Aluminum and products made from it. II. Requirements for technical strengthening of cash register premises of enterprises Thickness of at least 2

1. Protection class 1 fencing(the minimum required degree of protection of an object from penetration) - fences made of various non-permanent structures with a height of at least 2 m.

2. Protection class 2 fencing(average degree of protection of the object from penetration) - solid wooden fencing (board thickness at least 40 mm), metal mesh or lattice with a height of at least 2 m.

3. Protection class 3 fencing(high degree of protection of the object from penetration) - reinforced concrete, stone, brick, solid metal fences with a height of at least 2.5 m.

4. Protection class 4 fencing(special degree of protection of the object from penetration) - monolithic reinforced concrete, stone, brick fences with a height of at least 2.5 m, equipped with additional fencing.

APPENDIX No. 3.

GATE CHARACTERISTICS

1. Gate 1 protection class(the minimum required degree of protection of an object from penetration) - gates made of non-permanent structures with a height of at least 2 m.

2. Gate 2 protection class

combined, lattice or slatted gates made of metal structures, having or corresponding to the category and class - not lower than O-II, in accordance with GOST 51242-98;

wooden gates with continuous filling of panels with a thickness of at least 40 mm;

lattice metal gates made from steel rods with a diameter of at least 16 mm, forming a cell no more than 150 x 150 mm and welded at each intersection

The height of the gate is at least 2 m.

3. Gate 3 protection class

combined or solid gates made of metal structures, having or corresponding to the category and class - not lower than U-I, in accordance with GOST 51242-98;

wooden gates with a continuous filling of boards no less than 40 mm thick, sheathed on both sides with steel metal sheet thickness of at least 0.6 mm;

combined or: solid gates made of steel sheet with a thickness of at least 2 mm, reinforced with additional stiffeners and upholstered on the inside with boards with a thickness of at least 40 mm.

The height of the gate is at least 2.5 m.

4. Gate 4 protection class

solid gates corresponding to the category and class - not lower than C-1 according to GOST 51242-98;

solid gates made of steel sheet with a thickness of at least 4 mm, reinforced with additional stiffening ribs.

The height of the gate is at least 2.5 m.

APPENDIX No. 4.

CHARACTERISTICS OF DOOR STRUCTURES

1. Door designs 1 protection class

doors with glass panels in metal frames or without them: ordinary glass, grades M 4 - M 8 in accordance with GOST 111-90, tempered in accordance with GOST 5727-88, reinforced in accordance with GOST 7481-78, patterned in accordance with GOST 5533-86, three-layer (" triplex") according to GOST 5727-88 or protective class AI according to GOST R 51136-98;

wooden internal doors with solid or fine-hollow filling according to GOST 6629-88, GOST 14624-84, GOST 24698-81. The thickness of the canvas is less than 40 mm;

wooden doors with glass fragments from regular sheet grades M 4 - M 8 according to GOST 111-90, reinforced according to GOST 7481-78, patterned according to GOST 5533-86, tinted according to OST 3-1901-85, safe according to GOST R 51136-98 glass The thickness of the glass fragment is not standardized;

lattice metal doors of arbitrary design, made of steel rods with a cross-section of at least 78 mm 2, forming a cell with an area of ​​no more than 230 cm 2 and welded at each intersection.

2. Door structures of 2 protection classes(average degree of object protection against penetration):

doors corresponding to the category and stability class O-II and higher according to GOST R 51242-98;

doors corresponding to stability class IA according to GOST R 51224-98;

external wooden doors (type NS according to GOST 24698-81) with continuous filling of the panels with a thickness of at least 40 mm;

doors with glass panels in metal frames or without them using protective glazing of class A2 and higher according to GOST R 51136-98 or ordinary glass, laminated protective film, providing glazing stability class A2 and higher GOST R 51136-98;

lattice metal doors made of steel rods with a diameter of at least 16 mm, forming a cell no more than 150 x 150 mm and welded at each intersection. Along the perimeter, the lattice door is framed with a steel corner measuring at least 35x35x4 mm;

lattice sliding metal doors made of strip with a cross-section of at least 30 x 4 mm with a cell no more than 150 x 150 mm.

3. Door structures of 3 protection classes(high degree of protection of the object from penetration):

doors corresponding to category and class stability U-I and higher according to GOST R 51242-98;

doors corresponding to stability class IB according to GOST R 51224-98;

wooden doors with continuous filling of sheets with a thickness of at least 40 mm, reinforced with upholstery on both sides with sheet steel with a thickness of at least 0.6 mm with the sheet folded to inner surface doors or at the end of the leaf with an overlap with fastening along the perimeter and diagonals of the leaf with nails with a diameter of 3 mm and a pitch of no more than 50 mm;

wooden doors with continuous filling of the panels, a thickness of at least 40 mm, with additional reinforcement of the panels with metal overlays;

doors with glass panels in metal frames or without them using protective glazing of class B1 and higher according to GOST R 51136;

metal doors with a thickness of outer and inner steel cladding sheets of at least 2 mm.

4. Door structures of 4 protection classes (special degree of protection of the object from penetration):

doors corresponding to category and stability class C-II and higher according to GOST R 51242-98;

protective cabin doors in accordance with GOST R 50941-96;

protective doors according to GOST R 51072-97;

doors for storage rooms, safe rooms in accordance with GOST R 50862-96.

APPENDIX No. 5.

WAYS TO STRENGTHEN DOOR STRUCTURES

To strengthen wooden door frame It is recommended to frame it with a steel corner measuring at least 45x28x4 mm, and also to fix it in the wall with steel brushes (crutches) with a diameter of at least 10 mm and a length of at least 120 mm. It is recommended to fasten it to the wall using metal pins, the distance between which is no more than 700 mm.

Strengthening the strength of doors (gates and gates) is achieved through the use of safety linings, a safety corner lock plate, massive hinges, and reinforcement of the door leaf.

Hinges for doors, gates, and wickets must be durable and made of steel. Fastening should be carried out using screws, screws or welding, depending on the material of the doors, gates, gates.

When opening doors (gates, gates) “outwards”, end hooks (anchor pins) must be installed on the side of the hinges to prevent the door from being removed if the hinges or their mechanical damage. End hooks should be made of steel rod with a diameter of 6-8 mm.

It is recommended to make door linings, sockets, shields from a steel strip 4-6 mm thick and at least 70 mm wide. They must be secured using bolts. The bolts passed through the door are secured with inside premises using washers and nuts with riveting the end of the bolt.

APPENDIX No. 6.

CHARACTERISTICS OF WINDOW STRUCTURES

1. Window designs 1 protection class(minimum required degree of protection of an object from penetration) - windows with ordinary glass(glass grade M 4 - M 8 according to GOST 111-90, thickness from 2.5 to 8 mm).

2. Window designs of class 2(average degree of object protection against penetration):

windows of a special design with protective glazing class A2 and higher in accordance with GOST R 51136-98 or ordinary glass covered with a protective film, ensuring glazing stability class A2 and higher in accordance with GOST R 51136-98;

protective structures corresponding to the category and stability class O-II and higher according to GOST R 51242-98.

wooden shutters with continuous filling of canvases with a thickness of at least 40 mm;

panels or wooden shutters made of boards or plywood 12 mm thick, upholstered with steel sheets no less than 0.6 mm thick:

metal gratings of any design, made of steel rods with a cross-section of at least 78 mm 2, forming a cell with an area of ​​no more than 230 cm 3 and welded at each intersection.

3. Window designs of 3 protection classes(high degree of protection of the object from penetration):

windows of a special design with protective glazing of class A3 and higher according to GOST R 51136-98;

windows with regular glass, additionally protected:

protective structures corresponding to the category and stability class U-I and higher according to GOST R 51242-98;

protective structures corresponding to stability class IB according to GOST R 51222-98;

panels or wooden shutters with continuous filling of the panels with a thickness of at least 40 mm, upholstered on both sides with steel sheets with a thickness of at least 0.6 mm;

metal gratings made of steel rods with a diameter of at least 16 mm, forming cells no more than 150x150 mm or other structures of appropriate strength.

4. Window designs of 4 protection classes(special degree of protection of the object from penetration):

windows with ordinary glass, additionally protected by protective structures corresponding to category and stability class C-II and higher according to GOST R 51242-98;

windows of a special design with protective glazing of class BI and higher according to GOST R 51136-98;

windows with bulletproof glass (armored glass) according to GOST R 51136-98 class 1 and higher;

glazing of protective cabins in accordance with GOST R 50941-96.

APPENDIX No. 7.

CHARACTERISTICS OF BUILDING STRUCTURES

1. Building construction 1 protection class(minimum required degree of protection of an object from penetration):

plaster, gypsum concrete with a thickness of at least 75 mm;

panel board wooden structures thickness of at least 45 mm;

structures made of logs or timber 100 mm thick;

frame partitions with a thickness of at least 20 mm covered with metal, including profiled sheets with a thickness of at least 0.55 mm;

brick partitions 138 mm thick according to SNiP III-17-78;

partitions made of lightweight thermal insulating concrete less than 300 mm thick;

internal Wall panels 100 mm thick according to GOST 12504-80;

hollow reinforced concrete structures 160 mm thick according to GOST 9561-91;

partitions made of glass profiles in accordance with GOST 21992-83 and glass blocks in accordance with GOST 9272-81.

2. Building structures of protection class 2(average degree of object protection against penetration):

structures made of logs or timber with a thickness of at least 200 mm;

brick walls 250 mm thick according to SNiP III-17-78,

hollow reinforced concrete slabs 220 mm, 260 mm, 300 mm thick according to GOST 9561-91 from lightweight concrete and 160 mm thick from heavy concrete;

solid reinforced concrete floors thickness 120 mm, 160 mm according to GOST 12767-94 from lightweight concrete;

external wall panels in accordance with GOST 11024-84, internal in accordance with GOST 12504-80 and wall blocks in accordance with GOST 19010-82 made of lightweight concrete with a thickness of 100 to 300 mm;

walls made of monolithic reinforced concrete according to SNiP III-15-80, made of heavy concrete, up to 100 mm thick;

building structures of 1st protection class, reinforced steel mesh according to GOST 23279-85 with a rod thickness of 8 mm and a cell of 100x100 mm.

3. Building structures of protection class 3(high degree of protection of the object from penetration):

brick walls more than 380 mm thick according to SNiP III-17-78;

hollow reinforced concrete floors with a thickness of 220 mm, 260 mm, 300 mm according to GOST 9561-91 from heavy concrete;

solid reinforced concrete floors with a thickness of 120 mm and 160 mm according to GOST 12767-94 made of heavy concrete;

external wall panels in accordance with GOST 11024-44 and wall blocks in accordance with GOST 19010-82 made of lightweight concrete with a thickness of more than 300 mm;

external wall panels in accordance with GOST 11024-84, internal in accordance with GOST 12504-80, wall blocks in accordance with GOST 19010-82 and walls made of monolithic reinforced concrete in accordance with SNiP III-15-80 with a thickness of 100 to 300 mm made of heavy concrete;

building structures of protection class 1, reinforced with steel bars welded at joints with a thickness of at least 10 mm with a cell of no more than 150x150 mm;

building structures of protection class 2, reinforced with steel mesh in accordance with GOST 23279-85 with a rod thickness of 8 mm and a cell of 100x100 mm.

4. Building structures of 4 protection classes(special degree of protection of an object from penetration) - structures corresponding to the 5th and higher class of burglary resistance according to GOST R 50862-96.

APPENDIX No. 8.

SCHEMATIC STORAGE DEVICE

Figure P8.1 - Schematic design of a valuables storage facility

APPENDIX No. 9.

CHARACTERISTICS OF LOCKING DEVICES

1. Locking devices of 1st protection class(the minimum required degree of protection of an object from penetration).

1.1. Mortise and rim locks:

1st class according to GOST 5089-97;

suvaldnye. At least 6 levers for a mortise lock or 5 for a overhead lock;

pin. At least 6 code pins;

lamellar. At least 6 code plates;

disk. At least 6 code disks;

electromagnetic with pull-off force - 150 kg.

The cross-section of the bolt of mechanical locks is at least 250 mm 2, the length of the head is at least 30 mm. Bolt material: steel, aluminum alloys, brass.

1.2. Padlocks:

pin. The number of code pins is at least 5. The design of the deadbolt is arc. The diameter of the bolt (shackle) is at least 10 mm,

disk. The number of code disks is at least 6. The design of the bolt is arc. The diameter of the bolt is at least 10 mm.

1.3. Garage locks - Disc and lever locks - at least 8 combination discs and 5 levers. The bolt material is steel. The cross section of the bolt is at least 300 mm 2. The overhang of the bolt is at least 25 mm, the length of the bolt head is at least 35 mm. The thickness of the body sheet is at least 1.5 mm.

2. Locking devices of class 2 protection(average degree of protection of the object from penetration).

2.1. Mortise and rim locks:

2 class according to GOST 5089-97;

suvaldnye. At least 6 levers for a mortise lock or 5 for a overhead lock;

pin. At least 8 code pins;

lamellar. At least 7 code plates. Availability of protection against drilling and folding;

disk. At least 8 code disks. Availability of protection against drilling and folding;

electromagnetic with pull-off force - 250 kg.

The cross-section of the bolt of mechanical locks is not less than 300 mm 2, the length of the head is not less than 35 mm. The bolt material is steel.

2.2. Padlocks:

pin. The number of code pins is at least 6. The design of the deadbolt is arc. The diameter of the bolt is at least 10 mm. Availability of protection against sawing of the bolt;

disk. The number of code disks is at least 8. The design of the bolt is arc. The diameter of the bolt is at least 10 mm. The presence of protection against sawing the bolt.

2.3. Garage locks - disc and level locks. At least 8 code discs and 6 levers. The bolt material is steel. The cross section of the bolt is at least 500 mm 2. The overhang of the bolt is at least 30 mm, the length of the bolt head is at least 60 mm. The thickness of the body sheet is at least 2 mm. For disc locks - anti-roll protection.

3. Locking devices of 3 protection classes(high degree of protection of the object from penetration).

3.1. Mortise and rim locks:

3 classes according to GOST 5089-97;

suvaldnye. At least 6 levers for a mortise lock or 6 overhead locks. Availability of protection against drilling of the bolt shank post;

pin. At least 10 code pins. Availability of protection against master keys, drilling, folding;

lamellar. At least 7 code plates. Availability of protection against master keys, drilling, folding;

disk. At least 10 code disks. Availability of protection against drilling and folding;

electromagnetic with pull-off force - 350 kg.

The cross-section of the bolt of mechanical locks is at least 300 mm 2, the length of the head is at least 40 mm. The bolt material is steel.

3.2. Padlocks:

pin. The number of code pins is at least 6. The design of the deadbolt is horizontal. The diameter of the bolt is at least 12 mm. Availability of protection against master keys, sawing of the bolt and knocking down the lock;

disk. The number of code disks is at least 10. The design of the bolt is horizontal. The diameter of the bolt is at least 12 mm. The presence of protection against sawing the bolt and knocking down the lock.

3.3. Garage locks - disc locks and level locks. At least 6 code discs and levers. The presence of protection against drilling and folding. The bolt material is steel. The cross section of the bolt is at least 750 mm 2. The overhang of the bolt is at least 40 mm, the length of the bolt head is at least 80 mm. The thickness of the body sheet is at least 2.5 mm.

4. Locking devices of 4 protection classes(very high or special degree of protection of the object from penetration).

4.1. Mortise and rim locks:

4 classes according to GOST 5089-97;

safe according to GOST R 51053-97, the number and class of locks is selected depending on the stability class of the door;

electromagnetic with pull-off force - 500 kg.

4.2. Padlocks:

pin. The number of code pins is at least 6. The design of the deadbolt is horizontal. The diameter of the bolt is at least 12 mm. The presence of protection against master keys, sawing of the bolt and knocking down the lock. Availability of protection against drilling of the secrecy mechanism and sawing of hinges;

disk. The number of code disks is at least 10. The design of the bolt is horizontal. The diameter of the bolt is at least 12 mm. The presence of protection against sawing the bolt and knocking down the lock. The presence of protection against drilling of the secrecy mechanism and sawing of hinges.

4.3. Garage locks- disc and level locks. At least 8 code discs and levers. The presence of protection against drilling and folding. The bolt material is steel. The cross section of the bolt is at least 1000 mm 2. The overhang of the bolt is at least 40 mm, the length of the bolt head is at least 100 mm. The thickness of the body sheet is at least 3 mm.

APPENDIX No. 10.

CHARACTERISTICS OF SECURITY TELEVISION EQUIPMENT

Table A10.1 - Main characteristics of television cameras

Table A10.2 - Main characteristics of video storage devices

Table A10.3 - Main characteristics of control and switching devices

Table A10.4 - Main characteristics of video monitors

Table A10.5 - Maximum video transmission range over coaxial cable in meters

Notes:

1. Tables P10.1 - P10.4 indicate the minimum requirements for CCTV devices. Depending on the characteristics of the protected object and the requirements for target recognition, these characteristics can be specified.

2. To transmit a video signal over distances exceeding those specified in Table A10.5, video signal corrector amplifiers or alternative ways video signal transmission (over twisted pair, over fiber optic lines, over telephone lines, radio and other channels).

Polymer-bitumen tape “LITKOR-NK-GAZ” is intended in the coating design as a wrapper when carried out in highway conditions overhaul insulation coating (re-insulation) of gas pipelines with a diameter of up to 820 mm inclusive, at a temperature of the transported product not exceeding +35 C.

Tape thickness: 1.8mm

Roll length: no less than 30m

The area of ​​the tape in a roll with a width of 450mm is 13.5 sq. m

Weight 1 sq.m. = 1.74kg

It is used in the following anti-corrosion systems (structures): Design No. 1. For pipelines with a diameter of up to 820 mm inclusive: 1. polymer butymic (mastic) primer Transkor;2. Litkor-NK tape (1 layer); 3. wrapping film PEKOM. Design No. 2. For pipelines with a diameter up to 1220 mm inclusive: 1. polymer butymic (mastic) primer Transkor;2. Litkor-NK tape (2 layers); 3. Polylen-OB wrapper.

Tape thickness: 1.8mm

Roll length: 360m

The area of ​​the tape in a roll with a width of 450mm is 13.5 square meters. m

Weight 1 sq.m. = 1.74kg

LITKOR tape L, Z, NNTU 2245-001-48312016-01

It is used in the following anti-corrosion systems (structures): Design No. 1.1. Polymer-bitumen primer TRANSKOR;2. Polymer-bitumen tape LITKOR in two layers;3. Protective polymer sticky wrap with a thickness of at least 0.6 mm. Design No. 2.1. Bitumen primer 2. Polymer-bitumen tape LITKOR in two layers;3. Protective polymer sticky wrapper with a thickness of at least 0.6 mm.

Tape thickness: no less than 1.5; 2.0mm

Length of tape per roll: no less than 30m

The area of ​​the tape in a roll with a width of 450mm is 13.5 square meters. m.

Weight 1 sq.m. = 2.2 kg

There are three types of Litkor tape:L - SummerZ - WinterNN - All-season

Ribbon polymer-bitumen LITKOR based on TRANSKOR mastic, it is intended for self-protection against corrosion of steel underground oil and gas pipelines, as well as product pipelines and water pipelines with the temperature of the transported product up to plus 40°C in protective coating designs No. 18 and 21 according to GOST R 51164-98, No. 5 and 6 according to GOST R 9.602-2005. PVC tape without an adhesive layer is used as a base tape. Depending on the formulation of the polymer-bitumen mastic, the tape is made in two types: summer, winter and all-season.

TU 2245-001-48312016-01

The tape is intended for insulating pipes with a diameter of up to 1420 mm inclusive and must have a mastic layer thickness of at least 1.1 and 1.6 mm, and a total thickness of at least 1.5 and 2.0 mm.

The tape is available in rolls of various widths for ease of use on pipelines of various diameters.

The tape is used in a set (design No. 18 VUS) with TRANSKOR primer or PL-M primer and mandatory protection of the coating with polymer wrappers of the POLYLEN-OB type. LITKOR polymer bitumen tape is used to insulate steel pipelines in urban networks. Buy VUS pipes design No. 18 ready for use in polymer bitumen insulation Litkor.

MAIN CHARACTERISTICS

Anti-corrosion polymer-asmol tape LIAM, GOST R 52602-2006 instead of TU 2257-016-16802026-99 with amendment. No. 1 . The tape is a polymer tape with a mastic layer based on Asmol applied to it. Polyvinyl chloride or polyolefin tapes are used as the tape base. To prevent sticking of the mastic layer in the roll, a release agent is applied over the mastic layer.

LIAM tape is available in the following brands:

LIAM-L tape (summer) for application to the pipeline at ambient temperatures from plus 5 °C to plus 30 °C, LIAM-Z tape (winter) - at temperatures from minus 20 °C to plus 10 °C. To insulate sections of pipelines with a temperature of the pumped product up to + 70 °C, LIAM (heat-resistant) tape is produced upon customer request.

LIAM tape is produced in accordance with GOST R 52602-2006 “Anti-corrosion polymer-asmol tape LIAM. Technical conditions".

LIAM tape is available in widths of 450, 225, 150, 112 and 90 mm. Delivered to the track in rolls.

The LIAM tape is certified by the Sanitary and Epidemiological Supervision authorities of the Russian Federation and has a hygienic certificate No. 2.BTs.01.225.P.001041.10.06 dated 10/06/2006.

Some physical and mechanical characteristics of LIAM tape:

Coverings based on LIAM tape are included as recommended in GOST 9.602 and belong to the reinforced type of insulation. Cover design:

Asmol primer, TU 2312-021-16802026-2000

LIAM tape in 1 layer

Polymer adhesive wrap with a thickness of at least 0.6 mm in 1 layer (for pipes with a diameter of no more than 114 mm) or 2 layers (for pipes with a diameter of up to 426 mm).

The adhesive layer of the tape ensures adhesion of the tape to the polymer layer, so LIAM tape can be applied over the previous layer without prior priming in several layers.

The tape application technology is as follows. Asmol primer is applied to the pipe surface, cleaned to the 4th degree, in a continuous, even layer. The use of other types of primers is not permitted! Then, using a non-dried primer, one layer of LIAM tape and a layer of polymer adhesive wrap are applied to the surface of the pipe.

LIAM tape should be applied to the surface with a mastic layer inward in a spiral without distortions, wrinkles, sagging, with an overlap of at least 30 cm, after unwinding the anti-adhesive from the surface of the tape.

Applying the tape to the surface of the pipe should be done using insulating machines or manual insulating machines of the “squirrel wheel” type.

Manual coating is only allowed for insulating short (up to 1 m) sections, inserts, bends and welding joints.

The use of LIAM tape does not require a high degree of cleaning of the pipe surface, as well as preheating of the pipe surface and insulating materials when applied in winter.

Theoretical consumption rate for insulating 1000 m of pipeline

coating based on LIAM tape

Coefficient K2 =1.05 (at manual application, as well as when changing the diameter of the roll, when the proper tension of the tape is not ensured, uneven overlap width, statistical variation in tape thickness, etc.)

Theoretical material consumption rates for insulating 1000 m of pipeline

1 roll of LIAM (calculated): roll weight - 54 kg, roll length - 50 m, LIAM tape thickness - 2.1 mm, weight 1 m2 ≈ 2.2 kg.

1 roll of Polylene-OB: weight 50 kg, length per roll 170 m (thickness - 0.6 mm)

1 roll of DRL-L tape: 0.8 mm - weight 41 kg. roll length 115 m / 1.2mm - weight 42 kg. length - 77 m.

Overlap 30 mm.

All tape consumption rates are given taking into account the coefficient for unaccounted losses. For manual insulation, material consumption rates increase by - 10%;

The product is approved for use at the facilities of OJSC Gazprom, certificate GO00.RU.1303.N00012

Note:

(a) rods - rolled, extruded, drawn or Forged Products, not rolled into coils and having a continuous cross-section throughout its entire length in the form of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons (including “flattened circles” and “modified rectangles”, the two opposite sides of which are convex arcs, and the other two sides are straight, equal in length and parallel). Products with a rectangular (including square), triangular or polygonal cross-section may have corners rounded along the entire length of the product. The thickness of such products having a rectangular (including “modified rectangular”) cross-section exceeds 0.1 of their width. This term also applies to cast or sintered products of the same shapes and sizes, subjected to processing after manufacture (other than simply trimming edges or removing scale), provided that they have not thereby acquired distinctive features, characteristic of products of other headings.

(b) profiles - rolled, extruded, drawn, forged or molded products, whether or not rolled into coils and having a constant cross-section throughout their entire length and not meeting the definitions of rods, wire, plates, sheets, strip or tape, foil, pipes or tubes The term also applies to cast or sintered products of the same shapes which have been subjected to treatment after manufacture (other than merely trimming or descaling), provided that they have not thereby acquired the distinctive characteristics of products of other headings.

(c) wire - rolled, extruded or drawn products in coils and having a continuous cross-section throughout their entire length in the form of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons (including “flattened circles” and “modified rectangles” ", the two opposite sides of which are convex arcs, and the other two sides are straight, equal in length and parallel). Products with a rectangular (including square), triangular or polygonal cross-section may have corners rounded along the entire length of the product. The thickness of such products having a rectangular (including “modified rectangular”) cross-section exceeds 0.1 of their width.

(d) plates, sheets, strips or strips and foil - flat products (other than unworked products of heading 76.01), whether or not rolled, and having a solid rectangular (other than square) cross-section, with or without rounded corners (including "modified" corners). rectangles", two opposite sides of which are convex arcs, and the other two sides are rectilinear, equal in length and parallel), with constant thickness, having:

– rectangular (including square) shape with a thickness not exceeding 0.1 width;

– a shape other than rectangular or square, of any size, provided that they have not acquired distinctive features characteristic of products of other headings.

Headings 76.06 and 76.07 cover, inter alia, plates, sheets, strips and foils having relief surface(for example, grooves, projections, cages, diamonds), as well as perforated, corrugated, polished or coated products, provided that they do not acquire distinctive features characteristic of products of other headings.

(e) pipes and tubes - hollow products, whether or not rolled into coils and having a constant cross-section with only one closed cavity along the entire length of the product in the form of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons and having constant wall thickness. Products with a cross-section in the shape of a rectangle (including a square), an equilateral triangle or a regular convex polygon, with rounded corners along their entire length, shall also be classified as pipes and tubes, provided that their internal and external cross-sections are concentric and of the same shape and orientation. Tubes and tubes having the above cross-sections may be polished, coated, bent, threaded, drilled, tapered, flared, tapered, or have flanges, collars, or rings at their ends.

Notes to subheadings:

1. The terms used in this group mean:

(a) unalloyed aluminum - a metal containing not less than 99% by weight of aluminum, provided that the content by weight of each of the other elements does not exceed the limits specified in the following table:

Other elements

(b) aluminum alloys – metal alloys, in which the content by mass of aluminum exceeds the content by mass of each of the other elements contained in the alloy, provided that:

(ii) general content other elements is more than 1 wt.%.

2. Notwithstanding the provisions of Note 1 (c) to this chapter, for the purposes of subheading 7616 91 the term "wire" means only products, whether or not coiled, and of any cross-sectional shape, the size of which does not exceed 6 mm.

Additional note:

1. In subheading 7601 20 200, the following terms mean:

– “slabs” - unprocessed products having a continuous cross-section throughout their entire length in the form of rectangles or other polygons, a width of more than 800 mm, a thickness of more than 280 mm and a length that always exceeds the width and thickness. These products are designed for rolling;

– “billets” – unprocessed products having a continuous cross-section in the shape of circles (including “flattened circles”), with a diameter of more than 125 mm, that is constant along the entire length. These products are designed for extrusion.

Additional note from the Eurasian Economic Union:

1. In subheading 7606 12 200 2, the term “multi-layer panels” means flat multilayer material, consisting of two outer coated aluminum sheets and one or more layers of filler forming an inner layer or core.

4 Selecting a fencing protection class depending on the category of the protected object

4.1. Depending on the functional purpose protected object and the expected threat during its operation, the significance and concentration of material, artistic, historical and cultural values ​​located at the object, the consequences of possible criminal threats to them, all objects, their premises and territories are divided into categories.

4.2. In accordance with RD 78.36.003-2002 “Engineering and technical strength. Technical means security Requirements and design standards for the protection of objects from criminal attacks”, approved by the Minister of Internal Affairs Russian Federation November 6, 2002, objects and territories protected using perimeter fencing are divided into two groups (categories): A and B. Due to the large variety of heterogeneous objects in each group, they are further divided into two subgroups each: AI and AII, BI and BII:

objects AI and AII categories(AI category - the highest) - these are objects of particular importance, increased danger and life support, illegal actions (theft, robbery, robbery, terrorism and others) on which, in accordance with the criminal legislation of the Russian Federation, can lead to large, especially large economic or social damage to the state, society, enterprise, environment or other property owner;

objects of BI and BII categories- these are objects where theft, in accordance with the criminal legislation of the Russian Federation, can lead to damage in the amount of up to 500 times the minimum wage and over 500, respectively.

4.3. In accordance with the “Instructions for ensuring engineering and technical strengthening and increasing the level of anti-terrorist protection of objects of internal affairs bodies of the Russian Federation from criminal attacks”, approved by order of the Ministry of Internal Affairs of Russia dated January 18, 2011 No. 24, as amended by order of the Ministry of Internal Affairs of Russia dated 1 June 2013 No. 337, objects and territories protected using perimeter fencing are divided into:

objects of category I– a complex of buildings or structures that have a common adjacent territory (or without it) and external boundaries; a separate building or structure with an adjacent territory (or without it), where 24-hour access control and 24-hour duty are mandatory;

objects of III category– separate buildings or structures with an adjacent territory (or without it), where 24-hour access control and 24-hour duty are not necessary.

Protection class 1 fencing (the minimum required degree of protection of an object from penetration) - the main fence with a visible flexible or rigid sheet made of steel rods with a diameter of 4 - 5 mm, welded at the intersections, with a cell no more than 50x200 mm, galvanized and coated polymer material, or fencing made of various structural materials.

Protection class 2 fencing (average degree of protection of the object from penetration) - a main fence that has a sectional visible metal mesh or rigid lattice fabric, made of steel rods with a diameter of 6 mm, welded at intersections, with a cell no more than 50x200 mm, galvanized and coated with a polymer material.

It is allowed to use a solid wooden fence made of boards with a thickness of at least 40 mm.

Protection class 3 fencing (high degree of protection of the object from penetration) - the main fence having a sectional visible rigid metal mesh sheet, made of galvanized expanded metal sheet with a thickness of at least 2 mm or steel rods with a diameter of 6 mm, welded at the intersections and reinforced with a double horizontal rod with a cell no more than 50x200 mm or fences with a rod diameter of 5 mm with a cell of 25x100 mm, galvanized and coated with polymer material.

The main fence can be installed on a strip reinforced concrete foundation with a height above ground level of at least 0.5 m or on a pile foundation.

When installed on a pile foundation, the main fence must be equipped with an additional lower fence.

If necessary (specified in the inspection report, technical specifications for design), in accordance with the architectural and structural solutions of these territories, it is allowed to use the following fence as the main fence:

Reinforced concrete, at least 100 mm thick,

Stone or brick, at least 250 mm thick,

Solid metal with a sheet thickness of at least 2 mm, reinforced with stiffeners, mounted on a strip reinforced concrete foundation height above the ground level of at least 0.5 m, with a depth into the ground of at least 0.5 m.

Protection class 4 fencing (special degree of protection of the object from penetration) - the main fence made of galvanized expanded metal sheet with a thickness of at least 2 mm, or from a rigid metal mesh fabric with a diameter of vertical rods of 6 mm, welded at the intersections and reinforced with a double horizontal rod with a diameter of 8 mm, with a cell no more than 50x200 mm, galvanized and coated with polymer material. The fence is installed on a strip reinforced concrete foundation with a height above ground level of at least 0.5 m.

The main guard must be equipped with an additional lower guard.

The main fence must be equipped with additional top and warning guards.

To prevent vehicles from breaking into the protected area, anti-ram barriers must be installed.

If necessary (specified in the inspection report, technical specifications for design), in accordance with the architectural and structural solutions of the given territory, it is allowed to use fences as the main fence:

Monolithic reinforced concrete with a thickness of at least 120 mm,

Stone or brick with a thickness of at least 380 mm.

Or the decorative fencing option described in clause 11.2.1. “Instructions for providing engineering technical strength and increasing the level of anti-terrorist protection of the objects of the internal affairs bodies of the Russian Federation from criminal attacks.”

4.5. Depending on the magnitude of possible social or economic damage to the state, society, enterprise, environment or property owner, as well as the implementation of a mandatory round-the-clock access regime and round-the-clock duty at the site, for each category of security objects the number of perimeter fencing lines is determined, and the fences themselves must comply with a certain class (degree) of protection of structural elements.

4.6. The number of perimeter fencing lines, with the help of which the required protection class of the protected object is achieved, is determined in accordance with Table 4.1 of these guidelines.

Table 4.1 Correspondence of object categories to protection classes and number of fencing lines.

* According to design specifications.

4.7. Regardless of the category of the object, if there is no possibility due to objective factors, it is allowed not to use at all or to use the main fence of a lower protection class.

To such objective factors relate:

Location of buildings and structures of the facility in close proximity to transport routes(there is actually no territory in front of the façade of the protected building);

Construction or reconstruction of a facility in special climatic zones(permafrost, deserts, forests, etc.);

Significant length of the perimeter of the protected area;

The main fencing does not meet the required protection class regulations authorities of constituent entities of the Russian Federation or municipal authorities in terms of architectural and planning decisions for the development of a region, region, city.

In this case, ensuring the necessary security of the facility is achieved by creating additional security lines, organized with the help of a physical protection system consisting of personnel on duty shift for the security of the facility, organizational and technical measures and actions carried out by them, as well as a set of engineering and technical security means.