3D cast of arms and legs by hand. Casts of arms and legs. What equipment is required to start this business?

To make a print of your baby's arms or legs, that is, the baby's first footprint, you need to read these instructions.
All materials that are intended for making impressions do not cause any harm and cannot cause.
To make them, you will need a small amount, this will not disturb the child, because the technology by which the impressions are made is innovative, and the composition from which the impression will be made is hypoallergenic.
Specialists have specially developed kits so that parents can create their own children's casts.
Often, parents of children bought sets in stores, but there was not enough modeling material for a sufficient number of casts. But there are kits with which parents have several attempts before the real start. They train and begin to sculpt something truly beautiful and neat. The result is a high-quality cast. They can create it not only for themselves, but also as a gift to grandparents, godparents of their baby, or make casts of the children of close friends as a gift to them.

In addition to casts of your baby’s tiny limbs, you can create a cast of the hands of two lovers or newlyweds, or a cast of your own hand.

Available for sale today great abundance similar things, with the help of which it is easy to create own design casts.
And on the Internet there are many samples for making casts.
If you want to place the resulting cast on a table or shelf, you need to fill a plastic mold, for example, from a candy container, with plaster, paint it with any paint, then glue the resulting cast of the leg or handle using good glue.

Kits for creating 3d impressions

Watch a video on how to properly create a cast:

Now let’s look at this video in more detail: mix the dry gel in the required proportion, beat with a mixer until a homogeneous mass is formed, convenient for use. After this, lower the child’s leg into the mass and remove it. We fill the mold with special plaster, and after a while we take out the resulting sculpture.
Not quite difficult, right?
Now let’s take a closer look at the proportions by which you need to mix water with the impression gel.
Take 100 grams of dry gel, also 400 milliliters of water. Well, to create the hand of an adult, instead of a mayonnaise bucket, they take a two-liter plastic bottle and cut off its neck. Take 250 grams of gel per liter of water.
For children whose ages range from and older, you need to calculate the proportions yourself. To do this, measure required amount water for total immersion the child's hands or feet into the container.
To fill the mold, take special plaster. To fill one cast, take ten-five tablespoons of plaster and 0.05 liters of water.
In order to fill one cast of an adult’s hand, you will need 20 tablespoons of plaster and 0.18 liters of water.

Kits for creating 2d impressions

We create a convex cast of any part of your baby’s tiny limbs.
This technology involves plastic material for reusable use.
It is quite flexible and soft, capable of conveying every fold and line of the skin, and holds its shape perfectly.
But this material can be used almost unlimitedly.
The main condition for storage is that the material must be in a jar, without contact with water, talc and oil.
This kit will help you make your own impressions of children's feet and hands every month. You will compare how the baby has grown.
And now video instructions for creating 2 d impressions:

When analyzing this video, we would like to clarify again that the convex layer of the handle is made using ready-made impression mass manually and filled with special plaster. Then everything dries, the cast is pulled out, and the mass is kneaded again. A new cast is created from it.
After this procedure, the impression mass is kneaded again, it is placed in a bag into which no air will enter, so that the next time the mass can be taken out and the sculpture created again.
The casts can be painted in any color you like. This can be done using watercolor paint, gouache, or acrylic. Glue what you got to the photo frame. At the same time, use any decor that you like, some collages, booties, a tag, a pacifier, an ultrasound image, a bodysuit, a vest, a hat. The main thing is to use your imagination.

Little children grow so quickly that you don’t have time to keep track of them. So he turned over for the first time, smiled, said “mom”, went... got married. And I really want to remember every pleasant moment of this charming child’s life, to capture the little hands and feet in my memory. Today, newfangled trends are coming to the aid of young mothers, thanks to which they can make casts of the arms and legs of your little children. Let's look at several ways to “freeze the moment” and capture the tiny, adorable limbs of a child.

There are a lot of offers on the Internet for creativity kits, with which you can make prints of your baby’s arms and legs with every visible fold on the palm and foot. After all, you must admit that making a collage of photographs, arms and legs in 3D format is an exclusive art, looking at which you will be illuminated with a smile every time.

It is very popular today to bring such gifts to christenings or buy a certificate for this service as a gift. After all, when the godson grows up, he will probably remember his godparents with gratitude. What else can you give to your godson? Read the article:. Parents can also order hand impressions on a Hollywood Walk of Stars style stand. You can make casts of arms and legs yourself, but how? See below.

How to prepare a baby model for “work”?

It is best to carry out work on making casts of arms and legs when the small model is calm. Pick a moment. This could be a dream or watching your favorite cartoons. You can find cartoons by following the link: . There are sleepy children with whom you can do anything in this state. There is an interesting article about a child’s sleep: “Does your child sleep poorly? Looking for possible reasons and find a solution to this problem."

If you decide to carry out the work of making a cast while the child is awake, then be sure to make sure that the baby is in a good mood, he is not hungry and joyful.
Does the baby move his fingers slightly during the impression? It doesn't matter, it won't ruin it final result, since the mass will better get into all the folds and the handle or leg will be more prominent. In this matter, the main thing is calmness; holding someone in a position will not give the desired result.

How to make casts of arms and legs from sand?

The method is quite simple and does not require any special “troubles”. Any mother can cope with this task, even if she is completely unfamiliar with the art of creating sculptures. Such a cast can be made decorated, then in addition to the tools and materials listed below, you will need decorative elements, which can be shells, chains, buttons or small toys.

Required accessories

To work on the cast you will need:

· container, a round tin cookie box is perfect for this idea;
sand, preferably fine;
· alabaster, it is easy to buy at the construction market (store);
·a brush, usual for painting radiators.

Stages of work

1. Pour fine sand into the selected container and level it. It should not be compacted too much.

2. In the center of the prepared sand, make an imprint of your child’s hand or foot. If you want to make a decorated cast, then make decorations around the print from pre-prepared items.

3. Now you need to work on alabaster. Don't forget that this material hardens very quickly, so you need to work quickly. The powder is diluted plain water. The mass needed for work should be like sour cream.

4. After the alabaster is diluted, pour it in a small stream, so as not to spoil the sand mold, into the container. The thickness of the alabaster above the sand should be 2–4 cm.

5. Leave the container for at least 20 minutes. It is advisable to take longer, but if you are “unbearable”, then you can get it.

6. Carefully remove the cast and use a brush to clean off the grains of sand. Next, act as your imagination dictates: paint, decorate, decorate with drawings, write inscriptions.

How to make casts of arms and legs from plasticine?

Such material as plasticine has been familiar to us since childhood. After all, each of us began to create our first “sculptures” from it in kindergarten. If you are going to make casts of your child’s arms and legs from plasticine, then you need to remember the skills you learned in kindergarten.

Required accessories

For work you should prepare the following materials:

plasticine, today the choice of such material is quite wide, children's soft one is best suited;
regular PVA glue (stationery);
gypsum, it can be different: for decoration, construction, medical. You can take any;
if you want to decorate the cast, then decorative elements.

Step-by-step instruction

1. So that the fingerprint is high-quality plasticine It is necessary to knead thoroughly until soft.

2. Make an imprint of a hand or foot with a depth of at least 1.5 cm. If you want, you can make decorative indentations.

3. We put the resulting print in the freezer to set the contours.

4. Prepare plaster. The standard proportion involves 1 cup of powder + 0.5 cups of cold water. Do not forget to prevent the plaster from forming lumps; water should be poured into the plaster, and not vice versa. Pour a small amount of PVA glue into the resulting mixture.

5. Remove the print from freezer and fill all cavities with plaster.

6. Leave the impression to harden for 12–18 hours.

7. Plasticine can be removed quite easily if you hold it over warm air (battery, boiling kettle) for several minutes.

8. The resulting cast is polished and decorated according to your wishes.

How to make casts of arms and legs from salt dough?

Casts of arms and legs made from salt dough are the easiest way to capture baby's fingerprints. But it should be remembered that the dough is a short-lived product and varnish applied on top in several layers will help preserve the original appearance of the cast.

Required accessories

To prepare the dough for work you need to have:

·wheat flour;
· salt, it is better to choose fine salt;
water.

Step-by-step execution

1. Prepare the dough, it should be elastic. To do this, mix one glass of flour with the same amount of fine salt. Add half a glass of water to the resulting mixture and knead the dough. If you see that there is not enough water, then add a little.

2. Roll out the resulting dough into a 3-5 cm flat cake. You can give the cast a different shape.

3. Push the child’s hand or foot onto the cake. This material is good because if you don’t get the desired result the first time, you can roll out the dough again.

4. Around the print you can write inscriptions, draw patterns or beautiful designs.

5. Place the impression with the imprint in a hot oven for two hours. Optimal temperature for the dough to dry it should be 100–120 degrees. Depending on the thickness of the cake, the baking time also depends.

6. After baking (drying) the cast of the hand or foot, let it sit for a day and only then apply decorative coating(varnish, paint, etc.), decorate with drawings and inscriptions.

Design options for impressions

Making a cast of the arm and leg is half the battle. It still needs to be beautifully decorated. In addition to making a cast, it also needs to be beautifully designed. There are many design options, because it all depends on your imagination. Here are some design options:

1. In the form of a figurine. To do this, cover the resulting cast with silver or bronze spray paint and place it on the base. Sign and date the base and receive a miniature figurine.

2. Photo frame with a cast. Glue in regular photo a framed photo of your child and a cast of a hand and foot. In addition to these things, you can put a tag from the maternity hospital, a pacifier and other paraphernalia of the newborn “under glass”.

3. In the form of a pendant. Make a hole during making. After the casts of the arms and legs have hardened, thread a beautiful ribbon through this hole and hang it on the wall in the children's room. You can read about decorating a room for a newborn in the article:.

Author of the publication: Zoya Kiseleva

Alena Usenko

Currently, many parents make casts of children's hands and feet with their own hands. This commemorative print looks very nice and will allow long years remember the wonderful moments of early childhood.

DIY casts of children's hands and feet

Step 1: Mix mold powder with water. The result is a paste, which must be transferred to a container where the impression will be made. You need to place an arm or leg into the mass. The paste will begin to harden and take White color. Then, you should wait for approximately one minute for the mixture to completely harden if the water is used at room temperature;
Step 2. Move your arm or leg to make it slide out of the mold;
Step 3. Mix the plaster with water, making sure there are no lumps. Pour the mixture into the mold. Leave the imprint for a while so that the plaster hardens;
Step 4: Tear or cut off pieces of the mold to release the cast;
Step 5. After drying, paint the cast in the chosen color or varnish. If you purchased a set with a frame or stand, glue it in place.

To make casts of arms and legs with your own hands, you don’t need experience, you just need to carefully read the instructions. As a rule, sets contain everything necessary materials and tools. In addition, they often provide the opportunity to make several casts, because working with a child is completely unpredictable, and whether the perfect contour will turn out depends largely on our small models.

How to prepare for making a three-dimensional cast of arms and legs with your own hands:

take care of good mood small model;
you can use sleep time;
Residue from the mixture after making may be difficult to wash off, so wear clothes that you don’t mind getting dirty;
the participation of two adults is necessary - one to take care of mixing the ingredients, the second to hold the baby and distract him;
if you have touched the sides or bottom of the mold, you can pour plaster into it and then smooth out any imperfections with sandpaper;
the time it takes for the mold to completely harden depends on the temperature of the water used - than colder water, the longer it will harden, the warmer the water, the faster the material will harden, room temperature water is optimal;
Make sure the containers are the right size for your baby's feet or hands.

How to prepare a child to make a cast of children's hands and feet with your own hands

Take advantage of the moment when little models are calm, this could be a moment of sleep or watching a cartoon. Some sleepyheads can sleep through all the fun and don't even notice what's happening around them.

However, if the child is sensitive to cold, it is important to wet the hands or feet with water first so that the baby has a chance to get used to the temperature of the mass.

If this doesn't help, you can add warm water, but keep in mind that the higher the temperature, the faster the mixture will harden.

In this case, you can add a little more water than indicated in the instructions or fill in not the entire contents of the bag.

If you want to make a mold for casting while the child is awake, you must find a moment when the baby is in a good mood, calm, well-fed and well-rested. Provide an attractive toy, book, or other entertainment to distract your baby.

Don't worry if your little one moves his fingers a little, this will have a positive effect on the final result, allowing air bubbles to escape while allowing the mixture to get into the gaps between the fingers. If your child moves his hand, try gently moving the container behind his hand. Of course, you can hold the handle gently, but remember to remain calm and not forcefully hold your baby. Otherwise, the baby will receive unnecessary stress, and the quality of the impression will be reduced. The mass hardens quickly, so just wait a little and everything will be ready.

Some children do not like it when their leg or arm is immobilized, then you can add less water, which will speed up the drying time. If the child reacts poorly to the moment the arm or leg is immersed in the mass, it is recommended to wait a while. for example, 2 weeks, and try again.

How to prepare molds for casting casts for children with your own hands

To make an impression with your own hands, mix the mold powder with water in any container and pour into a closed container. Plastic container, you can mix the mixture directly in the same container. Measure ingredients accurately as poor ratios can affect the final result. You can use a test sample, which is sometimes included with the kit, to have information about the curing process.

Wet the skin of children's feet or hands thoroughly so that they slide out of the hardened mold easily.

Thanks to this manipulation, your child will be able to get used to the temperature of the mass, in addition, we will minimize the risk of air bubbles that worsen the quality of the product. Guide your baby's hand so that it slides accurately and accurately into the prepared paste.

Don't worry if your baby moves his arm. The beginning of the hardening process will show a change in the color of the paste, and this is the moment at which the child should not make very sudden movements. After hardening (about 1-1.5 minutes), remove the handle. To avoid holes in the set mold, guide your child's hand without touching the bottom or sides of the container.

How to prepare and pour plaster

Pouring plaster should not last longer than 5-6 minutes.

Prepare a plastic bowl and measure required quantity water and gypsum in appropriate proportions. Always add powder to water, not the other way around;
Pour the plaster of Paris into the water slowly, stirring constantly, until the mixture reaches the consistency of very thin yogurt. Mixing too intensively and for a long time can lead to the mass beginning to harden already during pouring into the mold. Also, stirring too much can cause bubbles to form. If you see bubbles on the surface, tap the container a few times to release them;
Initially the plaster is very watery, but after a while it gently begins to thicken. The plaster is ready when it reaches the consistency of pancake batter. Then, pour a small amount of plaster into the mold and carefully move the container in different directions so that the mass fills exactly every hole;
After filling the form 1/3, tap the container on the table surface;
Pour in the rest of the mixture in batches;
Leave the container to harden for several hours.

How to avoid air bubbles in plaster?

Air bubbles spoil volumetric impressions; as a result, the plaster does not reach the fingertips, and the impression will not completely replicate the child’s hand. This problem mainly occurs with hand impressions, since the fingers on them are longer than on the feet, and the plaster does not always flow well into these holes.

You can use the following methods to avoid this:

mix gypsum mixture not too long;
vigorously and repeatedly tap the container with plaster on the table;
puncture large bubbles that appear on the surface;
first pour a small amount of plaster and move it in different directions so that it spreads evenly throughout the entire form;
pour the mixture along the walls, holding the container with the mold at an angle - if the mold is in vertical position, and you pour from above, there is a risk that the mass will not fill the holes to your fingertips;
in the case of legs, if you fill half the mold, you can take a brush and use it to spread the mass;
For handles, you should tilt the mold with your fingers down so that the mass flows there.

In what position is it most convenient to make 3D impressions?

0-5 months. For very young children, the procedure should be carried out in a supine position, as for feeding.

The most beautiful phenomenon created by nature is the birth of a child.

IN modern world with help various types equipment (camera, video camera) you can track the baby’s development from the very first day of life.

But many people want to look at their baby not only from photographs and videos. Therefore, they often order from studios so-called copies of the child’s arms and legs - casts, which can be made from almost any hardening material - plaster, chocolate, wax, liquid glass and other materials.

But in this article we will focus on other types of impressions - the so-called 3D impressions. In another way they are also called volumetric.

On the Internet you can find the technology for their manufacture, but rarely do you see information about them. component composition. In this publication we will reveal this secret to you.

So, to make a three-dimensional cast of a child’s hand or foot, we will need:

- gypsum (or other hardening material)

- alginate (sold in dental stores)

— plastic container

- water (36.6 degrees)

Before you start work, you need to put your baby to sleep in a crib or cradle (if the toddler is still small). This is necessary so that he does not move his arm or leg while taking the impression.

Then we prepare the impression mass. To do this, select the required amount of alginate powder and water in accordance with 1.5 to 1.

Pour the alginate into the water (and not vice versa!) and stir with a mixer or spoon. You just need to do this very quickly, as it hardens almost immediately.

Then we immerse the baby’s hand (leg) in this mass and wait for it to harden. You can check whether it has frozen or not with your finger - touch the surface of the mass - if it does not stick to your hands, then the solidification has ended. As a result, it should feel like rubber.

Now, very carefully, so as not to damage the impression mass, we remove the child’s limb from it and put it back to sleep under the supervision of a baby monitor or video baby monitor. We will get a kind of deepening.

The next step is to prepare a solution of gypsum and water. Pour the plaster into the water (and not the other way around!) and stir it until it reaches the consistency of thick sour cream and fill the resulting cast with this solution. We wait a day. Then carefully use a knife to cut the alginate along the edges of the container, turn it over and make an incision in the mass to pull out the resulting cast.

That's all. As they say, everything ingenious is simple. Now your baby’s three-dimensional cast will be preserved for life and will constantly remind you of the moments of his childhood.

The Chameleon company invites you to try yourself in an interesting business: Making compositions with casts of baby’s hands and feet, 3D copies of newlyweds’ hands, commemorative medals with handprints, casts of pets’ paws.

What it looks like:

Formats

You can run this business at home or open a location in a large shopping center, offering a wider range of services.

"Home" format

If you work from home, orders are accepted as follows. The client calls on the phone. The time and date of the specialist’s arrival at your home are discussed. At the appointed time, the necessary impressions are taken at the client’s home, photographs of the baby are taken, and design options are discussed. All conditions are written down on the order form. It also reflects the amount of the advance payment for the composition and issues a sales receipt. The master takes away the casts and carries out all the rest of the work on filling and further design of the composition at home.

The finished work is delivered to the client’s home or he picks it up himself at the place specified by the master, and, if necessary, pays the remaining amount.

Studio format

If you work in a studio or have retail space in a shopping center, orders are accepted on site by the manager or by phone. Impressions can be taken both in the studio and at the customer’s home, at his discretion. The advantage of going to the client’s home is that such conditions are more comfortable for the baby, with familiar toys and surroundings nearby.

As you can see, the business is quite simple, it does not require special knowledge, significant investments, you only need desire, and in everything else we will help you, from technology to consultations on business management.

The target audience

Potential buyers are: loving parents, grandparents, God-parents. Families with average and above average income. The age of the main client is from 23-45 years.

Promotion methods

The target audience is informed about this service by placing advertisements in: maternity hospitals, kindergartens (nurseries), photo salons and photo studios, children's goods stores, registry offices. The main thing in this business is to make yourself known at the beginning of work through advertising in the above-mentioned places, placing ready-made sample compositions in crowded places potential clients. In the future, word of mouth has a good effect.

Key Features

The main features and advantages are:

lack of license and special permits
minimum investment
high profitability
quick payback
opportunity to show your creativity
Great part-time job for moms on maternity leave
It is not necessary to have an office; you can work from home
There is practically no seasonality

Technology

The technology for making impressions of handles is quite simple.

A very plastic, soft, reusable material is used, which allows even the smallest children to take impressions from birth.
The process of taking an impression takes several minutes. After which the master takes away the casts and fills them with gypsum solution at the workplace; after the gypsum has hardened, the product is processed, if there are defects, and left to dry further.
While the impressions are drying, you can process the photo in the program.
Next, the composition is assembled - all the elements are glued to the base and inserted into the frame.

The time required for the production of one fully designed composition is: 1 day, of which 12 hours for drying the casts ( this process can be speeded up by drying the casts in the oven), immediately going to the client, processing the photo and printing it.

What equipment is required to start this business?

Basic equipment

No special equipment is required, and what is listed is already in almost every home.

A printer is not necessary in this case, because

Printing large format photographs for compositions is in any case carried out in a photo studio.

Required for work plastic containers in the form of disposable plates for taking impressions, 1.5-3 liter containers for 3D copies of hands, a mixer or a spoon for kneading.

How much money do you need to start?

Capital equipment: 25,000
Accessories: no
Purchase of raw materials and Supplies 1,500 rub.
Purchasing a business package - from RUB 5,300.
Costs for an advertising campaign - from 3,000 rubles.
Total: 34,800 rub.

How much can you earn from this?

The cost of making one impression using reusable material is 10 rubles, including plaster and paint.

Frame frame with glass (framing workshop) - 500 rub.

We create casts of arms and legs ourselves using alginate gel and plaster

and higher, depending on the baguette option

Composition design:

photo collage and decorative elements - 100 rubles.
decoration for a frame without glass - 100-200 rubles.

The total cost of the composition is 600-700 rubles.

Retail price

The price of a 30x40 format composition with two children's casts is 2,000-5,000 rubles.

As a result, the income from one composition is 1300 - 3500 rubles.

In practice, for a city with a population of 150 thousand people, the average number of orders per month is 20 pieces, i.e. net profit is about 30 -35,000 rubles. (assuming you run your business from home). Return on investment: 1.5 -2 months

Offer from the Chameleon company

By purchasing a business package from us, you get at your disposal detailed guide to create your own impression business, in which we pass on all our experience and knowledge to you.

Depending on the type of business package, you receive a set of materials and a personal website for starting your new business.

Plus, you will be provided with free consulting support on all management issues. of this business and without time limits.

Update December 2015

Another option for opening a studio for making casts of arms and legs is offered by the company "Present Day" (investments from 30,000 rubles). You can familiarize yourself with the terms of the franchise or leave a request below detailed information about the proposed business model.

Contact details

Chameleon Company
mob. 8 913 792 7363, 906 965 6423
Skype: chameleon2108
Email: [email protected]

Questions and answers on the topic

View all (1)

We make casts of children's hands and feet with our own hands!

Home — Articles — We make casts of children’s hands and feet with our own hands!

Hello dear readers, I’m finally ready for a new article!
It's been a year and a half since my last inspiration!
A lot of new things have happened in my life, the most important thing is that my son, Leonid, was born (in January 2014), my second child!
Now he is already 6.5 months old. And I started working with casts again!

How to make a cast of a hand and foot with your own hands from plaster? We answer: “Very simple!”

There are a lot of kits for making them in stores, and there are a lot on the Internet. different advice how to do it!

In 2011, 3 years ago, when I was making casts of Danochka’s hand and legs, I first bought a ready-made set.

How to make a 3D cast of a child's hand and feet at home

I did everything according to the instructions. I mixed the mixture, put the sleeping child’s hand into the plate, and my Danulya took it and woke up and threw all this liquid over me! While I was washing myself, the second jar of gel dried out. Bottom line: I wasted my money!

Then I went to my favorite Internet and saw many recipes for making children’s casts from plaster.

I want to tell you the simplest and most easy way making casts of my favorite arms and legs, which I liked the most!

To make children's casts you will need:

For the test:
- half a glass of water,
- two tablespoons of sunflower oil,
(butter is needed to make the dough more elastic)
- one glass of flour,
- one glass of salt
(preferably fine, salt is needed to make the dough “obedient” so that it holds its shape better)

The volume of my glass is 150 milliliters.

To make the casts themselves:
- plaster,
- water.

Where can I get plaster for making children's casts?

1. Can be purchased at construction market.
2. You can buy any children's creativity set, for example, the “Sculptor” set.
I still have this set from 2011 :)

First we make the dough.
Mix salt and flour in a plate, add oil and water, mix everything.
The dough should be dense! If the dough turns out liquid, add more flour.
Divide the dough in half and roll it out with your hands.
You need to get two small round but thick (2-3 cm) cakes so that the cast is more voluminous.

We take the little one and make footprints and handprints!

Making a print of a child's foot

Making a child's handprint

The first time with Dana I made the right arm and left leg.
The second time with Leonid, I made the right arm and right leg.
It's better to do it like the first time, for example, left hand and the right leg or vice versa.
I think it looks prettier this way!

Next, take a disposable glass, pour water, add plaster and mix everything.
I don’t specifically write the proportions of water and plaster, since I made the liquid plaster “by eye.”
The consistency should be like sour cream or kefir.

We pour liquid plaster into our children's prints and wait.

When the plaster has hardened, remove the dough and our casts are ready!

The remaining dough can be easily removed with ordinary water.
Children's casts are ready!

All that's left is to decorate them!

You can color the casts however you like, I used pink and silver nail polish!
First I painted the children's casts with pink and then with silver varnish.
This is what happened.

Next, I found a beautiful frame on the Internet, added a photo of the child and signed the age - I printed the photo!
I bought a regular photo frame, included a photo, a pregnancy test, a bracelet and a tag from the maternity hospital!
I glued the finished children's casts onto the glass with double-sided tape!

So a beautiful frame with children's casts is ready for a long memory!

You can add baby's first clothes, pacifier and much more.

For comparison, I’m posting a photo of my first frame with casts!

Now we have this beauty at home:

Children's casts can be made at any age, but to make it easier to attach them, it is better when they are still tiny.
The sooner you make your impressions, the easier it is to attach them to the photo frame!

Happy creations!

P.S. : The only thing I still don’t understand is how to remove air bubbles from the plaster?
There are small dots on the casts.
Maybe you need to stir longer?!

The most beautiful phenomenon created by nature is the birth of a child. Every mother strives to preserve in her memory those happy moments spent with her baby, his every movement, his smile, the first words “mom”, “dad”...

In the modern world, with the help of various types of technology (camera, video camera), you can track the development of a baby from the very first day of life.

But in this article we will focus on other types of casts - the so-called 3D casts. In another way they are also called volumetric.

On the Internet you can find the technology for their manufacture, but you rarely see information about their component composition. In this publication we will reveal this secret to you.

So, to make a three-dimensional cast of a child’s hand or foot, we will need:

Gypsum (or other hardening material)

Alginate (sold in dental stores)

Plastic containers

Water (36.6 degrees)

Before you start work, you need to put your child to bed in or (if the toddler is still small). This is necessary so that he does not move his arm or leg while taking the impression.

Then we prepare the impression mass. To do this, select the required amount of alginate powder and water in accordance with 1.5 to 1.

Pour the alginate into the water (and not vice versa!) and stir with a mixer or spoon. You just need to do this very quickly, as it hardens almost immediately.

Now, very carefully, so as not to damage the impression mass, we remove the child’s limb from it, and put him back to sleep under supervision or. We will get a kind of deepening.

That's all. As they say, everything ingenious is simple. Now your baby’s three-dimensional cast will be preserved for life and will constantly remind you of the moments of his childhood.