home · Networks · Connecting a Samsung smart TV to the Internet. Editing the channel list. Connecting Samsung Smart TV to the Internet

Connecting a Samsung smart TV to the Internet. Editing the channel list. Connecting Samsung Smart TV to the Internet

Often, after purchasing their first SmartTV, users wonder how to connect the TV to the Internet via cable. This question especially relevant for inexpensive TVs that are not equipped with a Wi-Fi module.

We connect the TV to the Internet via a cable from the router

If you have a router and want to use it to connect your TV to the Internet, then in addition to the TV itself and the router (of course, the router must be configured and in working order) you will need network cable. The network cable must be long enough for you to install it in a convenient way, and the cable must be crimped on both sides. If these two conditions are met, then you can proceed directly to connecting the TV.

Step No. 1. Connect the network cable to the router.

First, we need to connect the network cable to the router. This is extremely easy to do. We simply plug the cable into any of the free LAN ports. It will be difficult to miss and plug it in the wrong place, since the WAN port (which is used to connect to the Internet provider) should already be occupied.

Step No. 2. Connect the network cable to the TV.

Step No. 3. Check the Internet.

If the TV was turned on when the network cable was connected, a message about connecting to a wired network should have appeared on the screen.

If the TV was turned off, then you can go to SmartTV and open the browser. If the pages load, then the TV’s connection to the Internet via cable was successful.

Below we will look at a few common questions that may arise when connecting a TV.

What to do if the TV is already connected via Wi-Fi

If your TV is already connected to the Internet via Wi-Fi, it may not respond to a cable connection. In this case, you need to click on the “Settings” button on the remote control and go to “Network - Network Connection”.

There you can change wireless network to wired and thus switch to using cable.

How to set static IP addresses on TV

If to connect your TV to the Internet via cable you need to manually configure the connection and set static IP addresses, then this can also be done. To do this, you need to go to the network selection window, as described above, and click on the “Manual” button.

After this, the screen will appear manual settings networks. Here you can specify a static IP address for the TV, as well as a subnet mask, gateway and DNS.

How to find out the MAC address of a TV

The need to find out the MAC address of the TV may arise in different situations. For example, if you want to connect your TV not through a router, but directly to an Internet provider.

So, in order to find out the MAC address of the TV, you need to click on the “Settings” button on the remote control and go to “Network - Network Status”.

After this, a window will open with information about the network status, where the MAC address will be indicated, as well as other information about the connection.

You can also find out the MAC address of the TV by going to “Settings Support - Info.” about the product/service"


It is not for nothing that Smart TV received such a name, since it really has high level independence. In this regard, setting up an Internet connection is not difficult, since for the most part it is automatic.

Connect the TV to Internet Smart TV is important so that the device can reveal its full potential. Having its own operating system and browser, the device can 100% cover the need for surfing sites and using all media content.

In the absence of a connection, the difference between a TV with and without a smart device is minimized and is not significant. Of course, setting up access to the World Wide Web is an indispensable aspect of using the device. Now let's look at how to connect Smart TV to the Internet and connection methods.

LAN connection Smart TV

LAN is a standard wired connection. Its use is as simple as possible, but there are several nuances that are important to know, for example: what to do if you need to connect several types of equipment? Here we need an external modem, a kind of splitter that allows us to increase the number of connections available Ethernet cables. Thanks to such a device, all equipment will receive the necessary access to the network. Disadvantages of this approach:

  • Must have special tool(preferably for convenience) crimper. It is necessary for crimping twisted pair cables; of course, this can be done with a screwdriver, but this is a more labor-intensive process. Such twisted pairs necessary for connecting devices to an external modem;
  • Presence of wires. Indeed, it is an inconvenience when there are a bunch of wires under your feet that always get in the way;
  • Absence general standard support for this type of connection.

But we should not forget about the advantages of this type of connection:

  • Signal stability. This is a definite plus, since over Wi-Fi the signal can inevitably weaken, disappear, or have some glitches, which does not happen when using a cable;
  • Ease. Settings Smart TV TV with such a connection is not very difficult and is done literally in a few steps.
  • There is no need to purchase a router, which will save your budget.

Now let's move on to the step-by-step instructions:

  1. Connect the cable from the provider to the splitter;
  2. The twisted pair, prepared in advance, is routed to the TV (connector on the side or back).

In the case when the device is a single device, then the intermediate stage, in the form of a splitter, can be skipped. The smart TV itself will try to configure the network parameters and, often, it succeeds. The figure describes the circuit more clearly.

Still, sometimes you have to set up the Smart TV yourself first in order to get access to the network.

Wi - Fi connection Smart TV

It is not necessary to touch the Wi-Fi router if it has basic parameters. You can check it using a smartphone, simply by checking the functionality of the distributed network. Setting standards are identical for all device types.

Smart TV connection via Wi-Fi uses the same scheme as any other, so there is no fundamental difference in the manufacturer or type of equipment. For example, let's imagine how to set up a Smart TV on Samsung, because it is the leader in the niche. For this:

  • Press the “Menu” button on the remote control;
  • Now go to the “Network” section;
  • Click on the “Network Settings” option;

  • At this stage, you should make sure that Wi-Fi is distributed and then press the “Start” button;

  • A search for networks will automatically occur, which will be presented in the form of a list. Most likely, your connection will come first. Select it and enter the password.

Manually setting up a Smart TV connection

This section is valuable for users who encounter problems with automated configuration. Usually the parameters were set incorrectly or did not change at all from the factory settings. This is possible due to false network configuration by the provider or failures in the Smart OS. Here you will have to provide assistance manually, but it is important to find out correct parameters. Information is available either from an active connection on the same network, or by checking the information personally with support.

Receiving data from a computer is a priority method, as it is simple. Double-click on the connection and select “Details”.

Now let's look at the option of setting up Samsung Smart TV

  • Select the "Network" tab from the "Menu";
  • Then “Network Settings”;

  • Click next and in the connection selection window, select yours (cable or wireless);

  • If automatic configuration fails again, click on “IP Settings”;

  • Now enter the received information manually by unchecking the “Receive automatically” checkboxes.
  • Go to the main menu of the TV and press “Home”;
  • In the “Network” tab in the work area, select “Network Connection”;

  • Of the two connection types, select the one you need and click “Set up connection”;

  • Next, click “List of networks” and select yours;

Most modern SMART TVs are equipped with at least a LAN port for connecting it to the Internet via a router. At the same time, on TV you can not only surf the Internet, but also watch movies from computers connected to the same network. But not every apartment has a router yet, but I want to watch movies and access the Internet from the TV. What to do? You can connect your TV to your computer via the LAN connector directly. For this we need a network cable.
Comment: A slight difficulty may arise here - a regular “straight” ethernet cable may not be suitable, although modern network cards can somehow “reverse” the cable logically. Then you will need to try a reverse LAN cable (the so-called “Cross-over”).

We plug one end of the network patch cord into the computer’s network card:

The second is to the LAN port of the TV:

We check the indicators to see if the devices are linked. After this, we proceed to connecting the TV to local network. Let's start with the computer's network card.

Settings on the computer:

There are two options for the development of events:

First- it's simple connect the TV via LAN to the computer without Internet access. In this case, you need to register a static IP address on the network computer - let it be 192.168.1.2 with a mask of 255.255.255.0:

On the TV you will also need to register an IP from the same subnet - for example, 192.168.1.3.

Second- This connecting the TV via a computer to the Internet. To do this, your computer or laptop must be connected to the Internet via WiFi or USB modem. Then we will simply use the mechanism built into Windows ICS- Internet Connection Sharing. It allows you to allow access to the global network to local clients. For this purpose in network connections select the one through which you are connected to the Internet and right-click on it. The connection properties window will open in which we are interested in the “Access” tab:

On it you need to check the box “Allow other network users to use this computer’s Internet connection.” Below you need to select “Local Area Network Connection” or “Ethernet” and click OK. In this case, there is no need to register IP addresses - neither on network card, nor on the TV - everything will be assigned automatically.

Settings on TV:

Everything is done very simply on TV. As an example, I'll look at an LG TV. On other brands, despite the external differences in the menu, the meaning of the actions is the same - just act in the same way.

Let's go to Settings and go to the section Net:

Select an item Network configuration. A special configuration wizard will open:

Then it all depends on which of the options you have chosen and configured on your computer. If we just connect the computer to the TV via a LAN port, then click on the “Set up connection” button and enter the IP address 192.168.1.3 with mask 255.255.255.0 .

If you took the second path using the ICS mechanism, then simply click on “Next”. Automatic network connection setup will start:

Click on “Close”. That's all - you have successfully connected the TV to your computer via the LAN connector.

Video tutorial: connecting a Samsung Smart TV to the Internet using Wi Fi

One cannot but agree that modern TV Samsung Smart TV connected to the Internet gives a person access to any resources on the World Wide Web, unlimited horizons of video and audio files, information and many other advantages. To enjoy all these benefits, you need little - just connect your Samsung Smart TV to the Internet correctly. It is worth noting that this process in itself is not complicated, but not all owners of these TVs can cope with it. If you also have difficulties during this connection, you can contact the competent specialists of the Samsung service center, or read the article below and try to connect yourself.

Execute this connection can be done in two ways: via Wi Fi or LAN cable. Which connection method is better to choose and why? If you are not a fan of wires under your feet, then the first method will be the most convenient for you. There is one small nuance - with this connection method, playback freezes occur when watching movies Online. But such interference can occur at any unstable work Internet networks. You should know it.

Connecting and setting up the Internet on Samsung Smart TV via Wi Fi

  • First of all, check the stability and strength of the signal, as well as the correct settings on your router or router. Next, enter the “Menu” of your Samsung Smart TV. Find the “Network” section, then the “Network Status” subsection and select “IP Settings” in the window that appears. In these settings, set the value opposite the IP and DNS parameters to “Obtain automatically”.

  • Then we go back to the “Menu” in the “Network” section and select the “Network Settings” tab. Once you press the Start button, your TV will begin searching for and listing the wireless transmission devices it finds.

  • In the list that opens, select your router or router and enter the security code in the window that opens.

  • After identifying the entered password, a connection will occur and you will be able to access the built-in web browser on your Samsung TV.

  • If the connection does not occur, then it is likely that there was a malfunction in the DHTPC protocol. In such a case, you should disable the DHTPC settings on your router. Go back to the “Menu” of the TV in “Network Settings” and select the “Enter manually” tab instead of “Receive automatically”. In this window, enter the parameters according to the settings on your router. In the “DNS Server” line, you can enter the value of both the gateway address of the router - 192.168.1.1, and the Google server address - 8.8.8.8.

In the next article we will tell you how to connect your Samsung Smart TV to the Internet using a cable.

6 months ago







Smart TV... When literal translation it means "smart". This is true, since such a device provides the user with many additional capabilities.

Technology, of course, has a direct purpose. However, besides this, it can entertain any user with media content. That is, he can, for example, view video files and photos. In some cases, it can work with data exchange applications.

However, in order to use all the intellectual capabilities of technology, you need to go online. That is why it is inevitable to solve the question of how to connect Smart TV to the global network. This question appears immediately as soon as you purchase such a product.

It must be admitted that there is nothing particularly difficult in this procedure. We will tell you how to do this further.

There are varieties of Smart. Despite this, before connecting it to the global network, you need to know the basic characteristics. These are:

Internet speed provided by the Internet provider;
- wireless signal quality;
- the speed at which the router transmits data in the radio channel.

All these characteristics greatly affect the quality of displaying high-resolution images.

IMPORTANT! Please note that in order to watch 3D movies online, you need at least a speed of 20 Mbit/s. For ordinary HD resolution, a speed of 2 Mbit/s is enough. This means that you need to adhere to proportionality: the higher the picture quality, the higher the speed will be necessary for Smart TV to work correctly.

Let's connect to the network directly via cable

This connection of the TV to the global network provides for the initial binding of the device, which has a built-in Smart TV function, to the MAC address.

How to connect the Internet to Smart TV via a network cable? To do this, open the settings menu and find information about the model. Typically, this list refers to all specifications. Among them is the MAC address we need.

Connection using wires can be done in several ways. And then we will talk about them.

Internet connection - TV

Nothing complicated, provided that the network connection technology is “Dynamic IP”. Simply insert the cable into the LAN port of the TV screen and, following automatic prompts, adjust the network.

In the case when the monitor, after ordinary manipulations, is still not provided with access to the Internet, you can talk to high probability that the system uses “Statistical IP”. This means that this is the very case when the network must be configured manually.

And so specific example for persuasiveness. Let's look at how to set DNS and IP on a Samsung TV.

Once the system is connected to the cable in the Network Settings window, it may display the following alert: “The wired network connection could not be established.” Then you need to select “IP Settings” in the same section.

Then you need to change the “Receive automatically” option to the “Enter manually” option. When the window appears, then you need to enter the necessary IP and DNS. To confirm your actions, you must click on the “Ok” button.

Internet connection - Switch - TV

The switch is well suited if, when you watch TV channels, there is no need to work on a computer or laptop. Such a device is nothing more than a switch between web stream consumers. The switch is inexpensive. Therefore, buying it is not at all problematic.

IMPORTANT! In the case when you need to use several devices simultaneously, you may need the following scheme for connecting Smart TV to the Internet. Note that it is especially popular.

Internet connection - Router - TV

We connect everything one by one. First of all, we connect the network cable to the WAN port of the router, and then the TV device is connected to it. For this purpose, pressed twisted pair is used.

In order for the “connection” for Smart TV to be established automatically, you must first set up a DHCP server. It automatically performs IP transfer. It also assigns DNS. If this action is not performed, then all functions will need to be done manually.

Please note that you can prevent incidents in the operation of the DHCP server. To do this, you must first reserve a single IP address for all devices that are connected via cable to the router.

Internet connection via built-in Wi-Fi

It is much easier to connect to the network if the TV has an integrated Wi-Fi adapter. The first thing you need to do is pre-setting“dynamic” DHCP with a single IP for all gadgets that are used.

To connect Smart TV to the Internet, you only need to perform several operations sequentially. Go to the main menu and select “Network”. In the list of options, select “Network settings”. When the window appears, click on the “Start” button. This will find all the routers that are available.

In the proposed list, select the name of your personal router, and then click on the “Next” button. Enter the installed security key. Its size is at least eight characters.

When all actions are completed, the connection verification stage begins. It is being implemented in Smart TV. If each action was performed correctly, the wireless network will be configured automatically.

Please note that if problems arise during setup, you will have to return to the initial stage and begin adjusting all parameters manually.

Connection using an external Wi-Fi receiver

This method is a good alternative for those who like to save space and do not want to clutter it with all sorts of cables.

IMPORTANT! Please note: in order to connect via external Wi-Fi receiver, the TV needs to have a built-in Wi-Fi adapter. A specific Smart TV model will be able to function correctly only when there is a similar branded set-top box.

How to connect the Internet to Smart TV using Wi-Fi (external type)?

First of all, insert the Wi-Fi adapter into the USB connector of the TV. Next, you need to debug the connection wirelessly through the “Network” menu and the “Network Settings” item. Click on the “Start” button in the new window.

From the list, select the router you need. Log in using the specified password. We confirm each action using the “Ok” button. And we are waiting for the wireless network to be finally debugged.

Features of setting up Smart TV of other brands

Let's talk about the specifics of how to connect the Internet to devices of various brands.

It is possible that your TV does not have a built-in wireless adapter. In this case, before setting up Smart TV, connect to the global network using a modem and cable.

In the main menu you will need to select the following sequence: Home - Setting - “Network” - “Network Connection”.

It is possible to set up Smart TV on an LG TV using Wi-Fi. To do this, in the “Network” menu, select “Set up connection”. When the “List of Networks” window appears, you need to find the name of the access point you need, and then enter the security key. And then the wireless connection is configured automatically.

2. Phillips

To connect Phillips Smart TV to the global network, go to the main menu.

IMPORTANT! Please note that to quickly go to the main menu of the TV, you need to press the Home button on the remote control, indicated by a house.

In the “Configuration” menu, go to the “Network Connection” item and select the connection type. At correct execution Each action the Philips system will notify you that the Internet is connected successfully.

On Sony TVs, the Smart TV option is configured via a router using WiFi connection. To do this, go to the main menu and select the “Settings” item. And then in the “Network” menu you need to select the “Settings” sub-item.

IMPORTANT! In the list that shows all possible connection methods, it is better to select the “Simple” option. It also makes a lot of sense to use the Connection Wizard's prompts.

Solving common problems

Due to problems connecting the Smart TV to the Internet, the device cannot establish a connection to the wireless network or the image is not transmitted correctly. Next, we will look at the problems that arise and tell you how they can be solved.

Incorrect adapter settings. We configure it manually or use the WPS option on the router and TV. You can also connect to the device automatically.

Please note that the WPS button allows you to quickly connect devices without entering a security key. To do this, select the “Debugging via WPS” item in the TV menu, and then press the WPS button on the router.

There is no Internet connection. Reboot the router or TV and perform the setup again. If this does not help, then update the device firmware. Select the “Support” item, go to the “Software Update” tab and select the “Online” item. So you can go to the site with the firmware. The system will prompt you to install latest version BY.

When watching a video, the image is unclear and there is noise. Perhaps the reason for this low speed data transfer and weak router processor. To solve the problem, increase the speed of the wireless network from the provider and buy a more powerful router.

Website pages take a long time to load. Perhaps this happens due to weak level signal. This means you should check how the router is located. It makes sense to move it closer to the TV. If this has no effect, then you need to make sure that data is transferred via the wireless network at a higher speed.

The device turns itself on and off. The problem can be resolved by updating the firmware. You also need to fix the socket better or check the device settings.

TV does not connect to the Internet

Very often the problem lies in the operation of the Dynamic Host Configuration Protocol (DHCP). This can happen by various reasons. When all devices work well through the router, but the TV gives an error connecting to the wireless network, then do this.

Disable DHCP in the router settings. In the TV menu, go to “Network”, go to the “Network Status” item and click on the “IP Settings” button. Change the value of the “Receive automatically” field to “Enter manually”. When the window appears, indicate in it the network settings relative to the router parameters.

We register the public address provided by Google: 8.8.4.4. or 8.8.8.8. We make one more attempt to connect the wireless network and the TV using the “Repeat” button. The network connection should be established, provided you did everything correctly.

Please note that the DHCP protocol is convenient. It allows you to configure the Smart TV connection to the Internet automatically. To do this, you only need to connect the LAN cable to the Ethernet port or connect via Wi-Fi. To perform these actions on your device, you must enable the “Receive settings automatically” option.