Budget drainage: from what materials and how to make gutters and funnels with your own hands. How to make a funnel out of paper with your own hands Do-it-yourself water funnel

Funnel Filter with your own hands. A funnel that will allow you to filter juices, fruit drinks, tinctures and much more 10 times faster.

Hello everyone. Lovers of juices, tinctures, liqueurs and other goodies.

Today I will share my idea of a funnel that helps you do filtering 10 times faster.

I really love different juices... fruit drinks, liqueurs and other delights... how would it be without them in a private yard where you have your own garden.

Every time I do filtration, I noticed that this procedure can take a lot of time, so I decided to fix this matter in my own way.

So for the super funnel, I took a regular kitchen funnel.

According to the idea, the second one should be slightly smaller than the first one in order to fit completely.

I trimmed the second funnel a little... and drilled as many holes as possible. It is important that the neck of the smaller one (its narrow part) does not fit tightly to the second... and so that there is a gap between them.

Now I’m assembling this miracle filter and charging it for filtration..

I put down the filter cloth and voila, the process has begun.

You can filter directly into a bottle with a narrow neck. Now the filtration process goes along the entire plane of the funnel - not just through the bottom according to the classics... it flows down it into a larger one and into a container. Everything is very simple - it’s not difficult to assemble. Such a filter funnel speeds up this process in 10 times... well, the fineness of cleaning can be adjusted by the number of filter fabrics.

Dear reader, watch the video itself.. some additional moments are visible there, as well as the process itself. Share your experience.. opinion - it will be nice.

Is it possible to save money on drainage system? In search of cheap options for organizing rainwater drainage, craftsmen are trying to make parts for gutters on their own, using improvised materials: plastic containers, galvanized steel sheets, pipes. Are such savings justified? What is more profitable: buying factory parts or making it yourself? How long will a homemade gutter last? In any case, there are only 2 ways to spend less:

Save on installation costs and assemble and install the drain yourself.
Figure out how to make a funnel and gutter from scrap materials and design your own system.

Copper drainage system

System calculation: home drainage planning

At the planning stage, markings are made - they mark the installation locations of horizontal (gutters) and vertical (gutters) lines. After determining the footage, calculate the number of additional parts that are needed to assemble the system: fasteners, plugs, connectors, funnels and adapters.

Meterage of gutters and number of funnels: how to calculate correctly

The number of horizontal lines depends on the roof structure and the length of the slopes. The simplest system of two gutters and two downpipes is best option For gable roof with a total area of up to 100 sq. m and the length of the slope not exceeding 10 m.

Scheme for calculating the number of drain lines

In this case, there is no need to double tilt from the center. And you can make a gutter for a drain both from ready-made ones and from homemade parts. The length of the horizontal tray is equal to the length of the slope. Diameter - 10 - 12 cm. The slope of the drain is up to 2 - 3 mm per linear meter. Factory parts are produced in standard length - 3 m.

The number of funnels designed to drain water from the tray into the drainpipe is equal to the number of horizontal lines. If the length of the straight section is more than 10 - 12 meters, then 2 funnels and 2 drainpipes are installed along the edges.

Basic parameters for installing gutters

If the total number of funnels in the planned scheme is two, then calculating the length of the drainpipes is easy. Building height from bottom edge roofs to ground level are multiplied by 2.

When planning more complex structures, calculations are performed for straight lines, drains and planning installation in difficult areas (on ledges, in corners) with the selection special products– corner connectors.

Additional parts: mounting hooks and connectors

To make a gutter for a drain, you will additionally need:

2 caps for each horizontal line.

Connectors - every 3 m if finished parts are connected.

Brackets – for 10 m – 20 pcs. The distance between the hooks should be within 50 - 60 cm.

Hooks are selected depending on the type of fastening. If a strong gable board is installed under the roof slope, not covered with clapboard, it is more convenient to install the box on short brackets.

When fixing to the rafter sheathing, choose ready-made adjustable or non-adjustable hooks with an extension. Such fastenings can be made independently from strips of thick steel 3–4 cm wide.

To connect the funnel to the pipe, you will need 2 elbows of 40 o to lead the drain to the pipe installation line. To attach the pipe to the walls, use special holders or clamps. The pipes are connected with couplings.

Which is cheaper: make gutters yourself or buy ready-made ones

After calculating the number of parts and total length horizontal and vertical branches you can choose from: what and how to make the gutter and drain funnels in order to both save money and install a system that will last at least 10 years.

Plastic PVC structures

The easiest way to make a gutter yourself is to assemble a line of ready-made PVC trays and connectors. Plastic systems cheaper than metal-polymer ones. Processing and installation do not require special skills. The material is easy to cut with a hacksaw; the kit includes all the necessary connectors. Not needed for assembly professional tools.

Advantage of PVC gutters - aesthetics. It is possible to choose a system to match roofing covering or the color of the cladding of the under-roof space. The material does not fade in the sun and can withstand significant temperature changes.

Metal-polymer parts

Metallo plastic gutters- These are steel products in a polymer shell. The cost of metal parts is higher than plastic ones. The service life of the drain is from 30 years. The material has high strength - it can withstand loads during snow melting and melting, and does not crack in frost. Used in drainage systems without restrictions on temperature conditions.

Working with metal-polymer parts requires preparation. Cutting of molded products is carried out exclusively with special scissors or a hacksaw for metal. The use of cutting discs is not allowed - the material must not be overheated during processing.

Transport products to protective film. During assembly, care must be taken to avoid damaging the polymer layer.

The only drawback of metal-polymer drainage is the noise of the gutters. If you plan to install a drain on a low house with an attic, preference is given to quiet polymer trays.

Materials for making gutter parts with your own hands

To make a drain funnel and gutter with your own hands, use galvanized steel and plastic pipes For external sewerage.

Factory drain made of steel

Galvanized steel is sold in sheet form. To make parts, you need some metalworking skills. A system assembled from homemade products will not be durable - during cutting, the thin zinc layer is damaged, and the edges at the cutting site are left without an anti-corrosion coating.

To work with steel you will need:

A special bending machine or wooden blanks that will be used as the basis for forming the gutter.

Bending the sheet to wooden base

Scissors or grinder for cutting.

The sheets are cut to the planned dimensions, bent to shape and the edges are folded in the form of a fold for subsequent joining of the part.

The box parts are connected to each other in two ways: by hot soldering or by installing steel connectors, which are secured with screws.

It is not profitable to make gutters from steel sheets yourself. Flaws:

Difficulties with connection due to inaccuracies in the geometry of parts.

Special machine for working with steel

Short service life - it takes a maximum of 2 to 3 years before holes appear in a home-assembled box.
The process is labor-intensive and time-consuming.

Better try to collect simple system from sewer pipes. Select parts intended for installation outside: pipes for external sewerage - orange. You will have to come to terms with the color - white or gray pipes are intended for indoor installation, the material of manufacture does not have frost resistance, ultraviolet resistance and high temperature. Taking into account the fact that in summer the drainage is under direct sun rays at a temperature of 40 degrees, and in winter - at 20 degrees below zero, pipes for interior work They won't last even 1 season.

Details for self-made drain

To work you will need:

Half of the planned footage of gutters in the form of orange sewer pipes with a diameter of 100 mm.

Couplings for pipes - according to the number of connection points on horizontal branches.

Coupling for gutter connection

Pipes for drainage in a quantity equal to the calculated footage of drains.

Adapters with outlet for making your own funnels for drainage.

Tee with 90° bend – for funnel

Elbows: 2 for each funnel.

Elbows with different angles are used for installation when changing direction: in corners, under a funnel

Sealant for plastic – frost-resistant and moisture-resistant, for outdoor use. You can use acrylic or silicone based adhesive.

For convenient work and quick installation you can select pipes of the same diameter for gutters and drains and thus save on waste.

How to make a gutter and secure a funnel with your own hands

To assemble and fasten horizontal sections of the drain you will need simple tools:

A ruler with a level, chalk or pencil, fishing line or thread.

Screwdriver, self-tapping screws.

Installation of brackets: installation of ready-made and homemade mounts

First of all, it is necessary to secure brackets under the roof - hooks that hold the trays.

When using short non-adjustable brackets, mark on the gable board the extreme point where the first fastener will be fixed. The distance from the edge of the roof is up to 15 cm. A line with a slope is formed from this point. The distance to the last fastener in meters is multiplied by 2. The resulting value is the difference in height in millimeters between the first and last bracket.

Distance from hook to edge of joints

Example. If the distance between the hooks is 8 m, then the height difference is: 8 x 2 = 16 mm. This is the minimum acceptable slope value. Maximum – 8 x 3 = 24 mm.

Slope and calculation of the number of brackets

The installation points of the extreme elements are connected. The brackets are attached along the marked line in increments of 50 cm.

If hooks with extension strips are installed, then after fixing the first bracket to the flooring, measure the distance between the top edge of the board and the middle of the hook. From this point, a slope is formed towards the funnel.

Easy way to do correct slope

To make the process easier, you can mark the fold directly on the extension strips. Lay out a row of numbered hooks end to end. A straight line is drawn from the bend point of the first. Measure on the extreme bracket required value slope and place a mark below the first line. Connect to the point on the first element. During installation, the hooks are attached to the line, and the extension is simply bent according to the markings.

Installation of fasteners with extensions

Assembly of plastic and metal-plastic structures

Plastic trays connected to each other using special parts. Calculate the joint points so that the distance from the edge of the connector to the hook is at least 2 cm. If connectors with rubber seals are selected, then the gutter is installed so that there is a gap of 5 - 6 cm between the edges of the two connected trays. This distance is sufficient for free movement parts during thermal expansion.

The second method is glue. Connector processed adhesive composition: Apply 3 strips of sealant. Two - on the edges and one in the center. Press the groove against the connector and remove any remaining adhesive.

Plastic plugs are installed along the edges of the line.

Plugs, funnel and brackets at the edge of the line

The funnel is mounted according to the connector principle. Make sure that the distance from the outer bracket to the edge of the funnel is up to 5 cm. If the factory funnel is equipped with a seal, then additional sealing is not carried out.

The connection is made on brackets or parts connected on the ground are installed if 2 craftsmen are working.

Instructions for the manufacture and assembly of drainage from PVC pipes

When selecting sewer pipes for a homemade drain, pay attention to 2 important points:

Choose products in the mid-price category - preferably made from frost-resistant PVC for laying in the ground.
Do not skimp on connectors - they must be made of the same material as the pipes (orange, for outdoor installation), from the same manufacturer.

How to make a gutter from a regular sewer pipe? Cut the pipe lengthwise exactly in the center: you will get two gutters 3 m long. For gutters, it is better to buy pipes without connecting sockets.

Slope of sewer pipe gutter

For cutting, use a hacksaw, jigsaw, or grinder with a disk (preferably with large teeth).

Tray with roof connector

The couplings are also cut in half - you get 2 gutter connectors. There is a seal inside the coupling; it is cut separately and placed into the part.

Marking for cutting pipes and joining parts

The joints must be sealed using acrylic or silicone construction sealant.

What to make the plug from? When purchasing tees for funnels, choose products with decorative covers. The lid must be cut into 2 halves and glued with sealant to the edges of the tray.

Tee with factory threaded cap

In the same way as the connector, cut top part tee. The product is cut so that the outlet is located under the gutter. Fix the funnel with sealant or screws. The elbow is connected to the lower outlet with the socket facing up.

Artistic homemade funnel from a sewer tee

The pipe is assembled from pipes with connecting sockets. On the top pipe you need to install a bend at 40 - 90 o to connect the drain to the gutter. Measure the length of the segment between the knees. Cut a piece of pipe without sockets and connect the system.

In the lower part, install a branch - an elbow, cut the part so that the drain falls into the center of the rain inlet or into the ground, at a distance of 40 - 50 cm from the edge of the blind area.

Video: how to make a gutter from a sewer pipe

Is it worth saving on drainage? If the roof structure is simple, gable or hipped, you can save on installation work. Savings on material are highly questionable. Considering that even expensive outdoor sewer pipes designed for installation in the ground, not on outdoors, then predict how long it will last homemade system- impossible. In addition to fragility, there is another drawback: very controversial appearance designs. Such gutters are only suitable for temporary outbuildings in the country.

Budget plastic gutters are designed for year-round use in all weather conditions. Special connectors, brackets and adapters will facilitate the installation process. And if you choose glueless connectors, you can assemble the system in a couple of hours.

Sometimes there are cases when you urgently need a funnel to pour sugar, cereal, or pour water into a container with a narrow neck. But it is not at hand. Not everyone has such a useful thing in their household. How to be? That's how. In our material we will tell you how to make a funnel from paper of any density.

The easiest way

No tools are required to quickly make a funnel. Just take a sheet of paper and fold it diagonally towards you so that the edge of the short side of the rectangle (and the sheet of paper is a rectangle, not a square) coincides with the edge of the long side. It turned out right triangle. We press down the diagonal at the bend so that our workpiece does not unfold, and continue the process.

Now you need to fold the resulting workpiece again in the same manner as before, only now we bend the upper side of the triangle towards ourselves, the one that represents the bend made the first time. Compare the edges from below again. The result is a sharp triangle, one of the short sides of which consists of unevenly protruding edges. It’s okay, this will not affect the manipulation of water or bulk materials that we will pour/pour through the future funnel.

But it turned out to be just some kind of incomprehensible cone, and we were interested in how to make a funnel out of paper with our own hands. Good news. This cone is already a potential funnel. All that's left to do is tear it off small corner from the sharp end and, taking the cone in your hand, bend one side of it from single paper.

Squeezing the product a little and looking inside, you will see that this is a funnel with a hole at the narrow end. Yes, it is imperfect, one side is too thick, the other is too thin, but that’s okay. It is enough for one-time use. Although some may find it too narrow. For such there is the next section.

Wider funnel

Just fold the sheet in half. Then we fold the resulting quadrangle again. We tear off the tip of the corner at a blind bend and straighten the cone so that one side of it is three sheets, and the other is one. Done, you have made a funnel with a wider neck out of paper with your own hands. One time use is enough.

Method using tape

Do you like seeds? Previously, grannies constantly sold seeds in glasses, and they had containers prepared for them - paper bags. These are potential funnels. And even in those days, when cellophane had not yet come into widespread use, in stores, sellers made paper bags in which they packed everything, from sugar and cereals to sweets and cookies. How to make a funnel of this type from paper?

Place a sheet of paper in front of you with the long side facing you. We position it so that its edge coincides with the edge of the tabletop. TO right side We glue a piece of tape on the long side of the sheet facing us so that half of the piece sticks out over the edge. We take hold of the protruding edge of the tape with our thumb and forefinger and begin to wrap the sheet around our hand. When we have a cone, we glue a piece of tape to its inside, which is held between our fingers. To do this most effectively, we press this part of the cone to the table.

All. All that remains is to glue it to outside the bag is the other end of the paper that tends to unfold. The cone is ready. We tear off its sharp tip - and the funnel is ready. It may be disposable, but you don’t need to hold it so that it doesn’t turn around.

Conclusion

I would like to hope that our unique “master class” on how to make a funnel out of paper will be useful to you. Of course, these are not all options, but only the simplest and fastest. Some went even further and invented a way to make a funnel with handles out of paper. You can learn about it from the following video:

By using cardboard instead of paper and resorting to glue, tape and scissors, you can make even more advanced and even reusable funnels. But more about this some other time.