How to properly store a gasoline trimmer in winter. Caring for your trimmer in winter and preparing your trimmer for spring. Choosing the best gas trimmer: the main aspects

Preparing the trimmer and preparing the chainsaw for winter storage:

1. Mow/finish everything that needs to be mowed/finished (at the same time, use the fuel so that it is not left for winter storage in the trimmer or for storage in the chainsaw).
2. Remove the tank cap, turn the trimmer (chainsaw) over and drain all the fuel from the tank into a container. technical use(canister or bottle with a funnel for washing engine parts during maintenance). This is the main thing in preparing the trimmer and preparing the chainsaw for winter storage.
   Start the trimmer/chainsaw and use up the remaining fuel from the carburetor until it stalls (if you leave fuel in the system, after a while the fuel will separate and oxides and tar deposits will form in the carburetor channels, which will interfere normal operation engine after winter storage).
3. Be sure to wash everything on the handlebars, everything on the rod and both trimmer protections with warm water and a brush, and do full maintenance of the trimmer - add grease to the gearbox, remove the blade, clean the drive cartridge inside, inspect everything on the trimmer for cracks, bends, abrasions, distortions, breaks (you need to take care of your chainsaw in the same way). Then, for storing the trimmer and storing the chainsaw, do this. air filter, partial disassembly of the engine, washing and blowing it, lubricating moving parts, inspect the condition of the clutch and fine-tune the trimmer carburetor.
4. Preparing the trimmer and preparing the chainsaw for winter storage - unscrew the spark plug, bring the piston to the top dead center (starter), pour 20 gr. motor oil and slowly rotate the crankshaft several times with the starter to lubricate the cylinder-piston group. Reinstall the spark plug (no need to tighten it).
   Trimmer care and chainsaw care during winter storage - once a month it is advisable to remove the candle and make several turns of the crankshaft to renew the lubricant in the cylinder.
5. Wrap the trimmer and chainsaw engine in a rag or bag so that in winter, when temperature drops, when condensation forms, moisture does not get inside the lawn mower engine.
6. It is better to store the trimmer and chainsaw in winter in a suspended state (to save space), preferably in a warm and dry room or in a room with a constant temperature.
7. Take out your accounting notebook as part of preparing the trimmer and preparing the chainsaw for winter storage, analyze and add up your income and expenses for the season, and draw conclusions for the next season (maybe you should increase the cost of your services or buy some specialized tool).

How to prepare your trimmer for spring use

You've taken good care of your lawn - aerated, seeded, fertilized... Now you're waiting. You look forward to warm days and blue skies, and you know for sure that the grass will soon turn green. You've checked the list of things to do for your lawn. Is your trimmer ready? Do you know how to prepare your trimmer? Is your tool in the shed tuned up and ready for the new mowing season? Let's look at the list of things a regular trimmer needs to do to ensure it's ready to do its job (mow) well.

The trimmer motor will work better and will better prepared to mowing, if you add a fuel stabilizer (additive) to fuel mixture. Before long-term storage, be sure to drain all fuel. Then start the engine and run it until it stalls so that there is no fuel left in the fuel system. When it comes time to refuel for the new season, it is very important to use a properly prepared mixture of oil and gasoline. This will ensure proper performance of the 2-stroke trimmer engine. Pre-mixed fuel eliminates the hassle and error of mixing fuel just before mowing. You need to mix enough fuel to use it within a month, no longer, since when stored for more than 1 month, the oil precipitates and the fuel ages.

Before the start of the season, it is necessary to replace the trimmer spark plug, fuel filter, and clean air filter and adjust the carburetor. This will reduce fuel consumption and increase power. For a trimmer with a 4-stroke engine, you need to check the engine oil level and freshness, and also replace the oil filter.

Fishing line, when stored for a long time (for example, after winter storage), can become dry and brittle. To prevent this and increase the life of your fishing line, simply store it in an airtight bag with a small amount of water. And before you start using it (before loading the fishing line into the trimmer head), it is advisable to soak the fishing line in water for several days. Then it (the fishing line) will become more elastic and durable.

A trimmer with attachments provides not only the convenience of performing all necessary work around the yard, but also saves a lot of money, since you don’t have to buy a separate machine for each type of work - just use a specific trimmer attachment. This could be garden shears for trimming hedges, a cultivator for digging up a flower bed, a pole-cutter for pruning trees, a blower for sweeping leaves, etc.

Briefly about preparing the trimmer and chainsaw for the summer season

Spring! It's time to prepare the trimmer for work and prepare the chainsaw for work after winter storage. After you have taken your tool out of the place where the trimmer was stored and the chainsaw was stored, you need to make sure that the gas tool is ready for the start of the season. These few tips will cover trimmer care and chainsaw care to help get your chainsaw or trimmer ready to start after winter storage:

• Check the condition of the spark plug, replace if necessary.
• Check the air and fuel filters, clean or replace if necessary.
• Check your trimmer/chainsaw and, if there are any problems, fix them.
• Tighten the fasteners (check that all fasteners are tight). Do routine trimmer maintenance and chainsaw maintenance.
• It is better to immediately (now) sharpen the chainsaw chain, the brush cutter blade, or replace the trimmer line.
• Add lubricant to the trimmer/chainsaw gearbox, lubricate the cables and friction points of the moving parts.
• Mix the fuel, for this use fresh gasoline (stored no more than 2 months) and fresh 2-stroke oil.
• Once trimmer preparation and chainsaw preparation are complete, start and be sure to let the trimmer/chainsaw warm up for a few minutes before starting work.

Note: for a complete Maintenance and repairs after winter storage of a trimmer or after winter storage of a chainsaw - see the instructions for your gas-powered tool.

Warnings:

The weather is getting warmer and mowing/sawing season is just around the corner. We remind you that clients, children, spectators, helpers, animals, etc. For safety reasons, they must be at least 15 m away from a working trimmer or chainsaw! (care of the trimmer and maintenance of the chainsaw must be carried out in full).

Read the warnings from the manufacturer of your trimmer, which states that children (and adults) can be injured by crushed stone, glass, debris, etc. flying out from under the blade, as well as by the brush cutter suddenly turning around due to recoil when colliding with a stationary obstacle.

How to properly hang a trimmer

An example of attaching a trimmer to a store window: a perforated stand (a wall with holes) into which special wire brackets are inserted, onto which trimmers/mowers are hung.

How Right store the trimmer?

With a trimmer you need to know not only Right contact and store correctly. Often owners gardening tools, without thinking about the properties of a gas or electric scythe, they simply throw the tool into the pantry and lock it. Under such conditions there is a possibility that trimmer will break. Let's figure it out properly store the trimmer Right.

Preparing the trimmer for storage.

If you put the trimmer in the closet at the dacha for a week, that’s one thing, but preparing the tool for “wintering” in the garden house is completely different. Before long-term storage, all wires of the electric trimmer are checked, and all gasoline and oil are drained of the gas trimmer. However, some, on the contrary, do not advise doing this, in order to avoid drying out the gaskets in the mechanism. In our opinion, gasoline should still be drained - both from the engine and from the carburetor, because after 2-3 weeks a sediment may form in the liquid, and this will lead to damage to the lawn mower mechanism.

The best place for storage would be a dry above-ground storage room or a plastic-glazed loggia. But any place away from open fire, isolated from large temperature changes, and with normal humidity will do. If there are no options, and the humidity in the room is high, it is worth covering the trimmer with moisture absorbers. This will save the device from freezing and icing. If you notice that the trimmer is frozen, you should move it to another place, for example, to a closet in a heated room. However, not every gas trimer will fit in wardrobe, this rather refers to small portable and folding electric scythes. Therefore, you can easily move the gas trimmer to the garage.

Storing the Trimmer in the Garage

Storing the Trimmer in the garage.

How to store a lawn mower in winter

Preparing the lawnmower for winter.

What happens if storage conditions are violated?

Typically, all storage conditions for the device are indicated in its instructions. Therefore, you need to read it carefully and not throw it straight into the trash. If, for example, an electric trimmer is stored in the cold, it may freeze up, and when defrosting, the contacts will short out due to accumulated moisture. Such a breakdown is difficult to fix even in service center. The metal parts of any trimmer can rust due to humidity, they will have to be replaced, or even buy a new trimmer.

If the gas trimmer keep close to a stove that is often heated, an explosion of residual gasoline vapors when a spark hits, or ignition, is possible. Here, not only the trimmer, but the entire garden house or cottage. How to properly store a brush cutter A trimmer or brush cutter is the right solution for mowing. After all options for storage locations have been considered and the most suitable one has been selected, a logical question arises.

What packaging should I store my trimmer in?

Better, of course, in the factory. If there is foam inside, then you are very lucky, it absorbs water. IN plastic film keep trimmer not worth it, it causes the accumulation of condensate. In the event that the original packaging is irretrievably lost, you can store the trimmer in a suitable box made of cardboard, plywood or boards. You can wrap the instrument in a breathable fabric, such as one made from natural fibers. You also need to transport the trimmer in the package.

How to transport the trimmer correctly?

We have already mentioned packaging. how to store in winter The trimmer does not start How to wind and choose correctly. If the trimmer is foldable, it should be folded. Gasoline and oil must be drained from the carburetor and trimmer motor before transporting it in the trunk. Check the electric trimmer for the presence of a static charge of electricity; if you feel a slight electric shock when touched, you should not put the electric trimmer on the first seat of the car.

They are powerful and productive gardening units that are used for mowing grass, weeds of varying degrees of hardness and young branches of trees and shrubs. These tools can make life a lot easier for owners. country houses and dachas, in short time and with little effort, simply and quickly improve the lawn, garden and personal plot, vegetable garden Something that could not be done with an ordinary braid.

Regardless of which manufacturing company produced the lawn mower you purchase, its service life depends on proper care and storage.

Where is the best place to store a lawn mower?

During the spring and summer season, grass and weeds are mowed several times, and grass maintenance consists of cleaning its cutting parts and changing gasoline and oil.

When the season of using this tool passes, it is time to think, where is the best place to store a lawn mower? so that after winter it is in the same good condition, does not rust and does not require repairs!

In order for your unit, which is a modern and complex, and usually not a cheap device, to be intact and in working order after winter, you first need to study Operating and maintenance instructions purchased lawn mower, which necessarily contains Rules for storing lawn mowers.

The quality work and the performance of your lawn mower.

Rules for storing lawn mowers

1. The petrol mower must be stored in a room with moderate humidity, dry, and at a temperature not lower than room temperature. At the same time, do not forget about compliance with fire safety standards.

2. The engine of the lawn mower must be cooled before preparing the tool for storage. And all the gasoline is drained. The engine turns on if the fuel is not exhausted, and they wait for the engine to stop itself, when the fuel is exhausted. Since its vapors can contribute to ignition if there is a source of open fire nearby.

3. After that, in order to prepare the lawn mower for long-term storage, you need to rinse and dry the unit. For external cleaning, use a small brush. In this case, you cannot use highly active detergents and household products with aromatic oils that can damage the plastic parts of the trimmer. Then wipe everything dry with a clean cloth. All mechanisms and removable parts must be well lubricated with oil, and metal surface apply special remedy from rust and corrosion.

4. Store the unit in vertical position so that the spark plug is facing up. To protect the lawn mower from damage and dust, a thick fabric cover is put on it, or it is placed in a container so that no one uses it for other purposes. The place for its storage should be inaccessible to children. And the room itself should not only be dry, but also well ventilated.

Today, if special companies that not only help prepare garden equipment for its proper storage, but also provide sets of original parts for each individual unit of a particular manufacturer. Also in these specialized stores you can purchase additional components parts - flexible shaft, spools with fishing line, oil and all types of lubricants, spark plugs. All products meet modern standards quality, which increases the service life of the units.

Every year, summer residents are faced with the problem of preserving equipment before winter storage. Are you sure you know all the details?

It's no secret that before winter storage of equipment, it needs to be cleaned as much as possible and checked for problems with operation and startup. And the more high-tech the device, the longer it will take. Especially to save your effort and time, we have prepared an excellent list of works on proper conservation garden equipment for the winter.

Article topics:

Basic standards for equipment training

Whether it’s a walk-behind tractor or an ordinary shovel for digging potatoes, you must wash it garden tools, let it dry and check all parts and connections for signs of wear before storing it in a dark corner of your garage or shed during an extended period of cold weather.

Maybe, nothing could be worse than moisture, which randomly remained in the dynamic components of the power tool. Freezing, it begins to deform vulnerable parts, rendering any equipment unusable. For personal reasons, it is also worth draining the gasoline, but as for the oil, you absolutely should not touch it. The technique must not be allowed to become “dry”.

What you need to know about storing a chainsaw in winter

Chainsaw It is probably one of only a few gardening tools that can be used as effectively in winter as it is in summer. True, as far as the operating temperature of the chainsaw is concerned, things are worse here, because. gasoline and oil inside it are far from the best frost-resistant substances. But if the manufacturer states that the chainsaw can be used at a temperature (-10 ° C) - this gives the right to safely use the tool. Otherwise, it is better to prepare the chainsaw for proper conservation.

It can be said that " Anyone's heart chain saw is single cylinder two stroke engine carburetor type, of equal importance to which is the chain. Exactly proper care behind these mechanisms will ensure your chainsaw durable and trouble-free operation.

Note! About once a month it is necessary to turn the crankshaft. This will allow the lubricant to be evenly distributed between the connecting rods and pistons.

Service principle:

• to start, it is necessary to drain the remaining gasoline(fuel) from the tank/carburetor. In order to fully verify that it is not inside the chainsaw, run the tool empty and wait for the gasoline to run out. The next step is to wipe the gas tank dry so that its metal components do not rust. This option is great for preservation for 3 months or more. But if you plan to work a little in the winter. In this case, the tank must be filled to the brim with gasoline, and the main thing is that there is gasoline highest quality. You will need to cut down a tree - great, you will already have a tool in your hands ready for work. But do not forget that the gasoline inside can turn into “jelly” after 2-3 weeks of consistency, which can also harm even the best, from a technical point of view, engine.
• dismantle saw chain together with the bar and begin to bring it into pristine appearance gradually freeing from sawdust and other debris. After this, coat these components with a protective lubricant and wrap them in a piece of oil-soaked paper or cloth for storage.
• The last stage There are little things: cleaning the spark plug from burning and gasoline residues, lubricating the worm gear, and cleaning the filter tips;

How to preserve a lawn mower for the winter

Similar equipment every winter deservedly goes on "rest" even with the arrival of autumn, but it comes into operation again only with the beginning of spring. Therefore, when it comes to lawn mowers, their conservation must be treated with great scrupulousness.

The main components of the lawnmower is the engine and mowing parts. They are the ones who deserve maximum attention:

• the first and most important thing to remember is storage conditions. This tool should be stored in a room with humidity not exceeding 70% and without sharp changes temperatures that also increase humidity.
• Be sure to check the cutting components and everything associated with them for the presence of “harmful” moisture, which undoubtedly accumulates in such units during prolonged work mowing grass. Can't be allowed, to moisture appeared in the places of such connections during conservation. Otherwise, the equipment will simply refuse to work in the spring.
• There are two opinions regarding the gas tank. The “old school” of summer residents advises draining the fuel completely and wiping the gas tank dry to rid it of problems with condensation. But there is also alternative way- This means filling the tank with gasoline to the brim. True, in this case it is worth using the highest quality gasoline, but alas, it cannot guarantee success, because... Over the winter, this method can cause sediment to form, which will make it difficult to start the lawn mower in the spring. Therefore, we think it’s easier to drain the leftovers than to take risks in the spring.
• check all cutting elements for signs of wear and replace with new ones if necessary. Also, many manufacturers do not recommend storing equipment during conservation with the wheels in contact with the ground. It is best to store it hanging.

Storing the trimmer in winter

Trimmer- this is perhaps the most unpretentious garden tool for storage, but it also needs to be properly not only handled, but also looked after. Don't just throw your lawn mower in the shed and forget about it until spring. Such negligence can be costly.

Conservation rules:

• store similar technique in a room with minimal humidity, without direct rays of light and sources of excessive heat. But you also can’t let the lawn mower freeze. To do this, you can cover it with moisture absorbers (for example, a bag of potatoes or an old blanket);
• don't forget completely drain gasoline and remove its remains from the gas tank, as well as inspect the spark plug and replace if necessary.
• next, pay attention to the dynamic part of the trimmer - inspect the fishing line / knife and clean it of dirt and other debris. It is best to replace the knife if cracks or chips are visible, and put the fishing line for the whole winter in fresh water. This will allow it not to lose its cutting properties.

Preparing the cultivator and walk-behind tractor for the cold weather

Now it's time to talk about " heavyweights". Motoblocks and cultivators are serious units in the arsenal of any gardener. Therefore, they, like no other, need first of all quality care. Many components, complex mechanisms and dynamic units do not always allow for comprehensive cleaning of such equipment, but trying is not torture and we'll try.

Preservation procedure:

• The first stage in the preparation of such equipment is the preservation of the engine itself, "hearts" of a mechanical beast. Dry the gas tank completely and run the engine until all residue is gone and the car stops. Replace old oil with new oil while the engine is still warm.
• Replace the paper air filter and rinse it from dirt, and then soak it in machine oil and clean the fuel filter.
• Remove the spark plug, remove all dirt and grime from it, and dry it. Pour into the cylinder approximately 15 ml oil and slowly start turning the shaft so that the oil spreads over all parts. Then install the spark plug in its original place.
• This is followed by removing dirt from the gearbox, cutters and other parts. But do not use iron scrapers for cleaning, otherwise you will damage protective layer paint and will subsequently cause rust. This is best done with a wooden stick and under running water. After " water procedures"Leave the equipment to dry for a couple of hours.

Interesting fact! Did you know that every third gardener does not know how to store equipment in winter?

Useful video on garden care from GardenMarket:

During the summer, your lawn mower won a large number of herbs, in gratitude for this, create comfortable storage for it in winter period, so that in next year she didn't cause any trouble.

Clean.

When preparing for storage, thoroughly clean the instrument and open and clean the air filter.

Drain the fuel

Do not store the brush cutter while it is filled with fuel. To avoid clogging the fuel system, drain the fuel from the tank and then start the scythe. Leave the braid on idle speed until the engine stops completely. The fuel system is now ready for storage.

Checking the spark plug

Remove the spark plug and inspect it. The reddish color of the electrodes indicates the serviceability of the spark plug. If the spark plug looks different, it should be cleaned or replaced.

Checking metal cutting tools

If the brush cutter has a metal cutting knife, remove it, clean it from dirt. Check the knife for cracks. If cracks appear on the knife, do not use such a knife (it may lead to tragedy). Purified cutting tool store in a dry place.