Maintenance instructions for water heater Atlantic 100l. Heating systems for country and country houses. Boilers, geysers, water heaters - Repair, service, operation. Recommendations for installation and installation. Magnesium anode included in warranty

My Atlantic Steatite Slim VM 80 boiler is 3.5 years old. After 2 years, brown liquid came out of the hot pipe, I took it apart to see what was going on. It turned out that the anode had fallen off and raised turbidity from the bottom of the tank (my water from my well, despite the filters, has a little bit of clay coming through). I put it in place and continue to use it. After another 1.5 years, I bought a new anode and wanted to put it in the EWH. I disassembled the device, and the anode was completely worn out. I also raked out a couple of handfuls of husks from the tank - the enamel was crumbling, the upper part was simply rusty, there was no enamel. As I understand it, I’ve already been living with a rusting tank for about six months. How long will it last in such conditions - should I already run to buy something new, or do I still have six months? A pair of leads - all on one flange - that's what you need! I have it suspended from the ceiling, there is no way to climb from above, from below there are still pipes and a handle. The thermometer is still useful, as is the regulator - sometimes you need more water- you can (temporarily) turn up the thermostat to maximum (usually it’s set to 3/4). You still need to clean the tank or heating element once a year/year and a half. If there are signs of wear, definitely change the anode.

By shedding of enamel. We need to figure out the reason. Either the safety valve was missing, or the hydraulic accumulator is missing (failed) and water hammers occur when the pump is turned on. In general, you need to check the water supply system. In any case, massive shedding of enamel indicates the presence of excess pressure inside the water heater.

The Atlantic storage water heater has 80 liters of heating element, as I understand it, 2 kW? This is good. And what do they write about additional protection? Judging by the advertisement, some potential is applied to the anode. This electrochemical protection? Tell me one more thing - how safe is it to raise the temperature to the maximum?

The factory setting on most thermostats is 70-75 degrees. Over time, it changes upward. There is an opinion that heating at maximum temperature is bad. I believe that you need to heat it the way you want. That's why it's technology, to exploit it. In addition, the higher the water heating temperature, the less bacteria grows inside the water heater.

I have a savings account boiler Atlantic Steatite Cube VM 100 S4CM, steatite (dry) heating element. Dual-mode 1.2 kW and 2.4 kW. It has 2 thermostats: protective and regulating heating temperature. Worked for 2 years in 2.4 kW mode at maximum heat. Breakdown: first the protective thermostat started to break down. Then the attachment point melted in it neutral wire. Replaced the thermostat with a new one. Now, in the 2.4 kW mode, the mounting wires inside become very hot, both neutral and phase. In 1.2 kW mode they do not heat up. 4 square copper wires go from the 16A machine to the boiler. These wires don't get hot. What could be the reason for overheating of the wires inside the unit, given that the contacts are all connected tightly and not loose?

Unfortunately, we do not have the opportunity to advise on such highly technical issues remotely, since everything needs to be checked on the spot; it is recommended to call a specialist.

I have an Atlantic 50 liter electric water heater, it has worked perfectly since 2007, but one evening I noticed that water was dripping from it. Please advise how to fix this (if possible), or call specialists?

If there is leakage through the gasket, replace it.

Boiler Atlantic Round Standard 50. The problem is that it heats the water to strong boiling water and for some reason does not turn off automatically for about 4 hours. The temperature sensor on the case indicates above average, although it is set to minimum. Is this the norm? Or a thermostat failure?

No, this is not the norm, most likely the problem is in the thermostat, but other malfunctions are also possible, for example, the temperature sensor could have failed. An examination is necessary for an accurate diagnosis.

Is it possible to connect an electric boiler and an 80-liter Atlantic boiler into one combination? Theoretically, I myself understand that I cannot do this when I looked at the connection diagram. Why do I want this? So that all electrics are connected to one place, and the boiler controls the heating process of itself and the water heater. For example, you need to set the heating time for the boiler, and at this time the boiler turns off the heating and heats the EWH at full power.

This is an electric water heater. It can only be “connected” to the boiler by wires. In a sense, both it and the boiler have a certain electrical power. The boiler you are planning is 6 kW, the EWH is 2.4 kW. Do you have this allocated 10 kW (at least turn on the kettle) of electrical power? There is an option to heat hot water in a boiler indirect heating using an electric boiler. Double benefit - less allocated power is needed and the water heats up much faster.

If water flows from under the inner blue plastic that the pipeline goes into cold water, what should be done in this case? Boiler Atlantic series Opro VM 100.

You need to install exact location leaks, pipes and connections can be replaced, repairing a leaking tank is usually not cost-effective and does not last long. If the leak is not large, condensation is possible.

Tell me, in Atlantic models Does Vertigo Steatite 50 have an overpressure relief valve? And is there a heating indication, a light that lights up when the water heating process begins, and goes out after the heating element is turned off. I just heard about water heaters exploding, and you need to keep an eye on that on/off indicator. heating element (heating element). And also, if you use this heater only in summer, and occasionally in winter (for example, on new year holidays) and then drain all the water and disassemble the device, is there still a high probability of breakdown?

A safety valve is included. There is an indicator light that will show you whether the machine is heating up or not. For the winter you will have to disassemble and drain the water, otherwise it will not drain completely.

Atlantic Steatite Slim VM 80 l. and Elite 80 l. They differ, among other things, in the power and presence of a magnesium anode in Slim. As far as I understand, with a dry heating element the absence of a magnesium anode is not critical. But the power for country house Is it better to have less, about 1500, so that it doesn’t get knocked out?

The presence of an anode is mandatory, the tank is steel and covered with enamel. The manufacturer requires checking the condition of the anode every 1.5-2 years. The question is what will hold up or not. You need to look at how much power is allocated to the house and consider the entire connected load.

I want to buy an Atlantic electric storage water heater 100 liters S4CM. What can you say about him?

Dry heating element, warranty on tank 7 years, on electrics 2 years. Ideal for hard water.

At the dacha (one small house) costs pumping station. Its water maintenance thresholds are from 2 to 3 atmospheres (on - off). I installed an Atlantic Ego 50 boiler. My brother had it for a long time, but was rarely used. The unit is working. The check valve was checked and cleaned - it is in good working order. Unfortunately, there is no data sheet for it, but judging by the brackets, it can be installed both vertically and horizontally. I installed vertically, the top inlet on the boiler with the blue end (with check valve connected the cold water inlet to it), the lower one with a red ring (directly the hose to the water sockets). The rings on the boiler are non-removable, that is, no one has mixed them up. The nameplate on the device with markings and other data in this position is readable directly, which also indicates its correct position. At the bottom of the unit there was a temperature regulator with a power-on indication (mechanical thermostat and neon indicator lamp) and a cord for connecting to the outlet. That is, logically, turning it upside down contradicts the meaning (it is impossible to adjust and the indication is not visible). But then it turns out that it has an upper inlet for cold water, and a lower outlet for hot water. With the mixers turned off (even the taps on the water sockets are all closed), when the device heats up, after 2-3 hours the cold main heats up very much. Even the hose overheated high pressure pump that goes into the well. During subsequent inspection, purely visually by hand, the inlet of the cold hose is even hotter than the outlet of the hot one. Questions: Is this a universal unit (vertical-horizontal)? If it is vertical, then, contrary to logic, it is necessary to place the indicator and regulator at the top (so that the blue water intake is at the bottom)? Or is it still horizontal? Or do you still need to install something?

Is the valve itself correct? If it is working properly and installed correctly, in any case, hot water should not pass through it. Well, maybe a little, if it works. Vertical model, indicator and regulator at the bottom. You need to completely fill the device (you need taps on both pipes), disconnect it from the system and open both taps. There will be a global gush from the first, and air will be sucked into the second. The first is the cold water inlet, the second is the hot water outlet.

What is the device and principle of operation storage water heater Atlantic Steatite Exclusive 200?

Conventionally, all models, the installation of which is best left to specialists, can be divided into two types: “Dry” - steatite heating elements in flasks; “Wet” - copper heating elements without flasks.

How do “dry” steatite heating elements differ from steel tubular heaters that are used by other manufacturers in “dry” models?

Soapstone is an ideal natural material for electrical equipment. He's very tall physical characteristics, mechanical strength and stability. Soapstone can withstand temperatures above 1000C, does not burn and has excellent thermal conductivity. Compared to steel heaters, soapstone elements have a larger heat transfer area, which allows them to heat water faster. They heat up almost instantly and take a long time to cool down, which has a beneficial effect on the energy efficiency of the EWH.

How many liters hot water does the Atlantic water heater leave 100 liters?

When drawing water from a hot tap at the point of consumption, the volume of water heated to the maximum temperature will be about 3/4 of the total volume of the device. The remaining 1/4 part is water from the layer where mixing of heated water and incoming cold water occurs. The amount of hot water coming out depends on the intensity of the flow through the EWH and the temperature of the incoming water.

Why in cold period does the heating time increase every year?

This is due to a decrease in the temperature of the incoming cold water supply.

What is the maximum water heating temperature?

Maximum temperature heating 63±30 C.

Why is there no scale on the temperature gauge?

The temperature indicator is designed to display the process of heating or cooling water in the device. It is not an accurate measuring instrument.

Is it necessary to disconnect the Atlantic 50 liter boiler from the power supply after each heating?

No. The unit operates in automatic mode. When the temperature set on the thermostat is reached, the contact opens and the voltage is removed from the heating element, the device turns off. When cooling, the contact closes and voltage is applied to the heating element.

What is the energy consumption during operation? electric water heater Atlantic Vertigo Steatite 100?

The amount of electricity consumed depends on the intensity of operation of the device, as well as the temperature of the cold liquid entering it.

What is the safety valve for in the 80 liter Atlantic model? Why is it dripping?

The safety valve is designed to prevent liquid from flowing out of the tank if there is no liquid in the cold water supply riser, as well as to relieve excess pressure formed in the tank during the expansion of heated water. Pressure is released by releasing a small amount of it from a special hole when the pressure in the tank reaches 8 atm. Installation of the valve supplied with the device is mandatory.

How much volume can be discharged from the safety valve relief port on the Atlantic Steatite Elite 80?

This depends on the intensity of operation - the more often the device is turned on for heating, the large quantity liquid will be discharged. It also depends on the pressure in the cold water supply riser - the higher the pressure in the riser, the less time it takes to reach the pressure in the tank at which the discharge occurs.

The model Steatite Cube 100 is in operation. Why is a magnesium anode needed and why should it be replaced periodically?

The purpose of the magnesium anode is to increase reliability and improve operating conditions of the unit by protecting the steel tank from corrosion and preventing the formation of dense scale deposits on the copper heating element. The protection of a steel tank from corrosion lies in the fact that during the electrochemical interaction of several metals in an aqueous solution, corrosion of the metal with a lower electrode potential occurs. In the device, the copper heating element has the highest potential, then comes the steel tank and then the magnesium anode, which is subject to destruction (corrosion). When the anode is completely destroyed, the steel tank is exposed to corrosion. That is why a spent magnesium anode must be promptly replaced with a new one.

What is the frequency of replacing the magnesium anode for an Atlantic boiler?

The replacement frequency for models N4E, N4, PC, S3S, D400-1-M, Round VMR, Delfa N4L, Aston, Welcome is 12 months. When using the device in production, services and places Catering- 6 months.

Electric boilers are good because they are quite simple to use - just connect them to the power supply. Moreover, they are safe and effective. The French manufacturing company Atlantic confidently holds the lead among manufacturers of this type of water heaters, offering consumers products of excellent quality and design.

High-quality Atlantic water heater and its advantages

The French company Atlantic, which produces boilers for heating water, is quite popular among consumers. This is due to the fact that this company has been on the market for quite a long time and has proven itself to be the best.

Atlantis heating devices are manufactured in cylindrical and square shapes. These devices are most often used in apartments and private houses.

Advantages of using Atlantic boilers:

Quite affordable price;
Fast water heating;
Corrosion resistance;
Economical;
Wide selection of models for every taste;
Stylish design that can suit almost any room interior.

However, annual cleaning will help to avoid the latter, for which you can call a specialist, and the problem will be solved.

Before you decide to buy a water heater from any company, you should understand what they are like and understand the nuances of their operation.

The Atlantic water heating tank can be:

Horizontal– in this case, the heating element of the device is located on the side, and the water inlet pipes are located very close, so the liquid is mixed in the structure itself, which can cause sudden temperature jumps at the outlet. But at the same time, such models are compact and can be placed under the ceiling, thereby not taking up much space.
Vertical- costs less than horizontal. The heating element is located at the bottom of the unit, where the cold flow of liquid enters. Thanks to this, the water is heated faster.

Atlantic heaters can have a dry heating element enclosed in a special flask or submersible.

In order not to make a mistake in choosing a unit, you should consider:

The need for heated liquid, which directly depends on the number of its consumers. For example, the average amount of water for bathing one person in a shower stall is approximately 30-50 liters, and about 20 liters are needed for washing dishes and hands.
Device power and its compliance permissible load networks. To heat the water as quickly as possible, models with a power of 2-2.5 kW are often taken. But if you have old wiring in your house, you shouldn’t go too fast. It is better to take a 1.2-1.5 kW unit, however, the heating time will increase.
Device location. If there is little free space in the room where you plan to install the unit, it is better to choose a horizontal model.
Water quality. If it is too hard, then the tank will have to be cleaned frequently due to scale appearing on its walls, which shortens the service life of the device.

When choosing a water heater, Special attention you need to pay attention to the volume of the container. A 50-liter tank is enough for one person or a couple who is at home mostly in the evening. 80 liter tanks are larger and more spacious. They are convenient to purchase for a family of 2-3 people who are often at home.

The 100 liter boiler can be connected to different liquid supply points, allowing them to be used simultaneously. This volume is easily enough for 3-4 people. The instructions will help you figure out how to connect the device.

It is not advisable to purchase equipment in inappropriate places or in points where there are no certificates of compliance with GOST.

Popular Atlantic water heater: model range

If you decide to purchase an Atlantic boiler, it is worth studying the popular models of these water heaters to determine what you need.

Today there are three common lines of these boilers:

Classic– very affordable water heaters. Their design consists of a copper heating element and a magnesium solution in the tank, which prevents the formation of corrosion. But, nevertheless, cleaning is still necessary.
Advanced– this series is characterized by a ceramic heating element with a submersible heating element. These models are in good demand among consumers and, as a rule, receive only positive reviews.
Premium– as the name suggests, heaters in this line are available at more high price. This is due to the presence in the system of a titanium anode, a ceramic heating element and a special anti-corrosion coating.

Like any other equipment, Atlantic boilers can fail. In this case, it is better not to try to do the repair yourself, but to call a specialist who can competently and quickly repair your equipment.

Atlantic boiler 80 liters: what is good about a dry heating element

Atlantic water heaters can be equipped with either submersible or dry heating elements. Moreover, the latter are considered more popular models. Why does this happen?

Advantages of dry heating element:

Longer service life - this is due to the fact that it is enclosed in a special flask and does not come into contact with the liquid, and therefore is not affected by it;
No scale on the element;
No need to carry out regular cleaning device or use any means to improve the functioning of the unit;
The cost of a dry heating element is cheaper than a “wet” one.

By the way, if a dry-type heating element breaks, getting to it will be quite easy. And you won’t have to spend a lot of time searching for a replacement or repairing a part.

And yet, despite the undeniable advantages, a water heater with a dry heating element has one drawback - the water in such a boiler heats up rather slowly, since the heating element is located in a separate container, and not in the water.

Features of the Atlantic boiler (video)

If the quality of the device comes first for you, then you should pay attention to Atlantis boilers. They are reliable, durable, comfortable and easy to use. Thanks to the wide range of manufactured models, you can choose exactly the device you need.

Atlantic water heaters - Tips for operation, repair and troubleshooting

Tell me, does the Atlantic Vertigo Steatite 50 model have a safety valve against overpressure? And is there a heating indication, a light that lights up when the water heating process begins, and goes out after the heating element is turned off. I just heard about water heaters exploding, and you need to keep an eye on that on/off indicator. heating element (heating element). And also, if you use this heater only in the summer, and occasionally in the winter (for example, on New Year’s holidays) and then drain all the water and disassemble the device, is there still a high probability of breakdown?

Atlantic Steatite Slim VM 80 l. and Elite 80 l. They differ, among other things, in the power and presence of a magnesium anode in Slim. As far as I understand, with a dry heating element the absence of a magnesium anode is not critical. But for a country house it’s better to have less power, about 1500, so as not to knock it out?

I want to buy an Atlantic electric storage water heater 100 liters S4CM. What can you say about him?

Dry heating element, warranty on tank 7 years, on electrics 2 years. Ideal for hard water.

The Atlantic storage water heater has 80 liters of heating element, as I understand it, 2 kW? This is good. And what do they write about additional protection? Judging by the advertisement, some potential is applied to the anode. Is this electrochemical protection? Tell me one more thing - how safe is it to raise the temperature to the maximum?

I have a storage boiler Atlantic Steatite Cube VM 100 S4CM, steatite (dry) heating element. Dual-mode 1.2 kW and 2.4 kW. It has 2 thermostats: protective and regulating heating temperature. Worked for 2 years in 2.4 kW mode at maximum heat. Breakdown: first the protective thermostat started to break down. Then the place where the neutral wire was attached melted. Replaced the thermostat with a new one. Now, in the 2.4 kW mode, the mounting wires inside become very hot, both neutral and phase. In 1.2 kW mode they do not heat up. From the 16A machine to the boiler they go copper wires 4 squares. These wires don't get hot. What could be the reason for overheating of the wires inside the unit, given that the contacts are all connected tightly and not loose?

Unfortunately, we do not have the opportunity to advise on such highly technical issues remotely, since everything needs to be checked on the spot; it is recommended to call a specialist.

If there is leakage through the gasket, replace it.

This is an electric water heater. It can only be “connected” to the boiler by wires. In a sense, both it and the boiler have a certain electrical power. The boiler you are planning is 6 kW, the EWH is 2.4 kW. You have this allocated 10 kW (at least turn on the kettle) electrical power? There is an option to heat hot water in an indirect heating boiler using an electric boiler. Double benefit - less allocated power is needed and the water heats up much faster.

If water is leaking from under the inner blue plastic that contains the cold water pipe, what should you do in this case? Boiler Atlantic series Opro VM 100.

It is necessary to establish the exact location of the leak, the pipes and connections can be replaced, repairing a tank leak is usually not cost-effective and short-lived. If the leak is not large, condensation is possible.

At the dacha (one small house) there is a pumping station. Its water maintenance thresholds are from 2 to 3 atmospheres (on - off). I installed an Atlantic Ego 50 boiler. My brother had it for a long time, but was rarely used. The unit is working. The check valve was checked and cleaned - it is in good working order. Unfortunately, there is no data sheet for it, but judging by the brackets, it can be installed both vertically and horizontally. I installed it vertically
the top inlet on the boiler with a blue end (with a check valve connected to the cold water inlet), the bottom with a red ring (the hose goes directly to the water sockets). The rings on the boiler are non-removable, that is, no one has mixed them up. The nameplate on the device with markings and other data in this position is readable directly, which also indicates its correct position. At the bottom of the unit there was a temperature regulator with a power-on indication (mechanical thermostat and neon indicator lamp) and a cord for connecting to the outlet. That is, logically, turning it upside down contradicts the meaning (it is impossible to adjust and the indication is not visible). But then it turns out that it has an upper inlet for cold water, and a lower outlet for hot water. With the mixers turned off (even the taps on the water sockets are all closed), when the device heats up, after 2-3 hours the cold main heats up very much. Even the high pressure hose of the pump that goes into the well overheated. During subsequent inspection, purely visually by hand, the inlet of the cold hose is even hotter than the outlet of the hot one. Questions: Is this a universal unit (vertical-
horizontal)? If it is vertical, then, contrary to logic, it is necessary to place the indicator and regulator at the top (so that the blue water intake is at the bottom)? Or is it still horizontal? Or do you still need to install something?

What is the design and principle of operation of the Atlantic Steatite Exclusive 200 storage water heater?

How do “dry” steatite heating elements differ from steel tubular heaters that are used by other manufacturers in “dry” models?

Soapstone is an ideal natural material for electrical equipment. It has very high physical characteristics, mechanical strength and stability. Soapstone can withstand temperatures above 1000C, does not burn and has excellent thermal conductivity. Compared to steel heaters, soapstone elements have a larger heat transfer area, which allows them to heat water faster.
They heat up almost instantly and take a long time to cool down, which has a beneficial effect on the energy efficiency of the EWH.

How many liters of hot water comes out of a 100 liter Atlantic water heater?

Why does the heating time increase during the cold season?

This is due to a decrease in the temperature of the incoming cold water supply.

What is the maximum water heating temperature?

Maximum heating temperature 63±30 C.

Why is there no scale on the temperature gauge?

The temperature indicator is designed to display the process of heating or cooling water in the device. It is not an accurate measuring instrument.

Is it necessary to disconnect the Atlantic 50 liter boiler from the power supply after each heating?

What is the energy consumption when operating the Atlantic Vertigo Steatite 100 electric water heater?

The amount of electricity consumed depends on the intensity of operation of the device, as well as the temperature of the cold liquid entering it.

What is the safety valve for in the 80 liter Atlantic model? Why is it dripping?

How much volume can be discharged from the safety valve relief port on the Atlantic Steatite Elite 80?

This depends on the intensity of operation - the more often the device is turned on for heating, the greater the amount of liquid will be discharged. It also depends on the pressure in the cold water supply riser - the higher the pressure in the riser, the less time it takes to reach the pressure in the tank at which the discharge occurs.

The model Steatite Cube 100 is in operation. Why is a magnesium anode needed and why should it be replaced periodically?

The purpose of the magnesium anode is to increase reliability and improve operating conditions of the unit by protecting the steel tank from corrosion and preventing the formation of dense scale deposits on the copper heating element. The protection of a steel tank from corrosion lies in the fact that during the electrochemical interaction of several metals in an aqueous solution, corrosion of the metal with a lower
electrode potential. In the device, the copper heating element has the highest potential, then comes the steel tank and then the magnesium anode, which is subject to destruction (corrosion). When the anode is completely destroyed, the steel tank is exposed to corrosion. That is why a spent magnesium anode must be promptly replaced with a new one.

What is the frequency of replacing the magnesium anode for an Atlantic boiler?

The replacement frequency for models N4E, N4, PC, S3S, D400-1-M, Round VMR, Delfa N4L, Aston, Welcome is 12 months. When using the device in production, in the service sector and public catering establishments – 6 months.

__________________________________________________________________________

_______________________________________________________________________________

OPERATION AND REPAIR OF BOILERS

Proterm Panther Proterm Skat Proterm Bear Proterm Cheetah Evan
Ariston Egis Teplodar Cooper Atem Zhytomyr Neva Lux Arderia Nova
Termona Immergaz Electrolux Conord Lemax Galan Mora

Electric boilers from the French brand Atlantic are characterized by a successful combination prices and quality. They are represented by a limited number of models with tank volumes up to 200 liters. The Atlantic boiler will become smart choice for the thrifty buyer. Its purchase will not break your pocket, and its carefully thought-out design will ensure a long service life of the device.

Varieties and features

The French brand "Atlantic" presented three main types of boilers for users to choose from:

Electric - use only electricity for power.
Indirect heating - heat is taken from heating systems.
With heat pumps – an environmentally friendly series that uses heat from the environment to heat water.

In our review we will touch on electrical and indirect boilers"Atlantic". Will be considered as simple models, made in cylindrical cases, and designer ones, characterized by high-quality appearance and thoughtful ergonomics. Their production uses the developer's proprietary technologies - Diamond-Quality tank protection, Smart control Control, Steatite dry heating elements, ACI Hybrid and O’Pro corrosion protection technologies. They allow us to produce reliable and durable water heaters.

Popular models

Let's move from words to action and consider the most interesting and popular models. These include water heaters of 10 and 100 liters, designer samples, products with powerful protection tanks, as well as devices with dry heating elements. Along with descriptions of Atlantic boilers, their detailed technical characteristics will be given.

"Atlantic" O'Pro Small PC 10 RB

The overview opens to a tiny water heater with a volume of 10 liters. Its tank is enclosed in a barrel-shaped body and equipped with protective coating from glass ceramics. Behind additional protection A magnesium anode is responsible for preventing rust on welds. The power of the heating element is 2 kW, which ensures fast water preparation. Distinctive feature device – possibility of operation in rooms with increased level humidity.

The Atlantic water heater O’Pro Small PC 10 RB heats water to a temperature of +65 degrees and withstands pressure up to 8 atmospheres. The heating time to the maximum mark is 19 minutes. The boiler is well suited for dacha exploitation and will help out during periods of outage of hot water supply in big cities. Estimated cost baby is 4500 rubles.

In front of us is an 80-liter Atlantic boiler - this volume is enough for a family of 2-3 people. Key Feature models – dry steatite (ceramic) heating element. To protect against corrosion, Diamond-quality technology is used, which involves applying inner surface tanks of special enamel, resistant to corrosion. The water heater is installed in two positions - vertical or horizontal. It does not take up much space, as it is made in a thin elongated body.

Responsible for quick preparation of hot water heating element power 2.1 kW. It copes with its task well, which is confirmed by user reviews. The maximum heating level is +65 degrees with a pressure in the tank of up to 8 atmospheres. The control system used is mechanical, with a power-on indicator, a thermometer and a heating limiter. Approximate price in Russian online stores – 10-11 thousand rubles.

"Atlantic" Steatite Elite 100

Atlantic water heaters with dry heating elements are characterized by increased heater resistance to corrosion. For this heating elements are dressed in protective housings, which prevents their contact with water and further destruction. The presented model is made using exactly this technology and has a capacity of 100 liters. The time for heating water to the maximum level is 246 minutes - this is a lot. The whole point is that the heating element is too low - its power is only 1.5 kW.

The storage boiler tank is protected by a durable glass-ceramic coating and equipped with a magnesium anode. Several degrees of protection make it resistant to corrosion, which does not spare even the most durable alloys. The volume is enough for any need - washing dishes, taking a shower, washing hands. The approximate cost of the model from the French brand "Atlantic" is 11.5 thousand rubles.

"Atlantic" Ingenio VM 080 D400-3-E

Before us is a typical Atlantic boiler for 80 liters of water. It has the following characteristics:

Advanced electronic control with Smart Control energy saving system.
O'Pro passive anti-corrosion system.
Convenient control of parameters with a liquid crystal display.
Adaptive control of water heating.
Glass-ceramic tank protection.
The power of the heating element is 2 kW (not dry).

The boiler is mounted on the wall in vertical position, piping is done from below. The weight without water is 22 kg, which reduces the load on the walls. For the convenience of users, the 80-liter Atlantic water heater was supplemented with the function of accelerated water heating - the maximum temperature level is +65 degrees. The pressure in the tank should not exceed 8 atmospheres. Buy this model in domestic online stores you can get it for only 8,500 rubles.

"Atlantic" Vertigo 80

The 65-liter Atlantic Vertigo storage boiler is made in a vertical rectangular body that fits optimally into any design. The developers equipped the device with a double steatite heating element of increased power - 2.25 kW, the function quick preparation water for showering (heats up in 30 minutes). Thanks to the resistance of the heating element to corrosion, the boiler can operate with high water hardness levels.

This advanced model is equipped with convenient electronic control with the Smart Control energy saving system. It’s easy to select and control the temperature and enable additional options. The system itself adapts to water consumption, choosing the most economical operating modes. The boiler is mounted in both vertical and horizontal positions. The time for heating water to maximum is 79 minutes. To implement the quick heating function, the internal tank is divided into two parts.

Stylish slim body, high power protected heating element, advanced system electronic control- all this influenced the cost of the Atlantic water heater. Its price in stores is 18-20 thousand rubles.