Basic tile adhesive. OK-Basic. Application layer thickness

Before laying the tiles, the mortar should be properly prepared. To do this, you need to dilute 1 kg of dry mixture in 0.20-0.24 liters of tap water (for 1 25 kg bag - 5-6 liters of water). Mixing should be done manually or mechanized way(with a drill with an attachment), evenly pouring the dry mixture into the water until a homogeneous paste-like mass is obtained. laying, leave the solution for 5-10 minutes, then mix it again. The solution is in working condition for at least 3 hours. It is recommended to carry out work at a temperature of +20C.

Surface preparation.

Tiles should only be laid on a clean and hard surface. Before the tiles are laid on the base, dust and grease contamination should be removed, the glossy surface should be sanded, and significant unevenness should be leveled with putty. BOLARS leveling white or BOLARS Waterproof white putty, or BOLARS Facade putty white. It is recommended to treat the surface with a penetrating primer BOLARS acrylic.

Application for tiles.

The glue is applied with a smooth spatula and then leveled with a serrated one. The tiles are laid within 15-20 minutes after applying the mixture to the base. The tiles are leveled within 10 minutes. The tiles should be laid at air temperatures from +5 C to +30 C. Drying time is 24 hours. Full strength is achieved after 3 days. The working life of the solution is at least 3 hours. Grouting - after 48-72 hours.

Kreps base glue - Kreps company

Adhesive mixture for ceramic tiles.

Manufactured in accordance with TU 5745-030-56852407-09.

With BOLARS materials, laying tiles will become much easier. Mosaic, tile and ceramic tiles will be securely fixed to the surface or floor.

Price-sale-buy Kreps basic tile adhesive, 25 kg wholesale and retail. construction yard-tyumen

Purpose

Tile adhesive on cement based CREPS BASIC is intended for laying facing materials on generally accepted foundations in construction:

• cement and cement-lime plasters;
• concrete and reinforced concrete foundations.

Used for tiling walls and floors with ceramic tiles.

Preparing the base

The substrate must be level, strong, hard and free of dust, dirt, old paint residues, oil stains and loose particles. The base must be sufficiently dry and seasoned and must not be subject to deformation or shrinkage. Operating temperature of base, solution and environment should be no lower than 5°C and no higher than 25°C.

Preparation of the solution

Material consumption: 2-4 kg of dry mixture per 1 m2 of surface. The glue consumption in practice depends on the degree of evenness of the base and the type of ceramic used. The dry composition is mixed with clean water room temperature until a homogeneous mass is obtained in the ratio: 25 kg of dry mixture per 5-5.5 liters of water and kept for 5-10 minutes. Then mix again for 30 seconds, after which the solution is ready for use.

Attention! Use only clean containers and tools for mixing. The mixture is poured into the water, and not vice versa!

Application

The resulting solution is suitable for use within 4 hours after preparation. The glue is applied to the surface with a notched trowel. The tiles are laid in such a way that the seams are filled no more than halfway. The recommended seam width is at least 2 mm. When laying tiles big size It is recommended to apply glue to the back side of the tile. Excess glue is removed and, after mixing, used again. When facing, select the correct size of trowel teeth. For example, for tiles measuring 15x15 cm, the tooth size should be 6 mm, and for tiles 30x30 cm - 8 mm.

Attention! Do not pre-soak the tiles! The tiles should be laid on the mortar applied to the base within 10 minutes, while the mortar is fresh and retains its adhesive properties. Correction time for glued tiles is 10 minutes. Grouting should be done no earlier than 48 hours after laying the tiles.

Cleaning the instrument

Tools and equipment are cleaned with water immediately after completion of work. The water used to clean the instrument cannot be used to prepare a new mixture.

Safety precautions

When working with the composition, use individual means protections that prevent the mixture from entering Airways and on the skin. If particles of the mixture get into your eyes, rinse them with water and, if necessary, consult a doctor. Keep out of reach of children.

Packaging and storage

Supplied in 25 kg bags. Shelf life: 6 months in unopened packaging in a dry place.

Technical data

Fraction Maximum 0.63 mm Material consumption 2-4 kg/m2

25 kg (bag) per ~8 m2 Amount of water per 1 kg of mixture ~0.2 l

per 25 kg of mixture 5-5.5 l Suitability time of the solution for use 4 hours Open working time 10 minutes Tile correction time 10 minutes Adhesion strength to the base at the age of 28 days More than 0.5 MPa Brand strength M50 Resistance to slipping Less than 0.5 mm Use After 72 hours Grouting After 48 hours Application temperature, °C from 5 to 25

Building materials and construction, sale of building materials in St. Petersburg

• For interior and exterior use
• 2 in 1: glues and levels up to 15 mm
• slip resistant
• frost-resistant

Application area

FOBOS PRO tile adhesive is intended for fastening all types of ceramic tiles to vertical and horizontal non-deforming bases in rooms with normal and high humidity. It is allowed to glue porcelain stoneware slabs indoors onto unheated floors with a size of no more than 300x300 mm and with a water absorption of more than 0.5%. It is used for leveling base surfaces with a layer of up to 15 mm, and also as an assembly adhesive for bricks, cement-sand blocks and blocks of cellular concrete(foam-aerated concrete, gas silicate, etc.) during the construction of external and interior walls. Made on a cement-sand base using highly effective modifying additives.

Apply manually on concrete, brick, aerated concrete, plastered surfaces, gypsum plasterboard, gypsum board, gypsum plasterboard.

Preparing the base

The base must be strong, level and have sufficient bearing capacity. Before starting work, the surfaces must be dust-free and cleaned of all types of contaminants that reduce adhesion. finishing materials. Peeling and weak areas must be removed. Irregularities up to 15 mm can be eliminated using FOBOS PRO glue, over 15 mm - with materials from the plaster group. It is recommended to level the floors using a self-leveling floor, depending on the thickness of the applied layer and the level of humidity in the room. Cement and gypsum plasters, floors, highly absorbent substrates (gypsum, lime plasters, cellular concrete, brickwork, plasterboard, gypsum fiber boards), plasters must be treated with primer. Poorly absorbent surfaces ( monolithic concrete, paint coatings, etc.) are treated with Betonokontakt primer. The tiles are fastened after the soil has completely dried.

Description

BASIC CREPS - dry mortar, consisting of cement, fine-grained fractionated sand, modified special additives. After mixing with water it forms a plastic mortar mixture. It is water and frost resistant.
Purpose
KREPS BASIC is intended for laying ceramic tiles for interior and exterior work on bases generally accepted in construction:
. cement, cement-lime plasters, including KREPS MASTER and KREPS PROFI;
. concrete and reinforced concrete bases, provided that they are dry and seasoned.
Used for cladding walls and floors.

Preparing the base
The base must be level, strong and not subject to shrinkage or deformation. If necessary, the base must be cleaned of dust, dirt, oils, grease, bituminous substances, etc. It is recommended to prime the base with KREPS PRIMER.

Preparation of the solution
Pour 5-5.5 l into a 25 - 30 l container clean water room temperature and pour 25 kg (bag) of adhesive composition into it. Mix mechanically until a homogeneous mixture is obtained. Leave the mixture for 10 minutes, then stir again. At 200C, the prepared mixture remains viable for at least 4 hours.

Application
Apply adhesive composition BASIC CREPS on the base. Level with a notched trowel. Lay the tiles. It is necessary to lay the tiles on the freshly applied mortar within 10 minutes until mortar mixture retains its adhesive properties. Tile correction time is 10 minutes.
Grouting should be done no earlier than 48 hours after laying the tiles.
You can walk on the tiled floor no earlier than 72 hours after laying the tiles.
When facing, you should select the correct size of trowel teeth. For tiles measuring 150x150 mm, a tooth size of 6 mm is recommended, and for tiles 300x300 mm - 8 mm.
When tiling with 300x300 mm tiles and in rooms with high pedestrian traffic, it is recommended to apply the adhesive composition to the base and back side of the tile.

Cleaning the instrument
Tools and equipment are cleaned with water immediately after completion of work.
The water used to clean the instrument cannot be used to prepare a new mixture.

Safety precautions
When working with the composition, use personal protective equipment to prevent the mixture from entering the respiratory tract and on the skin. If particles of the mixture get into your eyes, rinse them with water and, if necessary, consult a doctor.
Keep out of reach of children.

Packaging and storage
Supplied in 25 kg bags.
Shelf life: 12 months in unopened containers in a dry place.

Peculiarities:
- good adhesion to the base 0.5 MPa;
- high grade strength M50;
- for all types of ceramic tiles;
- viability adhesive solution 4 hours;
- possibility of use in dry, damp and wet rooms;
- shelf life 12 months without loss of properties in closed original packaging in a dry place.

Technical data

Application area:
Designed for fastening all types of ceramic tiles to vertical and horizontal bases in rooms with normal and high humidity. It is used for leveling base surfaces with a layer of up to 15 mm, and also as an assembly adhesive for bricks, cement-sand blocks and blocks made of cellular concrete, foam concrete, gas silicate, etc. during the construction of external and internal walls. Apply manually to concrete, brick, aerated concrete, plastered surfaces.

Material consumption:
3.0-3.5 kg/m² (when applied with a notched trowel with a tooth size of 6x6 mm). 25 kg bag for 7-8 m².

Preparing the base:
Remove adhesion-weakening substances from the base: oil and bitumen stains, dust and other contaminants. Remove peeling areas with a steel spatula. Level the base. Level out depressions, cracks and irregularities up to 15 mm with BOLARS Basic tile adhesive; over 15 mm – plaster compositions BOLARS. Treat the base primers BOLARS, corresponding to your surface type.

Preparation of the solution:
To prepare the solution, pour tap water room temperature into a clean container at the rate of 4.0-5.0 liters of water per 1 bag (25 kg). When pouring the dry mixture into water, mix the solution with a drill with a special attachment at low speed until a homogeneous mass is obtained. Wait 5 minutes, then stir again. The working life of the solution is at least 3 hours.

Execution of work:
Apply glue with a notched trowel. The size of the teeth depends on the size and weight of the tiles being laid. Lay the tiles within 15 minutes after applying the adhesive to the base. Level the tiles within 10 minutes.
It is recommended to carry out work wearing rubber gloves. If the solution gets into your eyes, rinse them immediately big amount water. To protect the respiratory system, use respirators, and to protect the eyes, use safety glasses.

Packing and storage:
Supplied in multi-layer paper bags. Shelf life in a dry place in undamaged original packaging is 12 months.

Specifications:
- color: gray
- consumption when using a spatula with a tooth size of 6x6 mm: 3.0-3.5 kg/m2
- work temperature: +5°С...+30°С
- tile adjustment time: 10 minutes
- layer thickness: 2-15 mm
- frost resistance: at least 50 cycles
- time of suitability of the solution for use: at least 3 hours
- compressive strength: not less than 7.5 MPa
- amount of water per 1 kg of dry mixture: 0.16-0.20 l
- open time: 15 minutes
- rubbing of seams: after 24 hours
- adhesion (tiles with water content > 3% at normal conditions hardening): not less than 0.7 MPa
- operating temperature tile covering: +5°С...+40°С
- operating temperature when laying masonry: -40°С...+60°С