Communication well kks 3 sizes. Types and features of installation of cable wells. Features of the design and material used

Wells telephone KKS 3-10(80) GEK are made from high-strength frost-resistant concrete for the construction of telecommunications, engineering and technical local networks. They are indispensable for protecting cables from possible damage and provide fast access to networks during their inspection, installation, repair and operational maintenance.

Scope of application

There are several modifications of telephone wells. The smallest in size is KKS-1, and the largest is KKS-5. The wells are designed to provide easy access inside for one person to do the job. The cables located in such KKS are under reliable protection from any type of precipitation. In addition to the size range, telephone wells are divided into heavy and light. Heavy ones are located under roadway, and the lungs are under pedestrian areas. Wells can be installed in a pre-prepared pit. Installation under the roadway at a depth of at least 330 mm is permissible; under pedestrian paths, sidewalks and courtyard areas at a depth of at least 250 mm. The ground must be carefully leveled.

Seams need to be processed cement mortar, since the well must be sealed to prevent moisture from entering network cables. It is better to install KKS in soils that are non-aggressive towards concrete.

Design and configuration of wells

The telephone well consists of two parts - the upper (with half the side walls and the upper ceiling) and the lower (with half the side walls and the bottom). The joining of these parts is carried out on the construction site by welding the embedded parts. Top part consists of a round hole, above which a reinforced concrete ring for a cast iron hatch and the hatch itself are installed. Telephone wells with abbreviation "GEK" are equipped with brushes and brackets of types KKP-60 or UKP-65 made of strip steel. Brackets are equipped anchor bolts and nuts. The telephone well should only be covered with a cast iron hatch of the “t” type (heavy).

The technical purpose of wells can be stationary, through-hole, corner and branch. A stationary well is a well that is used to enter cables. The gateway is placed on straight sections of the canal. Corner and branch telephone wells are installed in places where the channel turns and branches.

Specifications

• Water resistance W2 allows the well to withstand water pressure equal to 2 atm
• Frost resistance F75 provides a minimum of 75 freezing and thawing cycles before the material begins to deteriorate
• Tempering strength of 70% guarantees installation and loading and unloading operations without compromising the quality of the product
• Concrete of strength class B22.5 (M200) and higher can withstand mechanical loads, so telephone wells can be installed both in pedestrian areas and under highways
• Product reinforcement steel frames class A100, A200 and A300 to achieve enhanced product strength
• Telephone wells comply with the standards and requirements of TU 14188-83, which contains all the data on the technology, properties of the materials used, labeling, transportation and storage of finished products

Manufacturing process

The production of telephone wells is carried out using a bench or aggregate-flow method. Pre-prepared reinforcing frames are fixed to the platforms. Next, the frames are concreted. Raw concrete is sent for thermal drying to achieve regulatory quality standards. The combination of heavy concrete and steel guarantees high strength and reliability of the finished product. Based on a set of acceptance tests that all finished products undergo, certification documents are issued.

Storage and delivery

Finished products are stored in stacks of two or three rows. Laying products on their sides is not permitted. During transportation, each well must be secured and lined with wooden spacers to avoid damage. Loading and unloading of KKS is carried out only with the help of special equipment.

Company "DSK-Stolitsa" delivers telephone wells KKS 3-10(80) GEK via transport companies, observing the established transportation requirements.

Delivery to the site is carried out according to specifications indicating the number of products of each brand.

The ZhBI TORG company offers telephone wells KKSr-3 10 (80) in Moscow. We produce reinforced concrete products ourselves and carry out delivery on our own. This allows us to respond to customer messages around the clock, ensure there are no unnecessary markups and guarantee quality.

Characteristics and dimensions of wells KKSr-3 10 (80)

This product is used for laying electrical networks and communication lines. Wells KKSr-3 10 (80) provide protection against soil collapse, water seepage, and debris. By its design, the product is a combination of two volumetric box-shaped elements. During the installation process, one camera is created from them.

The full designation of the element looks like KKSr-3-10(80) GEK, where:

• KKS - cable communication well.
• p - branching type.
• 3—size number.
• 10(80) — norm ultimate load per element. It is believed that 10 tons is enough for installation in places where light loads are placed on the product - on pedestrian areas, sidewalks and parks. A load limit of up to 80 tons allows you to easily install these types of products on the roadway.
• HEC. This designation indicates that the product is supplied fully assembled and ready for installation.

Features of the design and material used

At the top of the product there is a special hole with a diameter of 600 mm, which is designed so that you can install a hatch or well ring. In addition, there are niches in the walls of the well in which additional holes can be made for pipes. The most commonly used models are made of polypropylene or asbestos cement.

We supply products made from high-quality concrete and reinforced with steel elements. The tempering strength of the concrete used is at least 80%, and the strength class is B22.5. The product will withstand moisture thanks to its W6 waterproof rating. Frost resistance of F200 indicates that the product can be used in the Russian climate.

The products of our company are used when it is necessary to ensure construction engineering structures, lay communication networks. Leave

Cable communication wells KKS-3-10 and KKS-3-80 are specialized products intended for construction cable duct and laying cable communication networks. Communication wells KKSr-3 are manufactured at the reinforced concrete plant in several versions. First of all, they differ design load on the:

• KKSr-3-10 - designed for light loads, this means its installation in green spaces, pedestrian areas and open areas.
• KKSr-3-80 are designed for installation sites where intense loads are expected, such as roadways.

The wells also differ in their completeness; there are 2 types: G - bare and GEK - with ruffs and brackets (KKCH consoles are not included in the package).

KKSr-3 G / GEK consist of two halves: upper and lower. In horizontal section, the well has an octagonal shape. All KKS wells produced at the ZhBI-1 Plant are universal and can be used as walk-through, corner and branch wells. This versatility is made possible by non-reinforced recesses for the ability to punch holes for the entry of channels. Also, the presence of niches gives an additional advantage, it becomes possible to make holes only required diameter, for inserting the pipes used. Each niche of the KKS-3 well is designed to accommodate 6 channels (by channels we mean 100 mm in diameter). It is recommended to cover unused niches with the solution flush with the wall of the well.

On the top of the well there is a hole for organizing a manhole with a diameter of 600 mm intended for installation and. For cable wells, connections are provided that differ in size, load capacity and geometric characteristics. Such hatches have on the lid letter designation GTS (city telephone network) and are manufactured for both light loads (10) and heavy loads (80), are designated respectively by the letters and.

Where to buy cable wells KKSr-3 G / GEK

You can order and buy cable wells KKSr-3-10 G / GEK and KKSr-3-80 G / GEK with delivery throughout Moscow, the Moscow region and throughout Russia. will help you select products, calculate the current price, complete your order and organize delivery. The price of wells KKS-3-80 G depends on the quantity necessary products, since the products themselves are very voluminous and the loading rate per vehicle is 20 tons. Makes up – 6 products.

Cable wells communications KKS 3-80 or, as they are also called, telephone wells are a part of communication, cable ducting, which exists for pulling and servicing communication cables, for example, GTS or the Internet. Cable wells vary in size and modification. They are made of reinforced concrete, this strength is very important and is explained by the fact that they need to withstand the load of soil pressure. A load of 80 indicates that this cable well can be located under roadways and highways. Communication wells are made from heavy concrete. Thanks to this, they can reliably accommodate equipment that allows automatic mode regulate the distribution of Internet traffic. This modern look communication needs reliable protection from environmental conditions and providing access only when necessary, without the entry of unauthorized persons.

Each telephone well consists of upper and lower blocks, which are joined directly on the construction site using welding. Inlet, round shape, located on top, consists of reinforced concrete ring and a cast iron hatch. Some cable wells can be equipped with nuts, brackets and brushes, then they are marked with the abbreviation “KKS 3-80 GEK”. The communication cable is attached to the brackets. The number of brackets and consoles depends on what type of KKS well. The brackets are made of steel and are equipped with anchor bolts and nuts. This well should be covered with a cast iron hatch of the “T” type - heavy. Transportation of KKS cable wells is carried out by car. The car must be open top. During transportation, wells cannot be stacked on top of each other. Installation of the KKS-3 telephone well should be carried out in a pre-prepared pit. The ground must be leveled before this.

All seams must be well treated, coated with cement mortar, so that the well is sealed and moisture does not get into the cable connections. In order for the cement to “grab” better, each of the reinforced concrete parts is treated with water, simply moistened. To protect communication cables inside wells, special casings and cable channels are used. Usually this plastic pipes, which run underground and branch out in telephone wells. Such wells are buried about a meter into the ground. In such a well there must be access to all the elements that are installed inside.

If an inspection is being carried out on the line, then access should be easy and quick thanks to a simple shutter system. There is enough space in such a well for signalmen to carry out all the necessary checks and work. If brushes and brackets are not provided, the customer can select the ones he needs. The weight of cable wells depends on its index.

Considering that environment, in this case the soil, should not be aggressive to materials such as concrete. In my own way technical purpose wells are stationary, walk-through, corner and branch wells KKSr 3-80. If you count in the direction from the shaft, the stationary communication well is the first one, used to enter cables. Walkways are constructed on straight sections of extended canals. Corner or branching wells are installed where it is necessary to turn or branch the cable channel.

In the age of communication technologies in village and city infrastructure, it is impossible to do without them. They allow you to implement communications in the most convenient way. In some cases, it is technically impossible to install a reinforced concrete telephone well, then their plastic counterparts come to replace them, which, of course, are not as durable and strong, but are also in demand because they are more cheap material, easier to operate and install. But most builders still give preference to traditional materials; I prefer not to skimp on quality. The service life of such cable wells is practically unlimited; it is guaranteed to be about seventy years.

Description

KKS 3-10 GEK - reinforced concrete well measuring 195 x 116 x 176 cm, with high structural strength, which allows it to withstand heavy loads during operation. This is an important element of underground utilities, providing free and safe access to communication lines for preventive maintenance and urgent repair work. The production of KKS telephone wells is regulated by strict standards, therefore ready-made designs They are easy to install, durable and can easily withstand the effects of various negative factors.

Product Description

Reinforced concrete telephone well KKS 3-10 GEK is used in underground elements utility networks and plays an important role in construction, providing reliable access to communication lines and telecommunications. The design of KKS wells allows specialists to carry out renovation work, laying communication cables and preventive inspection. In particular, KKS telephone wells vary in size. The smallest size is marked KKS-1, and the largest KKS-5.

Product marking

For an example of marking telephone wells, consider “KKS-1-10-M-GEK”, where:

• KKS - cable network well;
• 1 - product size;
• 10 - installed under the pedestrian area;
• M - monolithic well;
• GEK - equipped with brushes and brackets (G - not equipped).

Product type characteristics

Size classification:

Length – 145 cm, width – 110 cm, height – 86 cm.

Length – 135 cm, width – 103 cm, height – 156 cm.

Length – 195 cm, width – 115 cm, height – 180 cm.

Length – 239 cm, width – 132 cm, height – 200 cm.

Length – 300 cm, width – 165 cm, height – 204 cm.

Reinforced concrete telephone wells are classified according to size and degree of load. Wells of this type have two load levels - 10 (under the pedestrian area) and 80 (under the roadway).

Telephone wells KKS are the most important elements underground utilities and are responsible for convenient access to communication lines for their preventive maintenance and urgent repairs. KKS 3-10 GEK is a high-strength model with dimensions of 195 x 116 x 176 cm, which is not afraid of heavy operating loads, since it is made of high-class concrete in accordance with current standards. The design also easily copes with negative environmental factors, is quite simple to install and is durable. All these characteristics determine its demand.

Question answer

- Delivery price?
Delivery is calculated based on the distance of your facility, from the warehouse, as well as the tonnage and dimensions of the products.

-Where are you bringing it from?
Delivery is carried out directly from production. Production facilities are located throughout the central region, and before entering our network, they undergo strict quality control by the legal, accounting and quality departments.

- Where is the post office?
For the convenience of users, we have created a system for distributing the load on managers; if 1 person checks mail, this significantly slows down the work or even leads to the fact that read letters are lost. You can leave a request through the form at the top of the site “Leave a request”, it will go to a free manager and they will call you back within 5 minutes.

- You have mobile number?
For the convenience of users, we have created a system for distributing the load on managers; if a mobile phone is specified, then only 1 person can talk on it, and it will be difficult to reach him during the season.

- Why so expensive?
The price of a product consists of several components, the main one being the cost of the material, which determines the quality of the final product. There is also a markup from the factory and a markup from the trading company, we work on the terms of a dealer discount, so we don’t have a markup separate from the factory, we make money from the fact that the factory shares part of its profit with us, and we, in turn, provide the factory with volume to ensure uninterrupted operation .

- Why can’t you order less than 15 thousand? Do you work only in wholesale?
Some items are manufactured in nearby areas and shipping of these items adds significant cost to the product. We calculated that when ordering more than 15 thousand, the benefit from purchasing products from us becomes greater. If you have a small request for products that are manufactured in your area, it will be cheaper to purchase products at nearby factories. Unfortunately we have this moment There is not a single plant in the Moscow region that has passed our quality check.

- Where can I pick it up?
The products are manufactured in different factories, region and city, the manager can tell you, because the factory is different for each product.

- Why is delivery so expensive?
Delivery is calculated based on the distance of the object from the factory warehouse. The delivery cost is divided by the number of items based on the weight of the product; if you order 1 item, the entire delivery cost will fall on it, but if there are 10 items in the order, the delivery price will be equally distributed over these 10 items.

- Do you work with VAT?
Yes, the company Beton Project LLC works for OSNO and is a VAT payer. All prices on the website include VAT.

- Why is only the office listed on the website and not the plant?
We are a dealer of factories and operate at our office address. Because Our list contains a significant number of factories that have passed our inspection; it is not rational to post all the addresses of factories with products, which would complicate the search for the right factory. If you are interested in where this or that product can be exported, you can always check with the Manager or use our delivery.

- Do you have a warehouse in Moscow?
We do not have a warehouse in Moscow or the Moscow region, because... this will have a negative impact on the cost of the product because it will entail additional costs.

- What kind of plant? What is the name of?
The products are manufactured at different factories, you can always come to the factory and see for yourself the quality of our products. Also, if you have any doubts, you can pay for the products directly to the factory.