home · On a note · Installation of a 5 meter spring tape measure. Disassembly and repair of measuring tape. Construction tape measure body

Installation of a 5 meter spring tape measure. Disassembly and repair of measuring tape. Construction tape measure body

When measuring at summer cottages large objects (sizes from 3 m) The spring of the return mechanism of the roulette often breaks. The reason is the excessive force applied when drawing out the measuring tape (in everyday life “centimeter”) after the last size appears - either out of necessity, or out of carelessness. In this case, it is no longer possible to manually return the unwound measuring tape to the tape measure body, which complicates or eliminates its further use. A sad incident, especially if you liked the design of the instrument, and even if the measuring tape was in good condition.

However, the measuring tape of a collapsed tape measure with a length of 3 m will continue to serve if you combine it (see photo 1) with a stationery clip for papers of the EK model and with a manual strap, like that of umbrellas, purses or handbags, equipped with a carabiner - these things are easy purchase in the store.

To begin with, the belt must be disengaged from the defective return mechanism. At the free end of the tape, with a deviation of 4-6 cm from the end, it is stitched in the middle mechanically(drilling, stamping, punch) hole with a diameter of 1.8-2.2 mm.

The end of the tape that has been freed from the snag (see photo 2, above) is folded into a single-layer ring oval shape until the technological hole (the coupling of the tape with the spring of the return mechanism) is aligned with the newly formed hole, it is tied along the combined holes with strong thread or thin soft wire, after which this connection area is wrapped with narrow tape.

In this case, one mandatory condition must be met: the dimensional side of the tape when winding it on the formed single-layer oval ring must be on inside the formed skein, which will protect the measuring scale from contamination and erasing the markings during the operation of the tape.

Next, the free end of the tape is wound onto an oval ring. If necessary, during the winding process we make successive tightenings of the tape in order to achieve tight contact of the already wound layers to each other.

A construction tape measure is one of those tools that are in great demand in everyday life. True, many of us use it only as a regular ruler: after measuring, it is wound up and put away old place. The full capabilities of roulette are known only to real masters who use them to the fullest in the course of their work. Why shouldn’t ordinary home craftsmen discover the secrets of this familiar device? It was this question that gave us the idea to write this article.


The role of the hook itself, which is equipped with a construction tape measure, is known to almost everyone. Thanks to it, measurements can be made either from an object or by capturing it.

However, few people know why this grip is movable. Considering this a defect, some even try to fix it by placing a rivet there. In reality, the play in the toe is intended to compensate for the thickness of the toe. Setting the amount of play equal to the value hook, measurement can always be made from zero.

But this is not the only trick in the hook. It almost always has a hole designed to engage the head of a nail or screw.

How a construction tape is adapted to take measurements in corners

Very often it is difficult for craftsmen to measure distances that end at an angle. In reality, the measurement should be done in a completely different way: you should place the tape measure body in the corner, take the measurement and add the length of the tape measure body to the resulting value.

Very often the length of the case is indicated on the tape measure itself.

How to measure if the object being measured is very long

If the object being measured is of impressive size, you can stick a piece of masking tape somewhere in the middle to make the operation easier. This easy-to-peel paper piece can be used as a place for notes. Having measured the distances before and after the piece of paper and written down the corresponding numbers on it, you can add here to get the final result.

Construction tape as a marking tool

The tape measure can be used as a compass or thicknesser by attaching a pencil holder to its body and inserting a pencil there.

If the marking is made on a soft material, for example, on drywall, you don’t even need a pencil. Marks can be left with a hook, having previously made several notches on it with a needle file.

With a tape measure, all the notes can be before your eyes

When taking several measurements at once, there is always a risk of forgetting or confusing the numbers. To prevent this from happening, experts glue a piece of masking tape to the body of the tape measure.

How to use a tape measure to divide segments into parts

You can divide by two using a roulette even without using your mathematical abilities. To do this, the tape measure zero is combined with a number reflecting the measurement value, and the finished result is found at the bend of the measuring tape.

To divide into equal segments, you can also use another original technique that avoids the need to perform mathematical calculations. Let's say we need four such segments. To select strips of equal width, it is enough to place the measuring tape of a tape measure on the part so that its edge is near the round number on the measuring tape, for example, 20 cm. Marks in such a case You will need to put it next to the numbers 5, 10, 15.

So, it would seem that a very simple tool like a construction tape can turn into multifunctional device, capable of handling a fairly large number of tasks. The only thing is to know how to do it and be able to perform this operation.

A tape measure is a tool you can’t do without in everyday life. True, for many its use is limited to the properties of a regular ruler: take it out of your pocket, make necessary measurements and rolled it back. And only true masters of their craft know how to use a tape measure correctly and effectively, and in what situations you cannot do without it.

In contact with

Classmates


1. Why do you need a movable hook?


Despite the fact that almost everyone has a tape measure in their home, not everyone knows what the movable hook is for. Some people don’t pay attention to it, while others even consider it a defect and try to fix it - install a rivet to secure the hook. However, in a word, only a few are used for their intended purpose.



In fact, the play serves to compensate for the thickness of the hook, depending on how the measurement is carried out - from the object or with its grip. By adjusting the position of the hook, the master receives accurate measurement data, since the measurement is always made from the zero mark.

2. How to measure in a corner


Measuring in a corner or opening is a task that usually brings a lot of inconvenience to the master. In fact, there is no need at all to try to perfectly accurately lean the measuring tape against the wall: it is enough to bring the tape measure body to the end of the measured distance, and then add its length to the result. By the way, finding out the length of the casing is also easy: most often, for convenience, manufacturers indicate this indicator on the casing of the tape measure.




3. Measuring an object that is too long



If you measure an object of impressive size yourself, then this life hack will help make the task easier: stick a small piece of masking tape approximately in the middle of the object. This material has beneficial properties: it peels off easily different surfaces, and it is also convenient to write on it with a simple pencil. Next, you need to take two measurements, marking on the masking tape the point from and to which measurements are taken. We recommend writing down the resulting numbers on the same piece of masking tape, and then adding up the two results obtained.

4. And once again about the movable hook


There is almost always a hole in the movable hook plate on all types of tape measures. Of course, the designers placed it there for a reason. The hole is used to hook onto a nail or screw where possible and necessary for taking measurements. The error of the result with this method varies within only 1-2 mm.


5. Marking with a tape measure


A tape measure from a regular meter can easily turn into a compass or surface planer (a tool for marking and transferring drawings to a workpiece). To do this, just attach the leg of a compass with a pencil to the outside of the tape measure. It’s good if you have an old tape measure available, then it can be converted into a drawing tool and used only when necessary.



In cases where you have to work with soft materials(for example, with drywall), you can even do without a pencil. It is necessary to sharpen the notches on the toe with a needle file, and, pressing lightly, leave marks in in the right places.

6. Always have a place for notes at hand



Instead of constantly memorizing numbers, afraid of making a mistake at some point, it is better to get used to making notes directly on the tape measure. The easiest way is to place a small strip of masking tape on the body. If you don’t have such material at hand, you can write on the body itself with an erasable marker.

7. Dividing segments in half and into several parts


Divide in half, not counting


This mathematical trick is simple and straightforward, but at the same time, only a few people use it in their work. To divide any number by two, just find it on the measuring tape and align it with the zero mark, and fold the tape itself in half. The answer number will be located on the fold.

When working with a measuring tape, many have more than once encountered such a situation when the metal tape “refuses” to wind up into a reverse spiral. If this is your first time encountering such a snag, don’t rush to throw it away. roulette– it is still possible to repair it.

You will need

  • Tape measure, screwdriver.

Instructions

1. The convenience of measuring with a tape measure is that you can always quickly take measurements from some objects. However, over time, the efficiency disappears somewhere, the tape stops independently curling into a spiral and you have to wind it up manually. This is not particularly troublesome if you need to reel in 0.5-1 meter. The problem manifests itself when the tape is released to its full length. If you don’t want to bother with fixing the tape measure, you can throw it away and buy a new one. But why spend extra money when in a few minutes you can return the instrument to its former novelty?

2. First you need to disassemble roulette. The sides of the measuring tool can be held on by one or four screws. You need to unscrew these screws, then remove one of their sides. Inside the tape measure, in the very center, you will see an additional metal spiral, which will probably be pulled off. You need to twist it again.

3. To twist the spiral, pull the tape out to its full length, then remove it (this will make it easier for you to wind the spiral again). Later, after you unfasten the tape, correct the position of the spiral so that its surface is perfectly flat (without differences) and twist it. Attach the measuring tape back and rotate the spiral until each tape is gathered into a ball. Make sure that there is no dust left between the layers of tape (the tape measure often has to be repaired under repair conditions). After the tape is assembled, put on the previously removed side of the tape measure and tighten the screws back. Now the tool will work as if you just brought it from the store.

There are methods to beat roulette. Finally, strategies do not provide an unconditional guarantee of winning. And it’s unlikely that you’ll be allowed to win much. However, you may still receive some income. The most important thing is not to get too enthusiastic. Only a cool head and sober calculation will give you the chance to win.

You will need

  • -Roulette Assault program.

Instructions

1. To play, choose a casino that allows skipping moves. In this case, you will have the opportunity to test a virtually win-win roulette system. Register on the casino website and deposit a minimum of 300 rubles into your account.

2. Start playing idle. Play this way until the same color, say red, appears five times in a row. Now bet on the opposite color – black. Bet 1 ruble. As soon as red comes up again, bet on black, but double it. Now it will be 2 rubles. And so increase the bet every time the opposite color appears.

3. The chance of one color appearing 12 times is very low. If it lands 10 or 11 times in a row, you have a chance. The game system, of course, leaves room for risk, but reduces it significantly. You can start not with five “idle” moves, but with 10. This will increase the chances of winning up to 100%. The only inconvenience is that it will delay the game for a long time. On the contrary, it is possible to reduce the number of “idle” strokes. The game will go much faster, but the risk will increase several times.

4. You can increase the bet itself. Of course, the winnings in this case will also increase. Just make sure that the minimum and maximum bids are suitable for you.

5. You can also play roulette with the help of special software. Roulette Assault is a strong analyzer program with the possibility of a mechanical game. In theory, the program does the same thing - bets on the opposite color after the same color has fallen out multiple times. Undoubted convenience - you are not required to be at the computer. In addition, the program plays much faster than a person. A significant drawback is the cost of the key, about 50 bucks. A certain setting for a specific casino is also required.

Video on the topic

Roulette- this is the most common measuring tool. In this article we will look at the design, purpose, as well as the main types measuring tapes. Only mechanical ones will be considered here. roulette, laser roulettes a separate article will be devoted.

Purpose of a measuring tape.

Measuring tapes used for measuring extended linear objects and marking rooms.

Types of roulettes.

Exist short and long roulettes:

  • Short roulettes 2-10 m are equipped with a spring winding mechanism and a stop button, which allows you to fix the tape at a certain length.
  • Long tape measures 10-25 m have a manual twisting mechanism and a plastic tape with a ring at the end, they are also called measuring tapes.

There are also roulette with electronic device reading and with electric drives for tape rewinding.

Design of a measuring tape.

Yardstick consists of a metal or plastic tape with a measurement scale printed on it. Usually the tape length is 2-10 m, there are roulette with a tape length of up to 25 m. The metal tape has a concave shape for greater rigidity. Tape width 12.5-25 mm.

The tape is placed in a metal or plastic case. Sometimes the body is made of rubber to increase impact resistance roulette.

Also measuring tapes equipped with a winding mechanism: manual, spring or electric. Manual mechanism equip long tape measures(with a length of more than 10 m). Equipped with a spring winding mechanism short roulettes, such roulette They also have a tape lock button.

At the end of the tape there is a hook or ring with which the tape clings to the beginning of the object being measured, and also prevents the end of the tape from winding into the body.