Self-leveling floor Weber Vetonit fast level characteristics. Quick-hardening self-leveling floor: instructions for use. Positive technical characteristics of Weber-Vetonit fast level self-leveling floor

(weber.vetonit fast level)

PURPOSE

• For leveling foundations in residential, public, office premises
• Used in repairs and new construction on concrete, cement-sand, gypsum bases, as well as on weak (strength less than 10 MPa) and complex bases, provided that a “floating floor” is created
• Can be used as a base under any, even thin, floor coverings
• Suitable for electrically heated floors
• For interior works in dry rooms
• For manual and mechanized application

ADVANTAGES

• Hardens quickly and gains strength - styling finishing coating possible in a day!
• Self-leveling, spreads well, does not require professional skills to use
• Wide range of layer thickness - from 2 to 60 mm in one pass!
• Ideal for most finishing coatings - parquet, laminate, linoleum, tiles.
• Applicable on weak grounds, c. incl. GKL, GVL, wooden bases subject to the creation of a "floating floor"

SPECIFICATIONS

INSTRUCTIONS FOR USE

Preparing the base

The building must have a roof. Window and door openings are closed. During work and for at least 1 week after completion, the temperature of the air and the base surface should be within +10...+25⁰С. During work and in the first 24 hours, avoid exposure to drafts and air drafts on the floor surface. The base must be dry, hard and dust-free. Suitable base under weber . vetonit fast level is concrete or cement-sand screed (“age” ≥1 month) with a compressive strength above 10 MPa. Can be used on complex and weak (with compressive strength less than 10 MPa) bases, provided that a “floating floor” is created.

Clean the surface from grease, cement/carpet adhesive, oil stains and other contaminants. Remove loose areas and weak top layer of concrete by grinding or milling. Seal any holes in the base and areas of possible mortar leaks; Separate the location of the drain wells with a special stopper. Significant depressions and irregularities (>60 mm) are recommended to be pre-leveled with material weber.vetonit 5000 or weber . vetonit 6000 .

To improve the adhesion strength of the material to the base, vacuum and prime the surface with an aqueous dispersion solution weber.vetonit MD 16, diluted in accordance with the instructions on the package, or with a universal primer weber.prim multi. Apply 2 layers to dry and highly absorbent bases. If leveling is carried out in several layers, it must be remembered that the base is treated with a primer before each leveling layer, and the previous leveling layer must be completely dry to ensure normal absorption of the primer into the base.

Priming the surface increases the spreadability of the solution and prevents the formation air bubbles and too rapid absorption of water from the solution into the base.

Preparation of the solution

Bag (25kg) of dry mixture weber.vetonit fast level pour into a container with 6.25 l clean water(25% by weight of the dry mixture). If necessary, to increase spreadability, you can add no more than 0.5 liters of clean water. Mixing is done with a drill with an attachment for 1 minute. The prepared solution can be used within 30 minutes from the moment of mixing with water.

The temperature of the working solution and base should be in the range from +10 to +25⁰С. In cold conditions, it is recommended to use warm water (t ≤+35⁰С). Do not overdose on water! Excess water leads to delamination of the solution, weakens the strength of the floor, slows down the drying process and is one of the reasons for the formation of cracks.

When mechanized floor pouring, dry mixture weber.vetonit fast level pour into the hopper of a mortar mixing machine (M-tec, Putzmeister) and, by adjusting the water flow, select the required consistency of the solution. Before pouring and periodically during work, the spreadability of the working solution should be monitored (190-220 mm for a spreading ring d=68 mm, h=35 mm).

Execution of work

It is recommended to fill the floor in strips 30-40 cm wide, starting from the corner of the room and excluding breaks in work. The prepared solution is poured onto the prepared base so that the layer thickness is in the range from 2 to 60 mm. To speed up spreading, the mixture is distributed over the surface using a smooth steel spatula and leveled with a needle roller, the length of the needles is 3 times greater than the maximum layer of application of the solution.

Leveling work separate room should be done without interruptions to avoid overflow. When pouring floors over large areas, the base should be temporarily divided into sections using limiters.

The leveled surface is suitable for walking after 3-4 hours (at air temperature - +20˚С). The next layer (if necessary) can be poured after 24 hours. The material reaches its nominal strength by 28 days. High moisture content in the base and low temperature indoors slow down the drying process of the material, low humidity And heat reduce the time it takes to set.

When creating a “floating” screed, the leveling layer weber.vetonit fast level It is recommended to additionally reinforce with fiberglass mesh weber.vetonit R108, having previously secured the mesh to the base to prevent it from floating. Layer thickness weber.vetonit fast level in this case it will be at least 25 mm.

Floor coverings

Waterproofing can be laid on a leveled surface weber.tec 822 (Superflex 1) in accordance with the instructions for this material, as well as various floor coverings. Ceramic/stone tiles can be laid directly onto the finished floor within 1-7 days depending on thickness. Laying linoleum, carpet, laminate, parquet board, vinyl tiles, cork and parquet can be produced in 2-21 days (depending on the thickness of the layer and drying conditions). Under piece parquet, glued to the base, it is necessary to lay plywood due to the presence of moisture stress in the wood. All work on laying floor coverings is recommended to be carried out in accordance with the recommendations of the floor covering manufacturer (with mandatory monitoring of permissible base moisture levels).

Table 1. Readiness for laying floor coverings (days), not less than:

Attention! It is not recommended to paint the leveled surface and leave it without floor covering.

CLEANING THE INSTRUMENT

Working tools and equipment are washed with water immediately after completion of work.

PRECAUTIONARY MEASURES

When working, you must use rubber gloves; avoid contact with skin and eyes; If the mixture gets into your eyes, rinse big amount water; keep away from children.

DISPOSAL INSTRUCTIONS

The dry mixture and hardened material must be disposed of as construction waste.
The material must not be discharged into the sewer. Dispose of the paper bag as regular waste.

Quick-hardening self-leveling floor Weber-Vetonit Fast Level is a high-quality and fast-hardening self-leveling floor, which becomes even and smooth after drying. It should be noted that this brand finishing materials for horizontal surfaces is different increased strength, long service life and reasonable price.

Sale of Weber-Vetonit Fast Level with delivery in Moscow

You can buy Weber-Vetonit Fast Level in our online store at affordable price, or wholesale. Also, each client can order an order delivery service; the goods will be delivered to the specified address in a short time.

Reinforcement of internal type. Special fibers significantly increase bending strength, and also provide resistance to cracks and long-term use of the floor, which allows the material to be used on all screeds. When applied material mechanized type small layers ranging in size from three to sixty millimeters are used. Thus, the productivity of finishing work increases significantly.

Positive technical characteristics of Weber-Vetonit fast level self-leveling floor

• Hardens quickly.
• Fast drying time, which significantly speeds up finishing and repair work.
• A wide range of application thicknesses from three to sixty millimeters allows for all finishing and construction works one product means the versatility of the product.
• For unstable work surfaces, which is not typical for everyone finishing materials for horizontal surfaces.
• For the system heated floors.
• Elasticity.
• Resistance to cracking.

It should be noted that the original is presented in our online store weber vetonit fast level 20 kg. The price of the material is affordable; if necessary, the client can use delivery of the order. Registration and delivery of building materials is carried out in a short time.

An ideal interior is impossible without quality repairs, and the first quality indicator is smooth surfaces walls, ceilings and, of course, floors. Any person who decides to make repairs or decorate a new apartment on their own faces the problem of leveling floors.

Tip 1. Choose quality materials and strictly follow the instructions on the package!

No matter how banal this advice may sound, it is always relevant. The choice of materials for pouring your future floor is perhaps the most important thing. initial stage. Particularly good are modern dry mixtures produced using modifying agents. polymer additives European quality. For example, weber.vetonit fast level is a quick-hardening self-leveling floor that can be used both for leveling during repairs and for filling the floor when finishing a new room. Such mixtures have many advantages over Russian analogues of a lower price segment.

In order to make the perfect floor for your apartment or office yourself, you don’t have to be a qualified repair worker with extensive experience - just read enough simple instructions on the packaging, carry out the necessary preparatory work and start pouring the floor. It is important to follow all stages of work exactly!

Stage 1: preparatory work

Preparatory work begins with cleaning the floor surface from dust and dirt, remnants of old glue or coating, loose particles old screed. It is best to start with dry cleaning with a vacuum cleaner, then you can go over the floor with a slightly damp cloth to finally remove any remaining dirt.

After this it is necessary check the floor for any holes. They must be repaired using a suitable repair compound, e.g. weber.vetonit S06, otherwise, when leveling the floor, the solution will flow out, and, therefore, when the solution hardens, you will not get the expected result.

Next the most important stage preparing the base is priming the surface. At the same time, the absorbency of the surface is leveled, the spreadability of the poured floor and its adhesion to the base increase. In 80% of 100% cases, this is the key to obtaining a strong screed without peeling or cracking!

To solve this issue, it is best to use a special ultra-economical primer-concentrate weber.vetonit MD 16. So to treat 10 m² you will need only 1 liter of concentrate (priming in 2 layers, dilution proportions soil: water: 1st layer - 1:5, 2nd layer - 1:3).

Next we act according to the instructions! To prepare the solution, you will need a large container and a drill mixer with a special mixing attachment. According to the instructions on the package, pour a precisely measured amount of water into the container, add the dry mixture and mix with a drill mixer for 1-2 minutes until a homogeneous consistency without lumps is obtained.

Important: weber.vetonit fast level l mixture is suitable for leveling concrete, cement-sand, gypsum surfaces, as well as for weak foundations with a compressive strength of at least 10 MPa. This mixture is also suitable for creating “warm floors” in the bathroom and kitchen.

Stage 2: pouring the floor

Before you start pouring the floor, make sure once again that you have prepared the solution correctly according to the instructions.

The working time with the ready-made self-leveling floor solution is quite limited - literally 20-30 minutes after pouring, so you need to act quickly and carefully: pour it onto the base, level it to the required thickness, and, if necessary, level it with a needle roller.
The material must be applied in small portions, each of which must be in contact with the previous one.

Next, the material will “act” for you: it will “take on the horizon” itself, creating a perfectly flat floor, and all you have to do is wait. In the case of the weber.vetonit fast level mixture, you will only have to wait a day before laying the floor covering (of course, depending on the fill layer), while domestic analogues can take up to two weeks to dry! The solution spreads well, which greatly facilitates the process of applying the material, eliminating the formation of sagging on the surface of your future floor.

If the differences in height of the treated surface before applying the solution were quite noticeable, then it is best to apply another leveling layer after the previous one has completely dried (in the case of weber.vetonit fast level - no earlier than 24 hours after applying the first layer).

Not all rooms can boast of a perfectly flat floor. Many companies that manufacture Construction Materials, offer special compounds for self-leveling the surface. One of the leaders in the repair business is the Weber company, which has been famous for its products for more than 25 years. Vetonit self-leveling floor allows you to cope on your own and remove possible differences in the floor surface, moreover, use the product as a screed.

Specifications

You can prepare and pour the mixture without the use of specialized equipment. Everything is diluted in accordance with the instructions. The mixture consists mainly of cement and various additives. The solutions have excellent adhesive properties, and the maximum shrinkage is only half a millimeter. 20 kg bags have an average consumption of 12 sq.m. The composition is completely environmentally friendly. The finished floor is resistant to moisture and fire. Whether it's the floor in a room, office or bathroom - you will be satisfied. The main thing is not to neglect operational requirements. Let's look at the most popular products in the Vetonit line.

Superfinish self-leveling floor Vetonit 3000 is a dry mixture based on cement and fine marble. It is used to level the floor covering with a layer of 0-0.5 cm and local repair of cracks up to 1 cm deep. Applied to concrete or sand-cement base, which has been previously cleaned of all kinds of contaminants. It is afraid of drafts, so it can only be used indoors with normal and increased level humidity. Apply manually, using available means at air temperatures from +10 to +25 °C. The mixture has good adhesion.

Finishing Weber Vetonit 3000 for heated floors

The manufacturer recommends using Vetonit 3000 as a stable base for subsequent laying of the finished floor, but not as an independent unit. The consumption of Vetonit 3000 self-leveling floor is 1.5 kg of solution per 1 sq.m, provided that the layer does not exceed 1 mm.

Important! It dries very quickly - this is the main problem discussed on the forums. Experienced builders advise dividing the area into zones, because the solution hardens after half an hour. And if the area is large, it is better to take someone to help, since you will have to knead a new batch every 20 minutes.

Subsequent manipulations for laying the floor can be carried out after 24-72 hours - depending on the thickness of the differences that were covered by the self-leveling Vetonit 3000.

Main parameters:

The price of the bag is 570 rubles.

Pros of the composition:

• Vetonit 3000 is suitable for laying heated floors;
• for rooms with high humidity levels;
• premises for any purpose;
• quick drying.

• adding more than the required volume of water will lead to cracking of the floor;
• working with it is not easy, the alignment procedure requires special skill, you need to move extremely quickly;
• quick drying does not allow working on large areas;
• Suitable only for surfaces that do not have large differences, maximum 3 mm;
• not suitable for use over gypsum substrates.

Weber Vetonit 3100 is a modernized new product that is used as a finishing, filling, leveling agent. Excludes any coatings other than concrete. It can also be used to seal cracks. Pre-vacuum the surface from dust and remove grease. Floors should be primed in two layers. Begin installation in a hermetically sealed manner indoors- three days after the flood, this norm should be observed. If there is a need to level the floor in several stages, after each layer has dried, it will need to be primed again. And fill only after 24 hours.

Vetonit 3100 for moderate load (houses, public buildings)

Self-leveling self-leveling floor Vetonit 3100 is suitable for use in rooms with moderate load, including residential and public. Depending on what you will use as floor covering, you should wait from 3 to 7 days.

The solution is prepared in the proportion of 4.8-5.2 liters of water per 20 kg or 240-260 g per 1 kg of mixture.

Main parameters:

Price from 460 rub.

Pros of the composition:

• good spreadability;
• possibility of layering.

• you can only work in warm rooms;
• You can't walk around until it's completely dry.

Self-leveling floor Weber Vetonit 5000 - basic leveler

Self-leveling floor Vetonit 5000 is a basic leveler that is used as initial leveling. Suitable for use in premises of any purpose. Recommended application of a layer is from 0.5-5 cm. The room should be warm and dry, have a temperature from +10° to +25°C. To dilute a solution from a 25 kg bag, you will need 3-3.5 liters of water. The resulting thick mass remains plastic for half an hour. Can be applied in several stages.

Weber Vetonit 5000

Maintain an interval of 1-3 days, depending on the thickness of the layer. If you plan to use Vetonit 5000 dry mixtures for self-leveling floors as a monolithic screed, you will need to install and attach a damper side strip at the junction of the walls and the floor to reduce noise and free deformation of the screed.

Main parameters:

Cost 590 rub.

• monolithic screed;
• withstands dynamic loads;
• moisture resistance.

• price;
• fast setting;
• high consumption.

Vetonit 4000 self-leveling floor is a universal self-leveling floor with a mineral binder in its composition. Can be used as a topcoat and screed. It is laid in a layer from 3 mm to 8 cm in one pass. It is better to carry out thick screeds using beacon slats, leveling the layer with a control slat.

WEBER VETONIT 4100 for screed and finishing

The use of primers containing quartz sand is prohibited. Kneading is done manually using a drill with a mixing attachment, or using an m-tec machine. The manufacturer recommends conducting a spreadability test. It is advisable to fill the floor within +15/+25°C. The surface is ready for subsequent laying of floor coverings through:

Main parameters:

Price from 400 rub.

• tiles can be laid the next day;
• drying speed.

• cannot be primed with concrete contact.

High-strength self-leveling floor Weber Vetonit 4100 is a high-strength self-leveling floor that is highly resistant to cracking. He shows good adhesion on concrete and cement-sand bases.

Weber Vetonit 4310

The Vetonit 4310 self-leveling floor loses its plasticity a little earlier than the others - 20 minutes, and the consumption when applying 1 mm of thickness is 1.6 kg/sq.m. To mix the solution with one bag, you will need 4.8 liters of water. Layering is allowed after 24 hours. Good basis for floors with electric heating.

Main parameters:

Price 520 rub.

• easy mixing of layers;
• fast hardening.

• The consumption indicated on the packaging does not always correspond to reality;
• price.

Vetonit Fast Level is a quick-hardening self-leveling floor for houses, apartments and public premises. Withstands moderate loads. Unlike previous configurations, the viability and fluidity of the Vetonit Fast solution is as much as 40 minutes. Besides concrete foundations, also used on gypsum coatings. Primers with quartz sand are not allowed for use.

Weber Vetonit Fast Level

Specifications:

Flooring can be laid after just 1 day if minimum thickness layer and after 21 - at maximum. Price 325 rub.

• ceramic tiles can be laid directly on the floor;
• Suitable as a screed for heated floors.

• turns black after drying;
• dries very quickly, only for small spaces.

Vetonit Strong has this name for a reason. This is due to the fact that it is used with reinforced mesh. It is applied for various types screeds: monolithic, on a separating layer, floating with sound/thermal insulation. Can be poured over unstable or dilapidated surfaces and even wooden floors.

The layer filling ranges from 1 to 5 cm and depends on the differences. Foot traffic when screeding can occur within 6-8 hours. The manufacturer advises not to carry out the installation yourself, but to invite a work team consisting of at least 3 people.

Specifications:

Floor coverings can be laid after at least 1 week. It is better if this period is 3 weeks. Price 398 rub.

• possibility of use as a reinforced screed;
• small shrinkage.

• the complexity of creating a screed.

Which Weber self-leveling floor to choose and how to install it correctly

The choice is made depending on your needs and subsequent goals. If you just want to level the floors, Vetonit 3000 self-leveling floor or Fast Level, a quick-hardening mixture, is quite suitable. A universal soldier, also suitable for screeding, is Vetonit 4000 and Vetonit Strong.

The required number of bags for a specific area can be easily calculated using the calculator installed on the official Weber website. The company is active in information activities on the Internet, and always puts emphasis on the technology of mixing the dry mixture with water:

• Pour only the amount of water indicated in the proportions on the package. Do not increase the fluidity of the mixture by adding liquid in excess;
• check the container for the accuracy of the indicated volume, a fluctuation of even 200 g can lead to delamination, prolonged drying and the appearance of cracks;
• It is not recommended to dilute by hand; it is better to use a drill with a mixing attachment, or a special machine.

Installation should be carried out in accordance with the manufacturer's requirements:

• this is always a room with a roof;
• any draft is excluded;
• even after pouring, over the next 3-7 days the room is deprived of ventilation;
• base and air temperature from +15°C to +25°C;
• the water is clean;
• all instruments are dry and clean;
• the prepared surface is completely cleaned of dust, moisture and oil stains;
• all flaws and cracks are covered or filled with Vetonit.

VIDEO: How to work with self-leveling floors - technology from A to Z