Special instant glue for porcelain and ceramics uhu porzellan keramik. How and with what to glue ceramics: types of adhesives, instructions for gluing at home and photos What kind of glue to glue ceramics with

Dear porcelain trinkets, heirloom crystal vases, earthenware jugs and painted dishes - all this sits on shelves and cabinets, becomes covered with dust, and breaks with enviable regularity. The easiest way is to sweep the fragments into a dustpan with a broom and throw them away. But there are situations when a broken item is very dear to someone in the family, or its absence in its usual place in the closet will cause an extraordinary family showdown. Then you shouldn’t panic and give in to despair, but you should carefully (so as not to get hurt) and carefully (you can’t lose anything) collect all the pieces and glue them together.

This can be done with glue prepared from homemade ingredients, or you can consult a specialist in the store and buy a special composition.

Expensive porcelain dishes and figurines

If you are “lucky” enough to break off a fragile handle from a cup of an elite service or break a collectible Meissen porcelain figurine, you will have to not only glue it, but also do restoration.

In this situation, you will need a special transparent porcelain glue or even epoxy resin. Or you can mix gypsum-based cement with egg white, and glue the pieces together very quickly. This composition dries quickly.

Another recipe, specifically for restoration, also based on egg whites. They are whipped into a very “strong” foam, kept in the refrigerator for a day and mixed with baking soda until you get a doughy paste. This “plasticine” is convenient for assembling porcelain figurines, as it can be used to fill gaps and cracks.

After drying, you will have to carefully clean the gluing areas with a sharp blade and fine sandpaper, and then tint with a special dye of the appropriate shade.

Finally, the top of the restoration area is covered with liquid glue.

After restoration, fragile figurines can be completely covered with a layer of transparent varnish. This will renew the shine of the item and give it an additional margin of strength.

Porcelain, faience and ceramics

Products made from these materials usually have thicker walls and a more porous clay structure at the fracture. To restore a broken object in this situation, almost any universal glue will do. The main thing is to strictly adhere to the technological process:

• Collect all shards, wash them from dust, dirt and other deposits (it is better to use a kitchen detergent for dishes).
• spread the wreckage on a clean, dry towel and dry patiently.

Clay material is dry and porous. It is necessary for all the water from the fragments to evaporate.

• Using a clean white cloth soaked in any solvent, carefully and thoroughly wipe the edges and breaks of all pieces.

The rag must be undyed. Otherwise, under the influence of the solvent, it may “fade” and paint the pieces of porcelain an undesirable color.

• apply to the surfaces to be bonded thin layer selected glue and allow it to dry.

This takes from 10 to 30 minutes and depends on the manufacturer.

• then the second layer is applied and the “constructor parts” are quickly and tightly pressed against each other.

To avoid having to sit with a vase or cup in your hands for the next few hours, you can secure the object with a rubber band.

• let the product dry for several hours (written on the tube of glue), remove the tourniquet and check the quality of the seams.

So in an accessible way You can glue almost any objects that are so difficult to part with.

Products made of porcelain and ceramics can be glued with adhesives “Mars”, “Polyvinyl acetate”, BF-2, “Rapid”, MTs-1, “Mekal”, “Kittifix”, “Supercement”, Ago”, “Elastostil-2”, EDP , EPO, "Latex" and "Unicum". However, it should be taken into account that Supercement and Ago glues do not form sufficiently strong seams, BF-2 glue is colored, and polyvinyl acetate glue is not waterproof.

When gluing porcelain with Rapid, Ago, Mars, MC-1, Latex, Unicum, Kittifix and Mekol adhesives, degrease the surfaces with a swab moistened with acetone, apply a layer of glue to both surfaces and let Let it dry for about 20 minutes. After this, apply a second layer of glue, connect the surfaces to be glued, pressing them firmly against each other using a rubber band, clamp or some other device, and keep them in this position for 3 hours. The final setting of the seam occurs within 2 days.

When working with “Rapid”, “Ago”, “Kittyfix” and “Mekal” adhesives, you can use another method: coat the grease-free surfaces with glue only once and immediately connect them, squeezing them with a tourniquet or in a clamp.
Porcelain can be glued using Elastostil-2 glue. This is a two-component waterproof adhesive that is sold packaged in two aluminum tubes. Before use, the contents of the tubes are mixed in a 1:1 ratio and mixed thoroughly. Surfaces must first be degreased and thoroughly dried. The prepared glue is applied to both surfaces and the parts are compressed.

During the 3 days while the adhesive joint is setting, under no circumstances should water fall on it.
Strong and waterproof adhesive seams are produced by EDP, Mekal, EPO, Mars, Rapid, Kattifix, Elastostil-2, Latex and Unicum adhesives.

For gluing sanitary ware made of porcelain and ceramics, in addition to traditional adhesives, compositions that you can make yourself are also used.

To glue glass or porcelain products that will not be exposed to heat, you can prepare a paste of gypsum and quicklime: 50 g of gypsum, 10 g of quicklime, 1 egg white and 10 g of water are mixed immediately before use.

To glue porcelain or ceramics, 10 g of kaolin and 1 g of calcined borax are mixed with water to a paste. Products glued with such a paste are fired over high heat until light red heat. The seam is heat and water resistant.

To glue porcelain products, you can prepare the following paste: mix 20 g of ready-made casein powdered glue with 8 g of silicate glue. In this case, the glued product will not be afraid of water, since the result will be a fairly water-resistant adhesive seam.

To glue porcelain objects, you can also prepare a composition of wood glue: add 12 g of starch and 7 g of chalk to the wood glue solution. The resulting mixture is thoroughly mixed. The glue is not heat resistant.

To glue glass objects, take 100 g of liquid glass per 20 g of dry casein glue. When gluing glass with this composition, the contact method is used: a layer of glue is applied to both surfaces to be glued and allowed to dry slightly. After this, the objects to be glued are connected and heated strongly.

Porcelain and earthenware can be glued with a paste, which is obtained by adding gypsum to a 3% gelatin solution. The paste is prepared immediately before use. Another glue for gluing porcelain and earthenware is also prepared on the basis of gelatin: a 25% gelatin solution is mixed with an equal amount of vinegar essence.

Most often, people throw away these things with great regret. However, if the product is dear to you as a memory or necessary in everyday life, you can try gluing it together.

Questions immediately arise. ? Which glue to choose for gluing porcelain? Is it possible to prepare your own adhesive solution for ceramics?

It should be noted here that today there are a lot of varieties of glue and it is necessary to build on its universal properties.

1. Henkel Moment glue
2. UHU Creativ glue for crafts
3. Universal Moment

VIDEO INSTRUCTION

Glue can be natural or synthetic. You can prepare an organic adhesive solution for ceramics yourself.

To do this you need:

1. Dissolve 100 grams of slaked lime and 100 grams of sugar in one liter of water.
2. Once the water boils, cook the solution for three hours.
3. Afterwards, let the lime-sugar mixture settle and drain the water.
4. Add 0.5 kg of crushed tile adhesive, for example from Knauf.
5. Do not touch the resulting mixture for 12 hours.
6. Use the resulting adhesive solution cold.

You can also use synthetic glue; it is sold in special construction stores.

The most suitable options are:

• Mekol,
• Elastostil-2,
• Mars,
• Rapid,
• MC-1,

They perfectly glue ceramics and earthenware and have high technical performance.

If this happens and you break a ceramic vase, a chip occurs on the handle of a kitchen cup, or something dear to you cracks, you need to figure it out. how to glue ceramics to ceramics.

To do this, you can purchase narrow-profile ceramic adhesive.

Ceramic is much more difficult to glue than porcelain.

Therefore, you should be guided by the basic rules:

1. We clean the surfaces to be glued from dirt and dust.
2. We degrease the component parts of the object, and then dry them well.
3. Apply a thin layer ceramic glue to the required area.
4. If the parts to be glued have an uneven texture, apply a second layer of glue.
5. Connect the parts to be glued, pressing them down with force.
6. Fix the product in a clamped state for the period of time specified in the glue instructions.
7. You can use the item again after a couple of days, when the glue has completely set.

To fix the product to be glued, you can use a tourniquet, and if the object is small, stick it into a container with sand. This will contribute to reliable gluing and tight connection of all parts into a single whole.

How to glue porcelain

To repair a porcelain product you will need:

• epoxy glue such as EDP,
• container for diluting glue,
• stick for applying the composition.

Operating procedure:

1.Mix the resin and hardener in a ratio of 1:10 and heat with a household hair dryer.

2. Apply the composition to the place where we will glue the fragments. Leave for a few minutes.

3. We connect the fragments of the broken product.

For complete drying, it must be left for 24 hours.

For gluing ceramics and earthenware, you need to follow the same rules. First, prepare the connecting parts by cleaning them from various types of contaminants, degreasing them with a solvent and drying them.

If you need to glue small pieces together, choose cyanoacrylate-based glue. It is packaged in small tubes and is suitable for one-time use only.

If you have to glue large parts, you can weld the glue yourself.

1. Use six parts of liquid glue,
2. Two parts of sifted river sand and,
3. One part crushed glass. This composition will give the glue strength and quality, but after gluing the seam will remain noticeable.

VIDEO ON THE TOPIC

An easy DIY option is casein-based glue. To prepare it you will need water, borax, casein, and a few drops of formaldehyde. This mixture will harden in 2-3 hours. And yet, many resort to gluing ceramics and earthenware adhesive solution based on gypsum.

Do not rush to throw away a damaged item, be it a porcelain vase, ceramic cup, or earthenware sink. Try to breathe a second life into your favorite piece of furniture on your own.

Special instant adhesive for porcelain and ceramics UHU Porzellan Keramik is absolutely transparent and therefore provides an almost invisible connection. The thinner the adhesive layer, the more reliable the connection and the faster the glue sets, so it is not suitable for filling cracks and voids. Adhesive connection withstands SHORT-TERM exposure to water.
Bonded products can also be exposed to temperatures over a wide range: UHU Porzellan Keramik can withstand any temperature up to +100°C.

Instructions for use:

The prerequisite for successful gluing is a perfectly clean and dry surface. If the material allows this, it is recommended to repeatedly wipe the gluing area with solvents (acetone, etc.).
- Apply UHU Porzellan Keramik porcelain and ceramic adhesive to one of the surfaces to be glued, immediately connect it to the second and squeeze the surfaces to be glued. Excess glue can be removed using paper napkin immediately after use.
- Glue for porcelain and ceramics UHU Porzellan Keramik glues, depending on the material, in a few seconds or in a few minutes. Maximum bond strength is achieved after 12 hours.
The adhesive joint can be separated by heating up to 180 degrees. C, as well as long-term exposure to water or acetone.
High humidity speeds up the gluing process, so you can blow on the applied glue to speed up the process. Use acetone to remove glue residue.

Precautionary measures:

The glue bonds very quickly when high humidity(for example, coming into contact with sweat, sebum, tears, etc.), so you need to be extremely careful when working with it. In case of contact with skin, rinse the affected area with warm water. soapy water for a long time, then separate the layer of glue (without using significant force!) and apply a rich cream to the damaged area.
If your fingers are stuck together, hold them in warm water and then try to separate them with a paper clip or wire. You can also remove the glue with acetone or nail polish remover. Because organic solvents strongly degrease the skin, it is recommended to apply hand cream afterwards. Remaining marks on the skin can be removed using pumice.
If glue splashes get into your mouth or eyes, they must be kept open and washed with plenty of water. It has a strong odor, so applying glue in large quantities It is recommended to produce in ventilated areas.

Storage:

After use, the glue must be closed and stored in a cool place (refrigerator, etc.).

A marker is a reservoir of paint that flows to a nylon or felt tip. This is a modern and convenient tool for drawing and writing...

And again the section “Creative Gurus”. Today we will talk about the father of pop art, who largely shaped the face of modern art - Andy Warhol. Like any creative personality, Warhol was extremely versatile: producer, musician, fashion designer, director, creator of Interview magazine and, of course, founder of the famous Factory, where his works were replicated.

We continue to talk about creative people who charge us with their creative energy. Next in line is Takashi Murakami

Using liquid acrylic instead of ink in pens (part I)

Pens are usually refilled with ink. Although traditional ink works great in Everyday life, they may be difficult to use in artistic creation...

Why are some of the paint samples made using the same pigment so different from each other?

We've received a lot of questions about varnishing watercolors, and we even have a special information page that discusses the process of using varnishes...

Waterproof Indian mascara and shellac-based primers

Strangeness arises when you try to apply any of our mediums, gels, primers or paints over Indian ink...

Today we will look at the technique of transferring a design using Fiber Paste - a paste with the effect of handmade paper...

Understanding the reasons for the occurrence of these irregularities in the paint film will allow not only to correct the artist’s actions, but also to show him how, in a sense, he can take advantage of...

Delta E - the key to understanding light fastness

Simply put, Delta E is a number that represents the amount of difference between two colors or, in the case of testing a single sample...

How to get from point A to point B in watercolor? How to develop a “creativity habit”? What three tips can you give to beginning watercolor painters? – The artist Sergei Kurbatov talks about all this...

You see, there is no something divine that is once given to you in diapers, and you inevitably become something a unique person. You become this unique person when you create it within yourself...