Vetonit vh color white. Weber-Vetonit putty for leveling walls and ceilings. Recommendations and precautions when using Vetonit VH cement putty

Modern products Vetonit VH used successfully for thin-layer and final leveling already pre-prepared and plastered bases of facades, ceilings inside the premises themselves, puttying the walls to an excellent level immediately before further painting. This applies to wet, damp and even wet areas.
Various facades can be processed modern buildings, also houses and other buildings where modern and high-quality puttying of the most different surfaces with rather difficult conditions. This applies to various unfavorable climatic conditions. The most suitable foundations are walls made of special expanded clay concrete blocks, modern brick walls, also treated concrete and other surfaces that are directly impregnated with a special primer, leveling out all plaster errors and, accordingly, finishing leveling of certain wall bases and various ceilings.

Where this product cannot be used

Scope of use Vetonit VH (Vetonit VH) quite wide. Special attention It should be noted that this putty is not used to perform work on all surfaces that were previously plastered with special water-soluble dry mixtures. It is also not yet used for direct application to those surfaces that are treated with limestone or cement mixtures. You should not apply Vetonit VH (Vetonit VH) for leveling floors.

Surface preparation

Such a surface should always be dust-free and clean. Any substances that weaken adhesion must be removed. This is dust, grease, dirt and so on. We protect windows and other surfaces that are not treated well.

Mixing of these products

Bag Vetonit VH (Vetonit VH) always mixed with 9 liters of water. Mixing is tedious to do with a drill with an attachment for about 4-6 minutes. In order for the mixture to dissolve well, you also need to let it sit for about 12 minutes. The mortar mixture is completely suitable for immediate use within three hours.
The average drying time for this mixture reaches seven days. In fairly cold conditions, the process of so-called strength gain is somewhat increased. Absolutely all this needs to be taken into account.
The average temperature of such a mixture should be no higher than +10 degrees. The working tool is washed immediately after use. Do not pour the remaining mixture down the drain.
you can buy Vetonit VH (Vetonit VH) in specialized stores. The selection of goods there is quite large and varied. In addition, you can also purchase goods in online stores. You can buy the mixture in bulk. In this case, you won’t even have to overpay. After all, wholesale prices are always much lower than retail prices.

Vetonit VH (Vetonit VH) quite popular among buyers. Because the price for it is not too high, but specifications pretty good.

If you want to purchase modern Vetonit VX at retail, you need to study all offers carefully. Since many companies offer discounts to customers. Good luck.

Peculiarities:

• Moisture resistant.
• Highly durable.

Suitable bases:

Specifications:

Preparing the base:

Preparation of the mixture:

Application:

Drying time:

Goods ordered in the OBI online store are delivered throughout Moscow and the Moscow region within 50 km from the Moscow Ring Road. Delivery costs are automatically calculated when placing an online order, based on the weight of the product and delivery area.

Minimum order amount for free delivery:

We will deliver your order free of charge if the delivery address is located in the first delivery zone for online orders, and also:

• > 5,000.00 RUR- for orders weighing up to 5.0 kg
• > 10,000.00 RUR- for orders weighing up to 30.0 kg

The courier service delivers small-sized orders (weighing up to 30 kg) to the buyer’s door, large-sized ones - to the entrance (wicket, gate) of the house. Delivery includes free unloading of goods from the vehicle and their transfer within 10 m.

Delivery date and time

Next day delivery is available when ordering before 6:00 pm. You will be offered a choice of one of two 7-hour delivery intervals:

• - from 10:00 to 16:00
• - from 15:00 to 22:00

If you want to reduce the waiting period, you can choose one of the 3-hour delivery intervals for an additional fee:

• - from 10:00 to 13:00 +350.00 ₽.
• - from 13:00 to 16:00 +300.00 ₽.
• - from 16:00 to 19:00 +300.00 ₽.
• - from 19:00 to 22:00 +350.00 ₽.

Rescheduling the date and changing the delivery time interval is possible no later than 24 hours before the previously agreed date and time.

You can find out more about the working conditions of the courier service in the section

Finishing cement putty white weber.vetonit VH used for final leveling of walls and ceilings before painting, wallpapering or ceramic tiles in dry, damp, wet rooms. The mixture is used not only for interior work, but also for finishing leveling plaster facade before painting.

Finishing putties on cement based are an ideal material for sealing shallow cracks and irregularities. This mixture can be used for outdoor work, because cement putty is moisture-resistant, frost-resistant, and also resistant to sudden changes temperature.

Grain quartz sand putty is no more than 0.3 mm, so the putty surface is smooth and uniform.

ADVANTAGES:

• Universal: perfect solution for all types of premises, as well as for facades;
• Convenient: maximum homogeneous mixture with finely ground filler 0.3 mm;
• Easy: super flexible application of thin layers of 1-3 mm;
• Ideal: absolutely smooth and white surface;
• Reliable: high strength and frost resistance;
• Technologically: for manual and mechanized use.

weber.vetonit VH Suitable for the following substrates:

• Surfaces treated with cement and cement-lime plasters;
• Plasterboard sheets;
• Concrete;
• Lightweight concrete;
• Expanded clay concrete blocks and bricks.

putty weber.vetonit VH has excellent adhesion and does not crack after drying. Recommended application layer is from 1 to 3 mm. Depending on the thickness of the layer, the drying time of the putty varies from 1 to 2 days. To apply subsequent layers, you must wait until the previous layer has completely dried.

Application of weber.vetonit VH

Instructions for use

Preparing the base:

The base must be clean, hard and durable. Windows and other untreated surfaces must be carefully protected. Substances that weaken adhesion such as grease, dust, etc. must be removed. The temperature of the base and mortar mixture must be at least +10°C.

Preparation of the mixture:

• Gradually pour a bag (5 kg) of dry mixture into a container with 1.6 - 1.8 liters of water, stirring at the same time. Recommended water temperature + 20 °C.
• Mixing is carried out using a drill with an attachment for 3-5 minutes. Let the solution sit for 10 minutes. After this, stir the mixture again before use.
• The time for using the finished mixture is 3 hours from the moment of mixing with water.

Application:

Apply the mixture manually using a steel spatula or spray mechanized way. The previous layer of putty must dry before applying the next layer. Grind the working seams and surface after the mixture has dried sufficiently after 1-2 days. The putty reaches its final strength within 4 weeks. In dry conditions, to ensure the necessary hardening conditions, the leveled surface is moistened with water.

The dried surface can be left without further treatment or covered with alkali-resistant paint, wallpapered or tiled.

Weber.vetonit VH putty is not suitable for leveling substrates treated with mixtures based on a polymer binder, for leveling floors and substrates treated with lime plaster solutions.

Cleaning the instrument

Cleaning of hands, tools and containers must be done immediately after completion of work.

Precautionary measures

• When working, you must use rubber gloves;
• Avoid prolonged contact with skin and eyes;
• Avoid inhaling dust;
• In case of contact with eyes, rinse big amount water;
• Keep away from children.

Disposal instructions

The dry mixture and hardened material must be disposed of as construction waste. Dispose of the paper bag as regular waste.

Putty finishing Weber Vetonit VH ( Weber Vetonit VX)

DESCRIPTION:
Waterproof, white, cement-based finishing putty for leveling walls and ceilings indoors, as well as for facades

PROPERTIES:
- layer thickness 1-4 mm

- white surface
- preparing the base for painting and wallpapering
- leveling the base before applying the sticker ceramic tiles

PURPOSE:
- Leveling walls and ceilings in dry, damp and wet areas before:
wallpaper sticker,
- painting and leveling the walls before:
ceramic tile sticker
- as well as for fine leveling of plastered surfaces of facades before painting.

ADVANTAGES:
- For interior and exterior use
- white, smooth surface
- manual and mechanized application

BASE PREPARATION:
The base must be solid, clean, free from dust and dirt. Substances that weaken adhesion such as grease, dust, etc. must be removed. If necessary, dry and absorbent surfaces are moistened. Windows and other untreated surfaces must be carefully protected.

PREPARATION OF THE MIXTURE:
Pour into a container of 8-9 liters clean water and fill in 25 kg (bag) of the weber.vetonit VH mixture, and the mixture must be added to the water, and not vice versa.
Recommended water temperature is 20°C. Mixing is done with a powerful drill with an attachment for 3-5 minutes.
To better dissolve the binder, the mixture is allowed to stand for 10 minutes. After light re-stirring, the mixture is ready for use.
The mortar mixture is suitable for use within 3 hours from the moment of mixing with water. The temperature of the mortar mixture should be in the range from +10 to 30° C.

APPLICATION:
The mortar mixture is applied by mechanical spraying or manually and leveled using a steel spatula. For complete leveling, use a two-handed steel spatula 80 cm wide, and for partial leveling, use a small one, 30 cm wide. When leveling in several layers, it is necessary to apply each subsequent layer on the completely dry previous one (after 1-2 days). The dried surface of the putty must be treated with sanding paper and removed from dust before applying the next layer. When leveling the surfaces of facades, it is recommended to apply the mortar mixture in 2 layers. The first layer is partial leveling and filling of pores. The second layer is to completely level the surface.
In dry conditions, to ensure the necessary hardening conditions, the leveled surface is moistened with water using a sprayer. After sanding, the leveled and dried surface can be painted with alkali-resistant (cement-resistant) paint, wallpapered or tiled, having previously removed dust from the surface after sanding. To increase the wear resistance of the material and improve adhesion, you can replace 10% of the mixing water with weber.vetonit MD16. When leveling old painted surfaces, you can use weber.vetonit RF tile adhesive or base layer done with weber.vetonit 410 mortar. Facade surfaces can be painted facade paints weber.vetonit420 and weber.ton micro V.

DRYING TIME:
The drying time of one layer of recommended thickness is 1-2 days with good ventilation. Drying time depends on layer thickness, ventilation and temperature.
A level of 50% of the final strength is achieved within 7 days at 20°C; as the temperature decreases, the process of strength gain slows down.

SPECIFICATIONS:
Color white, gray
Cement binder
Limestone aggregate
Maximum fraction, mm 0.3
Mixture consumption kg/m2/mm 1.2
Water consumption, l/kg 0.32-0.36
Water consumption, l/25 kg bag 8-9
Layer thickness, one application, mm 1-4
Application temperature, °C +10° to +30° C
Time of use from the moment of mixing with water, hours 3
Drying time (one layer), 1-2 days
Strength of adhesion to concrete after 28 days, MPa, not less than 0.5
Compressive strength after 28 days, relative humidity 50%, +23°C, MPa 6-8
Gain 50% strength within 7 days

PRECAUTIONARY MEASURES:
When working, you must use rubber gloves, avoid contact with skin and eyes, in case of contact with eyes, rinse with plenty of water, keep away from children.

DISPOSAL INSTRUCTIONS
The dry mixture and hardened material must be disposed of as construction waste. The material must not be discharged into the sewer.
Dispose of the paper bag as regular waste.

PACKING:
Paper bag 25 and 5 kg

STORAGE:
12 months from the date of manufacture, provided that it is stored in original packaging in a dry place.