Pumping station aqua robot jet 80 l. Aquarobot of the jet l series is universal. Aquarobot ensures reliable shutdown of the station

Adaptive automatic pumping station AQUAROBOT JET S series- with a 2 or 5 l hydraulic accumulator designed to supply clean water, which does not contain abrasive particles and fibrous inclusions, from shallow wells, wells and other water supply sources in automatic mode(turning on and off as the consumer consumes water). The stations are equipped electronic unit, which controls the operation of the pump in terms of flow and minimum pressure (Pmin), and also protects the pump from operation in the “dry running” mode and other emergency situations(drop in mains voltage, incorrect installation, etc.).

Advantages of the automatic adaptive station AQUAROBOT

• Automatically turns off when there is no water in the water supply system.
• Automatically switches off when the pump impeller becomes jammed.
• Operates stably when the mains voltage drops to 170 V.
• Automatically turns off if there is no air pressure in the accumulator.
• Automatically turns off when water leaks from the water supply system, if the flow rate is no more than 2 l/min.
• Adaptively maintains pressure in the water supply system, which significantly increases the service life of the pump.
• Operates stably at a critical suction depth of 8 meters.
• It automatically turns off if the station is incorrectly connected to the water supply source (for stable operation at low voltage or a critical suction depth of 8 meters, the water flow rate must be more than 2 l/min).

The principle of operation of the station is that when a water flow passes through the control unit at a speed above 2 l/min, or when the pressure drops below Pmin (1.5±0.3 bar), the pump turns on and pumps water continuously, creating pressure, the value of which depends on the pump parameters. When the water flow stops or its speed decreases to 2 l/min, the pump automatically turns off with a thirty-second delay.

AQUAROBOT provides reliable shutdown stations

• In low well productivity mode (“dry run”)
• If there is no air in the accumulator (no pressure)
• When the water flow is below 2 liters per minute (line leakage)
• In the mode of dynamic fluctuation of the water level in the well below 8 meters
• In case of improper installation of equipment and water supply lines

In the event of an emergency shutdown of the pumping station, it is necessary to eliminate the cause and restart it.

Attention. The use of the station in pressure boosting systems is not allowed if the pressure created by the pump, combined with the main pressure, is higher than or close to 6 bar.

Technical information

• Options electrical network– ~220 V ± 10%, 50 Hz
• Suction height – 8 m (for AQUAROBOT JET, JS) / 5 m (for AQUAROBOT QB)
• Operating water temperature range – +1 ... +35°С, at temperature environment+1 ... +40°С and air humidity no more than 70%.
• Connecting dimensions: 1" external thread x 1" internal thread
• Pressure compressed air in the hydraulic accumulator – 0.15 MPa (1.5 bar)
• Maximum permissible pressure in the system – 6 bar
• Pump activation pressure Pmin – 1.5±0.3 bar
• The minimum sensitivity of the flow sensor is 2 l/min.

Technical information

Pressure and flow characteristics

* - the given data on maximum pressure and productivity are valid at zero suction depth and an electrical network voltage of 220V±10%.

AQUAROBOT JET 80 L station is designed for supplying clean cold water, which does not contain abrasive particles and long-fiber inclusions, from shallow wells and boreholes, storage tanks and other sources of water supply in automatic mode (turning on and off as the consumer consumes water).

The AQUAROBOT JET 80 L pumping station is not recommended for use in systems where various Appliances with low water consumption, as well as in systems with narrowed pipeline sections. For such cases, we recommend using universal stations AQUAROBOT.

Advantages automatic station AQUAROBOT JET 80 L with hydraulic accumulator 5 liters

• Automatically turns off when there is no water in the water supply system.
• Automatically switches off when the pump impeller becomes jammed.
• Operates stably when the mains voltage drops to 120 V.
• Automatically turns off if there is no air pressure in the accumulator.
• Automatically turns off when water leaks from the water supply system, if the flow rate is no more than 2 l/min.
• Adaptively maintains pressure in the water supply system, which significantly increases the service life of the pump.
• Operates stably at a critical suction depth of 8 meters.
• It automatically turns off if the station is incorrectly connected to the water supply source (for stable operation at low voltage or a critical suction depth of 8 meters, the water flow rate must be more than 2 l/min).

Scope of application of AQUAROBOT JET 80 L: autonomous water supply for small buildings, irrigation systems for vegetable gardens, garden plots, small farms, increasing pressure in the water supply network.

The station is equipped electronic device, which turns off the pump in the absence of water flow, which protects the pump from operating in “dry running” mode.

The temperature of the pumped water is no more than 35 C.

The pumping station of the AQUAROBOT JET 80 L series is capable of sucking water from a depth of up to 8 m.

Station AQUAROBOT JET 80 L assembled on the basis of surface self-priming pumps of the JET L series with a cast iron pump body and a brass impeller. AQUAROBOT JET 80 L is equipped with a hydraulic accumulator with a volume of 5 liters and a control unit with a flow sensor. The control unit is equipped with a microprocessor that controls turning the pump on and off and protects the pump from “dry running”. The flow sensor has increased sensitivity, 2 l/min.

Adaptive station AQUAROBOT JET 80 L consists of surface pump-(2), flow sensor-(1), hydraulic accumulator with a minimum volume of 5 l -(3) and a microprocessor installed in the pump terminal box (4)

An electronic control unit mounted in the pump's terminal box controls the operation of the pump automatically. When the supply voltage is applied, the pump turns on. We open the tap and water is supplied to the consumer. We close the tap, the flow of water through the flow sensor stops, the pump continues to operate for 15 seconds (delay time), replenishing the accumulator, after which the pump turns off. We open the tap again, water from the accumulator is supplied to the consumer, flowing through the flow sensor. The sensor gives a signal to turn on the pump and the pump turns on immediately, without delay. If there is no water in the suction line, water is supplied to the consumer from the accumulator for some time, then the flow of water through the flow sensor stops, the sensor sends a signal to turn off the pump, the control unit turns off the pump after 15 seconds, thereby protecting the pump from “dry running”.

AQUAROBOT JET 80 L ensures reliable shutdown of the station

• In low well productivity mode (“dry run”)
• If there is no air in the accumulator (no pressure)
• When the water flow is below 2 liters per minute (line leakage)
• In the mode of dynamic fluctuation of the water level in the well below 8 meters
• In case of improper installation of equipment and water supply lines

Based on a centrifugal surface pump with an extended internal ejector JET 80 L (cast iron pump body, brass impeller) and a 5 l hydraulic accumulator, with an electronic device that controls the operation of the pump and protects against dry running, 600 W, Hmax-38 m, Qmax-50 l/ min

Contents of delivery:

• Automatic water supply station assembled - 1 pc.
• Operation manual - 1 pc.
• Packaging - 1 pc.

Technical information

Electrical network parameters~220 V, 50 Hz
Capacity max, l/min 50
Electric motor power, W 600
Head max, m 38
Diameter of inlet and discharge holes 1" x 1"
Maximum suction lift, m 8
Switching pressure, MPa 0,15
Shutdown pressure, MPa 0,30
Pump body material cast iron
Impeller material brass

Universal pumping station AQUAROBOT JET 80 L 24 liters - designed to supply clean cold water, not containing abrasive particles and long-fiber inclusions, from shallow wells and boreholes, storage tanks and other water supply sources in automatic mode (turning on and off as the consumer consumes water) , as well as to increase pressure in the main water supply.

Advantages of the universal automatic station AQUAROBOT

• Automatically turns off when there is no water in the water supply system;
• Automatically switches off when the pump impeller becomes jammed;
• Works stably when the mains voltage drops to 120 V;
• Operates stably at a critical suction depth of 8 meters and below, in dynamic mode;
• Adaptively maintains pressure in the water supply system;
• Automatically turns off if the station is incorrectly connected to the water supply source;
• Possibility of adjusting the upper and lower pressure threshold.

Application area

For autonomous water supply of small buildings, irrigation systems for vegetable gardens, garden plots, small farms, increasing pressure in the water supply network. The stations are equipped with an electronic device that turns off the pump in the absence of water flow, which protects the pump from operating in the "" mode. dry running" and from improper installation of equipment and water mains.

AQUAROBOT pumping stations of the JET L series are capable of sucking water from a depth of up to 8 m. AQUAROBOT JET L stations are assembled on the basis surface self-priming pumps of the JET L series (trademark UNIPUMP). They have a hydraulic accumulator with a volume of 24 liters.

Principle of operation

The pumping station consists of a 24-liter hydraulic accumulator, a PM5-3W device (connecting a PM-5 pressure switch, a five-pin fitting and a pressure gauge) and an AQUAROBOT TURBI device equipped with a flow sensor installed on the pump discharge pipe. The pressure switch controls turning the pump on and off.

The switch-on pressure is adjustable from 1 - 2.5 bar, the switch-off pressure is 1.8 - 4.5 bar. Factory settings are 1.5 and 3.0 bar, respectively. An electronic-mechanical flow sensor with a microprocessor (developed by SABLINE SERVICE LLC) has increased sensitivity - 2 l/min and ensures reliable shutdown of the station in the event of a failure of the pressure switch, as well as in cases where the pump cannot fill operating pressure.

AQUAROBOT ensures reliable shutdown of the station

• in low well productivity mode (“dry run”);
• in the mode of dynamic fluctuations of the water level in the well below 8 meters;
• in case of improper installation of equipment and water supply lines;
• in case of jamming of the pump impeller.

Technical information

Pressure and flow characteristics

* - the given data on maximum pressure and productivity are valid at zero suction depth and an electrical network voltage of 220V±10%.

Contents of delivery:

• Automatic water supply station assembly – 1 pc.
• Operating manual – 1 pc.
• Packaging – 1 pc.

Universal automatic pumping stations AQUAROBOT JET L series— designed for supplying clean cold water that does not contain abrasive particles and long-fiber inclusions from shallow wells and boreholes, storage tanks and other water supply sources in automatic mode (turning on and off as the consumer consumes water), as well as to increase pressure in the main water supply .

Advantages of the universal automatic station AQUAROBOT

• Automatically turns off when there is no water in the water supply system;
• Automatically switches off when the pump impeller becomes jammed;
• Works stably when the mains voltage drops to 120 V;
• Operates stably at a critical suction depth of 8 meters and below, in dynamic mode;
• Adaptively maintains pressure in the water supply system;
• Automatically turns off if the station is incorrectly connected to the water supply source;
• Possibility of adjusting the upper and lower pressure threshold.

Application area

For autonomous water supply of small buildings, irrigation systems for vegetable gardens, garden plots, small farms, increasing pressure in the water supply network. The stations are equipped with an electronic device that turns off the pump in the absence of water flow, which protects the pump from operating in the "" mode. dry running" and from improper installation of equipment and water mains.

AQUAROBOT pumping stations of the JET L series are capable of sucking water from a depth of up to 8 m. AQUAROBOT JET L stations are assembled on the basis surface self-priming pumps of the JET L series(trademark UNIPUMP). They have a hydraulic accumulator with a volume of 24 liters.

Principle of operation

The pumping station consists of a 24-liter hydraulic accumulator, a PM5-3W device (connecting a PM-5 pressure switch, a five-pin fitting and a pressure gauge) and an AQUAROBOT TURBI device equipped with a flow sensor installed on the pump discharge pipe. The pressure switch controls turning the pump on and off.

The switch-on pressure is adjustable from 1 - 2.5 bar, the switch-off pressure is 1.8 - 4.5 bar. Factory settings are 1.5 and 3.0 bar, respectively. The electronic-mechanical flow sensor with a microprocessor (developed by SABLINE SERVICE LLC) has increased sensitivity - 2 l/min and ensures reliable shutdown of the station in the event of a failure of the pressure switch, as well as in cases where the pump cannot reach operating pressure.

AQUAROBOT station ensures reliable shutdown

• in low well productivity mode (“dry run”);
• in the mode of dynamic fluctuations of the water level in the well below 8 meters;
• in case of improper installation of equipment and water supply lines;
• in case of jamming of the pump impeller.

Adaptive pumping station AQUAROBOT JET 80 S 2 liters - with a 2 liter hydraulic accumulator is designed to supply clean water that does not contain abrasive particles and fibrous inclusions from shallow wells, wells and other water supply sources in automatic mode (turning on and off as the consumer consumes water) . The stations are equipped with an electronic unit that controls the operation of the pump in terms of flow and minimum pressure (Pmin), and also protects the pump from operation in “dry running” mode and other emergency situations (drop in mains voltage, incorrect installation, etc.).

Advantages of the automatic adaptive station AQUAROBOT JET 80 S 2 liters

• Automatically turns off when there is no water in the water supply system.
• Automatically switches off when the pump impeller becomes jammed.
• Operates stably when the mains voltage drops to 120 V.
• Automatically turns off if there is no air pressure in the accumulator.
• Automatically turns off when water leaks from the water supply system, if the flow rate is no more than 2 l/min.
• Adaptively maintains pressure in the water supply system, which significantly increases the service life of the pump.
• Operates stably at a critical suction depth of 8 meters.
• It automatically turns off if the station is incorrectly connected to the water supply source (for stable operation at low voltage or a critical suction depth of 8 meters, the water flow rate must be more than 2 l/min).

The principle of operation of the station is that when a water flow passes through the control unit at a speed above 2 l/min, or when the pressure drops below Pmin (1.5±0.3 bar), the pump turns on and pumps water continuously, creating pressure, the value of which depends on the pump parameters. When the water flow stops or its speed decreases to 2 l/min, the pump automatically turns off with a thirty-second delay.

AQUAROBOT JET 80 S 2 liters ensures reliable shutdown of the station

• In low well productivity mode (“dry run”)
• If there is no air in the accumulator (no pressure)
• When the water flow is below 2 liters per minute (line leakage)
• In the mode of dynamic fluctuation of the water level in the well below 8 meters
• In case of improper installation of equipment and water supply lines

In the event of an emergency shutdown of the pumping station, it is necessary to eliminate the cause and restart it.

Attention. The use of the station in pressure boosting systems is not allowed if the pressure created by the pump, combined with the main pressure, is higher than or close to 6 bar.

Technical information

• Electrical network parameters – ~220 V ± 10%, 50 Hz
• Suction height – 8 m (for AQUAROBOT JET, JS) / 5 m (for AQUAROBOT QB)
• The operating temperature range of water is +1 … +35°С, at an ambient temperature of +1 … +40°С and air humidity no more than 70%.
• Connecting dimensions: 1″ external thread x 1″ internal thread
• Compressed air pressure in the hydraulic accumulator – 0.15 MPa (1.5 bar)
• Maximum permissible pressure in the system – 6 bar
• Pump activation pressure Pmin – 1.5±0.3 bar
• The minimum sensitivity of the flow sensor is 2 l/min.

Technical information

Pressure and flow characteristics

* - the given data on maximum pressure and productivity are valid at zero suction depth and an electrical network voltage of 220V±10%.

Contents of delivery:

• Automatic water supply station assembly – 1 pc.
• Operating manual – 1 pc.
• Packaging – 1 pc.