Premium class, BO brand (baseless), which is produced Russian company"TechnoNIKOL". TECHNOELAST Barrier BO is a self-adhesive waterproofing material, which is produced by applying a self-adhesive bitumen-polymer binder mixture onto a special film, and having a protective layer. Self-adhesive bitumen-polymer mixture consists of bitumen, SIS (styrene-isoprene-styrene) polymer modifier and special adhesive additives, a siliconized anti-adhesive film, a protective layer of polymer film.

The baseless waterproofing fabric TECHNOELAST Barrier BO is a durable and waterproof material (10-year waterproofing guarantee), is resistant to temperature fluctuations, has high flexibility, ductility and elasticity, which allows the use of this material in waterproofing of any shape and configuration. Rolled self-adhesive baseless waterproofing material TECHNOELAST Barrier BO belongs to the “Premium” class in the TECHNONICOL waterproofing line and has a service life of 30 to 40 years. Bitumen-polymer self-adhesive waterproofing material of the TECHNOELAST Barrier BO brand is produced in rolls, 20 m long, 1 m wide, and 1.5 mm thick, delivered on pallets.

Application of TECHNOELAST Barrier BO TECHNONICOL

Baseless self-adhesive waterproofing material TECHNOELAST Barrier BO is used for the device internal waterproofing residential and industrial buildings and structures, waterproofing shallow foundations up to 3 m, waterproofing interior spaces under the screed, as well as for vapor barrier of various building structures. Waterproofing materials of the TECHNOELAST Barrier BO brand can be used in all climatic conditions, including the harsh conditions of the polar winter (SNiP 23-01-99*). Self-adhesive baseless waterproofing material TECHNOELAST Barrier BO can be used for waterproofing objects where the use of fire is prohibited, and it can also be laid on flammable substrates.

Installation and laying of self-adhesive fabric TECHNOELAST Barrier BO occurs without special additional equipment, does not require additional fasteners for attachment to the base, and can be produced even in confined and limited spaces. Installation and gluing of TECHNOELAST BO Barrier is very easy and simple: from the bottom side of the canvas, remove the siliconized protective film, then the canvas is glued to the base. When carrying out work, the temperature of the base and the canvas itself must be at least +5°C; if the temperature is lower, then it is necessary to warm up the lower surface of the material and the base on which it will be glued. Self-adhesive waterproofing material TECHNOELAST Barrier BO is recommended to be stored protected from direct sun rays place, store in vertical position and at temperatures from -15 0C to +30 0C.

Technical characteristics of TECHNOELAST Barrier BO

I approve

CEO

JSC "TechnoNIKOL"

___________/Kolesnikov S.A./

Management

on the design and installation of waterproofing from self-adhesive
bitumen-polymer material"Technoelast-Barrier"

Moscow 2007

“Guidelines for the design and installation of waterproofing made of self-adhesive bitumen-polymer material Technoelast BARRIER, produced by the TechnoNIKOL company” was developed by Roof Management LLC (D. A. Fisyurenko, head of the “ Special materials» TechnoNIKOL company, Gorelov Yu.A. Sales Director of the TechnoNIKOL company, S.N. Koldashev Head of the technical support service of the TechnoNIKOL company, Lychits A.N. TechnoNIKOL technical support specialist). The manual takes into account the comments and additions of Voronin A.M. (Candidate of Technical Sciences, Head of the Roofing Department of TsNIIPROMZDANIY).

1. PREFACE.

1.1. This manual has been developed in addition to chapter SNiP 2.03.11-85 “Protection of building structures from corrosion”, SNiP 3.04.03-85 “Protection of building structures and structures from corrosion”, SNiP 3.04.01-87 “Insulating and protective coatings”, SNiP 3.04.01-87 “Insulating and Decoration Materials» to series 1.010-1 “Waterproofing underground parts buildings and structures. Issue O-2. Pasted waterproofing. Materials for design." Contains the requirements for materials, the base for waterproofing, parts and units of waterproofing, as well as technological methods for laying the material on the prepared surface.

1.2. The manual is intended for practical application organizations carrying out waterproofing installations reinforced concrete structures, as well as organizations carrying out acceptance and quality control of the production of these works.

2. GENERAL PROVISIONS.

2.1. The manual applies to the installation of waterproofing of reinforced concrete structures using rolled waterproofing self-adhesive bitumen-polymer material Technoelast BARRIER produced by JSC TechnoNIKOL according to TU 5774-004-72746455-2007.

Technoelast BARRIER is used:

· when waterproofing interior floors of buildings and structures, when working in cramped conditions;

· when installing waterproofing of underground parts of buildings and structures.

Waterproofing material Technoelast BARRIER can be used:

· as a vapor barrier material when installing floors or when laying floor coverings;

· when installing vapor barriers in roofing structures on a base made of galvanized profiled sheets (corrugated sheets) and prefabricated reinforced concrete slabs;

· to protect surfaces and welded joints steel pipes and other metal surfaces from corrosion.

2.2. Waterproofing self-adhesive bitumen-polymer material Technoelast BARRIER can be used in all construction areas of the Russian Federation, including minimum temperature the coldest day according to SNiP 01/23/99 is below minus 40°C.

2.3. This manual contains mandatory requirements that must be observed when designing and installing waterproofing during the construction and repair of structures, monitoring the work and accepting structures into operation.

3. Material properties.

3.1. The Technoelast BARRIER material consists of a non-rotting base - polyester, coated on both sides with a bitumen-polymer adhesive composition. The self-adhesive compound is made from a mixture of high-quality bitumen and specially selected polymers. The surface of the material is covered with a special polymer film that protects from mechanical stress. The film not only increases chemical resistance material, but also increases its vapor barrier properties. The adhesive layer is covered with a special anti-adhesive siliconized film.

The main physical and mechanical properties of the material are given in Table 1.

Table 1.

Properties of the material Technoelast BARRIER

3.2. The list of materials used for waterproofing using the self-adhesive material Technoelast BARRIER is given in Table 2.

3.3. Materials that can be used for waterproofing Technoelast Barrier are given in Table 3.

Table 2.

List of materials for waterproofing:

Table 3.

Component materials for waterproofing:

3.4. Storage conditions.

The material must be stored in original packaging at temperatures from -15 to +30ºC in closed warehouses. The material is stored on pallets, in a vertical position, in one row in height. It is necessary to ensure a distance from heating devices not less than 1 m.

4. Constructive solutions.

· Waterproofing under cement-sand screed.

Rice. 1

· Waterproofing on a prefabricated screed.

The prefabricated screed can be made of asbestos-cement sheets, cement particle boards(CBPB), tongue and groove boards, moisture-resistant plywood, oriented particle board(OSB), gypsum board and gypsum board sheets.

Rice. 2

* - to reduce construction noise, it is recommended to use the sound-waterproofing material Technoelast Acoustic Super.

· Waterproofing of concrete structures.

Rice. 3

5. Requirements for bases for laying self-adhesive material Technoelast BARRIER

5.1. The following can serve as the basis for a waterproofing carpet:

· reinforced concrete load-bearing slabs, the seams between which are sealed with cement-sand mortar of a grade not lower than M150;

· leveling screeds made of cement-sand mortar with a compressive strength of at least 15 MPa (M150), as well as prefabricated dry screeds made of flat asbestos-cement sheets, cement-bonded particle boards with a thickness of more than 10 mm, gypsum board (gypsum plasterboard sheet) and gypsum fiber board (gypsum fiber sheet);

· any metal bases, incl. pipes

· wooden bases (tongue and groove boards, moisture-resistant plywood, oriented strand board (OSB), etc.).

5.2. The surface to be waterproofed must have a slope of at least 2%.

5.3. Laying on a wet or damp substrate is not permitted.

5.4. The surface to be waterproofed should not have cavities, concrete sagging, cracks, irregularities with sharp edges, oil stains, or dust. Oil stains are removed by burning, concrete sagging is cut down or sanded. Small irregularities should be filled with TECHNONICOL hot roofing mastic No. 41.

5.5. The surface of the base must be flat and smooth. When checking the evenness, the gaps under the three-meter rail should only be of a smooth outline and no more than one per 1 m. Maximum depth the lumen should not exceed 5 mm.

5.6. If there are individual irregularities 10-15 mm deep on the surface to be waterproofed, they are eliminated by filling with putty mixtures, which must be easy to lay and cracks should not form in them after drying.

5.7. The temperature of the base on which the self-adhesive material is laid must be above the dew point temperature.

5.8. Back to start waterproofing works compressive strength concrete base must be at least 0.75 stamp.

5.9. Before installing waterproofing, the surface to be insulated must be cleaned of construction waste, dust, cement laitance films. The laitance film is removed by dry or wet blast-abrasive cleaning. The final removal of dust is carried out with an industrial vacuum cleaner. Surface treatment with cutters that form grooves in concrete is not allowed.

5.10. Before installing waterproofing, the insulated surface must be dry. Concrete moisture or cement-sand screed in the surface layer at a depth of 20 mm should be no more than 4%.

5.11. When installing waterproofing, it is necessary to use a primer. A primer is used as a primer bitumen TECHNONICOL No. 01 or bitumen emulsion primer TECHNONICOL No. 04.

6. Laying the material.

6.1. Preparing the surface for laying the material.

6.2. Laying the material.

The pasted panels should not have folds, wrinkles, or waviness, but if this happens, the area with the folds is torn off from the surface. Apply to the surface thin layer TECHNONICOL mastic No. 23 (Fixer) and lay the smoothed material.

Self-adhesive waterproofing materials are laid at an air temperature of at least +5ºС. At air temperatures below +15ºС during installation, the adhesive surface and material are heated with industrial hair dryers.

Before laying, the materials must be kept at a temperature of at least +20ºС for 24 hours.

When performing waterproofing work, precautions should be taken to prevent oil, gasoline, diesel fuel and other solvents. In case of spillage of these materials, the damaged area is cut out and a patch is applied.

6.3. Conjugation of vertical and horizontal waterproofing.

7. Laying self-adhesive material on metal surfaces.

7.1. The material can be used for waterproofing pipes with an operating surface temperature not exceeding +45ºC.

7.2. During operation, the material must be protected from exposure to sunlight.

7.3. When using the Technoelast BARRIER material to protect welded joints of pipes and their surfaces from corrosion, the material is cut along the panel into strips depending on the diameter of the pipe.

7.4. Metal surfaces must be primed with mastic roofing TECHNONICOL No. 21 (Technomast). After the mastic has completely dried (there should be no traces left on the fingers when touched by hand), the material is glued on. The material is wrapped around the pipe with an overlap of at least 20-30 mm over the adjacent turn.

8. Options for cutting material when gluing external and internal corners of a waterproofed structure.

8.1. Option for cutting and laying material in the outer corner.

Bring the ends of the waterproofing material close to the wall. If necessary, cut the roll of material closest to the wall along the canvas.

Laying the material at the junction must begin from the corner. To do this, prepare two strips of material of the required length. The length is determined by the height of the insertion of the material onto the vertical wall and the amount of insertion onto the horizontal plane.

The material is placed on a horizontal surface at 150 mm.

Make cuts in the fabric according to the diagram below.

· Gluing the petal to the vertical wall.

Place the bitumen bead at the end junction of the material sheets to the wall.

Roll over areas where the material overlaps with a roller.

After external corner formed, a patch is placed on it using a hot air hair dryer.

8.2. Option for cutting and laying material in the inner corner of the structure.

Bring the ends of the waterproofing material close to the wall. If necessary, cut the roll of material closest to the wall along the canvas.

Laying the material at the junction must begin from the corner. To do this, prepare two strips of material of the required length. The length is determined by the height of the installation of the material on the vertical wall and the size of the installation on horizontal plane.

The material is placed on a horizontal surface at 150 mm.

Cut material blanks according to the diagram below.

Cut the anti-adhesive film along the fold lines.

Lay the workpiece by removing the anti-adhesive film from each section sequentially, in the following order:

· Laying on a vertical wall;

· Laying a roller of TECHNONICOL mastic No. 23 (Fixer) on the transition from horizontal to vertical surface;

· Laying on a horizontal plane (150 mm),

· Gluing the petal to the vertical wall.

The overlapping areas of the material are rolled with a roller.

The second blank is glued in the same order.

After internal corner formed, a patch made of Technoelast BARRIER material is placed on it using a hot air hair dryer.

9. QUALITY CONTROL OF WATERPROOFING.

ACCEPTANCE RULES.

9.1 Installation of waterproofing must be preceded by acceptance of the base or leveling layer. The contractor must provide the customer with a work log, test reports for the leveling layer material to determine strength, water resistance, frost resistance, humidity, as well as certificates for hidden work based on the results of instrumental monitoring of surface evenness and slopes. Upon acceptance of the leveling layer, its compliance with the requirements of Section 5 of this Manual is determined.

9.2. The evenness of the base is checked with a three-meter lath in accordance with GOST 2789-75*. The rail is laid on the surface of the base in the longitudinal and transverse directions and, using the included meter, the gaps are measured along the length, rounding the measurement results to 1 mm. Clearances under a three-meter rail should only be smooth in outline and no more than one per 1 m. The maximum depth of the gap is not must exceed 5 mm.

9.3. The moisture content of the base is assessed immediately before installing waterproofing using a non-destructive method using a surface moisture meter, for example, VSKM-12, or on concrete samples drilled from the leveling layer or roadway slab, in accordance with GOST 5802-86. Humidity is determined at three points on the insulated surface. For a base area of ​​more than 500 m2, the number of measurement points is increased by one for every 500 m2, but not more than six points.

9.4. Before performing waterproofing, acceptance is carried out waterproofing materials according to passports in accordance with GOST 2678-94 and GOST 26627-85, comparing the physical and mechanical characteristics with those given in this Manual. At the customer's request for a control check physical and mechanical characteristics material tests are performed in accordance with Technical specifications for its production and GOST 2678-94. Determination of quantitative indicators of characteristics must also be carried out in the case of overdue warranty period storage of material. If the received materials do not comply with regulatory requirements, a defect report is drawn up and such materials are not used in the production of work.

9.5. When accepting the waterproofing, a visual inspection of its continuity is carried out over the entire waterproofing surface, and the presence of defects in the adhesion of the waterproofing is determined. The quality of waterproofing adhesion is determined visually by the presence or absence of bubbles and by tapping the waterproofing with a metal rod. Unglued areas are identified by a dull sound.

9.6. If there are bubbles in the waterproofing, indicating that it is not bonded to the base, they are eliminated. The bubble is cut crosswise. The unadhered ends of the material are folded back, TECHNONICOL No. 23 mastic (Fixer) is applied to the base and the bent edges are glued by rolling the area of ​​the bubble with a roller. In place of the bubble, a patch is installed, covering the damaged area in all directions with 100 mm incisions. When installing the patch, the top surface is heated with a hot air dryer. No more than three patches per 100 m2 are allowed.

9.7. The adhesion of rolled materials is checked by a peel test, for which a U-shaped cut with side dimensions of 200x50x200 mm is made in the waterproofing material. The free end of the strip is torn and pulled at an angle of 120-180°. The rupture must be cohesive, i.e. delamination should occur along the thickness of the material. Based on the test results, a protocol is drawn up. The test must be carried out 1 day after gluing the waterproofing at a temperature not exceeding 30°C under the waterproofing.

9.8. The results of acceptance of waterproofing are documented in an act for hidden work in the established form.

10. SAFETY WHEN PERFORMING WATERPROOFING WORK.

10.1. Waterproofing work is carried out in compliance with the safety rules provided for by chapter SNiP 12-03-01 “Safety in construction”.

10.2. Waterproofing work must be carried out by waterproofers who have passed the technical minimum in production technology and safety in accordance with the established procedure. Work management and quality control should be carried out by persons with experience in waterproofing work. Each worker, when allowed to work, must undergo training at the workplace with a corresponding entry in the log.

10.3. The site must have guidance materials for the work.

10.4. Waterproofing work must be carried out in compliance with fire safety requirements. Workplaces must be equipped with fire extinguishing equipment.

10.5. Application primer compositions onto the base should be done in the direction opposite to the direction of air movement (against the wind). In calm weather, it is necessary to use respirators with a carbon filter.

10.6. When working with primers and mastics containing solvents, the use of open flames at the work site is prohibited. The supply of solvent-containing materials at workplaces should not exceed shift requirements.

10.7. Shelters for waterproofing work must be equipped with effective ventilation. If ventilation is insufficient, respirators with a carbon filter must be used.

10.8. The skin of the face and hands should be protected with special protective pastes and creams.

10.9. The production of blasting and abrasive cleaning should be carried out in sandblaster’s protective helmets and special overalls for sandblasting work.

10.10. The noise level of sandblasters can reach 88-96 decibels, which requires hearing protection with headphones.

10.11. There must be facilities at the workplace personal protection: safety glasses, headphones, respirators, gloves, protective clothing and shoes. Shoes must have anti-slip soles. It is not allowed to work in shoes with horseshoes or nails in the soles that can damage waterproofing coatings.

11. ENVIRONMENTAL PROTECTION.

11.1. Before starting waterproofing work, storage areas for materials and flammable gas cylinders must be allocated on the site.

11.2. When working with waterproofing materials, pallets, labels, cuttings of waterproofing materials, buckets of primers and mastics are released. Their disposal must be provided in specially designated areas.

For orders up to 100 kg we offer a budget delivery cost (delivery time up to 2 days):

* Drywall, insulation, lumber, profiles for gypsum boards, foam blocks and bricks are calculated from the table from 100 kg.

**Delivery over 15 km, calculation is based on the “tariff” + 50 rubles per 1 km.

For orders of 100 kg or more:

* provided that the ordered goods fit into a passenger car.

** provided that the volume of the ordered goods fits into a truck of the specified tonnage.

Delivery of unsawn 6 meter lumber (boards, timber) with a volume of up to 2 m3 costs from 3 000 rub.

When paying for delivery by bank transfer, 5% is added to the delivery cost.

Additional requirements for a car, for example, a small height for entering a parking lot or an open body for vertical unloading is paid additionally: + 20% of the cost of the standard tariff.

Delivery terms

Whenever possible, goods are delivered on the day you order or on any other day convenient for you.

Cost of unloading and lifting

Table for calculating the cost of unloading orders:

* Prices in the table are based on a working freight elevator, regardless of the floor.

** In the absence of a freight elevator, the cost of the lift is multiplied by the number of floors to the apartment where the goods need to be unloaded.

*** The minimum order cost for unloading and lifting is 500 rub.

Important!

The service "Lifting Material" includes cleaning the entrance, removing garbage and other ensuing consequences after lifting building material, are not included in the price. Prepare in advance for the service you ordered. Thanks for understanding!

Technoelast Barrier BO is a modern, reliable waterproofing material, for the production of which a special polymer film is used. Ease of installation is ensured by applying a binder and self-adhesive substance. Immediately before installing the material, you simply need to remove the protective film from its lower part.

The increased ductility and flexibility of the waterproofing material will allow it to be quickly and effectively fixed to the surface. It can be used for interior and exterior work in building structures various types. Technoelast Barrier BO will help protect shallow foundations from moisture.

Features of waterproofing

Technoelast Barrier BO does not have a base, which increases its elasticity. Installation of the material does not require heating, which makes the product suitable for installation in confined and confined spaces.

The waterproofing sheet is only 1.5 mm thick, which increases the aesthetic appeal of the surface being formed. Professional installation will make the insulation visually almost invisible. It has high levels of water resistance and water absorption.

Baseless Technoelast Barrier BO is a new generation self-adhesive material. The presence of an adhesive layer on the back surface of waterproofing sheets allows one to avoid fire laying. The coating is in demand for the protection of building structures and structures if it is impossible to use weld-on coatings. Service life more than 25 years.

Material structure

Baseless Technoelast Barrier is made by applying a one-sided bitumen-polymer binder to a polyethylene film. The binder contains polymer modifiers and special adhesive additives. To prevent sticking on bottom side The waterproofing is coated with a removable anti-adhesive siliconized film, and on the top there is a thick polypropylene film with a logo.

Technical characteristics of Technoelast Barrier BO

Areas of application

Waterproofing Technoelast Barrier BO is used for the following purposes:

• protection of shallow foundations (up to 3 m) from the effects of soil moisture;
• protection of floors in premises under screed;
• protection of bathrooms;
• vapor barrier of building structures (in atmospheric conditions, ultraviolet protection is required);
• creation of lining waterproofing layers roofing systems;
• as the bottom layer in a two-layer roofing system.

Installation features

For styling baseless Technoelast Barrier BO 20 sq. m. you only need cutting tool and bitumen primer TechnoNIKOL No. 4 for surface preparation. Mastic is not needed, since the canvases have their own adhesive layer.

Installation of the material is carried out at a temperature not lower than +5 ° C. At negative temperature It is recommended to preheat both the base and the waterproofing on the glued side. Good adhesion baseless self-adhesive material is provided by a specially prepared surface treated with a bitumen primer.

Technoelast Barrier BO sheets with a thickness of 1.5 mm can be laid on leveling layers of the following types:

• gypsum fiber sheet;
• plasterboard sheet;
• moisture-resistant plywood;
• asbestos cement sheet;
• cement bonded particle board;
• oriented strand board;
• reinforced concrete load-bearing slabs;
• metal.

Immediately after the bitumen primer has dried, the Technoelast Barrier BO sheet is rolled out over the surface and tried on. It is important that the material fits tightly to the protruding structural elements. Then the canvas is rolled from both sides to the center and the anti-adhesive film is cut in the middle. One of the workers carefully pulls out the protective layer, simultaneously unwinding the roll, and the second smoothes the waterproofing with a brush. Wrinkles and folds on the surface are not allowed. The size of the side overlaps should be at least 8 cm.

Transportation and storage

Transportation of Technoelast Barrier is carried out by all types of covered transport in accordance with the Rules for the carriage of goods in force for transport of this type. The material Technoelast Barrier BO is produced in the form of rolls measuring 20x1 m, supplied on a pallet (23 rolls), packed in UV-stabilized film. Roll area 20 square meters(1 pallet - 460 sq.m.).

Rolls of Technoelast Barrier BO should be stored in a dry indoors in a vertical position in one row in height and at a considerable distance from heat sources.

Buy Technoelast Barrier BO in Moscow

The Baurex online store sells original TechnoNIKOL waterproofing materials with a quality guarantee. The Certificate of Conformity for Technoelast Barrier BO can be downloaded in the “Documentation” section.

Our advantages:

• the ability to pay for orders for individuals in the amount of up to 100 thousand rubles upon receipt;
• free consultations from technically competent specialists on a range of materials;
• installation supervision services;
• quality control of waterproofing work performed by other organizations.

We organize delivery of Technoelast Barrier BO in full accordance with the manufacturer’s recommendations for storage and transportation of materials.

To place an order, call the phone number listed on the website.