Technical characteristics of various types of ursa insulation (ursa). Technical characteristics of various types of insulation Ursa (ursa) Ursa p 15 technical characteristics

These simple rules will help to carry out high-quality work on insulation and soundproofing of premises and will allow you to avoid many mistakes when working with URSA GEO materials.

Shipping

When transporting URSA GEO, protect the material from rain, snow and possible damage. When loading into a car or van, do not squeeze the material packages. Also, do not over-tighten the material with fastening ropes and other transport devices. This is due to the fact that the material in the package is already in a compressed state, and additional compression can lead to a deterioration in the recoverability of its thickness. Place packages with slabs horizontally in the car body. When carrying material in a roll or bundle, it is not recommended to grasp the material by the open edge of the package at the end. This may cause premature damage to the packaging.

Storage

Protect when storing URSA material GEO from exposure to precipitation. Store the material in packaged form in covered, dry rooms or under a canopy. When storing outdoors under cover, do not place packages on the ground, but place them on pallets. Place packages with slabs in a horizontal position, install rolls vertically (up to 3 tiers inclusive).

Unpacking

Remove material from packaging immediately before use on site. This will significantly reduce the risk of damage to the material. The packaging can be used to protect the material from contamination when laying out on a construction site or as collection bags construction waste.

When unpacking mats (rolls):

Open the package by cutting it sharp knife(it is recommended to start cutting from the edge of the roll, having first made two cuts to the film at the end).

Roll out thermal insulation mats the entire length.

Wait 5-10 minutes or lightly shake the rolled sheet: the material should restore its nominal thickness.

Some URSA GEO mats are supplied with 2 products per package, for example, URSA GEO M-11 (2x50 mm). In this case, if you need to use 50 mm thick material, the mats must be separated from each other after unpacking. When unpacking the slabs, simply open the packaging.

Installation

When working with the material, it is recommended to wear gloves and protective clothing; It is also recommended to wear safety glasses when placing material overhead. These safety requirements are the same for everyone mineral wool insulation(fiberglass, stone wool, slag wool) and serve mainly to protect against dust arising when working with the material. Use a sharp, long knife to cut the material on a hard surface. Do not use dull knives, as this can lead to “pulling out” of the fibers of the material and reducing its quality.

When installing materials into the structure, follow the recommendations indicated on our website or the manufacturers' recommendations thermal insulation systems. Use only URSA GEO grades recommended for the specific application.

The standard thickness of many URSA GEO materials is 50 mm. In this case, the required thickness of thermal insulation in the structure can be 100, 150 or 200 mm. To obtain the required thickness, lay the material in several layers. For example, to obtain a thickness of 150 mm, you can lay 50 mm thick material in 3 layers. You can find out what thickness of thermal insulation is needed using our calculator.

When installing, place insulating materials tightly to each other and to the base. When laying slabs in several layers, it is recommended to place the joints of the slabs with an overlap - so that the slab of the next layer overlaps the joint of the slabs of the previous layer by at least 10 cm. This will avoid through gaps and “cold bridges”. When installed in a frame, the width of the material should be 1-2 cm greater than the clear distance between the frame elements. The material is then held in frame structure due to the elastic thrust forces that arise during compression of the fiberglass.

Final work

After completing work and before removing waste material, spray the work area with water. This will reduce the dust content in the air during cleaning. Cleaning is best done using a vacuum cleaner. To collect waste material and other construction waste, you can use the packaging left over from the insulation.

Ursa P 15 insulation is elastic and lightweight material for professional thermal insulation of building structures. It is produced in the form of slabs of fairly large sizes. Special Ursa properties GLASSWOOL P-15(G) are provided with innovative fiberglass. First of all, it is intended for insulation of frame walls and various partitions in increments load-bearing elements up to 60 cm. However, the significant dimensions of Ursa P 15 are not a limitation for installation by one person - the material is light, perfectly processed and does not irritate the skin of the hands.

The advantages of Ursa GLASSWOOL P-15(G) slabs are obvious when compared with Ursa GLASSWOOL M-15(G) mats. Due to the increased dimensions of the slabs and the aspect ratio of 2:1, it is easier to achieve:

Reliable insulation of interface lines of building structures - for example, a sharp roof slope and façade wall at internal insulation attic space.

High-quality protection of hard-to-reach places with a heat-insulating layer without reducing its thickness, including at the junction of external and internal joints at right angles.

Ability to perform insulation work by one installer, including on inclined surfaces.

physical characteristics thermal insulation URSA P-15(G)

Specifications

• Walls based on a metal or wooden frame.
• All types of frame cladding of internal partitions.
• Walls and partitions made of sandwich panels.
• External walls with pre-insulation installed frame and with subsequent finishing of the facade with siding panels.
• Partitions of frame-sheathing type (for sound insulation).
• Multilayer walls made of stone blocks, bricks, etc. with the laying of insulating material in the middle (inner) layer.
• All types of acoustic ceilings.

It is acceptable to use Ursa GLASSWOOL M-15(G) insulation on the following objects:

• Loggias and balconies
• Pitched roofs with slabs installed under the rafters and between them.
• All types of roofs made of sandwich panels installed on a frame.
• Attics and interfloor ceilings beam type.
• Beam ceilings over unheated basements.
• Various industrial equipment, industrial air ducts.
• Walls and ceilings in baths, saunas and other rooms with high humidity.
• Railway, road and water vehicles.
• Prefabricated modular buildings.

At Stroymet you can always buy Ursa P15 insulation at favorable conditions- we have discounts and

Every second family thinks about insulating their home. Most of the houses were built back in Soviet times, where there were no affordable and effective insulation materials. In this regard, residents in winter period They are freezing in their house, but in the summer, on the contrary, they don’t know where to escape the heat. To eliminate this problem, you need to study the different types of insulation that exist on the market and choose the most suitable one. One of these types is Ursa insulation, which you can familiarize yourself with now.

Ursa insulation and its types

The manufacturer of this insulation is German Ursa company, several branches of the company are located in Russia. The insulation is mineral wool, which is based on durable stamped glass fiber. It can be used to insulate any part of the house structure. This insulation has soundproofing properties and resistance to mechanical loads. The company's specialists have developed several series of insulation.

The following can be distinguished kinds Ursa insulation, each of which has its own purpose:

• Ursa M 11 is a lightweight insulation made from fiberglass. The mats are soft, pleasant to the touch, elastic, environmentally friendly, and resistant to various vibrations. Anyone will be pleased with its price. But there are small disadvantages: they are not entirely durable and flexible. Yes, and when installing insulation M 11 should be used gloves and respirator to avoid small fiberglass particles getting on your body and preventing further unpleasant irritation.
• Ursa M 11 F is a roll that is covered on one side with a vapor barrier aluminum foil. This coating prevents the penetration of steam and prevents the formation of condensation. In this regard, it can be used indoors With high humidity and feel free to insulate places that come into contact with water. This room can be a bathhouse, sauna, attic, basement.
• Ursa M 15 has good elasticity and compressibility. Insulation is mainly used for insulating floors, pitched roofs, partitions.
• Ursa M 25 is a lightweight roll that offers good flexibility and thermal insulation. It can only be used indoors, it not suitable for use on outdoors, in pipes or in the ground. Insulation M 25 prevents heat loss in pipelines with a diameter of 32.5 cm. Capable of absorbing the sound of industrial units, for example, boilers and tanks. It would also be appropriate to use it on pitched, attic and mansard roofs, and plasterboard partitions.
• Ursa P 15- its main application is to insulate pitched roofs, frame walls and partitions. One person can handle the installation of this insulation. P 15 is a very light and, at the same time, elastic material.
• Ursa P 20 intended for insulation outer wall. The insulation is installed either outside or in the middle layer of the wall. P 20 has good heat and sound insulation.
• Ursa P 30 has high elasticity and flexibility, due to which the insulation is tightly mounted on the surface. Designed for use in air ducts and gas outlets (preferably rectangular shape), insulation of a pipeline with a large diameter.
• Ursa P 35 It is insulation in the form of plates. It is vapor-proof and resistant to various vibrations. Some slabs can be treated with fiberglass or a water repellent. You can find out about this as follows: in the first case, the letter C will be added to the brand of insulation, and in the second - the letter G. This insulation is mainly used on railway, water and road transport in order to maintain heat and suppress noise.
• Ursa P 60 intended for use under flooring(tiles, laminate, etc.). This insulation has very high sound-absorbing properties.
• Ursa Light- a fairly popular insulation material that is light, elastic, durable, non-flammable material. Besides he does not react on chemical exposure and changes in ambient temperature.
• Ursa Pitched Roof is a yellow mat that has sound and heat insulation and elasticity. When installing insulation, almost not formed waste.
• Ursa Facade covered with black fiberglass, which is very durable. It is used for insulating systems that have ventilated gaps. It has sound and heat insulation and holds its shape well.
• Ursa Partition used for installation on frame partitions. The insulation is light, elastic, noise-absorbing and heat-insulating.
• Ursa XPS used to protect the foundations of buildings and road construction.

Technical characteristics of URSA insulation

Ursa insulation has the following properties:

1. Fire safety, most of types of insulation are non-flammable.
2. Elasticity and flexibility, which allows the insulation to be laid more tightly to the surface.
3. Thermal insulation.
4. Soundproofing.
5. Resistant to loads, can even be used in road construction.
6. Ecologically safe product, which is confirmed by the certificate of conformity.
7. Easy to install. Installation is easy, simple, quick, and there is virtually no residue left at the end of the job.
8. Wide range of applications. It is used for insulation or soundproofing of partitions, external walls, pitched roofs.

More detailed characteristics for each series of insulation can be considered in the table:

Comparison of Ursa insulation

Of all the firms that are on the market, competitors Urs can be called:

• Rockwool - produces insulation from mineral wool, made in the form of mats and slabs. Its average cost is 450 - 600 rubles.
• Isomin- produce insulation materials consisting of basalt fibers. The price per package is about 340 rubles.
• Knauf- soft insulation is made from mineral wool or expanded polystyrene. Its cost is from 775 rubles.
• Park. It is very light and easy to work with. The cost is 900 - 1200 rubles.
• Ecowool- produce cellulose insulation. Their cost is 280 rubles per sq. m. meter or 1400 rubles per cubic meter. meter.

All these companies can be compared with each other according to density insulation. The densest are Ecowool and Ursa. Medium density have Rockwool and Isomin, and the least - Parok insulation. The next comparative property is the environmental friendliness of the insulation composition. The most safe are: Izomin, Ursa, Knauf, Rockwool and Ecowool. They do not rot, do not burn, do not emit harmful substances. You can also compare by possible area applications. If the insulation is light in weight, then it can be used to insulate a room from the inside - such are Parok and Krauf. Insulation with more heavy weight can be mounted on facades, these are: Rockwool, Ursa, Isomin.

Features of installation of Ursa insulation

Even a person far from the construction industry can install Ursa insulation. Installation is quite simple due to slabs and rolls of insulation, which have small sizes and good elasticity. The main thing is to prepare the surface well, because this insulation is mounted only on the base. They can serve as plywood or boards. The material is laid quite tightly to the surface itself; it should be fixed using self-tapping umbrella screws. If the calculation required quantity insulation will be produced Right, then at the end of the work there may be no residues.

Lightweight and elastic material intended for use in the structures of pitched roofs, partitions and frame walls with a pitch of load-bearing elements of 600 mm. The shape and geometric dimensions allow the installation of the slabs by one person.

The main difference between URSA GLASSWOOI P-15(G) slabs and URSA GLASSWOOI M-15(G) mats is the shape and dimensions, allowing:

• insulate internal and external joints of structures at angles close to right without reducing the thickness of the layer;
• ensure high-quality insulation of hard-to-reach places where structures meet, for example, the roof slope and wall when insulating from the inside of the room;
• carry out work on heat and sound insulation of inclined surfaces by one person.

Technical characteristics of URSA P-15(G)

Mineral heat and sound insulation based on fiberglass. Produced using GEO eco-technology.

Elastic heat and soundproofing material in the form of slabs, intended for use in the construction of frame walls and partitions with a pitch of load-bearing elements of 600 mm. Recommended primarily for the professional construction segment.

Specifications

Dimensions

• Timber or metal framed walls.
• Walls with external insulation along the frame and facing with siding.
• Frame cladding of walls and partitions.
• Walls made of frame sandwich panels.
• Soundproof frame-sheathing partitions.
• Partitions made of stones and blocks, insulation in the middle layer.
• Acoustic ceilings.

Acceptable areas of application

• Pitched roofs with insulation installed between and under the rafters.
• Thermal insulation of a balcony/loggia using mineral insulation.
• Attic floors on beams.
• Roofs made of frame sandwich panels.
• Interfloor ceilings on beams.
• Ceilings on beams over cold basements.
• Reinforced concrete floors, floors with joists.
• Air duct insulation.
• Insulation of industrial equipment.
• Thermal insulation of walls of baths and saunas.
• Thermal insulation of bathhouse and sauna floors.
• Railway transport.
• Water transport.
• Automobile transport.
• Modular buildings (cabins).