured 10-centimeter layer. We place each post in the center of the hole and fill it with gravel. The position of the bearing parts is controlled by a vertical level.
  4. Sheathing can be done in any direction. First, we leave small gaps between the parts of the material, but later we also close them with a slab, and again with a convex surface outward.
  5. We cover the finished fence with paint or varnish.
  6. We protect the ends of the pillars with iron or plastic cones.

With a horizontal arrangement of the material, we attach the timber to the supporting pillars, nailing it on both sides with nails or fixing it with overlapping screws. To perform vertical plating, we saw the slab across, and with the runs we hook it with the convex side.

American style wooden fence

Assembling an economy class fence in the country with your own hands in the style of an American ranch is a simple matter. But first, all wood material must be treated with an antiseptic, paying special attention to the ends of the pillars buried in the ground. Then we make markings along the perimeter and hammer in the supports for the “ranch” fence at the corners of the outlined rectangle. As usual, we put the pillars in the holes and concrete. The hardened solution is masked with soil.

American style fence

To control the horizontal position of the boards between the pillars, we stretch the rope. It will not allow installation curvature and will help to adjust the height of the intersection filling. We drive in intermediate supports, leaving 2-meter voids, we check their verticality with a level.

We attach the crossbars to the supports with nails and self-tapping screws. The product is varnished. We color it at will.

The foundation is the head of everything

Both a powerful stone and a light wooden fence in the country require a solid foundation. With its competent filling and the correct location of the supports, the enclosing structure will protect the site for more than a dozen years. The foundations for the fence are divided into tape and pole. Let's consider each type separately.

Strip foundation

This type of foundation is advisable to fill in the following cases:


We begin work on creating a strip foundation by digging a trench with a depth of 30 to 80 cm. If the soil is unreliable, we go deep by 1.5 m. We make a “cushion” of sand and gravel, generously pour water and tie the reinforcement. We form the size of the cell at our discretion.

We erect the formwork so that the fence canvas with the ground subsequently separates 30 - 50 cm. We fill the formwork with concrete mortar. In the case of using pillars under the bearing part of the canvas, we place and align the supports even before pouring the foundation.

Pillar option

The post base is an economical solution that perfectly holds light fences. When constructing a wooden fence for a summer residence on a pole foundation, it is imperative that we process wooden parts with a special composition that protects the material from decay. With the right approach to the construction of a pillar-type foundation, we get a high-quality foundation that is in no way inferior in terms of durability to a strip one.

Photo of the pillar foundation

The filling technology is as follows:

  1. A drill swarm of pits for load-bearing parts, deepening a meter and a half. We expand the diameter of the holes by 15 - 30 cm in relation to the diameter of the columns. Based on the intended width of the spans, we maintain an interval between supports from 2 to 3 m.
  2. We create a “pillow” either from pure sand, or from its mixture with crushed stone. Plentifully water a 20-centimeter layer.
  3. Align the posts in level and fill the holes with cement mortar to the top. The mixture is supplemented with crushed stone as desired.

As a result of our work, cemented pillars were obtained. Now we fill in the spans. We stretch the chain-link mesh immediately. But if the canvas requires stuffing of material, we first fix horizontal guides between the supports (transverse logs, cross-sections).

How to decorate a fence in the country

If you spend a lot of time in the country, you will probably get tired of looking at the boring flat surface of the building envelope, especially the deaf and long one. Planting climbing plants along the fence (according to the principle of vertical gardening) will help to decorate the fence and make it alive. For this purpose, girlish grapes, actinidia, aromatic hops with beautiful cones are suitable.

Decorating the fence with flowers is a great solution

You can braid the fence with annual plants. Only for their upward movement, it is necessary to take care of the vertical supports in advance, so that the loaches reaching for the sun have something to grab on to.

The visual separation of a long fence is facilitated by decoration with flower beds. Several flower beds are placed equidistantly above the ground and "dilute" the monotonous structure with bright flower stalks.

You can fill the flower beds with shrubs with variegated leaves. It is not forbidden to plant conifers for decorating a deaf fence, but they are sensitive to the bright sun. For this reason, flower beds with them will have to be placed on a shaded section of the fence.

If you have the ability to draw, the fence can be painted by skillfully painting it with bright colors. Small architectural forms will look attractive next to the fence - garden figurines, fountains, swings, gazebos, etc. Turn the fence into a gallery by hanging paintings, posters, crafts along the canvas.

Decking can also be originally decorated

If it is possible to get seeds of bacopa, petunia, lobelia, dichondra, pelargonium or hanging begonia, plant them in pots and hang a strict blank fence with blooming fragrant flower pots. Ampel plants will delight you all summer.

There are many options for building a wooden fence - from very simple, but cute and original, to luxurious

Nowadays, high deaf metal and stone fences are “in fashion”. Even in summer cottages, a neighbor often strives to isolate himself from his neighbor with a "fortified wall." The other extreme is the “budget” chain-link fences, which may protect from freely grazing living creatures, but they rarely add beauty and grace to the dacha. Meanwhile, there are many options for building a wooden fence - from very simple, but cute and original, to luxurious

Even a novice master can build the most ordinary wooden fence if he knows how to handle a hammer and a hacksaw. Add a little imagination (or use one of the suggested ideas) - and you get a real decoration for a summer residence, and not just a fence around the site. It might look like this...

Bright and funny

For those who love bright colors, have an extraordinary sense of humor and want to create something completely unusual from available materials, a multi-colored fence is a real find. You can make it from almost anything - take a look and see for yourself:

The various elements of this palisade do not violate the harmony at all - a successful color scheme "gathers" the entire structure together. What in a different form, perhaps, would look like “production waste”, becomes almost an art object :))

In different colors, you can paint a traditional fence made of a simple picket fence. And here the scope for a flight of fancy is unlimited: the choice of colors and their combinations is solely a matter of taste. We want to make it brighter, but if not, we will choose delicate and translucent “watercolor” shades. We can stop at one or two colors, or we can use a whole palette.

Some find inspiration in a box of crayons - and look what a wonderful fence!

Having decided to implement such an idea, do not spare money for good colors: not only juicy and bright, but also resistant to adverse weather conditions. After all, we are building a fence for more than one season, and it will be a shame in the spring to find a peeling and faded beauty.

And it’s worth considering: such a fence is not suitable for every site. Still, the color is binding. Such a structure is impossible not to notice, it will set the tone for the entire environment, and it is important to choose this tone correctly.

Simple but elegant

Those who prefer a discreet, calm design in the spirit of classic garden traditions also have plenty to choose from. Let's take paints of discreet colors and shades and focus on the elegance of forms.

It is not too difficult to build an ordinary fence from a picket fence or simple boards - the whole process is described in detail in the article Prose of Life: a wooden fence with your own hands. And then there are the details. So, the white color makes even the most unpretentious fence stylish and elegant, like this:

Does white seem impractical? Or maybe you don't like it when the fence is "bumpy" and want to make it less noticeable? Use discreet and deep shades of gray, blue, green.

Want something more original? Let's change the shape - for example, make vertical elements of different heights. The contours of the fence can be any - it does not change the essence. Most importantly, such an “improvement” will not be too time-consuming and complicated.

But this is an option for experienced craftsmen. You can’t call it simple in execution, of course, but no one else will have it for sure, and the owners will be rightfully proud of their beautiful, original, elegant and unusual fence.

But these are all ideas of "transparent" fences. If you want to hide from immodest glances, you can use another idea: let the lower part of the fence be solid, and the upper one - “transparent”. Strict gray color will emphasize the solidity of the first, and airy white - the lightness of the second. All together - practical and very stylish, don't you agree?

But in general, who said that the elements of the fence should be attached strictly vertically? It will not be much more difficult to build such a lattice fence - if the sections are not made too bulky. It looks much better than the traditional one. Those who love solitude can use such a fence as a support for climbing plants - they will hide your country world from the attention of strangers.

For zoning the space inside the site, you can use the same idea in a “lightweight” version. It, among other things, is also economical: such a design will require less building materials than the usual vertical one.

If desired, such lightweight sections will serve as mobile partitions - it is enough to make strong pointed posts for each of them and not fasten the sections together (or provide for a collapsible, removable mount). This is an option for those who are just starting to plan a site and are not yet sure of the solutions found. A mobile fence will not limit your creative search - after all, at any time you can change its location, move the boundaries.

Luxuriously

The following ideas, perhaps, no one will call simple. Their implementation will require both funds and excellent skills in working with wooden structures. But the results are simply amazing. Perhaps these photos will give inspiration to some of the experienced craftsmen, and the result will be something luxurious and stylish.

The idea of ​​connecting a fence and a pergola in itself deserves attention. If you like to use climbing plants in garden design, including for decorating a fence, as described in this article, such an idea will surely not leave you indifferent.

White color will make a massive structure less cumbersome, give it lightness. In the next version, flower boxes crowning the structure are also interesting (however, from a practical point of view, this raises questions: caring for plants in such containers will not be easy)

Well, the next idea is simply amazing. Of course, the fence itself for its implementation must have a considerable area - then the result of the work will make a proper impression. But perhaps the idea is suitable for a more modest scale. In any case, the spectacle is spectacular!

In general, a luxurious fence does not have to be built of stone and metal)) “Democratic” wood in skillful hands turns into genuine masterpieces, as we could see.

Good and reliable

Alas, our reality is such that a fence is often built not for beauty, but for a purely practical purpose - to protect your territory and property from uninvited guests. And here the main criteria are the strength and reliability of the structure. Yes, high deaf fences are often erected “not from a good life” ... But such a fence can also be beautiful!

Here, for example, is the idea of ​​how to "revive" and decorate a solid wooden fence: a small decorative lattice, bordering the perimeter fence, noticeably transforms it, you see.

And in the next photo - a compromise solution. On the one hand, the fence is solid and monumental - on a concrete base, with concrete pillars, quite high. But the small gaps between the boards make the structure visually lighter, and the delicate colors support this impression.

Pay attention to the shape of the vertical elements: rounded tops - such a trifle, it would seem - change the appearance of the entire structure.

Rustic

For a garden-garden in country style, appropriate fences are very appropriate. Of course, they do not hide anything and do not protect from anyone, except that they mark the boundaries of possessions. But they look great in the right environment! For those who do not like life behind the "fortress wall" - a very simple fence made of birch poles.

This idea can be applied in the zoning of the site. If such a solution seems too radical for an external fence, use stylized "rural" fences to separate, for example, a garden from the rest of the territory or designate a recreation area

A more complex, but also more effective option is presented in the next photo. Material - thick branches, snags, small logs. There is no need to achieve clear lines and complete symmetry - the material itself dictates the nuances of form.

Wattle - a traditional type of garden fence, rooted in antiquity. Nowadays, such a fence looks impressive and stylish, and you can use it almost everywhere - by choosing the appropriate accessories and design.

Moreover, the wattle itself is not so simple - with some skill and patience, you can give it an unusual and unusual look using original methods of weaving rods. True, the preparation of material for wattle will take some time, and the process itself may not seem too simple at first - but only at first. No wonder they say: "Eyes are afraid - hands do"

If there is absolutely no desire to engage in such “needlework”, but you like wattle, look for ready-made sections in specialized garden centers - they are easy to install and do not require a serious investment of time and effort from the owner of the site.

Usually fences mark the borders, act as a protective fence against the penetration of unauthorized persons and animals. With the advent of various materials on the market, it became possible to install many interesting hedges that could decorate a summer cottage. And there are also fences for, fences for zoning space, fences for animals, decorative, photos of which are full of on the global network. Therefore, the desire to build a strong, and at the same time attractive barrier becomes quite natural.

Read in the article

Types of fences for giving by design

Regardless of what function the protective structure performs, its design consists of two elements:

  • load-bearing supports- fixed in the ground vertical, horizontal runs (lags), gates, gates;
  • sheathing- material that fills the spans between the pillars.

The load-bearing elements of the fence bear the main load and are responsible for its strength. They are chosen based on the characteristics of the soil, wind loads of the area and the style of the suburban area. Sheathing materials give a decorative look to the entire structure and can be made of metal, plastic and other products.

Advice! Strong winds are often observed in open flat areas. In such areas, the fence sheathing is under increased stress. In this case, it is recommended to make a fence in the country house inexpensively with gaps in the sheathing. A more difficult option is to install a powerful foundation for load-bearing supports.

Depending on the function performed, the design of the barrier can be of several types:

  1. Open. The fence is installed in order to avoid the adverse influence of environmental factors: from the arrival of vehicles, the departure of children from the territory of the dacha, the creation of an unauthorized dump, etc. An open fence has large gaps and does not give a shadow. Near it it is good to plant crops that need sunlight. It can be either high or low.
  2. Deaf. The fence of this type is a high capital structure without any light gaps. It is built to protect against prying eyes, intrusions of strangers and vagrants. The advantages of a massive structure are the reduction of external noise, the reduction of the penetration of roadside dust, the possibility of planting shade-loving plants. Usually summer residents plant fruit, coniferous or ornamental trees along such a fence.
  3. Combined. A fence of this type combines decorative details, open and deaf elements. It is being erected in order to continue the stylistic idea of ​​\u200b\u200bthe summer cottage and. The design can be both simple and complex, both low and high. During the construction, various technologies and materials of different types can be used.

Fences for giving: photos of finished fences

Each owner of the cottage has a desire to create comfortable conditions for recreation. The first step of these actions is the fencing of the site. A well-chosen fence will not only decorate summer cottages and give them completeness, but will also fulfill its functions.

There are too many barrier options. There are fences high and low, massive and symbolic, made of metal, improvised materials or plastic. And how to answer the question, which fence to choose? For giving important requirements to a fence are its durability and durability. And they depend on the bearing pillars and sheathing materials.


When choosing a country fence, an important factor is the legislative norms that must be taken into account before installing the fence. For example, fences that are too high and deaf should not be erected, as they will give a shadow to the neighboring plot and the plot of the dacha owner. The same fence should not protect the territory of a summer cottage of a small area. From the outside it will look ridiculous.

Original and economical do-it-yourself fences from improvised materials

A dacha is a place where you can show creative imagination when installing a fence. Using improvised materials, it is quite possible to get a cheap design. The most common items are taken into consumption: sticks, logs, plastic bottles, remnants of building materials, tree twigs. The result is a creative fence for giving. Cheap, created with your own hands, it will attract attention and will be a wonderful piece of decor for your summer cottage. And thanks to the variability, the fence and the exterior of the cottage can be changed as much as you like.


A fence made of car tires looks very stylish. Stacked in a checkerboard pattern to a certain height, they form small ledges. Soil is poured into each such gap, and plants are planted. A well-thought-out composition of flowers and grass will turn a dull gray “wall” into a colorful fence.


A laborious but simple job will be weaving a fence from tree rods, straw or reeds. A wicker fence will be a spectacular addition to a rustic rustic design. To create such a fence, dry material of different thicknesses will be required. A fence made of willow, vine or hazel, with proper care, will delight for 5-8 years. Wattle made of reeds or cattail will decorate the cottage for 3-4 years. From rods and branches, you can also build a fence for, flower beds, garden, recreation areas.


Advice! In order for the wicker fence to last long enough, it is necessary to treat the wood material with an antifungal compound, cover it with paint and varnish it.

Another budget option for a country fence is a slab hedge. This material is cheaper than processed boards and can be easily purchased at woodworking enterprises or a sawmill. The procedure for erecting a fence is very simple: the raw one is nailed to the transverse bars fixed on vertical posts. To preserve the natural beauty, the slab is varnished.


Cheap hedges made from improvised materials on a suburban area look spectacular. In the general style performance, they create an atmosphere of peace, home comfort. There are a lot of options for creating such fences. Home craftsmen willingly post photos of fences with their own hands from improvised materials on the Internet. After studying them, you can figure out how to make a fence cheaply. But there is one caveat - the service life of such fences is relatively short.

Do-it-yourself installation of a wooden fence in the country house: photo designs

The wood is the best material. It is inexpensive, environmentally friendly, easy to process, and commercially available. If you correctly choose the type of wood and choose the necessary design of the fence, then you can build fairly strong fences with your own hands cheaply and for a long service life.


Advice! Without proper treatment, a wooden fence will dry out, rot and gradually collapse. Treating with protective impregnation and regular painting will help to avoid the appearance of cracks and crevices. At the same time, the appearance of damaged fence elements is inevitable, but they are easily replaced or repaired.

From a tree for a summer residence, you can make dozens of options for decorative fences with your own hands. A photo of an openwork wooden fence, painted with white paint, clearly demonstrates an attractive look.


Such a fence on a personal plot is applicable for zoning or as a decorative element. It does not differ in strength, but it stands out for its ease of manufacture. The fence is created by crossing narrow rails.

The classic version of a wooden fence for a summer residence is a picket fence. It is quickly erected and well delimits the site, which perfectly demonstrates the photo of the fence from the boards with your own hands:


Its design is very simple - these are vertical boards that are nailed to horizontal veins. Light penetrates well through the boards, so that different crops can be planted near it.

To create a wooden fence, you can use boards, slats, planks, supports of various shapes and sizes. And in order to understand how to make fences from these components with your own hands in the country, you should consider the design.


Varieties of metal fences for summer cottages

No less popular options for fences for summer cottages made of metal. These are forged spans, chain-link fences, structures made of reinforcing bars and. Such structures have great strength and durability, for a long time they will not require repair. Unlike wooden fences, metal fences are difficult to install and costly. For example, forged fences are made in a forge or at a factory in the form of separate sections, and their installation requires considerable effort and additional equipment.


The list of popular materials for the manufacture of fencing includes corrugated board. Photos of fences for giving from it are quite often invested in networks. The advantages of such fences are a deaf design that does not allow outsiders to view the summer cottage, and resistance to atmospheric phenomena. Profiled sheets come in different colors, may vary in texture and wave size. A simple hedge of this material is easy to install, but it looks dull. For a solid look, it is better to install corrugated board on a columnar one between metal or supports.


A good alternative to corrugated board is. Fences for giving from this material have a translucent appearance and look much better. They are easy to install and do not belong to high-value goods. On the market, the picket fence is presented in a wide range of colors and various shapes. In accordance with the design of the site, a metal picket fence can be installed on concrete or attached to metal supports.


The wealth of forms of plastic fences for summer cottages: photo gallery

PVC fences on the construction market appeared not so long ago, but today they have taken a worthy position. This was facilitated by the practicality of the material, attractive appearance and ease of installation. On sale plastic fences are presented in a wide range of colors.


Advantages of plastic fences:

  • a light weight;
  • weather resistance;
  • the possibility of combining with other materials;
  • a variety of decorative forms;
  • high performance.


You can buy a plastic fence for a summer residence not only for fencing the territory, but also for decorating front gardens, flower beds, etc. PVC fences are produced in the form of ready-made typesetting sections that can be pointed at each other. They can also be multi-section, representing a single product for installation in the span.


Related article:

An ideal solution for fencing a site, which will not only perform protective functions, but also delight the eye with its beauty and shape. How to choose plants, what are the nuances in planting and caring for them - read our article.

Fences for giving cheap: prices and photos of popular types

Due to the specifics of the dacha territory, some types of fences are erected in many personal plots. Focusing on their own needs, the owners of country houses pay attention to the definition of boundaries, the reliability of the material, the appearance and combination with the country landscape. But when buying, the emphasis falls on one point. For example, if you only need to enclose the territory with your own hands cheaply, a fence for a summer residence (photo from the table) can be chosen in the form of a light structure. If the issue of safety prevails, then a strong and massive structure is needed. But in any case, the fence should look aesthetically pleasing and decorate the site.

Review of inexpensive fences for summer cottages: prices are indicated taking into account the installation of the enclosing structure

Image Name Description Material Average price, rub.

wooden fenceProduction of fences: deaf type, picket fence, blinds, palisadedry boardfrom 700.00

RabitzSold in rolls, the price is affected by the cell sizesteel wirefrom 400.00

Corrugated fenceThe cost of a fence from corrugated board is indicated, price per meterProfiled metal sheetfrom 700.00

Welded mesh fence 2D and 3DFinished section of welded rodsGalvanized steel barfrom 500.00
plastic fenceSolid fence section with picket fencePVCfrom 3300.00

Decorating fences: original ideas

A modern dacha for many owners is a place of relaxation and solitude. Therefore, each owner seeks to decorate his territory. The decor of the fence is an integral part of this decision. After all, a stylishly designed hedge will be a concise completion of the country landscape.

Climbing plants will look very impressive on the fence. Growing from year to year, they will look better. Loaches will decorate a fence of any kind, except for a low one: wooden, forged, plastic, brick. Parthenocissus, ivy, hops, climbing roses, sweet peas are suitable for planting. From the side of the yard along the fence you can plant tall flowers.


A wooden picket fence needs to be varnished or painted from time to time. Why not paint it with bright colors? With a good imagination, a multi-colored fence becomes an art object.


A dull mesh or lattice fence will be transformed if it is “embroidered” with bright ribbons. This does not require special skills. It is enough to find a pattern and start weaving. As the colored ribbons burn out, the pattern can be completely changed. And a blank fence can be decorated with multi-colored plastic bottle caps, laying out a pattern like a mosaic from them.


Each summer resident will surely have unnecessary plastic boxes, containers, old boxes, rubber shoes, children's buckets. From these things it is easy to build shelves for flowers, and even flower ones. Having nailed them on a wooden fence from the side of the yard and placing plants on them, you get a non-standard decoration of the fence.


There are a lot of ideas for decorating fences. Below are photographs, fences for giving, which are decorated effectively and without high costs.



Article