Tile adhesive for any substrate Bergauf maximum. Maximum Plus Adhesive for all types of tiles and any substrates Bergauf maximum plus technical characteristics

Adhesive for tiles and porcelain tiles BERGAUF MAXIMUM PLUS ("Bergauf Maximum Plus") designed for reliable gluing ceramic tiles any size, porcelain tiles for floors and walls indoors and outdoors. Gluing natural stone possible on the floor without restrictions, and on walls with the use of additional fasteners.

BERGAUF MAXIMUM PLUS adhesive is used on deformable and non-deformable substrates, ideal for underfloor heating systems and for laying tiles on tiles. Used in rooms with any level of humidity, including bathrooms, bathtubs and swimming pools. It has proven itself to be excellent for use in exterior work on facades, plinths and balconies.

MAXIMUM PLUS adhesive contains cement binder, fractionated sand, mineral fillers, modifying polymer additives, which ensures reliable fastening and long service life.

Key properties

Consumption

The consumption of BERGAUF MAXIMUM PLUS tile adhesive is about 0.8 - 0.9 kg per 1 m2 with a layer thickness of 1 mm. Allowable thickness The application layer ranges from 3 to 10 mm.

Application

• Apply the prepared mixture with the even edge of a spatula onto the base.
• The adhesive must be applied to an area that can be covered within the next 20 minutes ( open time).
• The applied mixture is leveled with a notched trowel.
• You can adjust the position of the tile within 15 minutes.
• Position the tiles so that the gap with other tiles is at least 1 mm.
• When working with slabs big size, low-absorbent tiles or natural stone, it is necessary to additionally apply glue to back side tiles and also level with a notched trowel.
• When working with particularly heavy slabs, it is recommended to use additional fasteners.
• Remove excess adhesive from the tile surface with a damp sponge before it dries.
• Grout the joints after 12 hours on the walls, and after 24 hours on the floor.
• When laying tiles in a bathroom or swimming pool, it is recommended to begin operation no earlier than 7 days for a bathroom, 28 days for a swimming pool, after completion facing works.

Article No. 3985306

A mixture based on cement binder, fractionated sand, mineral fillers, and modifying polymer additives. Glue mixture for facing walls and floors with ceramic tiles up to 900 sq.cm. For facing floors and walls using additional fasteners with porcelain stoneware, low-absorbent tiles, and natural stone. It is applied for interior work with normal and high humidity(bathroom and swimming pool) and for outdoor work (facade, balcony, basement). Applied to deformable, non-deformable and critical substrates.

Product Features:
Color - gray.
The binder is cement.

Application characteristics:
Consumption of dry mixture per 1 sq.m. with a layer of 3 mm approximately 2.5 kg.
Recommended layer thickness is 3-10 mm.
The viability of the finished solution in an open container is 3 hours.
Open time after application - 20 minutes.
Tile adjustment time - 15 minutes.
Time to fully gain strength is 28 days.
Grouting joints for vertical/for horizontal surfaces allowed after 12 hours/24 hours.
You can walk after 24 hours.
Carrying out work at air and base temperatures from +5 to +25 degrees.

Operating characteristics:
Brand strength - M 150.
Compressive strength (after 28 days) - 15 MPa.
Bending strength (after 28 days) - 2.5 MPa.
The strength of adhesion to the base (after 28 days) is at least 1 MPa.
Operating temperature from -50 to +70 degrees.
Frost resistance - F 50.

Specifications

Common parameters

Adhesive for all types of tiles Bergauf Keramik Maximum is used for walls and floors. Suitable for laying ceramic tiles, large-format tiles, porcelain tiles on non-deformable and deformable substrates. Can be used in the "Warm Floor" system. For interior spaces with normal and high humidity, as well as for outdoor work.

ADVANTAGES:
• Increased elasticity;
• For complex bases;
• Laying "tile on tile";
• Recommended for swimming pools.

Instructions for using Bergauf Keramik Maximum glue

Compound

Cement binder, fractionated sand, mineral fillers, modifying polymer additives.

Preparing the base

The base must comply with the requirements of SNiP 3.04.01-87 and have sufficient load-bearing capacity.

Bergauf Keramik Maximum adhesive is recommended for attaching ceramic, tiles, porcelain stoneware, including large-format, artificial and natural stone, on concrete, cement bases, cellular concrete bases, cement waterproofing coatings, cement, cement-lime plasters and putties, gypsum plasterboard, gypsum fiber board and “warm floors”. The product is recommended for swimming pools, work on balconies, facades and plinths, as well as critical foundations.

When carrying out work on the “Warm Floor” system, it is recommended to turn off the heating at least 2 days before starting work. Turning on the “Warm Floor” is possible after 7 days.

Clean the surface from dirt and dust, peeling old coatings and oil stains - anything that can impair the adhesion of the material to the base. The prepared base must be treated with Bergauf primer (“PRIMER” or “TIEFGRUNT” - depending on the type of base) and dried for 4 hours. Highly absorbent substrates (e.g. cellular concrete) should be primed twice with Bergauf “TIEFGRUNT” primer. We recommend treating concrete, reinforced concrete, other low-absorbent and critical substrates, gypsum board, gypsum board with Bergauf Beton Kontakt and dry for 4 hours.

For unevenness more than 5 mm (up to 15 mm):

If the surface of the base is not primed, the following consequences are possible: reduced open time and low adhesion strength of the tile to the base.

Preparation of the solution

Use clean containers and tools to prepare the solution.

Attention!

The properties of the product are guaranteed only if the proportions of mixing with water and the procedure for preparing the solution are strictly observed.

1. Fill the mixture with water (from +5°C to +25°C) in the following proportion: per 1 kg of mixture - 0.23 - 0.25 l of water; for 25 kg of mixture - 5.75 - 6.25 liters of water.
2. Stir until smooth*.
3. Wait 5 minutes for everything to finish chemical reactions.
4. Stir again.

The prepared solution must be used within 3 hours from the moment of mixing.

Safety precautions

Do not allow material to come into contact with eyes or Airways.

Storage

Guarantee period storage in a dry place and in closed original packaging is 12 months from the date of manufacture.

The manufacturer is not responsible for non-compliance with the technology for working with the material, for its use for purposes and conditions not provided for in these instructions, as well as in the case of the introduction of foreign components and substances into the product.

Operating procedure:

1. Apply the prepared mixture with the even edge of a spatula onto the base. The adhesive must be applied to an area that can be covered within the next 20 minutes (open time).
2. The applied mixture is leveled with a notched trowel***.
3. You can adjust the position of the tile within 15 minutes. Position the tiles so that the gap with other tiles is at least 1 mm. The seam between the tiles can be filled with glue no more than half. The required width of the joints between the tiles is determined based on the size of the tile, operational and aesthetic features.
4. When working with large slabs, low-absorbent tiles or natural stone, it is necessary to additionally apply glue to the back side of the tile and also level it with a notched trowel. For better adhesion, the direction of the grooves of the mixture applied to the tile should be perpendicular to the direction of the grooves on the base. In case of working with particularly heavy slabs, it is recommended to use additional fasteners (screws, dowels, initial profile and tiling from bottom to top)
5. Remove excess adhesive from the tile surface with a damp sponge before it dries. After drying, excess glue can only be removed mechanically.
6. Grouting of joints is allowed 12 hours after fixing the tiles for vertical surfaces and 24 hours for horizontal surfaces. To fill the joints, it is recommended to use Bergauf KITT or Elast Premium grout.
7. When laying tiles in a bathroom or swimming pool, it is recommended to begin operation no earlier than 7 days for a bathroom, 28 days for a swimming pool, after finishing the tiling work.

**The choice of spatula depends on the size of the tile: For tiles with a side up to 10 cm - the size of the spatula tooth is 4 mm; For tiles with a side up to 30 cm - the size of the trowel tooth is 6-8 mm; For tiles with a side up to 60 cm, the trowel tooth size is 8-12 mm.

Attention! Draft, poorly prepared surface, low humidity or elevated temperatures may reduce open time and pot life of the finished mixture.

ADHESIVE FOR ALL TYPES OF TILES AND COMPLEX SUBSTRATES

- elastic
- for complex bases
- tile-on-tile installation
- recommended for swimming pools

Application area

* subject to appropriate surface preparation

Specifications

Compound

Cement binder, fractionated sand, mineral fillers, modifying polymer additives.

Preparing the base

Clean the surface from dirt and dust, peeling old coatings and oil stains - anything that can impair the adhesion of the material to the base. The prepared base must be treated with "Bergauf" primer ("PRIMER" or "TIEFGRUNT" - depending on the type of base).

Preparation of the solution

Attention! The properties of the product are guaranteed only if the proportions of mixing with water and the procedure for preparing the solution are strictly observed.

1. Fill the mixture with water (from +5°C to +25°C) in the following proportions:
   • for 1 kg of mixture - 0.23 - 0.25 l of water;
   • for 25 kg of mixture - 5.75 - 6.25 liters of water.
2. Stir until smooth.
3. Wait 5 minutes for all chemical reactions to complete.
4. Stir again.

Operating procedure

1. Apply the mixture with the even edge of a spatula onto the prepared base. The adhesive must be applied to an area that can be covered within the next 20 minutes (open time).
2. The applied mixture is leveled with a notched trowel.
3. When working with large slabs, low-absorbent tiles or natural stone, it is necessary to additionally apply glue to the back side of the tile and also level it with a notched trowel. For better adhesion, the direction of the grooves of the mixture applied to the tile should be perpendicular to the direction of the grooves on the base. When working with particularly heavy slabs, it is recommended to use additional fasteners.
4. Place the tile against the surface with applied mixture and press with slight force.
5. You can adjust the position of the tile within 15 minutes.
6. Grouting of joints is allowed after 12 hours. When laying tiles in a bathroom or swimming pool, it is recommended to begin operation no earlier than 7 days after finishing the tiling work.

Attention! Drafts, poorly prepared surfaces, low humidity or high temperatures can reduce the open time and pot life of the finished mixture.

Safety precautions

Avoid contact of material with eyes and respiratory tract.

Storage

The guaranteed shelf life in a dry place and in closed original packaging is 12 months from the date of manufacture

For orders up to 100 kg we offer a budget delivery cost (delivery time up to 2 days):

* Drywall, insulation, lumber, profiles for gypsum boards, foam blocks and bricks are calculated from the table from 100 kg.

**Delivery over 15 km, calculation is based on the “tariff” + 50 rubles per 1 km.

For orders of 100 kg or more:

* provided that the ordered goods fit into a passenger car.

** provided that the volume of the ordered goods fits into a truck of the specified tonnage.

Delivery of unsawn 6 meter lumber (boards, timber) with a volume of up to 2 m3 costs from 3 000 rub.

When paying for delivery by bank transfer, 5% is added to the delivery cost.

Additional requirements for a car, for example, a small height for entering a parking lot or an open body for vertical unloading is paid additionally: + 20% of the cost of the standard tariff.

Delivery terms

Whenever possible, goods are delivered on the day you order or on any other day convenient for you.

Cost of unloading and lifting

Table for calculating the cost of unloading orders:

* Prices in the table are based on a working freight elevator, regardless of the floor.

** In the absence of a freight elevator, the cost of the lift is multiplied by the number of floors to the apartment where the goods need to be unloaded.

*** The minimum order cost for unloading and lifting is 500 rub.

Important!

The service "Lifting Material" includes cleaning the entrance, removing garbage and other ensuing consequences after lifting building material, are not included in the price. Prepare in advance for the service you ordered. Thanks for understanding!