You can clean your water cooler. How to clean a water cooler at home. External water cooler cleaning

In this article we will digress a little from regular topics. Probably everyone has already noticed how often we began to use water coolers in the office and at home. A water cooler (dispenser) is a household appliance. And this requires care and cleaning. The latter is recommended to be carried out in accordance with the frequency of use, but not less than once every six months. If a lot of people use the device (office), then it would be logical to reduce this interval to three months, and at home it would be best to reduce it to one month.

The device needs to be cleaned mainly to remove hazardous human body bacteria. It becomes even more polluted due to inattentive and careless attitude towards it during operation.

How to clean the cooler yourself

For the operation you will need:

thin rubber gloves;
cleaning brush;
sponge;
dishwashing liquid;
disinfectant;
supply of clean water in 5-liter bottles.

Preparing for cleaning

Wash your hands and put on gloves. Unplug the machine's power cord from power outlet and wait about a quarter of an hour until the heated water in the cooler tank cools down.
Dilute the disinfectant in the bottle according to the instructions on the label. If the solution somehow gets on the skin, rinse it with running water for a couple of minutes.

The order of sanitary maintenance of the device

1. Draining the rest of the contents

Remove the water tank from the machine. Drain water from it into prepared containers through the water supply taps.
Then remove the remaining water through the drain (usually on the back of the case). By the way, the water may still be hot, be careful!
Close the taps and drain.

2. Rinsing with a brush and sponge

Unscrew the taps from the housing. Carefully and carefully, using a brush and sponge, wipe them from all sides and from the inside with dishwashing liquid. Then rinse thoroughly under running water.
Wash the entire body of the device with this liquid, especially the corner areas.
Screw the taps, each into its own hole, according to their color (red, blue).

3. Washing with disinfectant solution

Unscrew the taps, having previously installed the prepared bottles under them. Carefully pour the disinfectant solution into the recess of the device (a bowl with a needle for the container) until it flows out of the tap.
Make sure there is flow from both faucets. Twist them. Add more disinfectant solution into the cavity.
Do not touch the device with the disinfectant solution during disinfection for at least an hour.
Then drain the solution through the taps and drain hole. Don't forget to tighten them.

4. Rinsing the cooler from disinfectant solution

Unscrew the taps, installing empty bottles in advance. Fill the cup with the needle clean water until it flows from the tap. Check that it is flowing from each tap. Then twist them.
Next, open the drain device and remove any remaining rinsing water. Don't forget to close it.
Attention! The water remaining after rinsing the disinfectant solution should not be drunk.
Carry out the rinsing phase again. In total, the device is washed 3–4 times.

5. Final phase of washing operations

Place a new container (without sticker) with water on the device.
Connect to an outlet. Wait until the water is ready to dispense.
The unit is cleaned and ready for further use!

In fact, the process of cleaning the cooler does not take much time. The main thing is to follow all the instructions in order - and you will succeed!

Cooler is very useful device, used not only in office space but also in many private houses and apartments. However, in order to this tool truly served clean water, it must be cleaned regularly. According to experts, cleaning a water cooler should occur at least once every 3 months. Moreover, it is not necessary to call specialists for this; you can do everything yourself.

Procedure and algorithm of actions

Cleaning the water cooler begins by disconnecting the device from the power supply. Next, it is installed on a special waterproof mat, after which you need to remove the bottle from it and drain the old water. Follow the procedure: first drain the liquid from the hot tap, and then from the cold one. At the next stage, cleaning the water cooler is accompanied by diluting the drained water using a special disinfectant "BIOR 1". Dosage - approximately 25 milliliters per 1 liter of water. Next, you need to apply a special detergent “Kremklin” to those parts that are in the drip tray.

Afterwards, our so-called “repair” of water coolers is carried out by removing the bottle holder (it must be removed along with the needle) and disinfecting the bottom and walls of the tank. To do this, it is not necessary to use any potent or specialized products. It is enough to simply wipe the inner surface of the container. But in the cooling tank it is just the opposite - for disinfection you need to use the prepared solution. We pour it in there and allow some of the hot and cold water from the taps. This is necessary to ensure that the watercourses fill up. the right amount disinfectant solution.

Now the water cooler will be cleaned with brushes and brushes. They need to be processed inner part holder plastic container, separator, waterways and cooling tank. After this, the holder is processed again (but this time with a napkin) and put back in its place. A special detergent “Kremklin” must also be used to clean the cooler body. Do not forget to process the back wall of the device and the grille. Now open the hot and cold taps and wait until the detergent flows out of each in turn. If possible, clean the faucets as well. It is recommended to do this with the Antiklin spray. Clean the faucet drains and front panel with a brush.

The final stage

After this, install the taps in place, place the cleaned bottle and fill the device with clean water.

Everything, at this stage, the cleaning of the water cooler has been successfully completed. Do not forget to connect the device back to the 220V network. Now for the next 3 months you can enjoy pure drinking water from your water dispenser.

How much does a professional water cooler cleaning cost?

The price of such services in Russia is about 900-1200 rubles, so if you want to save an extra thousand, feel free to use these instructions!

Reading time: 4 minutes. Published 12/02/2018

Today, the cooler is widely used both in everyday life and in offices. But in order to receive only clean water, systematic care of the cooler is necessary.

According to sanitary standards the cooler needs to be treated at least once every 6 months, even if it is rarely used. The rear grille of the device (condenser) must be cleaned of dust at least once a year. An office water cooler requires maintenance and flushing twice as often.

Why do you need to clean?

Many housewives wonder how they can clean a water cooler at home, for example, family.

The purpose of cleaning is to remove microbial flora. To the cooler in various ways a lot of bacteria get in. They can cause diseases dangerous to people.

The hygiene label, which protects the valve from contamination, is not always removed when installing the cooler. This leads to the penetration of non-sterile particles of paper and film into the water purification apparatus.

During operation, a biodeposit forms inside the container in the form of a film covering the parts. When this film comes into contact with water, the liquid becomes contaminated.

To slow down the formation of bioplaque, you need to use water. High Quality.

Signs of the presence of bacteria in the water are bad smell and taste.

What to do?

Now let's talk directly about the cleaning itself. Here is a small guide on how to clean a water cooler at home.

First, wash your hands thoroughly. Then disconnect the cooler from the power supply and wait about 15 minutes for the hot water in the tank to cool.

The bottle is removed on a special waterproof mat and the old water is drained. This must be done carefully so as not to get burned as a result of exposure. hot water. In this case, the procedure must be strictly observed.

The liquid is drained first from a hot and then a cold tap. If you drain water from two drains at the same time, effective disinfection will not work. Only after draining the liquid from the tap, you can open the drain plug.

Further cleaning is carried out using a special disinfectant"BIOR 1". For rinsing, 5 liters are enough, based on approximately 25 ml of this substance per 1 liter of water. This solution is used for internal treatment of the apparatus using brushes and hedgehogs. The substance must be left inside the container for an hour to disinfect.

Containers with disinfectant should not be treated with hot water to avoid destruction of the tank and heating element.

To protect the skin of your hands, you should use rubber gloves. If the substance accidentally comes into contact with the skin, rinse the affected area with running water.

The parts located in the drip tray, as well as the body of the device (including the grille and back wall grates) are washed with a special detergent"Kremklin".

Then you need to remove the bottle holder along with the needle and disinfect them. The bottle receptacle in which the container is installed is washed with plain water or detergent 3 times a week, as dust gets in there.

Should be wiped thoroughly internal surfaces device with a dry, lint-free soft cloth.

The separator, drains, and cooling tank require careful treatment with a disinfectant solution. This can be achieved by pouring the product inside and allowing some cold and hot water to flow out of each tap.

The surface of the taps can be cleaned with a brush using Anti-Clean spray.

Then the device must be plugged in and left to work for 30 minutes. After turning off the tool and cooling the water, the drain plug is unscrewed, the water is drained, and the tank is dried.

Reinstalling the drain plug and filling the tank with solution citric acid, repeat the procedure, unscrewing the drain plug and drying the tank. This must be done 3-4 times until there are no traces of scale left. Remains of the acid solution are easily washed off with a stream of running water.

It should be remembered during sanitization The device should not be left unattended. If you still have doubts about how to clean a water cooler at home, we recommend watching specialized videos and photo reports from specialists.

Examination

How can you check the quality of the sanitization performed?

The taste of water after cleaning the device may indicate that the cooler has not been thoroughly processed.

Sanitation will be more effective if it is done while replacing an empty bottle with a full container.

In offices, apartments and houses for bottling, heating and carbonation drinking water a cooler is often used. The safety and effectiveness of this device depends not only on the water poured into it, but also on the cleanliness of the cooler itself. The main source of infection is the users themselves and the people responsible for refilling the device. However, even with correct operation Disinfection of coolers is necessary from time to time.

Cleaning and disinfection of cooler internal tanks

If the quality of the water in the cooler has deteriorated, this is likely the result of microorganisms that have settled in the tank. Bacteria most often enter the water during bottle changes. It is enough to complete this procedure at least once with dirty hands how invisible microbes immediately get inside. The cooler is designed for them good conditions for reproduction, which they actively use.

People servicing the cooler do not always treat the cap of the replacement bottle with due diligence. It must be disinfected before installing the container. This point is sometimes overlooked. If the bottle cap is covered with a sticker or shrink cap, these accessories must be removed. Otherwise, paint or other substances will get into the water and then into the human body.

During operation of the device, mucus may form at the bottom of the container. The presence of bacteria in the cooler is also indicated by thin film on rubber and rubber gaskets. At the same time, the taste and smell of water becomes unpleasant. High-quality disinfection of the water cooler will help get rid of this dangerous situation in many respects.

Ways to disinfect coolers

Sanitation of coolers can be carried out either by the users themselves or by invited specialists. Mandatory cleaning and sanitary maintenance of the device consists of several stages:

disinfection from microbes (includes washing the body and removable parts);
descaling heating elements and other details;
flushing the cooler using several cycles.

For disinfection, substances such as chlorine, iodine, ammonia and acetic acid. There are special disinfectants that act more efficiently and quickly. Subject to processing:

storage tank;
streams at the bottom of the reservoir;
delimiter;
water intake socket;
hidden cooler cavities;

Professional cooler disinfection

The most profitable way to obtain high-quality drinking water and ensure the longevity of the device is timely disinfection of coolers. Moscow offers several options for this service. Good results are obtained by processing in specially equipped rooms. After all, sterile conditions are necessary for high-quality disinfection.

Our employees have extensive experience in the field of disinfection. They compare favorably with others in that:

know how to choose the right disinfectants,
know what concentration active ingredients necessary in each individual case;
use certified drugs and the latest equipment;
undergo medical examinations in a timely manner;
have medical records.

We provide a range of services for businesses and individuals. This includes professional disinfection water cooler. Our service price is affordable. Call us and we will help you quickly and efficiently solve your cooler maintenance problem.

Almost everyone has encountered the problem of water blooming in a cooler. It is dangerous to drink such water. This process must be fought, and it is better to initially prevent the appearance of greenery.

Note! If the water in a cooler bottle has bloomed, this means the presence of microorganisms, algae spores, and bacteria in it.

Prevention methods:

Cause	Consequence	How to fix
Poorly purified water	Foreign tastes, deposits remain on drinking vessels, water may bloom even if not exposed to direct sunlight. Active proliferation of algae and microorganisms that adversely affect the human body	Buy only well-purified water. If you notice greening, change supplier
Improper water storage		Place the cooler out of reach sun rays place
Sanitary violations		Sanitizing the filter at home should be done three times a year. If the cooler is in a crowded place, it needs to be cleaned at least four times a year. When changing bottles, use clean solution containers. Always wash your hands. And you should wash the bottle receiver, needle and bottle neck well

How to clean a cooler at home?

The condition of the water you drink directly depends on the cooler. To ensure that the water remains suitable for consumption, it is necessary to regularly sanitize it.

For cleaning you can use professionals or clean the water cooler yourself. Let's consider the second option.

What you will need:

Citric acid or purchased funds cleaning.
Pure water.
Ershik.
Sponge.
Clean solution container.
A reservoir for the liquid that you will drain.
Six hours time.

Important! Do not use chemicals, abrasives or toxic substances for washing!

To clean at home, you need to prepare so that the process takes as little time as possible.

You need to find out what the volume of the cooler is. Prepare a sufficient amount of purified water. Clean all the tools necessary for cleaning (steam can be used).

Important! You should wash your hands well with antibacterial soap and disinfect the containers you will use.

Invaded microorganisms can cause algae in the water.

The benefits of home cleaning are clear. Estimating how much it costs ready-made product and self-prepared food becomes clear - savings. And quality. After all, we will never try better than for ourselves.

Do-it-yourself cleaning with citric acid

Cleansing with citric acid is the easiest and most inexpensive way. It is harmless and removes dirt well.

What to do. Sequencing:

Switch off cooler from the socket.
Wipe from dust and dirt.
Disassemble the cooler. Remove all detachable parts and wash them. When disassembling, remember how the parts are attached.
Well wash the drop collection, usually this is the most polluted place.
Drain the water.
Remaining from the system must be drained through the drain plug.
Make at home or buy a solution. For homemade solution you will need to dissolve 100 grams of citric acid in five liters of clean water.
Remove bottle receptacles and pour the solution into the cooler.
Give the liquid time fill all containers. If necessary, add solution.
Connect the device to the network.
Wait until the water is completely heated and unplug the cooler from the outlet.
The solution should work. This will take about five hours. Then drain the water completely again.
Flushing. To do this, fill the containers with clean water and drain through the taps. Repeat if necessary.
Before installing a new bottle, You need to check whether you have closed the drain plug.

Why is it noisy after cleaning?

All devices make noise. But if the cooler makes too much noise after cleaning, then it’s worth checking whether you assembled the “machine” correctly.

Note! When assembling the cooler, there should be no extra parts or bolts left.

Check some places that may be making noise:

If you haven't identified If there are no serious problems and the noise has not stopped, contact a service center.

Descaling products

You can use a solution of citric acid and vinegar to remove scale. This is a universal remedy; its range of uses is very wide.

Descaling step by step:

Pour the solution into the tanks.
Plug in the cooler.
Once fully heated, leave it on for 30 minutes.
Periodically drain a glass of solution and add a new one. Repeat the procedure twice.
Drain off all the water.
Use a brush to clean accessible areas.
Fill the tanks with flushing fluid. Repeat the procedure several times.

Timely descaling will help you avoid a number of problems. The taste of drinks changes, the dispenser fails prematurely, the heating time of the liquid increases, and corrosion appears.

Important! Why you need to remove scale - if scale is not removed, it can reduce the life of the cooler by half.

The heating element suffers the most from scale. Its replacement is not expensive. But its failure can damage the system. After replacing everything should work fine.