Baxi luna duo tec 40 technical specifications. Gas system
Wall-mounted gas double-circuit boiler Baxi LUNA Duo-tec+ 40 GA with a power of 32 kW, heating area of 320 m2 is intended for heating and hot water supply in administrative and residential premises.
Luna Duo-tec series boilers are equipped with a two-speed pump, which is controlled by the boiler electronics and a burner with a wide modulation range.
A distinctive feature is the completely soundproofed combustion chamber, thanks to which the boiler operates silently, which significantly expands the possibilities of installing equipment in a house or apartment.
Advantages:
Adaptive Combustion Control System
Power modulation ratio - 1:7
Retains rated power when inlet gas pressure drops to 5 mbar
Continuous electronic flame modulation in heating and domestic hot water modes
Reduced CO and NOx content
Burner made of stainless steel AISI 316L with pre-mixing of gas and air
Can be reconfigured to run on liquefied gas
Hydraulic system:
Energy saving two speed circulation pump With electronically controlled and built-in automatic air vent
Primary heat exchanger made of AISI 316L stainless steel
Secondary plate heat exchanger made of stainless steel ( dual-circuit models)
Automatic bypass
Pump post-circulation
Inlet filter cold water
Built-in electric three-way valve (including single-circuit models)
Temperature control:
New control panel with wide display
Two heating temperature sensors on supply and return
Self-adaptation of weather-dependent automation
Temperature control range in the heating system 25-80°C
Built-in weather-compensating automation
Regulation and automatic maintenance of the set temperature in heating and hot water circuits
Digital temperature and pressure display
Ability to control multi-temperature zone systems
Control and safety devices:
Electronic pressure gauge - triggered when water pressure drops in 2 stages: warning and blocking (0.5 bar)
Electronic self-diagnosis system and storage of the latest operating errors
Ionization flame control
Pump and 3-way valve blockage protection systems
Protective thermostat against overheating of the coolant in the primary heat exchanger
Control safe removal combustion products using an NTC sensor
Safety valve in the heating circuit (3 atm.)
Frost protection system for heating and hot water circuits
Key Features:
Power: 32 kW
Heating area: 320 m2
Number of circuits: dual circuit
Installation type: vertical
Combustion chamber: closed
Heat exchanger material: stainless steel
Voltage: 230 V
Capacity: 22.9 l/min
Fuel consumption: 3.36 m3/h
Efficiency: 107.6
Temperature range in the heating circuit: 25-80 °C
Adjustable temperature range in the DHW circuit: 35-60 °C
Volume expansion tank: 9.1 l
Acceptable operating pressure: 19.1 bar
Chimney diameter: 60/100 mm
Dimensions (HxWxD), mm: 763x450x345
Weight: 41 kg
Contact our specialists and get advice on how to choose and buy the right Baxi gas boiler, as well as order delivery and installation by optimal cost.
Our manager will guide you through the characteristics of the boilers, clarify prices and availability.
You can get a discount on the price if you buy from us gas boilers Baxi wholesale or order boiler room installation and maintenance services.
- Delivery in Moscow 500 rub.
- Delivery within Moscow Region: 500 rubles + 50 rubles/km from the Moscow Ring Road
- Delivery across Russia - transport companies
- Pickup: free
You can always indicate a delivery date that is convenient for you (but not less than two working days) when agreeing on the order. Delivery of goods is carried out from Monday to Friday from 12:00 to 18:00
Delivery at a later or earlier time interval is agreed individually with the Buyer and is carried out for an additional fee.
Delivery on Saturday, Sunday and holidays (by agreement)
Delivery on weekends and holidays is carried out at the request of the buyer, upon confirmation of the application 2 working days in advance.
Delivery on weekends and holidays is carried out at the buyer's request for an additional fee, upon confirmation of the application 2 working days in advance.
Pickup
You can pick up your order yourself at the pick-up point at Podemnaya St., 14, building 37.
Pickup of goods is carried out daily except Saturday, Sunday and holidays after confirmation from the sales staff.
Delivery terms
Delivery of orders placed through the Ecolife online store is carried out to the entrance or to a place where a truck can freely drive up and where goods can be unhindered, as well as to cargo collection points by transport companies carrying out transportation to the regions.
The delivery driver can provide loader services only by prior arrangement for an additional fee.
Upon delivery to the Buyer, the Seller is responsible for appearance goods until the moment of acceptance and transfer to the Buyer. Claims regarding the appearance and configuration of the delivered goods, in accordance with Art. 458 and 459 of the Civil Code of the Russian Federation, can only be presented before the goods are transferred by the Seller to the Buyer. From the moment of acceptance and delivery of the goods, the seller’s obligation to transfer the goods is considered fulfilled. The fact of acceptance of the goods by the Buyer is confirmed by a signature in the “Purchase and Sale Agreement” in the column “Acceptance and Transfer Certificate”. If the appearance or configuration of the goods does not correspond to the proper quality, the buyer has the right not to accept the goods and not to sign the documents.
Payment
Currently, the Ecolife online store offers following methods payment for orders:
- Payment in cash upon receipt
When an order is delivered, as well as when you receive the goods yourself at a pickup point, you can pay for the order in cash upon receipt. - Payment by bank transfer
Payment using the details to the company’s account upon filling out a receipt in the bank or via online banking. After placing an order, you will receive an invoice for payment and a receipt with our details. The prices indicated in the invoice are final and include VAT. The invoice issued is valid for 5 calendar days. This payment method can be used through any bank operating in Russia.
Note:
Banks charge a transfer fee Money. For information about the amount of the commission fee, check with the bank where you plan to pay the receipt. If you choose this payment method, please wait until you receive your invoice.
Power
- Thermal power 40 kW
- Efficiency at 30% power, up to 107,6 %
- Power consumption in DHW mode 41,2
- Min. consumed thermal power 5,9
- Max. useful warm heating power: in 50/30C mode 34.9 kW
- Power consumption 142 W
- Min. useful warm heating power: in 80/60C mode 5.7 kW
- Min. useful warm heating power: in 50/30C mode 6.3 kW
- Power consumption in heating mode 33 kW
Fuel consumption
- Consumption natural gas 4.36 m3/h
- Consumption liquefied gas 3.2 kg/h
- Min. water consumption in the DHW circuit 2
Pressure
- Nominal pressure natural gas 13-20 mbar
- Min. pressure in the DHW circuit 0,15
- Max. pressure in the DHW circuit 8
- Expansion tank pressure 0.8 MPa
Smoke removal
- Chimney diameter(60-100)/80 mm
Temperature
- Temperature adjustment range, C 35-60
Connection and installation
- Installation type: Wall mounted
Voltage and power supply
- Voltage 230 V
Dimensions and weight
- Height 763 mm
- Width 450 mm
- Depth 345 mm
- Weight 41 kg
- Package weight 44 kg
- Package size 90x39x54
Main characteristics
- Combustion chamber type Closed
- Efficiency 97.6%
- Fuel type Gas
- Number of circuits Dual-circuit
- The homeland of the brand is Italy
- Productivity at dT=35C 16.4 l/min
- Boiler type Condensation
- Productivity at dT=25C 22.9 l/min
- Expansion tank capacity 10 l
Product description
The models of the LUNA Duo-tec+ series have the ability of the boiler to adapt to the type and quality of gas, chimney parameters, chimney and other conditions. All models are equipped with a built-in two-speed pump, which is controlled by the boiler electronics and adapts to the heating system, ensuring optimal temperature regime and energy savings. The LUNA Duo-tec+ series boilers are equipped with a modern burner with complete pre-mixing of the gas-air mixture and operate with a power modulation ratio of 1:7.
GAS SYSTEM
- Adaptive combustion control system;
- Power modulation ratio - 1:7;
- Maintain rated power when inlet gas pressure drops to 5 mbar;
- Continuous electronic flame modulation in heating and domestic hot water modes;
- Reduced CO and NOx content;
- AISI 316L stainless steel burner with pre-mixing of gas and air;
- Can be reconfigured to run on liquefied gas.
HYDRAULIC SYSTEM
- Energy-saving two-speed circulation pump with electronic control and built-in automatic air vent;
- Primary heat exchanger made of AISI 316L stainless steel;
- Secondary plate heat exchanger made of stainless steel (double-circuit models);
- Automatic bypass;
- Pump post-circulation;
- Cold water inlet filter;
- Built-in electric three-way valve (including single-circuit models).
TEMPERATURE CONTROL
- New control panel with wide display;
- Two heating temperature sensors on the supply and return;
- Self-adaptation of weather-dependent automation;
- The temperature control range in the heating system is 25–80°C;
- Built-in weather-compensating automation;
- Regulation and automatic maintenance of the set temperature in heating and hot water circuits;
- Digital indication of temperature and pressure;
- Ability to control multi-temperature zone systems.
Gas condensing boiler Baxi LUNA Duo-tec 40 - double-circuit wall-mounted heating equipment
For heating and hot water supply in a private house, the Baksi Luna Duo Tek 40 wall mounted boiler is suitable - easy to use
All models are equipped with a built-in two-speed pump, which is controlled by the boiler electronics and adapts to the heating system, ensuring optimal temperature conditions and energy savings. The heating boilers are equipped with a modern burner with complete pre-mixing of the gas-air mixture and operate with a power modulation ratio of 1:7.
The models of the LUNA Duo-tec series have the ability of the boiler to adapt to the type and quality of gas, chimney and other conditions. All models are equipped with a built-in two-speed pump, which is controlled by the boiler electronics and adapts to the heating system, ensuring optimal temperature conditions and energy savings.
Specifications |
Unit Change |
Double-circuit boilers Baksi |
Baxi Luna Duo-tec 40 |
||
kW | 40 | |
kW | 32 | |
kW | 34,9 | |
kW | 5,7 | |
kW | 6,3 | |
kW | 41,2 | |
kW | 33 | |
kW | 5,9 | |
m 3 /h (kg/h) | 3,36 (3,20) | |
% | 97,6 | |
% | 105,8 | |
% | 107,6 | |
l/bar | 10/0,8 | |
°C | 35–60 | |
l/min | 22,9 | |
l/min | 16,4 | |
l/min | 2,0 | |
bar | 8/0,15 | |
mm | (60–100)/80 | |
m | 10/80 | |
mbar | 13–20 | |
W/V | 142/230 | |
dimensions |
||
- height | ||
- width | mm | 450 |
- depth | mm | 345 |
NET/GROSS weight |
kg | 41/44 |
Equipment Baxi (Baxi) LUNA Duo-tec 40
Heat exchanger made of stainless steel;Weather-compensated automation;
LCD display with indication of operating parameters;
Heating circuit frost protection;
Setting all parameters from the front panel of the boiler;
Security systems: overheating, flame, draft;
Energy-saving two-speed circulation pump with electronic control and built-in automatic air vent.
Gas system
- Adaptive combustion control system;
- Power modulation ratio - 1:7;
- Maintain rated power when inlet gas pressure drops to 5 mbar;
- Continuous electronic flame modulation in heating and domestic hot water modes;
- Reduced CO and NOx content;
- AISI 316L stainless steel burner with pre-mixing of gas and air;
- Can be reconfigured to run on liquefied gas.
Hydraulic system
- Energy-saving two-speed circulation pump with electronic control and built-in automatic air vent;
- Primary heat exchanger made of AISI 316L stainless steel;
- Secondary plate heat exchanger made of stainless steel (double-circuit models);
- Electric three-way valve (including single-circuit models);
- Automatic bypass;
- Pump post-circulation;
- Cold water inlet filter;
- Possibility of connecting external storage boiler For hot water.
Temperature control
- New control panel with wide display;
- Two heating temperature sensors on the supply and return;
- Self-adaptation of weather-dependent automation;
- Temperature control range in the heating system is 25-80°C;
- Built-in weather-compensating automation;
- Regulation and automatic maintenance of the set temperature in heating and hot water circuits;
- Digital indication of temperature and pressure;
- Ability to control multi-temperature zone systems.
Control and safety devices
- Electronic pressure gauge with burner shutdown function at pressure below 0.5 bar;
- Electronic self-diagnosis system and storage of the latest operating errors;
- Ionization flame control;
- Pump and three-way valve blockage protection systems;
- Protective thermostat against water overheating in the primary heat exchanger;
- Control of safe removal of combustion products using an NTC sensor;
- Safety valve in the heating circuit (3 atm.);
- Frost protection system in heating and hot water circuits.
Specifications |
Unit Change |
Single-circuit boilers Baksi |
Double-circuit boilers Baksi |
||||
Max. useful thermal power for DHW |
kW | - | - | - | 24 | 28 | 33 |
Max. useful warm heating power in 80/60°C mode |
kW | 12 | 24 | 28 | 20 | 24 | 28 |
Max. useful warm heating power in 50/30°C mode |
kW | 13,1 | 26,1 | 30,5 | 21,8 | 26,1 | 30,6 |
Min. useful warm heating power in 80/60°C mode |
kW | 2 | 3,4 | 4,0 | 3,4 | 3,8 | 4,7 |
Min. useful warm heating power in 50/30°C mode |
kW | 2,2 | 3,7 | 4,3 | 3,7 | 4,1 | 5,1 |
Max. consumed thermal power for DHW |
kW | - | - | - | 24,7 | 28,9 | 34 |
Max. consumed thermal power for heating |
kW | 12,4 | 24,7 | 28,9 | 20,6 | 24,7 | 28,9 |
Min. thermal power consumption |
kW | 2,1 | 4,1 | 4,8 | 4,1 | 4,8 | 5,7 |
Maximum consumption of natural (liquefied) gas | m 3 /h (kg/h) | 1,31 (0,96) | 2,61 (1,92) | 3,06 (2,25) | 2,61 (1,92) | 3,06 (2,25) | 3,60 (2,64) |
Max. productivity (efficiency) in 75/60°C mode |
% | 97,6 | 97,6 | 97,6 | 97,6 | 97,6 | 97,6 |
Max. productivity (efficiency) in 50/30°C mode |
% | 107,5 | 107,5 | 107,3 | 107,5 | 107,5 | 107,3 |
Max. performance (efficiency) at 30% load |
% | 107,8 | 107,6 | 107,6 | 107,6 | 107,6 | 107,7 |
Ext. capacity/fill pressure tank |
l/bar | 8/0,8 | 8/0,8 | 10/0,8 | 8/0,8 | 8/0,8 | 10/0,8 |
Temperature control range in the DHW circuit |
°C | - | - | - | 35–60 | 35–60 | 35–60 |
Hot water productivity at ΔТ=25°С |
l/min | - | - | - | 13,8 | 16,1 | 18,9 |
Hot water productivity at ΔТ=35°С |
l/min | - | - | - | 9,8 | 11,5 | 13,5 |
Min. water consumption in the DHW circuit |
l/min | - | - | - | 2,0 | 2,0 | 2,0 |
Max./min. pressure in the DHW circuit |
bar | - | - | - | 8/0,15 | 8/0,15 | 8/0,15 |
Diameter of the chimney. pipes (coaxial/separate) |
mm | (60–100)/80 | (60–100)/80 | (60–100)/80 | (60–100)/80 | (60–100)/80 | (60–100)/80 |
Max. chimney length. pipes (coaxial/separate) |
m | 10/80 | 10/80 | 10/80 | 10/80 | 10/80 | 10/80 |
Nominal gas inlet pressure (methane G20) |
mbar | 13–20 | 13–20 | 13–20 | 13–20 | 13–20 | 13–20 |
Electrical Power/Voltage |
W/V | 105/230 | 120/230 | 135/230 | 120/230 | 130/230 | 135/230 |
dimensions |
|||||||
- height | 763 | ||||||
- width | mm | 450 | 450 | 450 | 450 | 450 | 450 |
- depth | mm | 345 | 345 | 345 | 345 | 345 | 345 |
NET/GROSS weight |
kg | 34,5/37,5 | 34,5/37,5 | 36/39 | 38,5/41,5 | 38,5/41,5 | 39,5/42,5 |
Guarantee period Baxi LUNA Duo-tec is two years (24 months) from the date of putting the equipment into operation, but not more than 30 months from the date of sale of the equipment. Starting from the 14th month of operation, the warranty is valid only if there is a mark on the completion of service in the warranty card. Regular service Maintenance is carried out at the expense of the client, or is included in the cost of the equipment maintenance contract.
In the absence of appropriate documents, the warranty period is calculated from the date of manufacture of the equipment.
Warranty period for units and components replaced after expiration warranty period for equipment is 12 months. As a result of repair or replacement of units and components of the equipment, the warranty period for the equipment as a whole is not renewed.
The warranty is valid only when the product is put into operation (first start-up) by a specialized service organization that has licenses established by Russian legislation.
When selling a boiler, a trading company provides end users with the coordinates of service organizations. The service organization may be integral part trading company.
The end user is required to have a document confirming the commissioning of the product, for example, a completed recommended warranty card from BAXI S.p.A.. this document The following points must be indicated:
1) Device model
2) Serial number
3) Date of sale
4) Date of first start-up (product commissioning)
5) Name, address and telephone number of the service organization that carried out the first start-up (putting the product into operation)
6) Signature and surname of the technical specialist who performed the first launch.
If malfunctions occur during the warranty period, warranty work is performed by the organization that commissioned the product (in the absence of other warranty agreements). BAXI S.p.A. provides compensation for the cost of failed boiler components under warranty through official dealers BAXI S.p.A. In turn, official dealers of BAXI S.p.A. compensate the cost of these components to trading companies. To compensate for the cost of a failed component, the service organization must provide, along with the faulty components, a completed “individual repair report form” in the prescribed form or provide the same data in electronic form (using a template file from BAXI S.p.A.). Spare parts are purchased by trading companies or service organizations from official dealers of BAXI S.p.A. for products or spare parts.
Service organizations can enter into service contracts and thus become authorized service centers and authorized service partners of BAXI S.p.A.
BAXI Authorized Service Partners (ASPs) are organizations authorized to perform on behalf of BAXI S.p.A. first launch and service maintenance BAXI equipment.
Authorized service centers BAXI (ASC) are organizations authorized to carry out on behalf of BAXI S.p.A. first start-up and service maintenance of BAXI equipment and taking on the following additional obligations:
-
when contacting, perform the first start-up and carry out subsequent warranty and service maintenance of any BAXI equipment purchased in any trade organization or established by another organization;
-
sell BAXI spare parts to all applicants.
Authorized service centers and service partners of BAXI in agreement with the representative office of BAXI S.p.A. have the right to increase the warranty period. Also BAXI S.p.A. at warranty repairs, in addition to compensation for spare parts, pays the cost of travel and work (according to the contract). Compensation under warranty BAXI S.p.A. carried out through official BAXI dealers, or through direct payments.
Authorized service centers and service partners of BAXI are created either on the basis of trading companies that regularly work with BAXI products, or on the recommendation of these trading companies.
Full information:
Specifications:
- Max. useful thermal power for DHW: 40 kW
- Max. useful warm heating power in 80/60°C mode: 32 kW
- Max. useful warm heating power in 50/30°C mode: 34.9 kW
- Max. consumed thermal power for hot water supply: 41.2 kW
- Max. consumed thermal power for heating: 33 kW
- Max. natural/liquefied gas consumption: 3.36 m3/h (3.20 kg/h)
- Max. productivity (efficiency) in 75/60°C mode: 97.6%
- Max. productivity (efficiency) in 50/30°C mode: 107.3%
- Max. performance (efficiency) at 30% load: 107.7%
- Ext. capacity/fill pressure tank: 10 l / 0.8 bar
- Temperature control range in the DHW circuit: 35-60 °C
- Hot water productivity at Δt=25°С: 22.9 l/min
- Hot water productivity at Δt=35°С: 16.4 l/min
- Min. water flow in the DHW circuit: 2 l/min
- Max./min. pressure in the DHW circuit: 8/0.15 bar
- Diameter of the chimney. pipes (coaxial/separate): (60-100)/80 mm
- Max. chimney length. pipes (coaxial/separate): 10/80 m
- Nominal natural gas inlet pressure: 13-20 mbar
- Electrical power/voltage: 142 W / 230 V
- Dimensions (HxWxD): 763 x 450 x 345 mm
- Weight: 41 kg
Gas system:
- Adaptive Combustion Control System
- Power modulation ratio - 1:7
- Retains rated power when input gas pressure drops to 5 mbar
- Continuous electronic flame modulation in heating and domestic hot water modes
- Reduced CO and NOx content
- Burner made of stainless steel AISI 316L with pre-mixing of gas and air
- Can be reconfigured to run on liquefied gas
Hydraulic system:
- Energy-saving two-speed circulation pump with electronic control and built-in automatic air vent;
- Primary heat exchanger made of AISI 316L stainless steel;
- Secondary plate heat exchanger made of stainless steel (double-circuit models);
- Electric three-way valve (including single-circuit models);
- Automatic bypass;
- Pump post-circulation;
- Cold water inlet filter;
- Possibility of connecting an external storage boiler for hot water.
Temperature control:
- New control panel with wide display
- Two heating temperature sensors on supply and return
- Self-adaptation of weather-dependent automation
- Temperature control range in the heating system 25-80°C
- Built-in weather-compensating automation
- Regulation and automatic maintenance of the set temperature in heating and hot water circuits
- Digital temperature and pressure display
- Ability to control multi-temperature zone systems
Control and safety devices:
- Electronic pressure gauge with burner shutdown function at pressure below 0.5 bar
- Electronic self-diagnosis system and storage of the latest operating errors
- Ionization flame control
- Pump and 3-way valve blockage protection systems
- Safety thermostat against water overheating in the primary heat exchanger
- Monitoring the safe removal of combustion products using an NTC sensor
- Safety valve in the heating circuit (3 atm.)
- Frost protection system for heating and hot water circuits