Pumping station Aquarobot qb 60. Aquarobot qb is an inexpensive automatic station with dry-running protection. Advantages of the Unipump pumping station Aquarobot QB
Application area pumping station Unipump Aquarobot QB 60- for autonomous water supply of small buildings, irrigation systems for vegetable gardens, garden plots, small farms, increasing pressure in the water supply network. The stations are equipped electronic device, which turns off the pump in the absence of water flow, which protects the pump from operating in “dry running” mode and from improper installation of equipment and the water supply line.
The content of mechanical impurities in water is no more than 100 g/m3, the size of impurities is no more than 1 mm. The temperature of the pumped water is no more than +35°C.
Water supply station Unipump Aquarobot QB 60 capable of sucking water from a depth of up to 5 m.
Operating principle of Aquarobot
Pumping station consists of a 2-liter hydraulic accumulator, a PM5-3W device (connecting a PM-5 pressure switch, a five-pin fitting and a pressure gauge) and an AQUAROBOT TURBI device equipped with a flow sensor installed on the pump discharge pipe. The pressure switch controls turning the pump on and off.
The switch-on pressure is adjustable from 1 - 2.5 bar, the switch-off pressure is 1.8 - 4.5 bar. Factory settings are 1.5 and 3.0 bar, respectively. Electronic-mechanical flow sensor with a microprocessor has increased sensitivity - 2 l/min and provides reliable shutdown station in case of failure of the pressure switch, as well as in cases where the pump cannot gain operating pressure.
Unipump pumping station Aquarobot QB 60 ensures reliable shutdown of the station
- in low well productivity mode (“dry run”);
- in the mode of dynamic fluctuations of the water level in the well below 8 meters;
- in case of improper installation of equipment and water supply lines;
- in case of jamming of the pump impeller.
- Automatically turns off when there is no water in the water supply system;
- Automatically switches off when the pump impeller becomes jammed;
- Works stably when the mains voltage drops to 120 V;
- Operates stably at a critical suction depth of 8 meters and below, in dynamic mode;
- Adaptively maintains pressure in the water supply system;
- Automatically turns off if the station is incorrectly connected to the water supply source;
- Possibility of adjusting the upper and lower pressure threshold.
Adaptive automatic pumping station AQUAROBOT QB series- with a 2 or 5 l hydraulic accumulator designed to supply clean water, which does not contain abrasive particles and fibrous inclusions, from shallow wells, wells and other sources of water supply in automatic mode (turning on and off as the consumer consumes water). The stations are equipped electronic unit, which controls the operation of the pump in terms of flow and minimum pressure (Pmin), and also protects the pump from operation in “dry running” mode and other emergency situations (drop in mains voltage, incorrect installation, etc.).
Advantages of automatic adaptive station AQUAROBOT
- Automatically turns off when there is no water in the water supply system.
- Automatically switches off when the pump impeller becomes jammed.
- Operates stably when the mains voltage drops to 170 V.
- Automatically turns off if there is no air pressure in the accumulator.
- Automatically turns off when water leaks from the water supply system, if the flow rate is no more than 2 l/min.
- Adaptively maintains pressure in the water supply system, which significantly increases the service life of the pump.
- Operates stably at a critical suction depth of 8 meters.
- It automatically turns off if the station is incorrectly connected to the water supply source (for stable operation at low voltage or a critical suction depth of 8 meters, the water flow rate must be more than 2 l/min).
The principle of operation of the station is that when a water flow passes through the control unit at a speed above 2 l/min, or when the pressure drops below Pmin (1.5±0.3 bar), the pump turns on and pumps water continuously, creating pressure, the value of which depends on the pump parameters. When the water flow stops or its speed decreases to 2 l/min, the pump automatically turns off with a thirty-second delay.
AQUAROBOT ensures reliable shutdown of the station
- In low well productivity mode (“dry run”)
- If there is no air in the accumulator (no pressure)
- When the water flow is below 2 liters per minute (line leakage)
- In the mode of dynamic fluctuation of the water level in the well below 8 meters
- In case of improper installation of equipment and water supply lines
In the event of an emergency shutdown of the pumping station, it is necessary to eliminate the cause and restart it.
Attention. The use of the station in pressure boosting systems is not allowed if the pressure created by the pump, combined with the main pressure, is higher than or close to 6 bar.
Technical information
- Options electrical network– ~220 V ± 10%, 50 Hz
- Suction height – 8 m (for AQUAROBOT JET, JS) / 5 m (for AQUAROBOT QB)
- Operating water temperature range – +1 ... +35°С, at temperature environment+1 ... +40°С and air humidity no more than 70%.
- Connecting dimensions: 1" external thread x 1" internal thread
- Pressure compressed air in the hydraulic accumulator – 0.15 MPa (1.5 bar)
- Maximum permissible pressure in the system – 6 bar
- Pump activation pressure Pmin – 1.5±0.3 bar
- The minimum sensitivity of the flow sensor is 2 l/min.
Pressure and flow characteristics
| Pumping station | Hydraulic tank volume | dimensions | A | M | C | D | E | DNA | DNM | Box dimensions | Net weight) | ||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| L | W | H | a | b | h | ||||||||||
| l | mm | " | mm | kg | |||||||||||
| QB 60 | 2 | 375 | 137 | 305 | 65 | 235 | 104 | 105 | 84 | 1 | 1 | 470 | 240 | 390 | 7,5 |
| QB 70 | 410 | 140 | 320 | 70 | 250 | 110 | 120 | 88 | 10,0 | ||||||
| QB 80 | 11,0 | ||||||||||||||
Equipment in the online store
 |
The adaptive automatic pumping station Unipump Aquarobot of the QB series is designed to supply clean water that does not contain abrasive particles and fibrous inclusions from shallow wells, wells and other water supply sources in automatic mode (turning on and off as the consumer consumes water). The station is equipped with an electronic unit that controls the operation of the pump in terms of flow and minimum pressure (Pmin), and also protects the pump from operation in “dry running” mode and other emergency situations (drop in mains voltage, incorrect installation, etc.). The pumping station is used for automatic water supply of houses, cottages and summer cottages, organization of irrigation systems, and increasing pressure in the water supply network.
The Unipump Aquarobot QB station is assembled on the basis surface pump QB series with cast iron body. Brass impeller ensures long and reliable operation for many years.
Principle of operation Unipump stations Aquarobot QB is that when a water flow passes through the control unit at a speed above 2 l/min, or when the pressure drops below Pmin (1.5±0.3 bar), the pump turns on and pumps water continuously, creating pressure in the system , the value of which depends on the pump parameters. When the water flow stops or its speed decreases to 2 l/min, the pump automatically turns off with a thirty-second delay.
The Aquarobot pumping station adapts to the conditions of a specific water supply system and creates comfortable conditions water use for you and your household appliances. Whenever technical problems The aqua robot will simply turn off until it is eliminated technical faults in your highway.
Advantages of the Unipump Aquarobot QB pumping station:
Automatically turns off when there is no water in the water supply system.
Automatically switches off when the pump impeller becomes jammed.
Operates stably when the mains voltage drops to 120 V.
Automatically turns off if there is no air pressure in the accumulator.
Automatically turns off when water leaks from the water supply system, if the flow rate is no more than 2 l/min.
Adaptively maintains pressure in the water supply system, which significantly increases the service life of the pump.
Operates stably at a critical suction depth of 8 meters.
Automatically turns off if the station is incorrectly connected to the water supply source.
Today, owners of private houses in our country, accustomed to the dominance of European and American manufacturers in the market pumping equipment, increasingly abandoning stares for domestic brands.
One of them - trademark AquaRobot – in Lately arouses keen interest among the knowledgeable public.
We decided to get to know the products of this manufacturer better, and at the same time tell our readers about their features.
AquaRobot pumping stations (PS) are an inexpensive and high-quality solution for those who intend to organize an autonomous water supply network in a house or on a site outside the city limits.
Each model is supplied fully equipped, so To get started, the owner only needs to connect it to the water supply network and a source of electricity.
This completely ends the user’s participation; the AquaRobot NS performs all its functions automatically, while maintaining optimal parameters in the water supply system.
A feature of AquaRobot pumping stations is a well-thought-out comprehensive safety system that takes into account any emergency situations, which can only happen:
- turning off the pump if there is no water in the suction line (dry running of the pump);
- turning off the pump if the impeller is blocked or jammed;
- turning off the pump if there is no air pressure in the storage tank;
- the station recognizes the presence of leaks in the water supply network and in this case does not pump water;
- the station adapts to the parameters of the water supply network and, in case of technical problems, responds by lowering the pressure or completely turning off the pump;
- equipment is blocked in case of incorrect connection to the pressure or suction lines.
Unlike imported pumping stations, which are very picky about the quality of power supply, NS AquaRobot easily tolerate significant voltage drops even up to 120 V.
Seasonal summer residents will appreciate the mobility of the AquaRobot NS, which, due to its light weight, can be easily and quickly dismantled when cold weather arrives.
Operating principle^
Under the AquaRobot brand, two types of pumping stations are produced, which are positioned by the manufacturer as universal and adaptive.
Universal NS^
The device that controls the operation of the pump in this system is a pressure switch.
It starts the pump drive when the pressure in the network drops, which occurs while using the water supply, and turns it off as soon as the pressure returns to its previous value.
At factory settings the threshold for switching on and off corresponds to pressure values of 1.5 and 3 atm, respectively, however, the user can reconfigure the relay at his discretion.
The switch-on threshold is adjustable from 1 to 2 atm, the switch-off threshold is adjustable from 1.8 to 4 atm.
All models of universal stations equipped with a membrane hydraulic accumulator with a capacity of 24 liters.
Pumping stations with a capacious hydraulic accumulator and controllable the best way Suitable for domestic needs where water is consumed over short periods of time.
In addition to the pressure switch, you will also need one; it is designed to maintain a constant pressure level, eliminating water leakage from the system and possible pump stoppage.
Adaptive NS^
In these station models, the pump is turned on by a signal from the flow sensor. In addition, the pump motor will start when the pressure in the water supply drops below 1.53 atm.
Adaptive hydraulic pumps AquaRobot are equipped with small-volume hydraulic accumulators (2 and 5 l), which are necessary to start the pump and smooth out the resulting water hammer.
Low-pressure systems controlled by flow sensors perform best in applications where water is primarily used over long periods of time, such as for irrigation or filling a swimming pool.
With such a consumption pattern, the pump operates stably, and does not “twitch”, turning on and off, which would be observed when increasing the power of the station and equipping it with a pressure switch.
In this case, there is no need to use a large-capacity storage tank, which is designed to compensate for water consumption during short-term use of the water supply.
Selection of pumping station ^
The AquaRobot automatic pumping station is selected according to the following parameters:
- suction depth;
- pressure;
- performance.
The maximum suction depth for various models of NS AquaRobot is 5 and 8 m.
When choosing a station based on this parameter, you should take into account that the water level will drop slightly during pump operation, so you need to provide a small reserve.
The pressure and productivity of the station are interdependent quantities. In addition to their maximum values, the passport for the pumping station contains tables or graphs called the main characteristic of the pump.
They show what performance the station pump will have at a given pressure. Essentially, pressure is the pressure that the pump has to develop in order to provide the required water supply parameters.
To calculate it, add up the required pressure at the farthest point of consumption ( the optimal value is usually 2 atm or 20 meters of water column), the height of the maximum point of the network relative to the pump and the pressure loss due to hydraulic resistance in the pipeline.
The last component is calculated using a rather complex method, but it can be replaced with approximate empirical data: every 10 m of pipe, the pressure drops by 0.1 atm (1 m v. Art.).
The required performance can be calculated based on the number of connected consumers and how often they will work simultaneously.
An easier way is to use experimental data as a basis.
Thus, the peak volume of water consumption for garden plot(possibly with small house) is 0.8 – 1 cu.m. m/h; for a cottage (standard project) with a resident family of 4 – 6 people – 1.5 – 2 cubic meters. m/h; for a solid mansion with a swimming pool or fountains - 4 cubic meters. m/h or more.
Now we need to choose a station model, in the main characteristic of which the pressure we have calculated will correspond to the productivity we need.
If you are just choosing a pumping station and have not decided on the manufacturer, read the article about the most important and relevant information only in our magazine!
Also, good pumps are produced by the Italian company Marina, read reviews of these devices, prices and advice on choosing, buy exactly what you need!
Most popular models ^
We have prepared a list of the most popular Aquarobot pumping stations, with optimal price-quality ratio.
AquaRobot QB 60 370 W (adaptive) ^
This model is equipped with a Unipump QB 60 centrifugal pump with a 370 W electric drive.
The pump body is made of cast iron, the impeller is made of brass, the seal is made of graphite and ceramics. Maximum pressure and productivity are 33 m and 30 l/min, respectively.
The maximum suction depth is 5 m. The station is equipped with a built-in hydraulic accumulator with a capacity of 5 liters. The station is not intended to be used to increase pressure.
Cost – 4390 rub.
AquaRobot JET 60S-24 450 W (universal) ^
This model can be used both to supply water to the water supply system and to increase pressure when connected to a centralized water supply.
The 450 W pump is capable of developing a head of 33 m, and its maximum output is 40 l/min. The maximum permissible installation height of the pump relative to the surface of the water in the source (suction depth) is 8 m.
Cost – 7060 rub.
AquaRobot JS 100-24 750 W (universal) ^
As everybody universal stations AquaRobot, this model is equipped with a pressure switch and storage tank volume 24 l.
The pump body material is stainless steel. Motor power – 750 W, maximum pressure and productivity – 40 m and 55 l/min. Suction depth – 8 m.
Price – 8022 rub.
AquaRobot JET 100L-24 750 W (universal) ^
High-performance model with maximum output of 56 l/min. The maximum pressure at the outlet pipe is 43 mv. Art. Suction depth – up to 8 m. Can be used as a pressure amplifier.
Cost – 7700 rub.
Pumping stations AquaRobot M series ^
Models in this series are equipped borehole pumps vibration type “Rucheek” with a power of 225 W. Cumulative volume membrane tank for various models it is 5 and 20 liters.
The maximum immersion depth for the pump (relative to the water surface) is 3 m. The operation of the pump is controlled by a pressure switch brand PM/5-3W from the Italian company ItalTecnica.
The cost of the model is 3960 rubles.
(1 ratings, on average: 5,00 out of 5) 
Loading...
