home · Networks · How to make a small crossbow out of paper. How to make a crossbow out of paper? DIY paper crossbow. Preparation of material, or How to make a crossbow from wood

How to make a small crossbow out of paper. How to make a crossbow out of paper? DIY paper crossbow. Preparation of material, or How to make a crossbow from wood

There is, perhaps, no other creative material as amazing in its versatility as ordinary paper. Under with skillful hands from a sheet of office paper, anything your heart desires can come into being - a craft, and even a model of a crossbow. Yes, not simple, but very effective. How to make a crossbow from ordinary office paper with your own hands will be discussed in our master class.

MK Crossbow made of paper

  1. Let's start building a crossbow with a bowstring. For this we will take three thin elastic bands.
  2. We pass one elastic band through the other, tightening the resulting knot tightly.
  3. We will repeat the same with the third elastic band, thus forming a chain 23-25 ​​cm long.
  4. Take a sheet of regular A4 office paper and roll it into a tube along the long side.
  5. Secure the end of the tube with tape.
  6. Let's fix the other end of the tube in the same way, making sure that it doesn't unwind.
  7. Let's roll up a few more paper tubes in the same way.
  8. We will also securely secure the ends of these tubes with tape.
  9. Cut one of the tubes into two equal parts.
  10. Connect the two tubes together at right angles, placing one in the center of the other.
  11. Let's strengthen the horizontal tube-base by attaching another one to it.
  12. We will not spare the adhesive tape and securely fasten the entire structure together.
  13. Take a tube cut into two parts.
  14. We attach one of its halves at an angle to the crossbar so that it forms a stop.
  15. We will also attach the second half of the tube to the transverse bar on the other side.
  16. We roll up another tube.
  17. We separate from it a segment equal to 1/3 of its length.
  18. We wind this section to the crossbow so that it reaches the intersection of the vertical tube with the side stops. We wind the remaining section of the tube to vertical support at right angles, forming a handle.
  19. We wrap another paper tube at a right angle at the top of the crossbow.
  20. We tighten the bowstring, securing it at both ends of the crossbar.
  21. We strengthen the middle part of the bowstring with several layers of tape.

A copy of an ancient crossbow is very interesting thing as per plan appearance, and when shooting from it. Now let's talk about how to make a crossbow at home so that it really looks like ancient weapons. Nowadays, there are many modern crossbows, but their cost is quite high, and you want to hang a working copy of an ancient crossbow on the wall in your bedroom.

Now let’s look step by step at what is needed to create a wooden crossbow. Few tools are needed.

  1. Well sharpened knife.
  2. Drill.
  3. Hacksaw for metal.

Preparation of material, or How to make a crossbow from wood

In order for the product to look and shoot like a real weapon, it must be made from suitable wood:

  1. Poplars.
  2. Ash.
  3. Pines.
  4. Duba.
  5. Maple.
  6. Acacias.

These trees are perfect.

A crossbow consists of two main parts - the bow and the stock. If we are making a weapon with a power of up to 20 kilograms, for the bow we need to find an even branch five centimeters thick and a meter long. If the power of the crossbow is planned to be more than 20 kilograms, then it is better to take a blank 10 centimeters thick and a meter long. For the crossbow stock, select a branch with a diameter slightly thicker than the bow blank. If there are branches on the sawn material, under no circumstances should they be completely cut off. You just need to shorten them so that the length is from three to five centimeters. If you cut off the knots completely, they will immediately crack and the workpiece will be damaged.

Drying harvested wood

Before making a crossbow with your own hands, you need to ensure that the material dries gradually. To do this, you need to cover the cuts with varnish so that moisture does not escape through them too quickly. We also cover the cuts on the knots. If this is not done, then due to rapid evaporation the wood will crack, and this is undesirable. After this, the blanks should lie for a month in a dry and dark place. How longer tree If it dries, the better.

Primary processing

The material is ready, we can start. Let's start with the onion. We examine the annual rings of the tree. Where they are thinner, the northern side, that’s what we need. In this place the structure of the material is much denser. Now you need to cut the workpiece in half and take the north side for the product. After everything is done, the tree needs to be allowed to lie for another week so that the remaining moisture comes out.

Making a crossbow bow

We begin making a bow, during which we will see the structure of the tree and learn how to make a crossbow at home using ancient technologies. So, let's get started, we need to cut off the layers of the tree where its core is present. If you leave it, there is a risk that longitudinal cracks will appear. Then we measure the middle of the bow and begin to cut off the excess material, making the bow. When processing, you must ensure that its shoulders are the same. We check for bending all the time. As soon as the shoulders begin to bend even a little, you need to make a test bowstring.

A test string is a strong rope with one loop on one side and several on the other, located at different distances. They are needed to measure the bend of the bow arms. The more material is cut, the more they can be bent, while changing the loops to closer ones. By constantly pulling the test string, it is easy to see whether the bend is uniform after processing the bow. After all, if you look only visually, you can make a big mistake. The density of wood is not the same in all places, so a seemingly perfect bow may bend unevenly. Sometimes it happens that a thick section is a weak point, and a thinner section, on the contrary, does not bend. To avoid mistakes, you need to constantly check the onion. Only after studying all the nuances can you make a working copy, understanding how to make a crossbow with your own hands, and fully display the power and beauty of the ancient weapon.

Making a crossbow stock

In the front part of the stock you need to cut a two-centimeter depression where the bow will be located. After we mark 30 cm from the edge, the bowstring and arrow will walk on this surface. We level this plane if there are bends or branches on it. Afterwards you need to measure out a place for a gutter 1 cm thick and 0.5 cm deep, then cut out the holes for the bow and trigger. It is better to do this with a chisel or a carpenter's cutter, but to understand in detail how to make a crossbow, the drawings will help.

Trigger

Let's take the simplest hold, called a nut. This is a cylinder that rotates freely on an axis. On one side there are hooks for the bowstring, on the other there is a stop for the L-shaped trigger. If the crossbow has a draw weight of up to 30 kg, the trigger can be made of wood. However, if the power is greater, it should be made of metal.

Making a bowstring

You need to take a board and insert pegs 1 cm thick. They should protrude 3 cm. From one to the other, we wind a nylon thread in a circle. When the thickness of all the threads is approximately 5 mm, you need, without removing them from the pegs, to wrap this skein once in a circle so that all the threads are tightly wound. After this, near the peg, we collect the two halves of the bowstring with our fingers and wrap it again, but much tighter, until the next peg. So, we will get a bowstring with two loops. A diagram on how to make a crossbow will help you understand everything. Everything is very clear on it.

Assembling the crossbow and pulling the string

First you need to attach the bow to the stock, then we mount the trigger mechanism, after which we tighten the bowstring. You can’t just tighten it, so you need to use a trial one. Next you need to draw the crossbow. When the bow is bent, we hang the bowstring. After which the trial is removed. That's it, the ancient weapon is ready. Here's how to make a crossbow at home using only basic tools.

Making a toy mini crossbow

For fun at home with children or for fooling around with friends, you can make a mini crossbow from scrap materials. What you will need for this:

  1. Two wooden skewers.
  2. Carpenter's chisel or knife.
  3. Scotch.
  4. Wooden clothespin.
  5. Glazing bead.

Scheme, or How to make a mini-crossbow from what you can easily find at home

  1. We take wooden skewers and cut off the sharp ends from them. After that we tie them together at the edges. This will be the crossbow bow.
  2. We take a glazing bead and mark two segments on it equal to the length of the bow of our miniature weapon. Then we cut off these two parts and connect them together with tape. This is the crossbow stock. We tape the onion in front with tape.
  3. After this, we pull the bowstring onto the crossbow.
  4. We pull it back and see at what distance to install the hook. They will use a clothespin, or rather, its spring and one half of the wooden part.
  5. We cut out the necessary grooves on the crossbow stock so that it replaces the missing part of the clothespin. Let's assemble our hook.
  6. The crossbow is ready, press the clothespin on top, thereby opening it, pull the string together with the arrow and clamp it. To shoot, press from above again.

We figured out how to make a mini crossbow, and now we can go further and create a weapon out of pencils.

Create a crossbow from pencils

To do this you need to take:

  1. Four pencils.
  2. Seven rubber bands.
  3. Ballpoint pen body.
  4. Scotch.

Shall we get started?

  1. First you need to take pencils and connect them two at a time. You can use rubber bands or tape. This will be the bow and crossbow stock.
  2. In the front part of the bed we wrap the bow from below.
  3. On top of the stock we tape the body from the handle, this will be a guide for the arrow. It can be made from the shaft of the same pen.
  4. Now we put one elastic band on the ends of the bow, and tie their edges with thread or tape to make a solid bowstring. Now we grab the bowstring with the inserted arrow, launch it into the guide from the handle body and release it.

Here's how to make a crossbow out of pencils that shoots great.

Let's start creating a paper crossbow

This requires:

  1. A4 sheets - 9 pieces.
  2. Popsicle sticks - 4 pieces.
  3. Scotch.
  4. Durable nylon thread.

How to make a crossbow out of paper that will shoot pencils?

  1. Place three sheets of paper lengthwise in front of you. We bend from left to right. Cut in half along the bend line. It turns out six sheets, the width of which is 10.5 cm and the length of 29.7 cm. We divide them into two piles of three sheets each.
  2. Using a pencil, we twist one and then the second stack of sheets into tubes. Their length should be 10.5 cm, and their diameter should be slightly thicker than a pencil. To prevent them from unwinding, we secure them with tape.
  3. We insert a popsicle stick into one end of the tubes a third of their length. We break off the protruding part. From the free side we insert a whole popsicle stick, also a third. These are the arms of the bow. Now you need to bend them in half in the center of the paper tubes.
  4. We take five more sheets of paper, twist them with a pencil, this will be the crossbow stock.
  5. We tie the arms of the bow to the resulting tube in front. They need to be evenly wound in front of the product bed. Here's how to make a crossbow at home from paper. Now he needs a hook, a trigger and a guide.
  6. We tie the thread to the arms of the bow and pull it to understand where the hook will be. Having decided, we cut through the bed in this place. Then we cut off a piece of stick 3-4 cm in size and insert it into the hole so that it protrudes 5 mm from above and acts as a trigger from below.
  7. And the final touch. We make a tube 3 cm long so that a pencil can pass through it freely, and tape it to the front of the crossbow above its bow. This is a guide for the stele. That's it, now you can tighten the bowstring, put, for example, a pencil in the guide and shoot.

Here we looked at creating a copy of an ancient crossbow. However, it was also interesting to create throwing weapons from scrap materials, as they say: on your knees. From paper, they even showed how to make a crossbow from pencils, and a mini-weapon that turned out to be quite powerful for its size. So you should look at the world more broadly and always improvise, this is the only way to achieve excellent results in deeds worthy of admiration by those around him.

Make a crossbow with my own hands, You will not regret!

You will need

  • - boards;
  • - carpentry tools;
  • - hemp rope;
  • - feathers:
  • - leather;
  • - iron wire.

Instructions

The crossbow consists of three parts. This is a stock, an arc and a trigger mechanism, aka . To make a crossbow of the most ancient design, start with an arc. The parameters of the remaining parts depend on it. Select boards. Suitable for the arc are yew, hazel, and rowan. Conifers are not suitable. The board must be well dried and seasoned. There should be no curling, cross-layering or knots. Cut a piece 70-80 cm long, 3-4 cm wide and about 2 cm thick. Process it with a plane so that the arc evenly thins towards the ends to a width of 1-1.5 cm.

Make a bed. It is made from wood hardwood having sufficient It can be maple, beech and even oak. Keep in mind that the crossbow was not pressed down when firing and did not have a butt. Therefore, make the bed in the form of a board that is comfortable to hold in your hands. In the front of the stock, make a groove into which the central part of the arc should fit.

At a distance of 8-10 cm from the groove, make a hole for the rope fastening of the arc. Temporarily secure the bow in the slot with rope by wrapping the rope around the bow and threading it through the hole in the stock. Attach a bowstring to the ends of the soul. To do this, you need to make small cuts on it with a knife. Tension the bowstring as you would during shooting (as much as your strength and arc strength allow). Make a mark on the stock in the place where the drawn bowstring is located at this moment. Remove the arc from the bed and continue processing it. From the bowstring mark, step back a distance equal to the length of your forearm. Saw off the workpiece.

Make a trigger mechanism. In this design, you can use the most ancient lock of the so-called pin type. Drill through hole in the stock where the bowstring is marked. In the upper part of the stock, make a transverse recess to the depth of the bowstring. At the bottom, fasten it to the hinge according to the drawing. The lever axis can also be made of wood and fixed with two pieces of wire passing through it. Insert the axle into the stock, thereby securing the lever. Secure it by piercing it on both sides with pieces of wire. Holes for the wire can be drilled or burned. The latter method is more consistent with historical technology. Wrap the protruding small ends of the wire around the axis.

Place the stock and lever together. Secure them in this position with a clamp or rope and, using a ready-made hole in the stock, drill a blind recess in the lever to a depth of 1.5-2 cm. Remove the clamp. Check how freely the lever moves on the axle. Friction should be minimal.

Using a knife, cut a round pin from oak or beech so that its diameter is slightly smaller than the lock hole. The pin should fit freely into the hole, without friction or snags, resting on the trigger lever. The length of the pin should be such that when the lever is fully raised, the upper edge is level or slightly above the upper plane of the stock. The function of the pin is to push the string out of the groove.

Make a groove for the bolt (arrow). Cut it from the front edge of the stock to the top hole of the lock. The depth of the groove should not exceed a quarter of the diameter of the bolt.

Swipe final processing wooden parts. Sand them down using sandpaper. You can coat them with albumin varnish ( egg white, dissolved in water) or wax.

Use a rope to secure the bow to the stock. Check that the lock is working correctly. When the lever is tilted upward, the pin should confidently push out the bowstring.

To make a homemade crossbow you will need:
*A block of non-resinous wood, size 700x10x40 mm.
*The second leaf of the spring of the Moskvich car.
*Profile pipe 50x50x2 mm. 10 cm long.
*Profile pipe 15x15x1.5 mm.
*Small segment sheet metal 2 mm.
*Stainless steel metal 4 mm thick. and 0.5-1 mm. (for the descender).
*Steel corner 50x50x4 mm. 35 cm long.
*Rod D=8 mm. 40 cm long.
*Bolts with nuts D=8
*Stainless steel molding from VAZ-2106 door 2 pcs.
*Metal rollers 2 pcs., glass lifting mechanism from the door of a VAZ car.
*Cable D=3 mm. 3 m long, two terminal loops.
*Epoxy resin, wood stain, wood varnish for exterior use.
*Two small springs (working in tension).
*A dozen nails for roofing felt, one two hundred nail, tube D=6 mm, small washers.

We will use the following tools:
*Welding machine.
*Hand-held circular saw.
*Electric drill with speed control, carbide drills for metal D=3, 5, 8, 10 mm.
*Bulgarian, cutting discs for metal, grinding discs for wood.
*Keys, pliers, screwdriver, vice, narrow chisel, knife.
*File, sandpaper.
*Safety glasses.

Point 1. Making a stock.

Take a well-dried wooden block, I had one made of birch, let's sketch out a sketch of the bed on it. We customize the size of the butt for each individual (according to your height), and the stock depending on the length of the arrows you will use. I use 440 mm arrows, but I had to save money on the stock, leaving only 300 mm, so in total total length It turned out to be 740 mm, I didn’t dare to do any more.


Let's draw a marking for the guide sample, for the arrow fletching, width 5 mm, depth 10 mm.

Using a circular saw, we cut out the groove the entire length, to the end of the trigger (lock).

It should look something like this.

Using a drill D=12 mm. select the cavity under descender, level the ledges with a chisel and knife. We drill a hole for the trigger, bore it with a chisel and knife.

Point 2. Making a lock or release device.

Let's take the "walnut" type as the basis for the lock. To prevent anything from rusting, we will use stainless steel, take a sheet 4-5 mm thick, if you can’t find one, make it a composite of several sheets glued together and taken with rivets. Draw the shape of the parts on the metal.



Using a cutting disc and a grinder, we cut out the workpiece according to the markings.

In the center of the “nut” we drill a hole for the axis of rotation, D = 6 mm.

We process all sides with a file.

We sand with sandpaper, achieving a completely smooth surface.

It should look something like this.

We grind out the remaining elements of the lock, the sear.

I lengthen the trigger with two thin sheets of stainless steel and secure it with homemade rivets.

On the grinding machine we achieve the desired shape blanks

We make the housing of the trigger mechanism from a thin sheet of metal.

We drill three holes D = 2.5 mm in the body of the sear, one for the fastening axis and two for fastening the springs.



Let's attach the trigger spring into place.



Let's see on the table how the parts become in the cocked state.

And like after the shot.

Let's place one side of the case on the inside of the mechanism and drill holes in place for all the axes.

From a two hundred nail, 6 mm in diameter, we will make an axis for the “nut”.

Saw off the sharp end of the nail.

We measure the length of the future axis and saw it off.



Using thin nails for roofing felt, we will make the remaining rivet axles. Use a grinder to remove the shimmer on the nail heads.

Now they will fit well to the body.

Let's install the sear on the axle in the body, use intermediate washers.



We saw off the excess length of the nail, leaving 1 mm. on both sides for rolling.

Using an anvil, hammer the end of the axle.

We drill a hole for the axle with a spacer to attach the sear spring.

From a suitable tube we cut off a spacer sleeve for this axis.

We move one side of the body to the side.

We install the axle, bushing and engage the spring.

We assemble the body halves together.

We saw off the excess length, leaving a protrusion of 1 mm. under the hammer.

Let's roll it.

Now you can install the largest rivet axle of the lock. Aligning the holes.

Let's take the previously measured and sawed-off axis D=6 mm, and immediately tap it a little with a hammer on one side.

We install it in place.

And we’ll also roll it, the main thing is not to overdo it, so as not to jam the moving mechanism inside.

Point 3. Installation of the lock mechanism in the stock.



If something prevents the lock from sitting well in place, we modify it with a chisel or knife. After installation, check how the trigger moves.

If everything is fine, you can drill holes for the mounting screws and screw them into place.





Now we need decorations from the door of the VAZ-2006, they are also made of stainless steel, which is very good. To give them additional rigidity, they were filled with epoxy resin.

After complete hardening, in a day, we will drill four holes D = 3 mm in each for fastening screws.

Using a large drill, we will make hidden places for the heads of the screws so that the bowstring cable does not get caught when it slides along it.

We polish the hole exits with fine sandpaper to remove all burrs that damage the cable.

We install the finished guides on the bed.

We make sure that the screws do not go through in thin places.

We check that the lock moves without snagging on the guides.



Point 5. Making an arc or shoulders.

From the same donor doors, using a grinder, we extract the rollers of the glass lifting mechanism.

From these we will make blocks for the shoulders, and the arch itself from the second leaf of a spring from an old Moskvich car.

We will make pads to attach the spring to the stock.
To do this, from a 50x50 mm corner. Let's cut out the component elements to assemble them using welding, like this mount (block).

We will process the welds with a grinder. Let's drill mounting holes D=10 mm. under the bolts.

Based on the finished sample and the dimensions of the resulting block, we make grooves for mounting in the stock. We try on the fit, achieve a tight fit and fastening. According to the calculated position of the future bowstring, we outline and make a through groove in the sidewall of the stock, 70 mm long. 10 mm wide, the lower bowstrings will go here.

We bend and weld the leg bracket (stirrup).



Ears for blocks.
From profile pipe 50x50 we will make eyes for attaching the roller blocks to the arc (spring).

The most difficult thing in making the arc itself from a spring at home is drilling holes in it. It is necessary to drill with a drill at low speeds so that the drill does not burn, and constantly use water. If possible, drill with drills of different diameters, from thin to thick in increments of 0.5-1 mm, and constantly sharpen the tool.

We fasten the brackets with short M8 bolts and grind off the caps.

We attach the spring to the block with two M8 bolts, followed by a small weld along the edge of the fastening.





Now you need to open the bed with varnish and dry it.
We install the block with an arc on the stock, hammer down the metal-wood for a tight fit.

Insert and tighten the M8 bolts.



From long M10 bolts we will make axle bolts reduced in length with a short thread for blocks.

Let's take a tube from the anchor and use it to make spacer bushings for the block axes.

Let's drill holes D=10 mm in the ears. to install blocks. We install rigid loop ends on the cable.

We install a block with a cable on one side of the shoulder. Do not tighten the nut too much, so as not to jam the rotation of the roller.

Drill a hole in the nut and bolt for the stud.



We install the stud and press it with the nut in the direction of unscrewing.



We push the cable through the hole in the stock and do the same with installing the roller on the other side of the shoulder.

Point 6. Top part castle

From a profile pipe 15x15 mm. saw off two 120 mm sections. Using a grinder, we cut out two (L) shaped blanks from sheet metal, one rectangular plate (on the top) and a triangle (on the back).

We connect all the parts together by welding, and clean the welding seams with a grinding disc to make it look like a solid part.

From an old folding steel meter, we make an elastic boom holder.

The photo shows the mounting bolts for the rack for the optical sight.

The same thing, only the bolts also clamp the boom holder.

The sight rail itself (dovetail) is made of the same 2 mm sheet metal, with the sides ground off for mounting optics.

A square pad is visible along the optic rail to raise the rear and thereby tilt the scope down for correct aiming at targets beyond 25 m.

We install the lock bracket on the stock and drill holes for fastening, self-tapping screws and an M6 bolt.



We tighten the small screws so that they do not go into the arrow feather channel.

We tighten the back screw.

Additionally, we drill a hole and install the last bolt.







We install an optical sight.







Modern children most They spend their free time on a computer, tablet or smartphone. They no longer play on the street as before, do not use their imagination, do not invent something unusual. Naturally, times change, generations too, so don’t be too upset, because this is a natural process.

But here's your chance to give your child the opportunity to learn how to make things with their hands while providing them with new toys. For example, you can show him how to make a crossbow out of paper.

The benefits of classes for a child

Many parents may be indignant, because making something with their own hands is no longer relevant, it will only take up the child’s time, and will also take away precious minutes from the parents, because such an activity still needs to be taught, helped, and evaluated. But you don’t have to worry - naturally, there are crafts that can take hours and even days to make, but no one is forcing you to choose them. In order to teach your son or daughter how to make a crossbow out of paper, you will need a maximum of half an hour, but then the child will have a full-fledged toy and a lot of joy from the realization that he made it himself. You can use this when you want to take a little break from your baby, who constantly demands your attention - provide him with the material, and he will selflessly immerse himself in the manufacturing process, and then come running to you with a beaming face, demonstrating the result. So don’t underestimate the benefits of such an activity - in any case, no one is stopping you from trying.

And for testing, creating a crossbow is ideal.

What will you need?

If you are interested in how to make a crossbow out of paper, then first of all you need to decide what you need to make it. Naturally, the main component is paper; you will need at least 10 sheets of it, preferably in A4 format, since it will be much easier to make a crossbow from them. They are also the most accessible, so you shouldn’t have any problems finding this material. But how to make a crossbow out of paper without holding it together? To carry out the fastening you will need regular tape, which is also very easy to get. Another required element- this is a pencil that will play the role of an arrow loaded into a crossbow. You will need to use string as a bowstring, but you will need to make sure that it is thick and strong enough. To give the parts the desired shape, you will need scissors, and to make the process more fun, you should get some ice cream. But when you eat it, don’t rush to throw away the remaining wooden sticks - they will come in handy to create a full-fledged crossbow from paper and pencil.

These are all the components you will need - as you can see, there is nothing supernatural here, all the components can be found either at home, or bought at the nearest store.

Creating Crossbow Shoulders

In order to make from paper, you will need to go through three stages, and the first of them is making the shoulders. To begin, you will need four sheets of paper, which you need to fold in half lengthwise and cut along the fold line. After this, take the resulting small sheets and roll them into a tube, using a pencil if necessary. Once the tube is ready, secure its edges with tape to prevent it from unraveling, then repeat the procedure with the remaining half of the small sheets. But this is just the beginning - to give the crossbow's arms strength, you will need to place paper straws Popsicle sticks. On one side, measure four centimeters on the tube and on the stick, insert the stick to the mark and break it so that it remains inside the tube. After this, bend the tube and insert another stick from the other end, and then repeat the procedure with the other shoulder. To make a crossbow made of paper and pencil more reliable, secure the entire result with tape.

Stage two: creating the foundation

Once the arms are ready, you can move on to creating the base of the crossbow, which is also called the stock because it is where the arrows are placed.

To do this, you will need five sheets of paper, which you again fold, using a pencil for better effect, and secure with tape. From the edge where the shoulders will be attached, this tube needs to be made flattened - they will be adjacent to these flattened areas. And again, attach everything very securely, using tape, so that your crossbow does not fall apart, but serves for a long time and is reliable. Here you can also use part of the remaining sheet to make a small tube-sight, which will be slightly larger in diameter than a pencil - the arrow will pass through it when released. Use the remaining paper to make two small tubes at the base of the crossbow - the arrow will go there.

Trigger Installation

But a crossbow differs from a bow in that it has trigger, which automatically releases the string and sends the arrow into free flight. To make it, you will first need to attach a thread to the edges of the crossbow's arms. Then pull it all the way and in the place that comes into contact with the base of the crossbow, make a small hole, and at the bottom it should be slightly wider than at the top. This is where the trigger will be located, which you can make from an unused leftover popsicle stick.

The result is a completely working trigger mechanism that can be used to launch arrows. Before completing the work, check all the elements of the crossbow for secure fastening, and if something somewhere seems shaky to you, do not skimp on tape to secure this part properly.

Safety first

So, you have learned a crossbow that can fire pencil shots. Of course, this is not a real weapon, but if not handled carefully, it can also cause harm to your child's health and damage to your property. Therefore, your child should be taught not only how to make a crossbow, but also how to handle it. Demonstrate everything to him clearly, designate an area where he can play with the crossbow, and then he will be absolutely safe.