Adaptive station aqua robot jet 80 s. Aquarobot of the jet l series is universal. Aquarobot station ensures reliable shutdown

Universal automatic pumping station Unipump station Aquarobot JET 80 L-24- intended for serving clean cold water, which does not contain abrasive particles and long-fiber inclusions, from shallow wells and boreholes, storage tanks and other sources of water supply in automatic mode(turning on and off as the consumer consumes water), as well as to increase the pressure in the main water supply
Application area pumping station Unipump Aquarobot JET 80 L-24- for autonomous water supply of small buildings, irrigation systems for vegetable gardens, garden plots, small farms, increasing pressure in the water supply network. The stations are equipped electronic device, which turns off the pump in the absence of water flow, which protects the pump from operating in “dry running” mode and from improper installation of equipment and the water supply line.
The content of mechanical impurities in water is no more than 100 g/m3, the size of impurities is no more than 1 mm. The temperature of the pumped water is no more than +35°C.
Water supply station Unipump Aquarobot JET 80 L-24 capable of sucking water from a depth of up to 8 m.
Operating principle of Aquarobot
The pumping station consists of a 24-liter hydraulic accumulator, a PM5-3W device (connecting a PM-5 pressure switch, a five-pin fitting and a pressure gauge) and an AQUAROBOT TURBI device equipped with a flow sensor installed on the pump discharge pipe. The pressure switch controls turning the pump on and off.
The switch-on pressure is adjustable from 1 - 2.5 bar, the switch-off pressure is 1.8 - 4.5 bar. Factory settings are 1.5 and 3.0 bar, respectively. Electronic-mechanical flow sensor with a microprocessor has increased sensitivity - 2 l/min and provides reliable shutdown station in case of failure of the pressure switch, as well as in cases where the pump cannot dial operating pressure.
Pumping station Unipump Aquarobot JET 80 L-24 ensures reliable shutdown of the station

in low well productivity mode (“dry run”);
in the mode of dynamic fluctuations of the water level in the well below 8 meters;
in case of improper installation of equipment and water supply lines;
in case of jamming of the pump impeller.

Features of the home water supply station Unipump Aquarobot JET 80 L-24:

Automatically turns off when there is no water in the water supply system;
Automatically switches off when the pump impeller becomes jammed;
Works stably when the mains voltage drops to 120 V;
Operates stably at a critical suction depth of 8 meters and below, in dynamic mode;
Adaptively maintains pressure in the water supply system;
Automatically turns off if the station is incorrectly connected to the water supply source;
Possibility of adjusting the upper and lower pressure threshold.

Adaptive pumping station AQUAROBOT JET 80 S 2 liters - with hydraulic accumulator 2 liters designed for feeding clean water, which does not contain abrasive particles and fibrous inclusions, from shallow wells, wells and other sources of water supply in automatic mode (turning on and off as the consumer consumes water). The stations are equipped electronic unit, which controls the operation of the pump in terms of flow and minimum pressure (Pmin), and also protects the pump from operation in the “dry running” mode and other emergency situations(drop in mains voltage, incorrect installation, etc.).

Advantages of automatic adaptive station AQUAROBOT JET 80 S 2 liters

Automatically turns off when there is no water in the water supply system.
Automatically switches off when the pump impeller becomes jammed.
Operates stably when the mains voltage drops to 120 V.
Automatically turns off if there is no air pressure in the accumulator.
Automatically turns off when water leaks from the water supply system, if the flow rate is no more than 2 l/min.
Adaptively maintains pressure in the water supply system, which significantly increases the service life of the pump.
Operates stably at a critical suction depth of 8 meters.
It automatically turns off if the station is incorrectly connected to the water supply source (for stable operation at low voltage or a critical suction depth of 8 meters, the water flow rate must be more than 2 l/min).

The principle of operation of the station is that when a water flow passes through the control unit at a speed above 2 l/min, or when the pressure drops below Pmin (1.5±0.3 bar), the pump turns on and pumps water continuously, creating pressure, the value of which depends on the pump parameters. When the water flow stops or its speed decreases to 2 l/min, the pump automatically turns off with a thirty-second delay.

AQUAROBOT JET 80 S 2 liters ensures reliable shutdown of the station

In low well productivity mode (“dry run”)
If there is no air in the accumulator (no pressure)
When the water flow is below 2 liters per minute (line leakage)
In the mode of dynamic fluctuation of the water level in the well below 8 meters
In case of improper installation of equipment and water supply lines

In the event of an emergency shutdown of the pumping station, it is necessary to eliminate the cause and restart it.

Attention. The use of the station in pressure boosting systems is not allowed if the pressure created by the pump, combined with the main pressure, is higher than or close to 6 bar.

Technical information

Options electrical network– ~220 V ± 10%, 50 Hz
Suction height – 8 m (for AQUAROBOT JET, JS) / 5 m (for AQUAROBOT QB)
Operating water temperature range – +1 … +35°С, at temperature environment+1 … +40°С and air humidity no more than 70%.
Connecting dimensions: 1″ external thread x 1″ internal thread
Pressure compressed air in the hydraulic accumulator – 0.15 MPa (1.5 bar)
Maximum permissible pressure in the system – 6 bar
Pump activation pressure Pmin – 1.5±0.3 bar
The minimum sensitivity of the flow sensor is 2 l/min.

Technical information

Pressure and flow characteristics

Model	P, (kW)	Performance
		Q, l/min	0	10	20	30	40	50	60	70
		Q, m 3 /hour	0	0,6	1,2	1,8	2,4	3,0	3,6	4,2
AQUAROBOT JET 40 S	0.37	Pressure, N(m)	30	20	11	9.5	–	–	–	–
AQUAROBOT JET 60 S	0.45		30	29	20	11	–	–	–	–
AQUAROBOT JET 80 S	0.6		38	32	25	18	10	2	–	–
AQUAROBOT JET 100 S	0.75		43	38	32	25	18	10	2	–

* - the given data on maximum pressure and productivity are valid at zero suction depth and an electrical network voltage of 220V±10%.

Contents of delivery:

Automatic water supply station assembly – 1 pc.
Operating manual – 1 pc.
Packaging – 1 pc.

Order and buy Adaptive pumping station AQUAROBOT JET 80 S 2 l. By attractive price with delivery throughout Moscow, Moscow region and Russian Federation. Adaptive pumping station AQUAROBOT JET 80 S 2 l. prices, specifications, photographs and related products. AQUAROBOT pumping stations with a 2 liter hydraulic accumulator are available and can be ordered from Gidkomfort.

Universal automatic pumping stations AQUAROBOT JET L series— designed for supplying clean cold water that does not contain abrasive particles and long-fiber inclusions from shallow wells and boreholes, storage tanks and other water supply sources in automatic mode (turning on and off as the consumer consumes water), as well as to increase pressure in the main water supply .

Advantages of the universal automatic station AQUAROBOT

Automatically turns off when there is no water in the water supply system;
Automatically switches off when the pump impeller becomes jammed;
Works stably when the mains voltage drops to 120 V;
Operates stably at a critical suction depth of 8 meters and below, in dynamic mode;
Adaptively maintains pressure in the water supply system;
Automatically turns off if the station is incorrectly connected to the water supply source;
Possibility of adjusting the upper and lower pressure threshold.

Application area

For autonomous water supply of small buildings, irrigation systems for vegetable gardens, garden plots, small farms, increasing pressure in the water supply network. The stations are equipped with an electronic device that turns off the pump in the absence of water flow, which protects the pump from operating in the "" mode. dry running" and from improper installation of equipment and water mains.

AQUAROBOT pumping stations of the JET L series are capable of sucking water from a depth of up to 8 m. AQUAROBOT JET L stations are assembled on the basis surface self-priming pumps of the JET L series (trademark UNIPUMP). They have a hydraulic accumulator with a volume of 24 liters.

Principle of operation

The pumping station consists of a 24-liter hydraulic accumulator, a PM5-3W device (connecting a PM-5 pressure switch, a five-pin fitting and a pressure gauge) and an AQUAROBOT TURBI device equipped with a flow sensor installed on the pump discharge pipe. The pressure switch controls turning the pump on and off.

The switch-on pressure is adjustable from 1 - 2.5 bar, the switch-off pressure is 1.8 - 4.5 bar. Factory settings are 1.5 and 3.0 bar, respectively. The electronic-mechanical flow sensor with a microprocessor (developed by SABLINE SERVICE LLC) has increased sensitivity - 2 l/min and ensures reliable shutdown of the station in the event of a failure of the pressure switch, as well as in cases where the pump cannot reach operating pressure.

AQUAROBOT station ensures reliable shutdown

in low well productivity mode (“dry run”);
in the mode of dynamic fluctuations of the water level in the well below 8 meters;
in case of improper installation of equipment and water supply lines;
in case of jamming of the pump impeller.

APPLICATION AREA
Automatic water supply station AQUAROBOT JET 80 L-5 based on a centrifugal electric pump and hydraulic accumulator, designed to pump clean cold fresh water from wells, boreholes, open reservoirs, etc. with a water depth of no more than 7 m. For use in individual water supply systems. The automatic pumping station turns on and off automatically, in addition, it maintains the water supply system under pressure. An automatic water supply station can be used to increase pressure in the presence of a main water supply with insufficient pressure. The presence of a dry running sensor ensures that the pump operates in automatic mode and is protected from operation without water.
OPERATING LIMITATIONS:

The maximum temperature of pumped water is + 35C;
The maximum number of starts is no more than 30 per hour;
The maximum linear size of solid particles in pumped water is no more than 0.1 mm;
The maximum permissible viscosity of pumped water is the viscosity of pure water +5%
Maximum head: 38 m
Maximum flow: 50 l/min
Max. consumption power – 600W
Thread size for pipeline connection 1”
The volume of the hydraulic accumulator is 5 l.

DESIGN FEATURES:

Pump electric motor - single-phase (220V/50Hz), air cooling with capacitor and built-in thermal protection relay.
Nutrition from single-phase network 220V, 50Hz
Built into the engine thermal relay overheat protection
The capacitor is located in the motor.
Impeller material: plastic,
Accumulator material: painted metal
Pump shaft: stainless steel
Pump body: cast iron
Protection against working without water – yes.

Technical characteristics of the product and photos may differ from those indicated on the website, please check specifications goods at the time of purchase and payment. All information on the website about products is for reference only.

Payment for goods

Payment by bank card- payment for goods by bank card is carried out ONLY at the pick-up point.

Cash payment - payment for goods is made in cash to the courier. Payment is accepted in Russian rubles strictly in accordance with the price indicated on the sales receipt. When picking up goods at your own expense, a 3% discount is provided.

Cashless payment - payment for goods by bank transfer is possible by all legal and individuals. After receiving your order, you will be sent an invoice by e-mail or by fax. Please note that our company is NOT a VAT payer.

Delivery of goods

Delivery of goods within the Moscow Ring Road - 450 rubles.

Delivery of goods outside the Moscow Ring Road - 450 rubles + 30 rubles per kilometer. Delivery of goods to the regions - 450 rubles + tariff transport company(you pay when receiving the goods in your city.

RUB 8,575

Universal automatic pumping stations AQUAROBOT JET L series- designed for supplying clean cold water that does not contain abrasive particles and long-fiber inclusions from shallow wells and boreholes, storage tanks and other water supply sources in automatic mode (turning on and off as the consumer consumes water), as well as to increase pressure in the main water supply .

Advantages of universal automatic station AQUAROBOT

Automatically turns off when there is no water in the water supply system;
Automatically switches off when the pump impeller becomes jammed;
Operates stably when the mains voltage drops to 170 V;
Operates stably at a critical suction depth of 8 meters and below, in dynamic mode;
Adaptively maintains pressure in the water supply system;
Automatically turns off if the station is incorrectly connected to the water supply source;
Possibility of adjusting the upper and lower pressure threshold.

Application area

AQUAROBOT pumping stations of the JET L series are capable of sucking water from a depth of up to 8 m. AQUAROBOT JET L stations are assembled on the basis surface self-priming pumps of the JET L series(trademark UNIPUMP). They have a hydraulic accumulator with a volume of 24 liters.

Principle of operation

The switch-on pressure is adjustable from 1 - 2.5 bar, the switch-off pressure is 1.8 - 4.5 bar. Factory settings are 1.5 and 3.0 bar, respectively. The electronic-mechanical flow sensor with a microprocessor (developed by UNIPUMP) has increased sensitivity - 2 l/min and ensures reliable shutdown of the station in the event of a failure of the pressure switch, as well as in cases where the pump cannot gain operating pressure.

AQUAROBOT ensures reliable shutdown of the station

in low well productivity mode (“dry run”);
in the mode of dynamic fluctuations of the water level in the well below 8 meters;
in case of improper installation of equipment and water supply lines;
in case of jamming of the pump impeller.

Technical information

Pressure and flow characteristics

Model	P, (kW)	Performance
		Q, l/min	0	10	20	30	40	50	60	70
		Q, m 3 /hour	0	0,6	1,2	1,8	2,4	3,0	3,6	4,2
AQUAROBOT JET 80L	0.6	Pressure, N(m)	38	32	25	18	10	2	-	-
AQUAROBOT JET 100L	0.75		43	38	32	25	18	10	2	-
AQUAROBOT JET 110L	0.9		53	48	40	32	18	10	-	-

* - the given data on maximum pressure and productivity are valid at zero suction depth and an electrical network voltage of 220V±10%.

Pumping station	Hydraulic tank volume	dimensions			A	M	B	C	D	DNA	DNM	Box dimensions			Net weight
	Hydraulic tank volume	L	W	H	A	M	B	C	D	DNA	DNM	a	b	h	Net weight
	l	mm								"		mm			kg
JET 80L	24	485	275	585	445	530	265	134	217	1	1	510	310	640	19,1
JET 100L		485													19,3
JET 110L		500													21,05