home · Tool · The windows are flush. Tiled apron flush with the wall. How to install doors flush with the wall

The windows are flush. Tiled apron flush with the wall. How to install doors flush with the wall

Covering a house with siding yourself is quite simple. For such work you will not need to master any special skills. It is necessary to prepare thoroughly in advance. The quality of the result depends on how well all the subtleties of the process are thought out. The work includes not only the installation of panels, but also cladding ground floor and windows. That is why a beginner, when faced with the need to perform such work, often finds himself in a dead end. To understand the cladding process, you will need to familiarize yourself with step by step instructions How to decorate a window with siding with your own hands.

Methods for finishing openings

When creating an attractive window treatment, the type of window is of utmost importance. installed window. It depends on what technology will be chosen for installing siding panels. There are several types of installation of double-glazed windows:


In each of these cases, finishing is carried out even before fixing wall panels, which will be located around the window. In this case, the edges of these elements simply need to be inserted into the groove on the edge of the profile. When performing finishing after installing the panels, the work will cause certain difficulties.

The installation technology is common to all siding panels. The screws should be tightened in the center of the mounting holes. In this case, a gap of 1 mm should be left for cases where thermal expansion will occur. This way the panels will move freely without deforming. If you follow this rule, installing siding panels on the window will be much easier.

Features of window siding finishing can be found in the video:

Attention! According to the instructions, during installation you can fix the elements in arbitrary places.

The sheathing bars must be fastened around the perimeter of the window. Small planks are installed on the slope. This will make it easier to install the finishing profile. The bars must be the same size. This will make the wall surface more even. All work is carried out with a level.

Preparatory stage

High-quality window finishing from the outside requires certain preparation. Such work includes:

  • removal of decorative elements;
  • cleaning the surface from old plaster;
  • removal of old wooden parts;
  • dismantling of communications.

In addition, technical devices and fixtures - antennas and air conditioners - are also removed. The surface is cleaned and dried. It is better to carry out such preparation if it is planned to cladding the entire façade of the building.

Frame installation

When deciding to decorate a window opening with siding, it is worth considering that before such work, lathing should be done. It will be needed for the following reasons:

  • so that the material is securely fastened;
  • it will be much easier to perform cladding;
  • to level the surface of the wall.

The following options are suitable for lathing:

  • wooden beam with a cross-section of 4x6 cm.
  • metallic profile.

Advice! When using wooden beams, before starting cladding, it is necessary to treat the elements with an antiseptic. This will help prevent the wood from rotting and being damaged by insects.

The frame parts are attached at a distance of 20 cm from each other. This step is optimal. If it is larger or smaller, the strength or aesthetics of the structure will decrease.

Insulation

Finishing windows during siding installation involves creating an insulating layer that will protect the window frame and the room behind it from the effects of cold. It is better to perform insulation polystyrene foam boards. It is mounted on dowels with wide heads.

Advice! To protect the insulation from moisture, a film should be laid on top.

Because during installation window frame To avoid the appearance of cracks, it is necessary to prepare the sealant in advance. Thanks to the use of this material, it is possible to increase the hydro- and thermal insulation properties of the structure as a whole.

Window finishing technology

For each of similar cases actions may have different orders. Separately, you should familiarize yourself with the decoration of windows without slopes. Siding in this case includes the use of special platbands.


Advice! For greater reliability, the elements are sealed with sealant.

The panels are cut at the top and bottom of the window structure. The slot should be slightly narrower than the width of the window strip. You can learn more about the technology of cladding window structures with siding from the video:

Recessed structures

Window trims are great in cases where the window is not very deeply recessed into the wall. Thanks to the use of planks, the slopes are closed.

Then the window strip is placed in the hole finishing profile. When joining the planks on the vertical elements that connect to the slope, it is necessary to make special cutouts. Horizontal elements are cut and bent.

If the window is recessed quite deeply, the use of window strips is not required. For such structures, small pieces of wall panels are used. During the installation process, a corner is used.

Installation can be carried out using a special ebb. Its edges must be trimmed and folded under the vertical elements. To increase the reliability of fastening the ebb, a sealant is used.

Installation of siding on windows is carried out in the following order:

  • first, a J-profile is attached around the perimeter of the structure;
  • then the installation of pre-prepared elements of the frame panels is carried out;
  • At the final stage, the corner profile is installed.

During installation, you must follow the same rules as for the general installation of siding panels. Each connection should be created with a gap of 5 mm.

Attention! When performing work in autumn or winter, the gaps should be increased to 10-12 mm.

Arched windows

Such designs look great, but finishing them is fraught with some difficulties. Installing siding on arched windows is complicated by the presence of a curved part in the upper part of the structure.

For finishing, a J-profile is usually chosen, which is quite flexible. However, its cost is significantly higher than that of a regular one. For this reason, its standard counterpart is often chosen. To do this, several cuts should be made in a regular profile, which are made on the mounting part. It is then bent to give the required radius of curvature.

Attention! In some cases, cuts are created on the front side of the product. If carried out carefully, this solution will become an effective design technique.

An alternative option is to replace the arched opening with a polygonal opening. The design of such a window is performed using the same technology. However, the profile cutting will be large.

The ease of bending a regular J-profile will depend on the material from which it is made. In the case of metal, it will yield much harder than plastic. To create an arc of the required radius of curvature, you should choose vinyl siding. To make bending easier, it should be warmed up well. However, do not overuse this - the plastic can easily melt.

conclusions

The overall impression of the facade of the house depends on how well the windows are finished. That is why such work should be treated with the utmost caution. The installation technology is determined by the shape of the window, as well as the degree of its recess into the wall. Such work will be simple even for a novice builder.

If you follow the suggested tips, finishing a window with siding will not be difficult, and the result will be pleasing to the eye.

Before facing it is better to take care of proper preparation opening. It should be cleaned thoroughly. For guard interior spaces from the cold it is necessary to create a thermal insulation layer. It is made from polystyrene foam boards.

At correct execution covering windows with siding decorative elements will not deform under the influence of temperature changes and weather conditions. The process of finishing a window with siding can be learned from the video:

All photos from the article

You can cover a house with siding yourself and quite quickly; you definitely don’t need any special skills for this. You just need to think through all the details in advance, because the work consists not only of installing panels on the wall sheathing, but also in designing the base, as well as window openings. It is the finishing of the window with siding that can confuse a beginner.

Window finishing methods

When finishing window openings with siding, the type of window plays a big role.

There may be such window installation options as:

  • flush with the wall. In this case, wide or narrow trims are used to decorate it. In terms of complexity of work, this is the simplest option;

Note! If you need to design an arched window, then it is better to use a narrow casing; its mounting part can simply be cut at a certain pitch and then bent. But if the bend radius is too large, then bending may become difficult.

  • the window is recessed into the wall to a shallow depth(no more than 200 mm). To design it you can use finishing bar or J-profile, and a special near-window siding strip will cover the slope;
  • For deeper recessed windows, the option of using offcuts of wall panels is suitable. Additionally, you will need a J-profile and a corner for decorating the outer corners.

In all the described cases, the finishing is done even before the wall panels are fixed around it. In this case, during installation, their edges will simply be inserted into the groove on the edge window profiles. If you start finishing after covering the walls, then it will be more difficult to do.

As for the technology itself, the general rules. That is, self-tapping screws/nails/staples should be placed in the center of the mounting holes, without fixing the profile rigidly, the gap between the head and the surface of the material should be approximately 1 mm, this will allow the element to move freely when the ambient temperature changes.

Note! The installation instructions allow for fixing elements in any location.

Also, a common point for all cases of window finishing can be considered the installation of lathing. The bars are attached around the perimeter of the window opening, and small strips will also need to be placed on the slope directly next to the frame, so that you can install the finishing profile or J-profile (for windows recessed into the wall).

Window finishing technology

For each case, the procedure is slightly different; it is also worth considering the finishing separately. arched windows.

Window without slopes

Covering the window with siding from the outside is carried out using special platbands or a regular J-profile.

  • First we check the width of the frame(the width of the window frame is measured);
  • Next you need to cut the platbands. They must be solid; the joints cannot be masked. Required length the strips are determined by the formula L = 2*b + l, where b is the width of the casing itself, and l is the length of the window frame;
  • profiles can be joined at a right angle or at an angle of 45ᵒ, there is not much difference, except that the joint at an angle looks better. When joining, it is imperative to ensure the tightness of the junction of horizontal and vertical elements; this is achieved due to the fact that a cutout is made on the side of the vertical strips, and the section on the horizontal ones is cut and bent;

Finishing a window recessed into the wall

Window strips are ideal when it is not very deeply recessed into the wall (up to 200 mm). Special strips completely cover the slopes, and the side parts of the trimmed wall panels are inserted into the grooves on the sides.

The design begins with installing the finishing profile directly next to the frame. If the slopes are concrete or brick, then it is better to install wooden block at the frame and attach the finishing profile to it.

After this, the window strip is inserted into the groove of the finishing profile, and its outer part attached to the sheathing around the perimeter of the opening. When joining the planks, cutouts are made on the vertical parts adjacent to the slope, and on the horizontal parts the material is cut and folded, this is necessary to ensure a tight joint.

At this point, finishing windows with siding with your own hands is considered complete.

If the window is recessed to a greater distance, then it will no longer be possible to use window trims. In this case, the finishing is done using small pieces of wall panels, as well as a corner for decorating the outer corner and a J-profile.

A special flashing can be installed, its edges are trimmed and bent under the vertical strips. For greater reliability of fastening the ebb, you can use sealant (coat the joint between the ebb and the window frame).

Do-it-yourself window siding is installed as follows:

  • first, a J-profile is attached around the perimeter (the joint with the frame can also be coated with sealant);
  • Next, pre-prepared cut pieces of wall panels are installed;
  • The final stage is the installation of the corner profile.

During installation, the same rules apply as when installing siding in the general case. That is, all connections are made with 5-6 mm deformation gaps.

Note! If the work is carried out in the cold season, the size of the gaps increases to 10-12 mm.

Working with arched windows

Arched windows look great, but their finishing is somewhat more complicated than ordinary rectangular window openings. Finishing arched windows with siding is complicated by the fact that its upper part is curved.

For finishing, you can use a special flexible J-profile, but its price is noticeably higher than the cost of a regular one. Therefore, they often make do with its budget substitute - they take a simple profile and make deep cuts on the mounting part (the part in which there are holes for nails/screws), after which you can bend the profile, giving it the desired radius of curvature.

Note! Sometimes cuts are made on the front side of the profile; if this operation is performed carefully, it will look like an unusual design technique.

As an option, you can consider replacing the arched window opening with a polygonal one. In this case, to decorate it, the same technology is used as for finishing in a normal case, just large profile cutting.

If you decide to try to bend a regular J-profile, then great importance has a material, for example, a steel element will be more difficult to bend, so plastic is more suitable in this case. Window finishing vinyl siding will allow you to bend it into an arc without any problems the desired shape and secure it to the sheathing. To make bending easier, you can warm up the vinyl thoroughly, but without fanaticism, the plastic should not melt.

In conclusion

The overall impression of the house largely depends on the quality of window finishing, so you definitely shouldn’t treat this type of work with disdain. The technology largely depends on the shape of the window, as well as how far it is recessed into the wall, but this work is not difficult even for a beginner in the construction business.

And the suggested tips will help you avoid mistakes when finishing. The video in this article shows the window finishing process.

In the comments to the material, you can ask any question about finishing the window with siding.

What is usually meant by the definition of “tile backsplash”? As a rule, this is a cladding made of something that protrudes from the plane of the wall. At the final project, I offered the Customer a not quite standard version of this decorative element.

First, as usual, plastering the walls. But not quite ordinary. A pass was made in place of the apron. After the plaster of the main wall has dried, the beacons are placed in the gap with a minus thickness of the glue and tiles. The gap on the adjacent wall was not plastered, since the layer there is only 15mm. and there is no point in stretching out 5mm plaster.

Then I laser cut the upper and lower horizons of the recess for the apron




On external corner the wall was installed metal corner for tiles. So that the angle does not get knocked/chipped. View from the apron

Next, we wait until the plaster under the apron dries, prime and lay porcelain tiles. The red spots are tape to protect the wall covering from grouting.


Next, grout, and we get a finished apron.

Here you can see the position of the apron relative to the wall, as well as the outer corner.


Unlike classic version This cladding is a little more labor-intensive. But in the end it is more practical, since there is no need to adjust the cabinets to the upper horizon of the apron. And the side view does not create the feeling of a crooked wall in case of cabinets “creeping” onto the apron.
The customer was satisfied with this decision and its execution, which is very pleasing)))

PVC windows are much cheaper than wooden euro-windows. But in the current time of total price increases, even this amount seems unaffordable to many. Do-it-yourself installation allows you to save on replacing windows. How to install plastic window yourself?

When to bet

When choosing the time to install a plastic window, you should pay attention to:

If you order installation from a construction company, it is better to do it in winter. Firstly, prices are lower (the peak of orders occurs in autumn and summer). Secondly, the quality of installation is immediately obvious: it blows or it doesn’t blow.

If you decide to install a window yourself in winter, be careful when choosing polyurethane foam. It must be designed to operate at sub-zero temperatures.

Measurements and model selection

How to measure a standard window without quarters: the width is measured along the inside of the opening between the slopes, the height is measured from the top slope to the window sill.

When calculating dimensions, you need to add the value to the width installation gap on both sides, to the height - twice the size of the gap and the height of the stand profile. Measurements should be taken in two or three places for both width and height, and in both cases choose a smaller number.

Quarter window (these are often found in brick houses). Measurement is made according to outside window. Width is defined as the distance between the quarters plus twice the overlap of the quarter on the window (up to 4 cm), height - the distance from the top quarter to the low tide plus the overlap of the quarter (up to 4 cm). Under the window sill and ebb there is usually cement strainer, due to it you can increase the glazing.

The optimal window installation depth is approximately a third of the width of the opening wall from façade wall. This distance should not be shortened. Moreover, it is not recommended to place the window flush with the facade: it is coldest here, in winter period Condensation on the glass is guaranteed.

Installation technology

Before installing a plastic window yourself (a day before), it is recommended to fill the internal space of the stand profile with polyurethane foam to eliminate the possibility of a cold bridge forming along this line.

Installation diagram of a plastic window

The old window is dismantled on the day of installation. All opening sashes are removed, the frame is sawed through in several places and torn off using a crowbar. Remove the ebb and window sill. It is also advisable to break up the old plaster slopes and redo them after installation.

Before starting installation, it is recommended to remove the sashes from the new window and remove the double-glazed windows so as not to damage them during the installation process and to make the window structure extremely light. To do this, you must first pry up the glazing beads with a thin spatula, remove them, then remove the bag itself.

Attention: it is advisable to mark the removed glazing beads, because... they may vary in size.

How to install a plastic window yourself:

1. Drill holes for mounting anchors on the inside of the frame. At least three points on the sidewall, at least two on each horizontal line. You need to drill with a metal drill, because... metal reinforcement is located under the plastic profile cladding. The hole diameter is 8-10 millimeters (according to the size of the anchor).

2. Place several backing bars on the lower slope of the opening and install the frame on them. Align horizontally and vertically by driving bars between the frame and the walls.

3. Drill holes in the walls of the opening through the holes drilled in the frame.

4. First, attach the frame from below. Check the location again with a level and plumb line.

5. Insert the side and top anchors and tighten the fasteners.

In a similar way, you can install windows yourself and use mounting plates that have holes for fastening. First, the plates are attached to the frame. Next, install and align the frame as described above. Unfold the plate so that part of it rests on the frame, and part on the slope. Attach screws, check once again for correct installation and tighten the screws.

Once the frame is fastened, the gaps are foamed. After the foam has hardened, trim off the excess. Be sure to seal the seams on both sides with waterproofing tape to prevent the foam from being destroyed by moisture and ultraviolet radiation.

Video “Technology for installing plastic windows”:

The window is installed. All that remains is to design the internal slopes, install the platbands and the window sill.

Features of installation in timber

Peculiarity wooden houses– shrinkage. Shrinkage wooden structures give throughout life, and not just in the first year, like concrete ones. As the walls settle, they exert uneven pressure on the plastic window designs and deform them.

To prevent this from happening, install windows (see photo) in wooden houses made using a frame - an additional wooden frame with movable vertical posts. It protects not only the windows from deformation, but also the facade beams themselves from horizontal displacement.

Installing windows in a timber house is done as follows:

1. Two blanks are made from wooden beams according to the height of the opening.

2. A tongue-and-groove fastening is cut out in the workpieces and slopes. Usually the groove is selected in wooden beam, and the ridge is cut out in the wall of the opening.

3. Cover the ridges with a layer of felt. Put on the stands. Their location must be strictly vertical; this should be taken into account when preparing the tongue-and-groove lock.

4. Two horizontal blanks are made along the width of the window. Grooves are selected at their ends to align with the racks.

5. Lay down bottom part frames Combine with racks, measure horizontally. If necessary, place wedges.

6. Install the upper vertical in the same way, leaving a gap between the frame beam and the wall.

7. The gaps are filled with tow or felt (not polyurethane foam!).

8. A window is placed in the resulting frame as described above.

Now when shrinking vertical bars will slide along the slopes, and she wooden frame it will retain its rectangular shape.

Features of installation in aerated concrete

Installing windows in aerated concrete has its own characteristics, which are determined by the specifics cellular concrete. Additional designs not required, installation sequence is standard. There are several nuances:

1. Fastening is carried out with dowels for aerated concrete. Nails and other similar fasteners are excluded.

2. A hammerless drill should be used to make holes. The holes are slightly larger than the immersed part of the dowel. The distance from the edge of the opening is at least twice the depth of the holes.

3. Three-layer sealing of the installation gap: on the outside there is a waterproofing tape placed on an adhesive-sealant, in the middle - polyurethane foam, inner side seam - vapor barrier tape.

Now you know how to install a plastic window yourself. If it seems difficult, hire professionals; if not, feel free to proceed and do it conscientiously.