Polygran concrete wall blocks. Partition stones Individual decorative elements

Concrete is the most used material in modern construction. Thanks to it, you can create almost any structure with high strength and other excellent characteristics. At the same time, in Lately it is used to create various figures, but they use a composition such as a stone flower made of M300 sand concrete or other decorative elements.

Structural elements

To begin with, it is necessary to say that this material is primarily used for the manufacture of products that are used for the construction of buildings. At the same time, they have their own differences and features ().

Aerated concrete blocks

This material is created chemically by adding a small amount of aluminum powder to a solution, which leads to a reaction that forms bubbles.

It is very difficult to make a stone from such concrete with your own hands, since it may require appropriate equipment, which is quite expensive.
It is worth noting that products made from aerated concrete have relatively good thermal conductivity and excellent strength. However, they do not tolerate direct contact with water very well, although they can allow air to pass through.

Advice! Such materials are used in the construction of buildings to create load-bearing walls. In this case, the structure can be higher than two floors.

Foam concrete

Making such a stone is quite simple.

It is enough to add a special foaming agent to the sand-cement mortar, which will create the necessary structure.

It is worth noting that such products do not have high strength, which means that their installation does not require cutting reinforced concrete with diamond wheels. However, this also does not allow the creation of structures exceeding two floors in height.
Special attention is paid to the fact that such a stone does not allow moisture to pass through, but it retains heat a little worse, unlike aerated concrete. At the same time, it creates very good sound insulation, which, combined with its low weight, is excellent for manufacturing interior partitions.

Advice! Such products are very popular due to their qualities and relatively low cost. However, to build from them, it is necessary to create a special design that accurately distributes all the loads.

Expanded clay concrete

The production of such products comes down to casting into a mold. cement mortar with the addition of expanded clay.

This requires compaction using various vibrating devices.

Ordinary expanded clay concrete stone has amazing thermal conductivity, and correct production very stable in humid environments. However, the cost of such products is quite high, and the characteristics final result not very different from other types of less expensive products.
Some craftsmen prefer to use such material to create ground floors or other structures that need protection from cold and moisture.

Advice! This type of stone is great for creating baths or saunas. However, it requires additional waterproofing.

Partition stone

This material is concrete product in the form of stone or brick, a certain shape with a cavity inside. The most a shining example One such product is PC 160. At the same time, these products are simply ideal for creating partitions, since they have excellent strength and sound insulation.

It is worth noting that such stones can have the most different design and dimensions, including the shape with the number of holes. Therefore, when making a choice, it is worth studying in detail the entire range of these products.

Advice! Each specific product can different types has its own specific characteristics. However, they are all great for creating any interior partitions.

cinder block stones

Usually reinforced concrete and stone structures They are highly durable and have a number of advantages. However, when it comes to talking about cinder block, all that can be said about it is that its cost is the most moderate and fully justifies such products.

Considering the low performance against various types of impacts, and especially loads, professional craftsmen recommend using these products to create fences or outbuildings with small dimensions. Moreover, even during installation, some units of such material can disintegrate right in your hands.

Advice! When purchasing these types of products, they usually check them only visually, but always take into account the calculations required quantity make a reserve for marriage.

Decorative elements

Quite often concrete is used to create decorative ornaments, which are not only used as individual elements, but also as an individual product. It is worth saying that the price for such a product is significantly lower than for products from natural stone or ceramics.

Facing materials

Last time fake diamond Almost anyone can create something out of concrete with their own hands. It is enough just to purchase a special shape and a vibrating surface in the form of a table.

It is worth noting that various additives and even pigment are often added to such products to give them certain properties and color. Taking this into account, you can create a variety of elements that not only have original appearance, but also resemble natural materials.

Advice! The use of such products for finishing works both indoors and outdoors is a fairly practical and economically sound solution. They combine beauty, durability and low cost.

Separate decorative elements

Products such as a stone flower made of sand concrete M 300 and the like are very often used as a basis for creating decorations for building facades. At the same time, their production sometimes requires specific skills and artistic talents.

It is worth noting that almost all such structures are based on metal reinforcement. First, a frame is created from it, around which a casting is made using a pre-designed mold or formwork.

It is important to note that all such products are very durable. Therefore, when creating them, special grooves or pins for the seats are immediately installed so that during the installation process there is no need for diamond drilling holes in concrete.

Advice! Almost all individually designed concrete products are very expensive and can be equated to real works of art. That is why their cost is quite high, which is also reflected in installation.

Conclusion

By watching the video in this article, you can familiarize yourself in detail with products of this type. At the same time, paying attention to the article presented above, it is worth concluding that popular materials modern construction, at almost all stages of building construction.

We understand how important it is to live in silence: not to hear neighbors or street noise, to sleep peacefully when there is a holiday outside the window. Therefore, the Melikonpolar company has developed special stones for the construction of quiet interior and apartment partitions. When developing the design of stones, we were guided not only by the requirements Building codes and rules for sound insulation, but also simple, everyday human needs. The stones we have developed for apartment and interior partitions meet the highest standards of quality and comfort of life:

The airborne noise insulation index of PK-160 (52 dB), SKTs 1R-1pg (54 dB) and SKTs 2R-19 (45 dB) meets the highest requirements of SNiP 23-03 “Noise Protection”;
PK-160, SKTs 1R-1pg and SKTs 2R-19 are made of concrete with strength M 200, which ensures vandal resistance of the partitions and protection from accidental damage;
The high strength of the partitions allows you to fearlessly attach any hanging structures without special fasteners;
The surface of the stones has good adhesion and is easy to plaster;
If you install the partitions yourself, you will be pleased with the light weight of the stones and the thoughtfulness of the design: the stones are laid empty down, which prevents the mortar from falling through; the vertical seam is made dry (without mortar) and has a tongue-and-groove connection system.

Inter-apartment PC-160

Concrete stone PK - 160 is intended for the construction of inter-apartment partitions in houses of all categories;
The airborne noise insulation index of PC - 160 is 52 dB with a thickness of only 16 cm, which satisfies the main requirements for inter-apartment partitions;
The thickness of the stone is 160 mm, allowing you to increase the area interior spaces(compared to thicker brick partitions);
PC - 160 has a single module with the most common thickness monolithic walls, which allows you to fill openings without creating additional protrusions on the wall;
The double tongue-and-groove system significantly increases the reliability of the vertical connection of stones, which is performed dry, without mortar, reducing the time and labor intensity of construction;
The stone is laid hollow down, the top surface is solid, which prevents the mortar from falling into the voids.

Specifications:

Dimensions, LxBxH, mm	400x160x188 mm
Product weight	19.2 kg
Volume weight	1595 kg/cub.m
Emptiness	30,6 %
Frost resistance grade	F 50
Concrete grade by strength	M 200
Water absorption by mass	3 - 5%
	52 dB
Number of pieces per sq.m	12,5

Inter-apartment SCC 1R - 1pg

SKTs 1R - 1pg is intended for the construction of inter-apartment partitions in houses of all categories;
SKTs 1R - 1pg satisfies the main requirement for inter-apartment partitions; the airborne noise insulation index when plastered on both sides is 54 dB;
The thickness of the stone is 190 mm, which allows you to increase the area of internal premises in comparison with thicker brick partitions;
The longitudinal hollowness of the stone with a central partition allows for electrical wiring separately for two rooms, without fear of damage to the electrical cable;
The high strength grade of concrete eliminates the possibility of accidental damage or breaking of the wall, for example during repairs;
The surface of the stone has good adhesion and is easy to plaster;
The stone is laid hollow down, the upper surface is solid, which prevents the mortar from falling into the voids;
SKTs 1R - 1pg is also produced with the addition of expanded clay, which can significantly reduce the weight of the product while maintaining the main technical parameters;

Specifications:

Dimensions, LxBxH, mm	390x190x188 mm
Product weight	19.9 (16.5)* kg
Volume weight	1430 (1180) kg/cub.m
Emptiness	38 %
Frost resistance grade	F 50
Concrete grade by strength	M 200 (M 150)
Water absorption by mass	3 - 5%
Airborne noise insulation index	54 (53) dB
Number of pieces per sq.m	12,8

Interior SKTs 2R - 19

SKTs 2R-19 is intended for the construction of interior partitions in houses of all categories;
The airborne noise insulation index 2R-19 is 45 dB and fully complies with the requirements of SNiP 23-03-2003 “Noise Protection”
The thickness of the stone - only 80 mm - allows you to increase the area of internal premises in comparison with thicker partitions made of brick and aerated concrete;
A convenient tongue-and-groove system for connecting stones allows vertical joints to be made dry, without mortar, which significantly reduces the time and labor intensity of construction;
The high strength grade of concrete creates a reliable wall, protected from accidental damage. You can hang any hanging furniture on such a wall without any problems;
The surface of the stone has good adhesion and is easy to plaster;
The low water absorption of the stone allows it to be used in rooms with humid conditions;
SKTs 2R-19 is also produced with the addition of expanded clay, which can significantly reduce the weight of the product while maintaining the main technical parameters.

Specifications:

Dimensions, LxBxH, mm	400x80x188 mm
Product weight	10.7 (8.8)* kg
Volume weight	1780 (1470) kg/cub.m
Emptiness	23 %
Frost resistance grade	50
Concrete grade by strength	M 200 (M 150)
Water absorption by mass	3 - 5 %
Airborne noise insulation index	45 dB
Number of pieces per sq.m	12,6

Vibro-pressed wall blocks under the polygran brand are produced by the company Lentehstrom. The range includes wall blocks for external walls (thickness 190 and 200) and facade systems, interior (70 and 80 mm thick) and inter-apartment partition blocks(thickness 130, 160, 190), as well as ventilation blocks and concrete bricks.

All stones are produced at modern equipment POYATOS companies have high quality and precise geometry. In production, the requirements of GOST 6133-99 “Concrete wall stones” are strictly observed. Septum stones comply with the noise insulation requirements SP 51.13330.2011 “Noise Protection”, have all the necessary certificates and other documents.

From the KELLE company you can buy POLYGRAN concrete wall panels at manufacturer’s prices with delivery throughout St. Petersburg and Leningrad region. To calculate the cost of wall blocks, send a request to sale@site

Select subcategory

Default Name (A - Z) Name (Z - A) Price (low > high) Price (high > low) Rating (starting from high) Rating (starting from low) Model (A - Z) Model (Z - A)

12 25 50 75 100

Model: KPR PR-PS 50

Buy

To bookmarks
Comparing to

Partition stone Polygran KPR PR-PS 50 is produced by semi-dry vibrocompression from environmentally friendly concrete using foreign-made equipment. The blocks are highly durable and durable. Concrete partition stones are non-flammable, will not rot and provide excellent sound insulation. Noise insulation index - 43/48 dB (without plaster/with plaster).

The shape of the blocks is specially designed to facilitate the laying process. At the ends there are protrusions of the tongue-and-groove system, and special voids are provided in the body of the block, making it easy to split them when laying in a running pattern.

The name KPR PR-PS 50 stands for “ordinary ordinal hollow partition stone.” Another spelling option is KPR-PR-PS-50*8*19-75-1450 (TU 5741-001-96168269-2007).

Partition stones KPR PR-PS 50 are used for laying walls in bathrooms, as well as for constructing interior partitions. The stones are suitable for rooms with dry, normal and humidity conditions according to SNiP 11-3-79.

KPR PR-PS 50 stones are sold in multiples of pallets with delivery by manipulator or on-board truck. To clarify the cost, send inquiries to the sales department of KELLE LLC by mail.

Buy

To bookmarks Comparing to

Buy

To bookmarks Comparing to

PARTITION STONE KPR PR-PS 50

Model: KPR PR-PS 50

Buy

To bookmarks
Comparing to

The name KPR PR-PS 50 stands for “ordinary ordinal hollow partition stone.” Another spelling option is KPR-PR-PS-50*8*19-75-1450 (TU 5741-001-96168269-2007).

KPR PR-PS 50 stones are sold in multiples of pallets with delivery by manipulator or on-board truck. To clarify the cost, send inquiries to the sales department of KELLE LLC by mail.

The name KPR PR-PS 50 stands for “ordinary ordinal hollow partition stone.” Another spelling option is KPR-PR-PS-50*8*19-75-1450 (TU 5741-001-96168269-2007).

KPR PR-PS 50 stones are sold in multiples of pallets with delivery by manipulator or on-board truck. To clarify the cost, send inquiries to the sales department of KELLE LLC by mail.

Buy

To bookmarks Comparing to

Buy

To bookmarks Comparing to

Model: KPR PR-PS KB 50

Buy

To bookmarks
Comparing to

Partition stone Polygran KPR PR-PS KB 50 is produced by semi-dry vibrocompression from environmentally friendly expanded clay concrete using foreign-made equipment. The blocks are highly durable and durable. Concrete partition stones are non-flammable, will not rot and provide excellent sound insulation. Noise insulation index - 44/47 dB (without plaster/with plaster).

The name KPR PR-PS KB 50 stands for “ordinary ordinal hollow partition stone expanded clay concrete." Another spelling option is KPR-PR-PS-KB-50*8*19-75-1450 (TU 5741-001-96168269-2007).

Partition stones KPR PR-PS KB 50 are used for laying walls in bathrooms, as well as for constructing interior partitions. The stones are suitable for rooms with dry, normal and humidity conditions in accordance with SNiP 11-3-79.

KPR PR-PS KB 50 stones are sold in multiples of pallets with delivery by manipulator or on-board truck. To clarify the cost, send inquiries to the sales department of KELLE LLC by mail.

Buy

To bookmarks Comparing to

Buy

To bookmarks Comparing to

PARTITION STONE KPR PR-PS KB 50

Model: KPR PR-PS KB 50

Buy

To bookmarks
Comparing to

The name KPR PR-PS KB 50 stands for “ordinary ordinal hollow partition stone expanded clay concrete." Another spelling option is KPR-PR-PS-KB-50*8*19-75-1450 (TU 5741-001-96168269-2007).

KPR PR-PS KB 50 stones are sold in multiples of pallets with delivery by manipulator or on-board truck. To clarify the cost, send inquiries to the sales department of KELLE LLC by mail.

The name KPR PR-PS KB 50 stands for “ordinary ordinal hollow partition stone expanded clay concrete." Another spelling option is KPR-PR-PS-KB-50*8*19-75-1450 (TU 5741-001-96168269-2007).

KPR PR-PS KB 50 stones are sold in multiples of pallets with delivery by manipulator or on-board truck. To clarify the cost, send inquiries to the sales department of KELLE LLC by mail.

Buy

To bookmarks Comparing to

Buy

To bookmarks Comparing to

Buy

To bookmarks
Comparing to

Concrete wall stone Polygran 80 PG is designed specifically for the installation of interior partitions. The stone provides sound insulation of 45 dB without application and 47 dB with plaster. The stones are suitable for wet areas and do not require additional hydrophobization. The following markings for these blocks are also found: KPR-PR-PS-50x18.8x8-75-1650 GOST 6133-99. Wall blocks Polygran 80 PG are non-flammable (flammability K0), fire resistance limit REI 150.

If you want to buy Polygran wall blocks, send a request to the sales department by email indicating the address construction site. Blocks are sold with delivery by on-board truck or manipulator, in multiples of a pallet. There are 120 blocks on one pallet.

Buy

To bookmarks Comparing to

Buy

To bookmarks Comparing to

STONE FOR INTERIOR WALLS POLYGRAN 80 PG

Model: KPR-PR-PS-50x18.8x8-75-1650

Buy

To bookmarks
Comparing to

Concrete wall stone Polygran 80 PG is designed specifically for the installation of interior partitions. The stone provides sound insulation of 45 dB without application and 47 dB with plaster. The stones are suitable for wet rooms and do not require additional hydrophobization. The following markings for these blocks are also found: KPR-PR-PS-50x18.8x8-75-1650 GOST 6133-99. Wall blocks Polygran 80 PG are non-flammable (flammability K0), fire resistance limit REI 150.

If you want to buy Polygran wall blocks, send a request to the sales department by email indicating the address of the construction site. Blocks are sold with delivery by on-board truck or manipulator, in multiples of a pallet. There are 120 blocks on one pallet.

Concrete wall stone Polygran 80 PG is designed specifically for the installation of interior partitions. The stone provides sound insulation of 45 dB without application and 47 dB with plaster. The stones are suitable for wet rooms and do not require additional hydrophobization. The following markings for these blocks are also found: KPR-PR-PS-50x18.8x8-75-1650 GOST 6133-99. Wall blocks Polygran 80 PG are non-flammable (flammability K0), fire resistance limit REI 150.

Buy

To bookmarks Comparing to

Buy

To bookmarks Comparing to

Buy

To bookmarks
Comparing to

Concrete wall stone Polygran 70 PG is designed specifically for the construction of interior partitions. The stone provides sound insulation of 43 dB without application and 47 dB with plaster. The stones are suitable for wet rooms and do not require additional hydrophobization. The following markings for these blocks are also found: KPR-PR-PS-50x18.8x7-75-1940 GOST 6133-99. Wall blocks Polygran 70 PG are non-flammable (flammability K0), fire resistance limit REI 150.

Buy

To bookmarks Comparing to

Buy

To bookmarks Comparing to

STONE FOR INTERIOR WALLS POLYGRAN 70 PG

Model: KPR-PR-PS-50x18.8x7-75-1940

Buy

To bookmarks
Comparing to

Buy

To bookmarks Comparing to

Buy

To bookmarks Comparing to

STONE FOR INTERIOR WALLS POLYGRAN 80 KB PG

Model: KPR-PR-PS-50x18.8x8-75-1490

Buy

To bookmarks
Comparing to

Expanded clay concrete wall stone Polygran 80 KB PG is designed specifically for the installation of interior partitions. The stone provides sound insulation of 44 dB without application and 48 dB with plaster. The stones are suitable for wet rooms and do not require additional hydrophobization. The following markings for these blocks are also found: KPR-PR-PS-50x18.8x8-75-1490 GOST 6133-99. Wall blocks Polygran 80 KB PG are non-flammable (flammability K0), fire resistance limit REI 150. The Polygran 80 KB PG block is completely similar to the block, but is made of expanded clay concrete.