Adjustment of a plastic entrance door with three hinges. Methods for adjusting plastic doors. Basic functions of door adjustment keys

Before installing a plastic door, you must not only choose the manufacturer carefully, but also pay attention to its components. Only in these cases will the door serve you for decades. But some time after installation, the door mechanisms may fail. To eliminate this malfunction, it is not at all necessary to contact the specialists. You can adjust the mechanisms yourself. To do this, you need to know how to adjust it yourself.

The most common causes of breakdowns

As a rule, all malfunctions of plastic doors arise as a result of a violation of the position of the leaf itself. Due to its frequent use, all moving mechanisms gradually fail. Therefore, before adjusting the plastic door, let's first figure out in what cases it is necessary to do this.

• The bottom of the door rubs against the threshold. As a rule, this happens due to the mechanisms not being clamped tightly enough. This is not explained by the quality of the door itself, but by the carelessness of the technician who installed it. In addition, the door leaf can sag under its own weight. This is mainly due to weighted
• The middle part of the door (near the handle) rubs against the plastic door. This usually occurs as a result of sudden changes in temperature.
• The door does not close tightly. The cause of such a malfunction can be not only the same sudden changes in temperature, but also the displacement of the pressure roller after using the doors for a long time.

Prevention of problems with plastic doors

Many people probably think that, knowing how to adjust a plastic door, it is not at all necessary to treat it with care. But, unfortunately, this is not the case. The door can be adjusted several times. But after a while there will come a time when this procedure simply won’t help. Thus, you should always remember that the prevention of doors should also be taken seriously, as well as their selection or installation.

So, before purchasing this or that door model, never refuse its configuration, even if this increases the cost of your purchase. Otherwise, before you adjust the hinges of plastic doors yourself, you will again need to spend time and money finding one or another component.

Necessary accessories for plastic doors

The most important tools for adjusting plastic doors are considered to be the following:

1. Microlift. This device will help troubleshoot doors of any size and weight. It helps prevent even the heaviest door panels from sagging. The microlift takes on part of the door's load, but only in its closed position. It may look different. Its most common types are a roller at the bottom or a movable plate at the top of the blade.
2. Door opening limiter. This mechanism not only helps prevent the door from sagging, but also sets the maximum angle of its opening in such a way that it protects the door from impacts on the slopes.

In addition, before you choose a particular plastic door manufacturer, find out more information about it. The fact is that many companies neglect the quality of the fittings themselves and install cheaper ones, which may also be one of the reasons for the minimum service life of the product.

Elimination of sagging door leaf

We have already found out what the sagging of the leaf depends on, now let's look at how to properly adjust a plastic door with your own hands in this situation.

If you notice that the canvas is clinging to the threshold, you need to fix this problem as quickly as possible. To do this, open the doors and look for a small screw on the top hinge. As a rule, it is a hexagon. In some cases, it may look like an asterisk. In one case or another, you will need to select a key for the screw.

So, turn the screw clockwise. Make two or three turns. Close the door. It should now close freely.

If the canvas sag very much, and these actions did not help eliminate this malfunction, then experts give the following recommendation on how to adjust the plastic door in height. Locate the adjusting screw under the lower canopy protective cap and turn it clockwise a couple of times. These steps will help you solve your door sagging problem.

Elimination of rubbing of the door leaf on the side

Rubbing on the side of the door is also easy to prevent. How to adjust the plastic door in this case? To do this, find another screw on the lower canopy, which is located not from the bottom, but from the side, that is, from the inside of the canvas. Again, by twisting it clockwise, you can put the door leaf in the right place. It will no longer cling to the jamb and will be able to close easily.

If this technique does not help eliminate the rubbing of the door on the side, find the upper canopy, which was described above, and perform all the same steps.

Improving door sealing

If you notice that your door does not close tightly, then this troubleshooting item is for you. Let's figure out how to adjust the pressure of a plastic door.

To begin, remove the ends of the door. There are special eccentrics there. By rotating them you can set the correct door mode. The only difficulty here is finding the right eccentrics. Usually they are installed in threes at the top, side and bottom. They should all be gradually turned at the same angle so that the door closes tightly. But since this fit will only be near the handle, it will also be necessary to adjust the canopies with special screws.

Door handle adjustment

We have already looked at how to adjust a plastic door. But what to do if its handle does not function properly when opening? Don’t worry, you can also fix such problems with the handle yourself.

To do this, move the decorative plate 90 degrees. Underneath you will find the handle mechanism and mounting screws. Tighten these screws and the handle on the door leaf will be fixed more firmly. Thus, you will be able to regulate its tightness yourself, which makes it possible to troubleshoot the door lock opening mechanism.

Replacing handles on plastic doors

Now you know how to adjust a plastic door with your own hands. But replacing its handle will cause more difficulties. After all, such fittings are the most vulnerable. It is also worth noting that its service life is much shorter than indicated by the manufacturer.

The main reason why plastic door handles break is the poor quality of the material. Its constant use will lead to cracks, and in the future - to the fact that the handle breaks off completely.

If you are faced with the latter problem, first you need to select an analogue of your pen. You need to choose this or that fitting carefully, paying special attention to the identical dimensions of the part itself and the fasteners. As a rule, all these devices are practically the same, but in this case it would be useful to play it safe.

The handle is attached directly to the metal base hidden under the plastic profile with self-tapping screws, which are subsequently closed with decorative plugs.

We hope our tips helped. Now you know how to adjust the plastic entrance door yourself.

The door serves to delimit space in an apartment or house and protects residents from street noise and winter cold. Many people install plastic structures in their apartments: they look good and have many other advantages. But they also have a drawback - the heavy weight of the doors. It leads to sagging and loss of tightness. To troubleshoot problems, there are instructions for adjusting plastic doors yourself.

Problems most often arise with the onset of autumn. The plastic sheet begins to close poorly, touches the frame, and requires additional effort when turning the handle. As a result, cold outside air may enter the room. To eliminate these problems, plastic doors are adjusted, which can be done on your own.

If a plastic product is under warranty, it is better to call a specialist. He can check the entire door structure and determine the cause of the problems. After this, he will carry out work on lubricating the parts and making the necessary adjustments to the plastic door.

The adjustment may involve adjusting the plastic product horizontally and vertically, as well as adjusting the pressure of the canvas to the box. The door will acquire the qualities of a newly assembled structure: it will have a tight seal against the frame and will not close or open arbitrarily.

Prevention

PVC doors will have to be adjusted annually. To do this less often, you need to follow some simple rules of prevention. It is good to equip the doors with an opening limiter and a microlift. The microlift will protect the canvas from sagging, and the limiter will not allow the hinges to become loose when the doors are fully opened.

To prevent the handle from breaking, do not hang heavy bags on it. Plastic parts will remain intact longer if you wipe them with a clean, damp cloth. Any plastic door structure includes rubber seals. They must be regularly lubricated with silicone compounds, which impart plasticity to the rubber.

The lock, eccentrics and other parts of the mechanism are also subject to lubrication. Over time, the handle turns more and more tightly; you have to lean on it with all the weight of your body. This causes distortions in the canvas. If you follow all the rules, it will last much longer. Metal fittings are lubricated with technical petroleum jelly.

How to adjust a plastic door

Adjusting a plastic door begins with identifying defects. This can be done using a paper strip. It is placed on the frame with the door open and the sash is tightly closed. After this, you need to pull the paper towards you. If it pulls out without effort, this means that the door is not pressed well against the frame. In this way it is checked along the entire perimeter. The adjustment pattern depends on those places where the paper is not held tightly.

If the blade has shifted in the horizontal direction, you need to remove the plug from the hinges and tighten the screws. After this, use a hex key to rotate the horizontally located adjusting screw. In this way, the horizontal displacement of the PVC door is adjusted.

Sagging of the canvas

Often the door sag under its own weight. When the canvas is displaced in the vertical direction, it is simply returned to its place by rotating the adjusting screws, which are located at the bottom of the hinges. To do this, use a hexagon. If the operations are performed correctly, the plastic flap will take the desired position and will be in close contact with the box.

If you move the door in height, it moves up to 2 mm. When the adjusting screw is rotated counterclockwise, the door leaf lowers. Clockwise - rises. The main thing is not to rush. The desired result can only be achieved by correct adjustment of the door hinges.

Mashing

With a large degree of vertical descent, the leaf begins to touch the elements of the door frame. The fabric is rubbing. The malfunction is adjusted by moving the blade to the right or left. It is recommended to start work from the bottom. To perform the operation, you need to take a hexagon and insert it into the corresponding hole. The PVC door will begin to move towards or away from the hinge. In the same way, the upper part of the structure is moved to the desired location.

We adjust the pressure ourselves

Over time, a situation may arise that the PVC door does not open or opens, but with difficulty. In this case, frontal adjustment of the structure is used. You can adjust the pressure of a plastic door in two ways:

• using eccentrics;
• using a clamping mechanism.

The eccentrics are located along the perimeter of the end part of the door leaf. The clamping mechanism is located in the canopy area. To adjust the pressure using eccentrics, you need to rotate them around their axis. As a result, the pressing force of the canvas to the box will change. If the eccentric moves towards the room, the clamp will weaken. This position is recommended for the summer season. For winter, you need to turn the eccentrics towards the street. All eccentrics rotate in the same direction. This can be done with a special key or pliers.

Loose fit

It is a little more difficult to adjust the door with your own hands if it does not fit tightly. You can notice this problem by the sensations when turning the handle - in this case, you have to apply more force. In this case, the eccentrics are already set to the winter position. You can put them in the middle position, which will loosen the pressure. If this does not help, the reason lies in the handle: its entire mechanism is clogged and the blade does not close well.

Instructions for adjusting the handle

There is often a situation where the handle has become loose. In this case, you need to adjust it. To do this, the decorative trim is rotated 90 degrees to release the mounting screws. These screws are unscrewed and the handle is removed. Then you should carefully inspect the parts and, if necessary, replace the faulty ones. Assembly is carried out in reverse order. An assembled and lubricated handle will serve you well for a long time.

Adjusting plastic doors yourself is a simple matter. To perform all operations, it is necessary to open the sash to gain access to all mechanisms. The adjusting screw is tightened with a 4 mm hex key.

Required Tools

To carry out repair and adjustment work, some tools are needed:

1. hex keys;
2. flat screwdriver;
3. Phillips screwdriver;
4. plastic gaskets;
5. roulette;
6. rubber seals (not always);
7. adjustment instructions.

This set of tools is enough to carry out high-quality work. All that remains is to monitor the serviceability of the design:

• if necessary, the old seal is removed and a spare one is installed;
• you need to monitor the level of the canvas in the horizontal plane;
• the sides of the hinges must always be firmly secured;
• adjust eccentrics in a timely manner;
• regularly lubricate all components and parts.

These actions will extend the life of PVC doors.

Sections of the article:

Adjusting plastic doors is a process that is designed to eliminate all sorts of problems that have arisen during the use of the structure. No matter how expensive the door and its components are, items always break, especially those that are used frequently.

Door adjustments are most often required because the hinges can weaken and become loose. As a result, the door is uneven, and a draft blows from the opened cracks. The root cause of failure is the wear of individual parts, but their quality also plays a significant role. That’s why you shouldn’t skimp on quality, so that you don’t have to think about adjusting the plastic door in the future.

If you have problems with a plastic door, but don’t want to contact the experts, you can fix the damage yourself. But for this you need to prepare and find out the answers to the following questions:

• Where in the door are the parts intended for adjustment located?
• What problems can generally arise with plastic doors and how to solve them;
• How exactly is a plastic door adjusted?

What is responsible for regulation?

To adjust the door, you will need a hexagon with a diameter of 4 millimeters (most often), sometimes pliers will be useful.

The first adjustment unit can be found on the lower door hinge; by turning it with a hexagon, you can raise or lower the door, depending on the direction of twist.

Here you can also find a node that moves the bottom of the door to the right or left. Sometimes the adjusting screws are covered with protective caps that are easy to find and remove. To move the top of the door to the left or right, you need to twist the screw located at the top hinge.

The clamping force of the door against the door frame is controlled by eccentrics, which can be found throughout the door body. By twisting them, you can achieve precise adjustment of plastic doors and their tightness by changing the pressure in individual areas. In doors with a tilt-and-turn operating principle, there is a way to adjust the pressure of the entire upper part. To do this, you need to turn the screw located at the top of the door.

Getting to this screw is quite difficult; you need to put the door in both the ventilation mode and the “wide open” mode. A built-in mechanism that can be bypassed protects against such opening. You just need to open the door, align the plate that is located at the end of the door near the handle (parallel to the rubber seal) and turn the door handle to ventilation mode. This is a rather complicated procedure, so to know exactly how to adjust a plastic door in this mode, we recommend that you watch the video.

Adjustment methods for various problems

To correct deficiencies, you need to know which screw is responsible for what, and for what problems you should turn it.

This is due to the complexity of the door design and the abundance of all kinds of screws, the incorrect twisting of which can lead to complete breakdown of the mechanism.

Upon request, adjusting plastic doors, you can find many videos from professional craftsmen that will help in the work.

Sagging

Over time, the input protection sags under its own weight, and due to the fact that it is mounted in the air. This is one of the most common problems and at the same time unpleasant, since in this case the lower profile rubs against the frame, and in difficult cases the door becomes difficult to close. In this case, we will definitely have to worry about adjusting the plastic door before the situation gets worse.

To fix this problem, you need to lift the door up. This can be done using a special hole in the middle of the bottom loop. By inserting and turning the hexagon clockwise, we will raise the door higher. If you need to lower the door, you will have to turn it counterclockwise.

In the case where the frame only touches the part of the door opposite the hinges, horizontal adjustment of the top hinge will help. By inserting the tool into the hole and turning it clockwise, we will pull the upper section of the door closer to the frame.

Adjusting plastic doors against sagging can be done independently, but to know the purpose of all screws and connectors, you need instructions from the manufacturer.

Friction on the box

If, when closing and opening, the door rubs against the frame, you need to know how to adjust the mechanism by moving the plastic doors to the left or right. First, we move the lower part by turning the hex key in the connector in the lower hinge, and then do the same trick with the upper one.

Bad pressure

If a draft is blowing from your door, then most likely the pressure of the door to the frame has weakened. This can be corrected by adjusting the plastic door, namely the eccentrics. The mechanism of their operation is that when closing, the eccentric climbs behind the pressure plate.

It follows from this that to increase the pressure it is necessary to turn each of the connectors exactly the same way. You should not assume that the stronger the twist, the more reliable the clamp; with extreme pressure, the seal may dry out and stop doing its job. Craftsmen recommend loosening the pressure in the summer to give the sealing rubber a little freedom and provide a little additional ventilation in the house.

Difficult closing

Another common problem with plastic doors is that you need to apply force to close them. Most often, force is required when turning the handle.

Such symptoms indicate that the eccentrics are in winter mode, and to make closing easier, the screws need to be loosened.

Before adjusting plastic doors, you need to watch a training video to know the required tightening level.

Another reason for difficult closing may be a clogged door mechanism. In mild cases, you can get by with complete lubrication; in difficult situations, you will have to disassemble the door and clean the system.

If the door is used for a long time, the handle may become loose. To correct this problem, rotate the top plate of the handle base and tighten the bolts underneath it.

Adjusting doors with GreenteQ hinge

If the door is heavy (more than 40 kg) and is often used, in most cases it is equipped with GreenteQ type hinges. Adjusting plastic doors, especially on your own, can be a problem, so before starting work it is recommended to watch a video of the process. They can be adjusted in three planes:

• Vertical;
• Horizontal;
• Press to the box.

To access the hinges, you need to remove the plastic protection from them, which is quite easy to do. To raise or lower such a door, insert the hexagon into the socket located at the bottom of the hinge and adjust by twisting to one side. Remember that the adjustment of plastic doors begins with the bottom hinge, and then the middle and top ones are adjusted to it, which can be done independently.

To move the doors left or right, screw in or out the screw located in each hinge under the decorative mask.

To adjust the level of pressure, insert a hex key from the top end of the loop, and use circular movements to change the position of each of them. Now you know how to properly adjust displaced or weakened plastic doors using your own hands.

So, adjusting PVC doors is a simple process, but it requires care and perseverance when doing it yourself. Now you know how to adjust a plastic door without calling specialists to your home.

Even the best doors can begin to creak or sag over time: no one can cancel the force of gravity and friction. And if you have heavy steel ones, then even the metal will get tired of holding them. After the summer, plastic ones also “sag” - they almost always remain open in the heat, which leads to such results. There is no need to tolerate these “disgraces,” nor is there any need to spend money on eliminating them. Although adjusting the entrance doors is a delicate matter, in most cases you can do it yourself. Once you have adjusted the hinges and the rebate with your own hands, you can easily repeat it later.

Adjusting a metal entrance door

• creak;
• draft - blowing from under the canvas (cracks around the perimeter or from above/bottom);
• closes with difficulty.

The solution to all these problems is called “adjusting the front door,” but this includes very different measures - from banal lubrication and replacement of the seal, to actual adjustments and mechanical influences.

Sometimes, to fix a problem, you need to go through all the methods, and sometimes the problem that has arisen can only be eliminated radically - by replacement. Most often, this situation occurs with cheap Chinese products. Adjusting Chinese-made entrance doors is almost impossible. Of course, you can try to do something with your own hands: companies and craftsmen do not undertake them.

Eliminating the squeak

Doors can creak for two reasons: the hinge grease is clogged or the door leaf touches the frame. Although both are called “creaking”, the nature of the sound is different. It’s easier to deal with clogged loops, so they usually start with this procedure.

Hinge lubrication

First, remove the old grease, at the same time removing any dirt stuck to it. The procedure is standard: wipe with a soft cloth wherever marks are visible. If this procedure has not been done for several years, and the hinges are of a standard classic type, and even detachable, the fabric can be removed. It is better to clean it when removed.

If the hinges are rusty and cannot be removed even though they should, do not try to knock them off with a hammer or sledgehammer. You'll do more harm than good. It is better to buy a rust remover. It is usually sold in the form of sprays. Apply to the rusted hinge and wait for the prescribed period. Then remove the fabric from the loops and clean it. But this time it is necessary to remove all the rust. To bare metal, then coat with rust converter and only then with lubricant.

After the old lubricant is removed, take “fresh” and apply it to the hinges. If the blade is removed, no problems will arise - lubricate the pin and ring. If there are any other rubbing mechanisms visible on the frame, lubricate them too.

In traditional type hinges, creaking may occur due to the fact that the washer on the rod has worn off. You inspect it after you have removed the door panel. If there are signs of wear, replace them. Install a new carbide washer. You can use an engraver instead. It will also compensate for the load.

If the hinges are permanent, find a liquid lubricant in a can (the most common is WD40) or machine oil, which can be applied using a large syringe. Handle all rubbing parts carefully.

There is another method, but it is destructive. A hole is drilled in the upper part of the loop, which is then filled with lubricant. The trick is to not damage the mechanism inside.

If the hinges are hidden, find all the turning parts and lubricate them. Often these models have holes into which oil is applied.

After applying the lubricant, rock the doors from side to side several times, distributing the lubricant. If this was the reason, the squeak goes away. The final touch is to wipe off excess oil.

How to lubricate front door hinges

You must select a lubricant primarily based on the temperatures at which the loop is operated. If the loops go outside, you need a composition that does not thicken at low temperatures. There's not much choice here:

• Litol. Operates reliably at temperatures from -40°C to +120°C.
• Solid oil. The temperature range is slightly lower, but also sufficient: from -35°C to +65°C.

For entrance doors facing the entrance and operated at above-zero temperatures, several more items can be added to this list:

Eliminating friction on the box

If the creaking remains after processing the hinges, it is most likely caused by friction of the door leaf against the frame. Inspect the door frame for scuffs. If you find any signs of abrasion, look at which loop is closest. It will need to be regulated, if possible.

The difficulty is that there are a lot of types and models of loops and it is impossible to say unambiguously what needs to be done. All that is possible is to list the main points that may exist. Based on them, you may be able to determine how to “treat” your door.

Two types of hinges for an entrance metal door with adjustment

Standard hinges do not provide adjustment options. In this case, adjusting the entrance doors consists of replacing the washer. Select them of greater or lesser thickness, adjusting the position of the door leaf. Some hinges with a ball at the top have an adjustment screw. By unscrewing it, we lift the doors a little, and by twisting it, we lower them. You can try to correct the situation with its help.

If standard hinges on a steel door are welded, we can assume that the possibilities have been exhausted. If they are mounted on screws, loosen the fastening screws and move the sash in the desired direction as far as possible. Then the screws are tightened. Check to see if the problem has gone away. If not, try with another loop. Sometimes it is necessary to loosen all the loops and tug the canvas in this position. In general, decide where to press and where to press.

There are hinge models in which the adjustment holes are hidden under a protective cap. But you can’t just remove it: it is secured with a bolt that can be unscrewed from inside the room. An example of adjusting such a loop is in the video.

If the hinges on the front door are screwed on, you can use them to eliminate friction between the door leaf and the frame. First, loosen the screws near the area where the wear occurs. Try to move the door leaf a little. To begin with, you can knock with your palm or fist, moving it in the desired direction. Try opening/closing a couple of times. Did it help? Screw the clamping screws back. And try to open/close again.

If it doesn’t help, you can use some kind of leverage, hit it with a rubber mallet or hammer through the board. But don't overdo it. You need to handle Chinese products especially carefully: they are very flimsy.

If these manipulations also do not yield anything, you will have to loosen the screws on all the hinges and try to move the canvas over the entire area. Take the edge of the canvas with your hands and shake it. In this case, the loops should fall into place. You try to open and close. If there is no squeak, tighten the bolts. That's all, adjusting the front door hinges can't do more. The next thing you can try is to change the geometry of the door frame. More on this in the next paragraph.

The photo above (right picture) shows an adjustable hinge. By loosening the screws, you can turn the adjusting screw. It doesn’t help - we try to move the canvas as described above.

Eliminating a leaky door (blowing from under the door)

Sometimes there is a noticeable blow from under the front door. If you examine the perimeter, you will most likely find that in some place the fit of the door leaf to the door frame is loose. There may be a decent sized gap. You can check your suspicions with a piece of paper. Open the doors, insert a piece of paper between the door leaf and the jamb and close the doors. If the rebate is normal, the paper either stretches with very great force, or is clamped so tightly that it is impossible to remove it. Just break it up. If the sheet comes out freely, then the fit is insufficient.

The simplest explanation is that the seal has lost its elasticity. If the doors are several years old, this is possible. And the first thing you do is change the seal. Didn't help or only partially solved the problem? Let's move on.

Replacing the seal is the first step if there is leakage from under the front door

If the door leaf is displaced relative to the door in the horizontal plane, we try to eliminate the draft from under the front door by first moving the door leaf. This is described above: loosen the fastening screws on the hinges, then try to move the blade in the desired direction. Check the result - the gap has disappeared - tighten all the screws to their original position.

Sometimes gaps under the front door occur due to the door frame being skewed. This is checked using a level. Most likely, it is skewed in the place where the sheet of paper can be easily removed. The second option, on the contrary, the box was pushed out in the place where the sheet is pressed, due to the fact that the “normal” part cannot be pressed. All this is determined using an eye gauge and a level. Having determined what the problem is, we try to return the geometry to normal. The measures depend on how the box is installed:

For an option to correct the gap in the vestibule, see the video. After entrance door installation It turned out that it was blowing strongly from under it. The owner corrected the distortion with a hammer.

Eliminating door sag (shuffles on the threshold)

If, after several years of operation, the doors begin to open with difficulty and rub against the threshold, most likely the problem is that the ball or bearings have worn out. If there are possible adjustments, you won’t even have to remove them. Simply unscrew one of the bolts and lift it slightly up.

If there is no adjustment, there are several options:

• replacing hinges;
• replacing bearings with new ones;
• installation of washers instead of bearings.

All this is determined based on the situation and the design of the loop.

Adjusting plastic entrance doors

The problems may be the same: friction, creaking hinges and loose connection to the frame, which can cause blowing. But adjusting PVC doors is simpler - the hinges and mechanisms are standardized, there are not many types. So there is hope that you can deal with the problems yourself, without calling a specialist.

Balcony door adjustment

After the summer, the plastic doors to the balcony sag: in the summer they often remain open for a long time, which is why such a nuisance happens. Then they touch the threshold, an unpleasant sound is heard, and the plastic is erased. In this case, you need to lift the canvas up. This is done using the adjustment located at the top of the lower hinge.

They do this with the lock open, but the door is closed. Take a hex wrench (usually 4 or 5) and insert it into the hole and turn it a few turns. There is no need to lift too much right away, as this can cause other problems. Raise only until the problem is fixed.

Sometimes, when closing, the doors rub from the side, hitting the metal latches. It turns out that you need to move the canvas towards the loop part. For this there is another adjustment on the same hinge. It is located below, visible when the door is open.

This adjustment is also carried out with a couple of turns clockwise or counterclockwise. If you need the doors to not rub against the counter, turn counterclockwise. Give it a couple of turns and check. Once the problem goes away, stop. Otherwise, you can move it so much that the lock stops “clinging” to the mate.

If the upper left corner “clings”, you need to adjust the loop that is located at the top. The principle is the same: one or two turns until the problem is eliminated.

Top Hinge Adjustment - Top Left Corner Pressure

Pressure adjustment (to prevent draught)

Sometimes weak pressure is observed from the side of the locking part. It seems that the canvas adjoins smoothly, but there is a noticeable pull from under the door. In summer this is not a problem, but with the onset of cold weather it significantly reduces the temperature. There are two ways. The first is to adjust the clamping pins. These are metal protrusions on the sash.

They come in two types. as in the photo above - oval and round, but with an eccentric in the middle. The position of this element determines the degree of pressing of the sash to the frame. The method of changing the position depends on the shape of the trunnion. If it is like in the photo, take pliers, clamp it and turn it slightly. The maximum pressure is if the long side is turned horizontally, the minimum is if it is directed vertically upward. There are also all the intermediate options.

If there is an eccentric in the center of the trunnion, then there is also a hole for the hexagon. Insert it and turn it, achieving the desired degree of pressure.

It is not recommended to set the stasis to the maximum value: the seals will quickly lose their elasticity. Also make sure that all eccentrics are rotated the same way. This guarantees normal operation of the fittings.

But sometimes there is a situation where the balcony door leaf is not pressed tightly on the hinge side. This can also be eliminated by adjusting the hinges. At the bottom it is located under a protective cap. Remove it (pull it up). Take the key (hexagon) and with a couple of turns adjust the clamping of the lower right corner of the plastic balcony door.

There are also hidden hinges on the frame, which also provide the ability to adjust the pressure. They are located on the frame on the hinge side. Adjustment with the same hex wrench. Turns “clockwise” and “counterclockwise”.

Adjusting plastic entrance doors

The plastic entrance doors have different hinges, and there are no locking and tilting fittings. They have closed loops of the overhead type. They have three adjustments:

• the height of the door leaf relative to the frame - at the bottom of the hinge;
• the density of pressing the canvas to the frame is on the top on the hinge;
• sash movement horizontally - sideways

They are sufficient if the doors were initially installed correctly: the limits for changing positions are significant, which makes it possible to compensate for those changes that occurred during operation.

If there is a squeak in the hinges, they need to be lubricated. To do this, remove the top cap and put lubricant into the opened hole. Since plastic doors are installed as entrance doors mainly in private houses and they go out onto the street or into an unheated vestibule, you select a lubricant that does not thicken at low temperatures (Litol and Solidol).

Put lubricant here

In some models of hinges, the lid is simply lifted off, in others, you need to unscrew it and then pull it out. Determined by location.

Sometimes a situation arises when intervention is required: the lock does not lock properly. If the sash pressure is normal, correction of the striker is necessary. She is mobile in such doors. Loosen the mounting screws, use a screwdriver to move the bar slightly in the desired direction and tighten the screws back. Checking. It should help.

All malfunctions of a balcony door or window that occur during the warranty period are eliminated by the installer.

But as soon as this period expires, you will need to invite a specialist, which can be very expensive. However, many problems can be solved on your own, you just need to find out how to do it correctly.

Features of malfunctions of balcony doors

When the installation of a new balcony door is completed, the installers make its initial adjustment, thanks to which the door functions flawlessly for some time. However, this does not last indefinitely; over time, the tightness of the door decreases, cold air enters the room or other malfunctions appear and does not even help prevent this.

They occur much less frequently with windows than with doors. Many problems can be solved by adjusting the pressure of a plastic balcony door, which must be done correctly and in a timely manner. After all, solving small problems is easier than eliminating major malfunctions.

Therefore, you should not wait until the balcony door stops closing. If you notice that cold air is entering the room and the canvas is not pressed quite tightly against the frame, call a specialist or do the adjustment yourself.

Ensuring normal pressure on the balcony door with your own hands

How to check the tightness of a door

1. In order to determine whether adjustment of the pressure of a plastic balcony door is required, you need to take a sheet of paper, place it on the frame of the open door, close the door and try to pull the sheet towards you.
   This action should be carried out around the perimeter of the door.

At the same time, it is important to note the strength of the efforts that have to be made. If this becomes easy to do, it means that the door leaf has lost its former tightness.

1. If you suspect that the door leaf is not quite level relative to the frame, you can do the following manipulation: close the door, trace the door with a simple pencil, open the door and evaluate the evenness of the line.
   It is not forbidden to use a level.

Using these simple methods, you can always identify problems in a timely manner and respond to them.

How to adjust a balcony door yourself

A plastic balcony door differs in many ways from a wooden one. Its main advantage is that it is relatively simple.

On the modern market you can also find various designs of plastic doors, but the principle of their operation is similar, as well as the principle of their adjustment. Therefore, there is a general algorithm for troubleshooting.

In order to do this, you need to have the following set of tools:

• screwdrivers (phillips and flat);
• hex keys (better if it is a set);
• pliers;
• roulette;
• plastic gaskets.

Sequence of work when adjusting the door