Replacing lighting bulbs with your own hands. How to replace a light bulb in various lamps.

One of the most common problems with room lighting is a burnt out lamp. Considering different variants overhead lighting, the question is how to change the light bulb in ceiling chandelier, the lamp does not look light.

The non-working state of one of several light bulbs is not a reason to immediately take on a shift. It is more convenient and safer, if possible, to pull the lamp out naturally. daylight. And if you have to disassemble the illuminator at night, you need a flashlight. Tools you may need are pliers, a screwdriver, and it’s a good idea to wear cotton or rubberized gloves.

The electricity supply should be turned off at the work site. You can turn off the machine or use the key switch.

A new light element - preferably completely similar to the burnt one - should be on hand to screw it in without delay.

Note

The possibility of marriage should never be ruled out. Therefore, when you turn on the light for the first time, it is better not to stand under a chandelier or lamp, and even more so, not to immediately raise your head up. It is better to exclude the possibility of injury if the new lamp does break.

Installing an incandescent lamp

Incandescent lamp general purpose 230 V, 60 W, 720 lm, E27 base

Before changing the light bulb, it is advisable to remove the lampshade and frame. After this, holding the socket with one hand, unscrew the lighting element in a counterclockwise direction.

If the bulb is cracked, it should first be wrapped in cloth and then removed from the cartridge. Lower your head down so as not to hurt your eyes, put on glasses. If the glass explodes, the remains are also removed using a soft cloth, rags, and only pliers will help to unscrew the base.

It also happens that after unscrewing, the glass remains in the hand, and the base remains in the socket. Then you can't do without pliers.

Now you can make a replacement. The new lamp is screwed in clockwise until the end. There is no point in trying to screw it in harder: it will only damage the flask.

Installing an energy-saving light bulb

An energy-saving lamp consists of 3 main components: a base, a fluorescent lamp and an electronic unit.

An energy-saving lamp differs from an incandescent lamp in structure - the bulb is replaced by a fluorescent tube. It is easier to change a burnt-out energy-saving element - there is a choke located next to the screw-in base, so it can be changed simply by pulling it out.

Changing light bulbs in a suspended ceiling

In a room with a suspended ceiling, the role of a light source can be played by both chandeliers and recessed lamps that are directly mounted on the base.

Before changing a lamp - LED, halogen or fluorescent - you need to choose one that is suitable in terms of power and installation for a particular spotlight. And for this you need a packaging box or a burnt-out lamp itself.

How to change a light bulb in a suspended ceiling? Since the body of the built-in light source is secured by spacers with two springs, it is quite possible to pull it down a little, carefully holding the lamp on both sides. You need to pull it out of the frame to a length sufficient to unscrew the screw base. When the work lamp is screwed in, the lamp returns to its place in this way: the springs are pressed against the base, inserted back, then into the hole tension structure the housing itself is inserted.

Spotlights and chandeliers are attached to the ceiling itself, and the hanging canvas forms only a cell. However, the recessed lights themselves differ slightly in design from chandeliers. And first of all, this concerns the base. The fact is that the thread of the cartridges for built-in illuminators is not the same in size. In addition, there are pin sockets. Therefore, the method of replacing a light bulb from a spotlight also depends on the type of mounting.

Types of fastening in lamps

So, there are three types of fastening: standard with thread, pin and rotary .

At standard mount- in a threaded socket, - changing a chandelier on a suspended structure is similar to replacing a lamp on a non-suspended, base ceiling.

The pin type has a different extraction mechanism - it has a ring for a stopper. Such a base - usually two-pin - is found in halogen ones.

How to change halo new light bulb? To remove a halogen lamp, the ring is squeezed and pulled out - the lamp will remain hanging on the wires. All that remains is to disconnect it from the terminal, pull it out forcefully, then insert a new one - there should be a characteristic click - and secure it with a locking ring.

Halogen lamps with a two-pin base are installed with cotton gloves, otherwise the bulb may explode. In addition, fingerprints that are difficult to erase may remain on the flask. But when working with such a lamp, you do not need to remove the lamp from the frame.

There is another type of cartridge - special - this is what fluorescent and LED illuminators most often have. This type of fastening contains both a fixing ring, which is removed first, and a thread. After the ring, the glass part is removed - and the burnt-out part can be removed. This mount is called a rotary mount, because to fix the lamp, it must be rotated 90º.

Doing major renovation in a house or apartment, consumers are increasingly choosing suspended ceilings. This design allows you to radically change the interior of any room and hide numerous defects. Any type of suspended ceiling, including Armstrong, is most often illuminated by built-in lamps, and, unfortunately, sooner or later the lamp in the lamps has to be changed. If the suspended structure was assembled by the owner of the property, then replacing an element that has become unusable will not be difficult. And if this work was performed by a special construction company, then you will have to solve this problem yourself. In this article we will tell you how to change a light bulb in a suspended ceiling quickly and safely.

Types of lamps for suspended ceilings

Before you start replacing an unsuitable element, you should familiarize yourself with the types of lamps that are used in a suspended ceiling structure:

standard incandescent lamps. This option is probably known to everyone, so the replacement process will not cause difficulties;
energy-saving lamps. Even judging by the name, you can understand that this option consumes the least amount of electricity. However, their service life is very limited. The more often such a lamp turns on and off, the less it will serve its owner. In addition, in a room with high humidity, for example, in a bathroom or shower, experts do not recommend installing an energy-saving light source;
having installed LED lamp, you can give the hanging structure a unique chic and originality, and create beautiful panoramic lighting. In addition, this option is the most durable and reliable;
a halogen lamp is best perceived by the human eye, moreover, it can be used in any room, including those rooms in which there is constant observation high humidity. However, if you decide to use a halogen lamp in a pendant structure, you should know that this option quickly fails if there are sudden voltage surges in the network. A voltage stabilizer, which experts recommend installing additionally, will help solve this problem.

Components of the structure

Before replacing a lamp that has become unusable, you need to familiarize yourself with the design of this element.

The main components, regardless of the type of lamp, are the following:

a housing that includes the lamp socket and wires;
a clamp with which the device is fixed to a suspended structure;
a protective cover, the basis of which can be either plastic or glass;
rings for fixation.

Knowing what components the design of shelf lamps consists of, it will be much easier to replace an element that has become unusable.

The most popular element for modern suspended ceilings is a spotlight. They differ from other types of lighting fixtures in their wide variety design design, and they can work with any type of light bulb. With the help of such lamps you can perfectly complement the interior and highlight its features. Over time, it becomes necessary to completely remove the lamp from the ceiling. And the most common reason for this is replacing a light bulb. Now we will learn how to change a light bulb in a spotlight yourself. You need to seriously prepare for this, because working with electrical appliances is very dangerous and can lead to disastrous consequences.

How to replace a light bulb in a suspended ceiling?

If your light bulb suddenly fails, you need to replace it immediately so as not to disrupt the operation of the overall lighting system. But not everything is so simple here, since first you need to remove the lamp itself from the socket and only then the light bulb. Depending on the type of lamp, you need to perform different steps to replace it.

So, first we’ll find out how to remove a lamp from a suspended ceiling in order to replace the lamp:

First of all, turn off the light in the room, unscrew the part that holds the parts of the lamp together, and remove it from the socket piece by piece.
If you use ordinary incandescent light bulbs, you need to unscrew old lamp and put a new one in its place.

If you need to replace a halogen light bulb, you will have to spend a lot of effort. First we do the same as in the first case, turn off the power supply, remove the cover from the lamp and remove the retaining ring.

Important! Remember that halogen lamps should only be removed with the help of napkins or gloves. The fact is that fat soaking the fingers can shorten the service life of these products.

There are situations when lamps represent a single mechanism with light bulbs, and then you have to completely change the entire lamp.

How to change an LED lamp in a suspended ceiling?

Because exactly LED lights Nowadays they are the most convenient and profitable, they are used everywhere. In addition, they consume a minimum of electricity, work properly for several years and shine very brightly. But nevertheless, even such light bulbs can fail. Therefore, you must definitely figure out how to insert an LED lamp into a ceiling lamp, if suddenly old model will burn out.

Replacing such devices occurs in several stages:

You need to take a new lamp and check its serviceability using a tester.
The electricity in the room must be turned off.
Take care of autonomous lighting, because you definitely won’t be able to do anything blindly.
Remove the holder from the burnt-out light bulb.
The insulation must be removed from the wiring.
Then disconnect the wires.
Read the instructions that came with the new light bulb.
Install the device according to the instructions.
Return all wires to their places and restore the insulation of the electrical wires.
Remove the wires and attach the lamp cover.
Attach the cover to the box using screws.

How to properly remove a chandelier from a suspended ceiling?

In fact, even an inexperienced person can figure out how to remove a ceiling light or chandelier on their own. If you are very afraid of electric shock, then you can turn off the power to the entire apartment, since this will completely protect you, and you will complete the procedure calmly, quickly, without unnecessary worries.

The chandelier is removed from the stretch ceiling in the following sequence:

Chandeliers hung on a hook are easy to remove. First you need to delete protective cap, put your hand into the hole formed, then feel for the hook on which the chandelier hangs. You should grab it as tightly as possible in this place and remove it along with the wiring. But we still work carefully with the wires, even though they are de-energized. Carefully remove the insulation and disconnect all wires from each other. All is ready!
To dismantle a lamp mounted using a cross-shaped strip, you need to perform several more steps. It is necessary to remove all elements from the lamp: shades, lamps, decorative parts. Then unscrew the cap, under which the fastening system is hidden. Unscrew the hangers by unscrewing the screws and pull out the chandelier directly with the fastening element. Now remove the insulation and unwind the wires. The chandelier is free!

Important! If your chandelier is too massive, then do not try to remove it yourself; it is better to invite an assistant to help you during dismantling.

How to remove a spotlight from the ceiling yourself?

When removing a point electrical appliance, both small and quite serious problems, because not everyone knows how to remove a spotlight from a stretch ceiling correctly. If you first study the scheme for carrying out this work, you can avoid all this. In addition, you need to be extremely careful so that you do not accidentally get electrocuted.

When removing such lamps, the following problems arise:

The springs that secure the lamp to the ceiling hit your fingers hard when you pull it out.
There is a possibility of getting an electric shock.
When pulling out the lamp, springs that are too strong can damage the strobe.

So, to prevent all the problems listed above, you need to remember the basic safety rules:

Always turn off the electricity before dismantling lighting fixtures;
Be sure to hold the springs as tightly as possible to protect the ceiling and fingers from damage.

Now you know how to disassemble a spotlight and change the bulb in it. Therefore, from now on you can not be afraid of difficulties in working with lighting fixtures, because it is better to replace a failed element than to leave it in the ceiling inoperative. Agree that there is no point in being original and beautiful suspended ceiling With fashionable lamps, if they do not shine and perform their functions. Faulty products will only spoil the mood with their presence.

The light source plays a very important role in our life, and modern man feels terrible discomfort with his absence. The problem of light bulb failure is the simplest and most common. electrical fault. To quickly restore the lack of light, you need to know how to change light bulbs.

Installation locations and the light bulbs themselves are currently so diverse in design, power consumption and required voltage, material, operating principle. All these characteristics need to be known when replacing the lamp.

It is advisable to change light bulbs during the day if there is a sufficient source natural light. To replace, you will need pliers with insulated handles, a screwdriver, a flashlight (for working in dark rooms - pantry, bathroom, basement), a replacement light bulb, and rubber gloves.

Before changing the light bulb, it is necessary to de-energize the power supply section (turn off circuit breaker in the electrical panel or unscrew the plugs). Replacing a light bulb involves removing some parts of the lamp structure (shades, protective frames).

Incandescent lamp

The burnt-out light bulb is unscrewed counterclockwise with one hand, and the socket is fixed with the other hand. How to change light bulbs, if in many cases the bulb of an incandescent lamp can become damaged (crack, “explode”) and become detached from the socket. In this case, holding the cartridge with your hands, remove the remains of the flask using a rag. Eyes must be protected with goggles. Base old light bulb Unscrew it with pliers. This will protect your fingers from damage and will add force to the base if it is screwed in tightly or “stuck.” The replacement bulb is screwed in clockwise until it stops. There is no need to be very zealous, as you can damage the flask.

Energy-saving lamps

The design of the energy-saving lamp has a standard Edison base, and instead of an incandescent lamp bulb, it has a compact fluorescent tube. Replacing it is a little easier than incandescent lamps, since in the base area it has a choke location block, which helps to change a burnt-out lamp with ease of grip.

Replacing lamps in built-in luminaires

More knowledge on how to change light bulbs is required when replacing them in built-in (spot) lamps. Here you need to take into account the type of base. It can be threaded with different diameters. Pin type with varying numbers of pins is also popular. The lamp can be either LED, halogen or fluorescent. Required electric power for them it is also different, 12V or 220V. You need to select an identical light bulb either from the packaging of the burnt one (where the marking is indicated) or from a sample.

Built-in lamps are mounted in the ceiling using double-spring struts. The lamp must be taken by the edges and slowly pulled down. Sometimes you don’t have to pull it out completely; a certain length is enough to unscrew a lamp with a screw base. If the lamp is completely removed, then after screwing in a new light bulb, you need to compress the springs to the base and insert it into the mounting hole, slowly insert the lamp into the ceiling.

The pin bulb is secured in the luminaire with a locking ring. It must be squeezed with your fingers and pulled out. The light bulb will hang on the wires. Disconnect the lamp from the terminal. Connect the new one and recess it into the lampshade, securing it with a retaining ring.

Do you know how to change a built-in light bulb?

Built-in lamps are often and widely used in the construction of suspended ceilings.

Many owners do the installation of the structure themselves, thereby gaining additional knowledge and saving on installation work.

But most people order ceiling installation from a specialized company, not caring that later they will have to decide some issues themselves.

So, if you don’t know how to change a light bulb in a suspended ceiling, then this article is for you.

Lamps used

Several types of lamps are used in luminaires that are installed on suspended ceilings. Let's look at some of these lamps below.

1. Halogen lamps

They can be installed with a minimum gap between the installed ceiling and its base. These lamps produce strong and bright illumination.

halogen lamps in the interior

The disadvantage of using halogen lamps in a suspended ceiling is that replacing this element is more difficult than, for example, an incandescent lamp. At the same time, you need to be very careful.

From correct installation halogen lamp depends on its service life.

2. Incandescent lamps

mirror incandescent lamps

As you know, frequent changes in lighting negatively affect the operation of incandescent light bulbs. Best used to prevent possible problems There are voltage stabilizers on the branch.

Incandescent lamps are much easier to replace than other types of lamps. suspended ceiling, because they are well known to many.

3. LED lamps

This type of lamps is the most economical and durable. Another advantage is that LED lamps are compact and are used in various design applications.

Design ceiling lamps All types are approximately the same and consist of:

Lamp housing containing wires and socket
Clamps that secure the device
Protective glass or plastic cover
Fixing ring

dimensions of the built-in lamp

Progress of lamp replacement: stages of work

First of all, the most important thing. The power supply must be turned off. Don't forget about safety precautions.
After this, choose a stable and reliable stand or ladder so that you can do the work comfortably. Work in tension and suspension systems requires special care to eliminate the possibility of damage to the tension fabric of the ceiling. Moreover, if the ceiling is a mirror system, any careless movement can cause irreparable harm.
Unlock the light bulb in the housing; a special locking ring is provided for this.

When performing this step, hold the light bulb firmly; the ring itself is usually spring-loaded and can easily slip out of your hand.
Next, you need to remove the lamp itself in the manner provided for its fastening. After making sure that the new lamp is the same power as the previous one, you can change the built-in light bulb. Don't forget to put the ring back in place and secure it.

Types of lamp mounting

At self-replacement lamps, you need to know the design of the lamp mount itself. There are 3 types of fastening:

With traditional right-hand thread
Fastening with pins
Swivel mount

So, with the first type of fastening everything is simple; this type is used for a regular, well-known cartridge.
There are lamps that are mounted using special pins that serve as guides. Such pins are fixed after characteristic click .

It is important to know that when replacing this type of fastener, do not press with force. It will click effortlessly if you hit the groove correctly.

Third type of fastening consists of 2 stages: First you need to insert the lamp, and then turn it 90 degrees to fix the element.

Before replacing any of the above lamps, inspect it carefully. If you change energy saving lamp or incandescent, then you need to turn it counterclockwise, but do not press.

how to change a light bulb - photo instructions

If you saw the coating and another cone inside the lamp, then you are holding a halogen element in your hands. It is attached to pins and there is no need to twist anything.

http://potolkipro.com