What glue to choose for PVC tiles. Recommendations for laying quartz-vinyl (PVC) tiles DECORIA Adhesive for quartz-vinyl tiles

Depending on the type of room and pattern configuration, a specialist lays from 80 to 150 sq.m of material on the prepared floor surface in 8 hours of work.

The installation technology does not involve sealing seams(as for linoleum or porcelain tiles), the tiles are glued to the base of the floor end-to-end. And since there are no seams, the floor is made of quartz vinyl tiles looks like one seamless fabric. This protects the floor from contamination and when shopping and warehouse carts pass over the tiles, the floor does not make any noise.

Coatings must be laid on a flat, clean (without traces of sand, dust, grease, oils, polishes, paints) and always dry base.

It is important to know! Coatings do not allow moisture to pass through, so if you stick them on a base that is not dry enough, moisture will accumulate under the material, destroying the coating and the adhesive from the inside.

The first stage is preparing the subfloor for laying quartz vinyl tiles

The base of the floor can be:

concrete floors with cement screed.
asphalt floors
ceramic floors
wooden floors
metal floors

You can learn more about the preparation and types of subfloors in a special section of our website.

Before starting work on laying the coating it is necessary to measure the moisture content of the screed.
Readiness for the next stage of work is determined in accordance with the residual moisture indicator, it should be no more than 2.0%.
On the concrete base of the floors of the first floors, entrance groups and in wet areas(in the kitchen, bathroom) waterproofing is required.
Further the surface is primed The primer has high penetrating ability and serves to increase the adhesion of repair compounds, as well as for strengthening and waterproofing. It binds surface dust, reduces the absorption of the base, protecting it from moisture leveling masses and glue.
Then you need apply leveling compound, which is intended to create a leveling layer. The brand of leveling mass is selected according to its compressive strength, i.e. according to the degree of load in the room. The thickness of the leveling layer depends on the quality of the screed, but the required minimum is 1.0-2.0 mm.

The second stage is preparing quartz vinyl tiles for installation

The tiles must be kept in place in their original packaging for 48 hours.

When laying coverings on heated floors heating must be in operation for at least 10 days before installation.

During the period of application and drying of the adhesive, the heating must be adjusted so that the temperature of the base is maintained at + 18 ° C. The temperature must remain at this level for at least 3 days after laying the coating.

Required tools and materials:

Knife with replaceable blades: trapezoidal blades are used for preliminary cutting, and C-shaped blades are used for final cutting

notched trowel A2-AZ
metal ruler
square
pencil
styling adhesive
roller (rollers) 65-70 kg for laying floor coverings

The third stage - laying quartz vinyl tiles

Quartz- vinyl tiles should be glued completely, avoiding the entry of air.
For gluing use >glue for PVC laying coatings
It is not recommended to lay the material close to the walls - it is necessary to leave a small gap of 5-10 mm.
It is necessary to roll the floor covering with special heavy (65-75 kg) rollers to remove air bubbles and ensure reliable gluing.
Professionals begin installation from the main doorway, since the first impression of the room is the main thing.
However, you can start in the middle of the room and laying the tiles out loosely to check will ensure the job looks good when finished. This is especially important where drawings are laid out, with the help of which you can hide visual defects, highlight certain areas of the room, or simply decorate the floor. For example, stripes along a room make it visually wider.

Let's get started

Measure the room to be installed in all directions, including recesses, overhangs, etc.
Draw center line A-B at right angles to the wall in which the doorway is located.
Draw line C-D at right angles and in the center of the line A~B
Laying starts from the center of the room.

After this, using the “pyramid” method, lay several partial layers of tiles.

Then, complete rows of tiles are laid using the “layer by layer” method. Next, several more incomplete layers are laid using the “pyramid” method, and so on stage by stage.

Pay attention when laying quartz vinyl tiles

It is important to know!On the back of each tilethere is an arrow indicating the direction, in which all tiles should be laid. If the tiles are not laid in the same direction, the reflection of light will disrupt the planned optical image.If the tiles are laid chaotically, you should not pay attention to the arrows.

Cutting tiles near the walls of the room and “obstacles” is carried out with a trapezoidal knife: the top (protective) layer is cut, then along the cut line the tile is broken and cut on the back side with a C-shaped knife. If the “obstacle” has a very complex shape (for example, a column, steps complex shape, pipe, etc.), cutting tiles should be done using pre-made patterns.

Preparing the base

· As a basis for PVC tiles The following materials can be used:

Cement-sand (cement) screed
Various mixtures specially designed for leveling floors
Plywood with increased moisture resistance (FSF marking)
Bulk, dry bases (Knauf Superpol)
Existing coverings: tiles, porcelain tiles, vinyl tiles

· The base for laying PVC tiles must be prepared in exactly the same way as for ANY other floor covering. The base must comply with the requirements of SNiP 3.04.01-87 and SNiP 2.03.13-88 and be sufficient:

Clean: the surface must be free of any remaining sand, dust, grease, paint and other foreign substances
Durable
Stable
Dry
Smooth

Determining the direction of laying quartz-vinyl tiles

· Before starting work, it is necessary to determine the direction of laying the tiles. Remember that diagonal laying increases tile consumption due to greater trimming.

Aesthetic considerations: a neatly designed entrance to the room, the adjoining of the tiles to visible walls and other structures.
Convenience of the installation process: minimal labor costs, the possibility of simultaneous installation by several workers.
When laying diagonally, the beacon row is usually the longest row, which sets the angle of contact of the vinyl tiles with the walls and structures

Tool for laying quartz vinyl tiles

· Before laying tiles, make sure you have the necessary tools. For quick and high-quality styling You will need:

Line cutting tool. This can be either a professional chop cord or a And lo" (or other sufficiently long object), with which you can draw a straight line.

Roulette
Square.
Rubber mallet.
Knife. It is better to use professional construction knives, but a regular stationery knife will do.
Notched trowel. The choice of spatula is extremely important for correct installation PVC coverings. When choosing a spatula, pay attention to the following:
When laying PVC tiles, ONLY use a notched trowel.
To lay vinyl tiles, use a spatula dosing 300 - 400 g/m2. Using a spatula with b ABOUT Increased consumption of adhesive composition can negatively affect the quality of installation. Do not use a trowel to lay tiles.

The process of laying quartz-vinyl tiles

· Before starting work, carefully read the instructions for using glue or mastic.

· Before applying mastic or glue, it is recommended to prime the base

· Apply glue to the BASE at the rate of several (3 – 4) rows of tiles. The adhesive should be applied to an area that can be tiled in 20 to 30 minutes. Depending on the qualifications of the installer and the configuration of the room, this area may vary.

· Next, you should wait the time necessary for excess (transport) moisture to come out of the glue (gumming time). This time depends on the characteristics of the glue and climatic conditions indoors typically ranges from 15 to 40 minutes.

· To be completely sure that the glue is ready for use, it is necessary to carry out a “finger test”. If the glue is not yet ready for use, then when you touch it it will leave marks on your finger. If your finger sticks to the adhesive layer, but there are no traces of glue left, then you can begin laying the coating.

· Lay beacon rows. Remember that the first row is especially important. The following rows will be adjacent to it. Carelessly (unevenly) glued tiles of the first row will create difficulties for laying subsequent rows.

· Install the remaining vinyl tiles. Styling each next row can be made from already laid tiles.

· ATTENTION: on the products of some manufacturers, on back side There are arrows indicating the recommended direction for laying the tiles. We recommend placing the tiles in accordance with the direction of the arrows.

End of work

· ATTENTION: Do not cover the laid tiles with any covering materials for 72 hours.

There are many options finishing floor surface. One of the recently emerging materials is vinyl facing plates or their improved version - quartz vinyl, where the polymer structure is supplemented and reinforced with fine quartz sand. Laying PVC tiles is not a difficult process from the point of view of a professional. If you want to tile the floor yourself, you can’t do without knowing some of the nuances.

Features of polymer tiles

In order to experience a minimum of difficulties when laying PVC tiles on the floor, it is important to understand the specifics of this type of coating. The material is polymeric and multilayered. Front side The plates are covered with a durable transparent polyurethane film, which gives the material wear resistance, and therefore durability. Further down, the structure of the synthetic cladding is as follows:

decorative layer responsible for the formation of pattern and texture;
supporting base consisting of polyvinyl chloride and quartz sand;
a stabilizing layer formed by fiberglass, giving the plates a constant geometry and dimensions;
mounting vinyl base.

Despite its synthetic nature, quartz vinyl cladding very naturally conveys the appearance of various natural materials, which are often wood, ceramics, and wild stone. Vinyl flooring is not afraid of wet cleaning and exposure to household chemicals. The moisture resistance of polymer finishing plates allows them to be used for cladding not only in ordinary rooms, but also in the kitchen, bathroom and toilet. The advantage of the material, making it competitive with laminate and floor tiles, is elasticity and resilience. Quartz vinyl is much more tactile and dampens sounds well thanks to its porous, multilayer structure.

Vinyl tiles are often compared to high-quality linoleum. Polymer plates really resemble linoleum coating in many technical parameters.

The advantages of quartzvinyl are obvious:

much more convenient to transport and climb to floors;
much less waste, especially in rooms of non-standard geometry;
laying PVC tiles on the floor is not very difficult, either floating or glue method.

The only disadvantage of the material in question is its cost, which approximately corresponds to commercial-grade linoleum. But the advantages of quartz vinyl plates outweigh this disadvantage of polymer cladding in the eyes of many consumers.

Differences in PVC tiles by installation method

Manufacturers have provided two main methods for laying quartz vinyl tiles on a mounting base:

adhesive;
floating (castle).

The first technology involves gluing each element of the polymer cladding to the base of the floor. You can glue the finishing plates using a special adhesive for quartz vinyl tiles. Some manufacturers make the task easier by applying a sticky substance to the back surface facing material and making vinyl tiles self-adhesive.

Laying finishing floor plates using the floating method is possible if the tiles are equipped with joint locks. More often, quartz vinyl is found with adhesive locks, less often - with latches, like those used to join parquet board or laminate.

Requirements for the subfloor

More often, the mounting base for laying synthetic plates is a properly prepared screed made of cement-containing materials, which can be:

concrete;
self-prepared cement-sand mortars;
ready-to-pack mixtures for screeding (levelers);
self-leveling solutions.

Whatever building material is used to level the floor base, the result must be a surface that meets the following requirements:

strength and integrity (the presence of large cracks and peeling fragments is excluded);
flatness (surface curvature should not exceed 2-3 mm per 2 linear meters);
absence from work surface solid particles that can damage the material during further use (careful cleaning must be carried out);
sufficient adhesion with a moderate ability to absorb moisture, which is especially important when installing PVC tiles using the adhesive method (achieved by treating the cement screed with a priming solution);
moderate humidity (after pouring the screed or repairing it, you need to let the material dry).

You can check whether the cement screed has dried sufficiently in this way. A piece of plastic film is placed on the surface and pressed along the edges. If at room temperature After 3 hours, condensation is detected under the film - the base of the floor has not dried enough.

It is better not to use any forced drying of the screed. This will dramatically reduce the strength of the floor base and can lead to peeling and cracking.

Laying PVC tiles on plywood or pressed particle boards(OSB) is used less frequently. Slabs are usually used to level existing wooden floors, or to install plywood over joists, creating a surface for laying polymer facing tiles. To plywood installation basis Almost the same requirements are imposed as for cement screed. It should be smooth, without sharp changes. The seams between sheets of plywood or OSB must be puttied before laying PVC tiles using the floating method or gluing them. When laying on glue, the dried putty is primed. Rest of surface slab material does not require primer treatment - the surface of OSB and plywood boards meets the necessary requirements in terms of moisture absorption and adhesion.

You will learn how to glue PVC tiles to the floor a little later. Now let’s talk about what is needed for a successful installation process.

Preparing tools and purchasing materials

To lay PVC or quartz vinyl tiles with glue, you will need general construction and special tools. From the usual tools the following will be useful:

construction tape (meter);
knife with replaceable blades;
drill with a spiral mixer attachment;
two spatulas (wide and narrow);
construction square;
rubber tamping hammer.

Special tools are a notched plastic spatula and a pressure roller. A regular trowel-comb, used when laying tiles, will not work in our case, since the formed layer of glue will be redundant. The point is not that there will be an overconsumption of glue for quartz vinyl tiles, the price of which is 6-10 dollars per kilogram. Simply gluing PVC tiles onto a thick adhesive layer efficiently will be problematic, so you need a special tool with small triangular teeth.

The second specialized tool is a metal roller for uniformly pressing the polymer plates to the mounting base. The weight of such a tool is about 50 kg and professionals prefer to “tamp” vinyl tiles to the floor with just such a roller. You can replace the heavy metal roller with the usual one used for wallpapering, but then you will have to spend a lot of physical energy, forcefully pressing the roller to the floor when rolling each quartz vinyl tile.

Of the materials that will be needed in the work, you need the polymer tile itself and glue for its installation. Before purchasing what you need, you need to correctly calculate the amount of both. There will be no problems with glue - on each package (hermetically sealed plastic buckets of various sizes), the manufacturer indicates the average consumption per m2. You just need to know the floor area in the room to determine required amount glue.

The number of tiles is a little more difficult to calculate. You need to initially imagine how the installation will be done (along or across the floor). Knowing the width and length of the room, the required number of cladding units is calculated. The width of the room is divided by the width of the plates, the length of the room by the length of the tiles. Niches under heating radiators and entries into doorways are taken into account.

There is no need to make a large supply when purchasing quartz vinyl, since the plates are laid with a minimum amount of material waste.

Having calculated and purchased the required amount of material, and having the necessary tools at hand, it’s time to find out how PVC tiles are usually glued to the floor.

The process of installing quartz vinyl with glue

After preparing the base, you can begin installation work, which do not differ at all when laid on cement screed and plywood. First, the surface is marked for laying the first row, which is usually done from the far wall to the entrance to the room. Sometimes, if the floor geometry is complex or irregular, tiles have to be laid from the middle of the room. In this case, the center must be determined by cutting off the diagonals and finding the point of their intersection. It is convenient to lay square plates from the middle of the floor - this way they will find symmetry on their own. It is more convenient to start laying oblong tiles from the wall. If necessary, the covering plates of the first row are cut along their long size so as not to appear as a too narrow strip to the opposite wall.

Square polymer tiles are preferably laid seam-to-seam, that is, like regular tiles. Rectangular plates are easier and more economical to lay like laminate (laying a row begins with a whole fragment, the next strip of covering starts with a cut piece). The plates are glued end-to-end to form a minimal seam between adjacent tiles. The master’s task is to join the individual facing elements as tightly as possible, while gluing them securely, especially in the places where the plates join, where they most often come off during the operation of the coating.

This is how you should glue the tiles to the floor.

The adhesive mass (before use must be thoroughly mixed with a construction mixer) is distributed over the surface of the screed or plywood base slightly wider than the element to be glued.
Using a plastic spatula, a uniform layer of adhesive is formed. After applying some types of glue, you need to let it sit for up to 10 minutes (carefully read the manufacturer's recommendations).
The plate is placed close to the adjacent, already laid tiles and pressed against the floor over its entire area.
After the initial installation of the tile on the adhesive, it must first be gently tapped with a mallet (rubber hammer), then rolled with a pressure roller. As a result, glue squeezed out from under the plate may appear in the seams, which is immediately removed with a damp cloth or sponge.

If the tiles are self-adhesive, then the task is easier. It is necessary to remove the film protecting the adhesive layer from the back surface of the plates and glue the tiles to the floor base. It is necessary to roll self-adhesive tiles with a roller.

Laying quartz vinyl tiles and PVC plates involves cutting them near the walls to the required size. Cutting polymer material simply - using a construction knife. After measurements, a mark is made on the front surface of the tile with a pencil or marker. The construction square is combined with the mark, forming a perpendicular to the length of the facing element. An incision is made along the ruler with moderate pressure using a knife blade, after which the plate is bent and broken. It is not recommended to use a grinder for cutting tiles - the material melts when heated, and the smell is not the most pleasant.

Using the floating method, quartz vinyl tiles are laid quite simply. Adjacent elements are joined using adhesive locks that protrude beyond the plates themselves on two adjacent sides. It is enough to remove from the locking connections protective film and very quickly join adjacent tiles, making them a single floor covering.

There are many types of tile adhesive. Taking into account the type of work being carried out, the base on top of which the cladding will be attached, the material with which the coating will be made, tile adhesive is selected. For example, if when working on interior decoration vinyl briquettes are used in the premises, then a special connecting mixture must be selected.

This type of flooring will need vinyl tile adhesive. Decoration can be carried out outdoors (decoration of building facades) or interior (decoration of premises). To carry out work outdoors, the binding component must be moisture-resistant, heat-resistant (as with low temperatures, and at high). By doing interior renovation, it is also necessary to take into account the purpose of the room; moisture-resistant glue may also be required.

Adhesive for PVC tiles (click to enlarge)

PVC surfaces are in no way inferior to other types of tiles; rather, they are superior to all other surfaces. Due to their plasticity, lightness, compactness, polyvinyl chloride slabs are simple, more convenient than others, environmentally friendly, have high level wear resistance. It is permissible to use cladding not only on top of the floor, but it is also possible to decorate walls.

Quartz vinyl slabs can be used even when laying heated floors.

Polyvinyl chloride coatings are divided into many varieties according to different characteristics.

For example, according to the production method, polyvinyl chloride surfaces are divided into:

pressed - produced using special plasticizers, in order to improve quality, the entire composition is compressed;
quartz vinyl – this coating is made using natural quartz as a base.
Types of PVC coatings (click to enlarge)
Types of tile adhesive
Tile adhesive differs according to many criteria, but first it is distinguished by the form of production.

With such an abundance of glue, it is difficult to choose the right mixture. You will need special glue for PVC tiles to connect vinyl covering. What kind of adhesive should be used for vinyl tiles? Do you need separate adhesive for quartz vinyl tiles?
What is special about the adhesive suitable for PVC boards?
The connecting composition is truly special, it has many differences:
- withstands low temperatures;
- stable in humid environments;
- provides reliable adhesion of the cladding and the base;
- withstands elevated temperatures, which allows it to be used with underfloor heating systems.
Remember! To choose the right glue mixture, you need to pay attention to some circumstances:
- the purpose of the premises being designed should be taken into account;
- pay attention to the material from which the base for covering is made;
- determine, take into account temperature regime, humidity level;
- take into account the load that will further affect the coating in the future.
Watch the video to find out more:
Only by clearly understanding what material is used and for what purpose, in what room, under what conditions the connection will be made, only then selecting the right glue will not cause you any difficulties, and the process itself will be completed successfully. Based on this, there are several types of glue when installing PVC coverings.
Types of glue suitable for PVC tiles
The binder component suitable for polyvinyl chloride cladding is divided into several types, based on the constituent components and its purpose.
Each type of glue has a complex composition, individual characteristics, and methods of use. The question arises, how to glue PVC tiles to the floor.
Installation features
Lay vinyl tiles on the floor without using glue, like laminate. There are also self-adhesive tiles, which do not require special care, you just need to remove the adhesive tape. Installation process other types of polyvinyl chloride coatings have several features.
- before gluing the slabs, you need to clean the base from debris, dust, and level it;
- the slabs must be glued to the base, starting from the center of the surface to be glued;
- laying out the slabs can be done like laying out a laminate, one after another or according to the pyramid principle;
- prepare glue solution To mix the composition, it is better to use a construction mixer;
- To apply the paste you will need a notched spatula;
- excess adhesive should be removed immediately with a damp cloth, since dried excess will be difficult to remove;
- mounted tile briquettes must be tapped with a rubber hammer and rolled with a roller to ensure better adhesion to the base;
- You can use the pasted surface only after a minimum of 24 hours, a maximum of 48 hours.
From the video you will learn all the necessary information:
Perhaps experienced craftsmen know the intricacies of the process of laying this type of covering, but not everyone has such information, so novice craftsmen need to know about some points that arise during the installation process.
- Before gluing PVC boards over a concrete base, you need to check it for condensation. You can attach the oilcloth to the base with tape and leave it overnight. If condensation has accumulated, the base must be dried;
- It’s worth thinking through the laying principle in advance, sketching out a diagram, especially when laying in diamond shapes;
- you should work quickly, because the adhesive dries quickly;
- If it is necessary to cut off part of the cladding, it is better to do this after attaching the whole briquette.
PVC briquettes are durable, have an attractive appearance, are easy to install, and therefore are quite relevant. The floor can be laid out of vinyl material according to the design idea, using several shades or textures of the material. Such covering requires a special adhesive composition, thanks to which it will last for many years. For example: a two-component or thermally activated component may be suitable for quartz vinyl tiles - this material is used more often for heated floors.
When choosing a connecting compound, you should not be guided by well-known manufacturers or high price. You can choose the right adhesive only by knowing what material will be used and what type of work it requires. In order for the process to end with a good result, you need to take into account some installation features and work with glue correctly, according to the instructions.
Important! The adhesive liquid must be used very carefully: some types set instantly, therefore, it will not be possible to correct any errors that occur.

Compared to the installation of other types of cladding, the connection process PVC boards quite simple and enjoyable. Thanks to abundance adhesive composition, PVC tiles can be connected in almost any room.
Good luck with your selection and easy installation!

Tell me, what type of quartz vinyl tile is SPC tile?

SPC material is the so-called stone-polymer composite, which many manufacturers and sellers call a type of interlocking quartz vinyl tile. In fact, there is little in common between them. Polymer composite - SPC tiles are rigid sheets of plastic with fairly fragile locking systems that do not bend at all during installation and can easily break if handled carelessly. For this reason, this flooring is much more demanding in preparing the base than interlocking quartz vinyl tiles 5mm thick. In this regard, some manufacturers glue a 2mm backing to the mounting side of SPC tiles to avoid problems with its hum and crackling (brittleness) during operation, thereby declaring a total tile thickness of up to 6mm, while in fact the thickness of the tile itself is about 3 .2 - 4 mm. With such a thickness of the tiles, given its fragility, problems arise with the locking connections - they often break even during transportation (when transported to transport companies). The locking system requires careful handling during installation. One wrong move can damage the lock. For this reason, dismantling this floor covering is problematic. Some sellers, faced with this problem, claim that partial breakdown of the locking system is not a defect and the tiles can be laid with such locks.
As for real reviews of the operation of this polymer tiles, then consumers recognize its rigidity, relative to quartz vinyl coatings, without considering this its advantage. Wear resistance and tactile sensations also suffer due to this rigidity. There is no feeling of shock absorption underfoot even with the use of underlays. When laying quartz vinyl, there is no need to use a backing, but with SPC tiles it is simply necessary. Acoustic comfort suffers greatly due to rigidity. In order to find the right substrate for SPC tiles, you need to approach the matter wisely - not every substrate is suitable for installation. You need a dense one - a certain cork or other substrate, but with a high density. If you use a simple foam backing for laminate flooring, the locking system will quickly become unusable under the pressure of furniture and other local loads, and the tiles will heave at their joints.
Thus, summarizing the advantages of this material presented by Chinese manufacturers, we come to the conclusion that these, in comparison with interlocking quartz vinyl tiles, are rather disadvantages due to which this tile inferior in practicality, convenience, wear resistance. Quartz vinyl tiles are softer in operation (“more pleasant to the ears and feet”), do not require substrates, can be dismantled and laid in another place, thicker and warmer, easier to transport, not as slippery as this plastic. The wear resistance of quartz vinyl is higher due to its ability to withstand point impacts - the fall of heavy objects, which easily leave chips on SPC composite tiles.
Well, the most important thing is the environmental side of the issue. You need to think carefully before purchasing polymer-plastic composites from China, or supposedly Belgium, Germany, or Korea. Often, sellers and manufacturers themselves confuse consumers in this in order to hide the real place of production of this material, knowing that China has always been “famous” for cheap production from recycled materials with all the ensuing consequences...

Tell me how to apply the glue, do I need to prime the surface and what kind of glue is suitable for quartz vinyl tiles?

It is not necessary to prime the surface, just remove dust and clean it wet cleaning and let dry. The glue is applied with an A2 spatula with a fine tooth (we give such a spatula as a gift when purchasing tiles) directly onto the base or onto the base + tile (depending on the installation method and type of surface).
Quartz vinyl tiles are laid using contact adhesive or dispersion adhesive. Dispersive is more often used for all absorbent substrates. Contact is suitable for installation on both absorbent and non-absorbent substrates (linoleum, metal, tiles, painted surfaces, PVC coatings), vertical surfaces, ceilings.
When using dispersion adhesive, it is applied only to the base; in this case, there is no need to apply glue to the tiles.
When laying by contact method on vertical surfaces and the ceiling, we smear both the tile and the base, let the glue dry (about 20-30 minutes) and then glue it.
For contact adhesives (for gluing to walls, ceilings and non-absorbent substrates), we recommend KIILTO 2 PLUS (KIILTO TWO PLUS), for small volumes it is sold in 1.4 kg containers, for dispersion adhesives - for absorbent substrates - KIILTO PLUS. Supplied in containers 1.4; 4; 18kg.
Glue for household linoleum Not suitable for gluing quartz vinyl. Also, make sure that the instructions on the can itself state that it is suitable for installing quartz vinyl tiles. Many builders use adhesives that are not always suitable for installing these coatings, without going into the instructions for the purpose of the adhesive.

What can you say about the environmental friendliness of this material? I heard the opinion that these tiles are like industrial linoleum, they emit harmful substances and are recommended in well-ventilated areas ONLY... all sorts of passions have been said... but the same laminate is also not natural!!! soaked in all sorts of rubbish...

Quartz vinyl tiles were developed by Japanese specialists and produced in South Korea. Japanese and Korean companies pay paramount importance to the environmental safety of their products. Emission level harmful substances into the atmosphere allows you to use this design PVC floor tile in public places, homes, children's, educational and medical institutions. The opinion about industrial linoleum is erroneous, since completely different technologies and materials are used in the production of this tile, in particular quartz sand, calcite, which are environmentally friendly clean materials, these components are connected with another main component - vinyl, which is inert material. Currently, a lot of items are made from it (water bottles, food containers and films, etc.) used in everyday life. At the same time, PVC tiles have both mandatory and voluntary examination certificates, which confirmed the absence of harmful emissions in environment and suitability for use of tiles in kindergartens and other institutions.

Is it possible to use heated floors under quartz vinyl tiles?

Yes. When heated or cooled, the material does not undergo temperature changes in size, due to its balanced structure and the presence of quartz sand in the composition.

Is it possible to glue tiles to the wall?

Yes, walls/ceilings can also be finished with quartz vinyl tiles, the only thing you need to do is use contact adhesives, for example KIILTO 2 PLUS glue, which is applied to both surfaces to be glued, wait a while (5-10 minutes) and press firmly against each other. It is allowed to apply glue only to the wall, depending on the type of surfaces on which installation is taking place. Some small areas can also be glued using Moment type glue. Avoid getting Moment adhesive on the front surface of the tile; if it gets in, remove it immediately!

How cold is quartz vinyl tile material? Does it need underfloor heating?

Quartz vinyl tiles have low thermal conductivity, due to this they do not transmit cold well from the base, and their surface acquires the temperature of your room. It is not necessary to install a warm floor underneath it; it is only needed if the room does not have heating and it will be used during the cold season ( country houses, balconies).

How is your tile different from self-adhesive tiles?

Quartz vinyl tiles are laid using a special adhesive for vinyl tiles, which ensures reliable adhesion of the tiles to the base; in addition, it is excellent waterproofing and does not collapse over time. Self-adhesive tiles have an adhesive base similar to double-sided tape, which loses its properties over time, is highly susceptible to temperature changes, and if the base is not sufficiently dust-free, the tiles simply will not stick. You also need to take into account that if you started laying the tiles incorrectly (there is a gap between the tiles), then you won’t be able to re-glue them, you need to either leave them as they are, which will not look aesthetically pleasing and during operation dirt will get into this gap, or tear it off tiles and glue new ones, because the adhesive layer on the old one will already be damaged, and you also need to take into account that during dismantling part of the base may come off, which will entail additional labor costs for leveling the base. Unlike self-adhesive tiles, when laying Quartz vinyl tiles, glue is applied to the base and allows you to adjust the position of the tile, moving it in the desired direction, without losing the strength of the base and the quality of the tile.
In addition, Quartz Vinyl tiles contain crushed particles of superhard materials. natural minerals silicon carbide, corundum and quartz, which guarantees dimensional stability, provides excellent absorbent and springing properties, and provides special comfort when walking. Well, on top of everything else, Quartz vinyl tiles have a minimum wear resistance class of 34, in contrast to self-adhesive tiles, which have a wear resistance class of 22. Please also note that the “self-adhesive” has a total thickness of about 2 mm (together with the adhesive layer), is thin, requires more careful preparation of the base, and when laid on concrete it will be a rather hard floor. Currently, all self-adhesive tiles are supplied from China under the guise of Belgian ones, and what distinguishes Chinese tiles from quality ones is their smell. And of course there is no quartz sand there.

Tell me, is it possible to lay tiles on a concrete floor? The apartment is new, renovated by developers, now there is linoleum on the floor, the floors seem to be smooth.

If by concrete floor you mean a concrete screed, then you cannot lay it on it! This base is not strong and also not level enough. This base needs to be filled with a finishing floor leveler, wait for it to dry and glue the quartz vinyl tiles.

Tell me, what are your tiles laid on, what are the requirements for the base?

Good afternoon, PVC quartz vinyl tiles can be laid on any flat, strong and smooth base. It could be finishing leveler, poured onto an existing concrete floor or plywood, gypsum fiber board or OSB board with puttied (acrylic wood putty is used) recessed screws and puttyed joints of sheets around the perimeter. It should be noted that old coatings, such as loose linoleum and laminate, are not strong enough bases.

I always considered such tiles to be an ordinary subspecies of linoleum, but I see it quite interesting material. I'm going to do some minor renovations in the kitchen and toilet, maybe I'll install PVC tiles. What will happen if water gets on it?

Quartz vinyl tiles are absolutely inert to water, that is, they are not afraid of moisture getting on the coating; moreover, in the event of flooding, they will serve as a kind of waterproofing layer and will not allow water to pass through. Within reason, of course.

We looked at Tarkett PVC tiles in the store and didn’t understand the differences between them and cut linoleum, what is the difference, please explain?

On modern market PVC tiles began to be called all vinyl tiles, but in fact they are different and not all PVC tiles are Quartz vinyl. This is absolutely different materials, both in composition, production technology, appearance and performance characteristics. Including tactile sensations - quartz vinyl tiles are difficult to distinguish from wood by touch, which cannot be said about cheaper analogues.

You say that your tiles have high wear resistance, but you can pierce them with a sharp object anyway, what should you do in this case? Are there any mastics for repair?

One of the advantages of our tiles is their maintainability. If the tile is damaged during use, it can be replaced locally. To do this, the damaged tiles are thoroughly heated construction hairdryer, in the place of the seam, carefully “pick up” with a knife and cut out. After this, the base is cleaned of glue residues and tiles from the repair stock are glued in (it is better to take tiles with a reserve).

How long does it take to walk on glued PVC tiles?

The time the floor is ready for active use depends on the room temperature. At normal room temperature and the correct choice of adhesive for the base, after 18 hours you can carefully move on the floor, not forgetting that the glue has not yet “set” enough; final drying of the adhesive compositions occurs within 72 hours from the moment of installation. Then you can arrange the furniture.

There are interlocking PVC tiles, is it more convenient? And we also saw in a program about repairs a tile with an adhesive edge, glued overlapping edge to edge. What is this?

Interlocking PVC tiles (PVC tiles with the CLICK system) are increasingly being produced with a thickness of 3-4mm, which is only 1-1.5mm thicker than regular tiles (glued to the base using glue for PVC coatings), while it is just as flexible, and therefore it needs absolutely the same level, dry, clean base as under the adhesive one. The lock on such a tile, if of course you can call it a lock, is a “tongue-and-groove branch” made of PVC about 0.3-0.5 mm thick. If the covering is laid on an uneven base, then this “lock” will not withstand the normal load to which the floor covering is subjected - the locks will bend, tear over time and the tiles will corrode. The seam will be exposed. Over time, moisture, dust, and dirt will get into unglued seams, which will continue to “grow” the resulting gap. Also among the significant disadvantages is the lack of repairability of the coating, because it cannot be cut out (one damaged tile) and inserted, as is the case with glued PVC tiles. You will have to disassemble the entire floor (similar to repairing laminate), and a second high-quality installation, given the appearance of the “locks,” will probably not work. The same aspects of operation and installation can be applied to tiles with so-called adhesive tapes around the perimeter. Not even the strongest double-sided tape will withstand the mechanical and temperature influences to which any floor covering is exposed, and will also not withstand moisture, which will always penetrate inside this structure and destroy it. Nothing at this time can qualitatively replace a layer of adhesive composition, which provides strong adhesion to the base. The base must be level in any case. Saving on foundation preparation in order to purchase expensive castle covering, or coverings with adhesive tape around the edges - will not give the desired economic effect. We advise you not to skimp on preparing the base, to buy an appropriate floor covering, the operation of which has been proven over the years at many facilities, and to glue it to the base, so that later you won’t feel bad for the unprepared base, and for spending significantly more money on purchasing a covering that was initially captivating its ease of installation, beautiful advertising. Well, if you still don’t want to “mess around” with glue, and are ready to spend money on an interlocking one, then choose a tile with a thickness of at least 4.3 mm (it has a stronger interlocking connection), and a length of no more than one meter ( optimal size For interlocking tiles, in which there is no shrinkage along the length, as often happens with large longitudinal dimensions - the end connection diverges, dirt gets there). Also pay attention to the size of the tiles - many manufacturers general indicator length and width add 2-3 mm of the lock, but in fact it is not a useful area, and for decent volumes the buyer pays “for air”, as a result there are not enough tiles, because no one takes these millimeters into account, but in fact they turn into square meters hidden in locking connections. Demand calculus" usable area", without taking into account the locking connections!

What is more profitable to lay - linoleum or quartz vinyl tiles?

What do we have when purchasing linoleum? It is inexpensive and easier to lay (which is not always the case, by the way). This is where its advantages probably end, because when purchasing linoleum, we are faced with problems that do not exist with quartz vinyl tiles: dents from furniture and high-heeled shoes remain on it (this topic does not particularly concern people until the moment they purchase New furniture, or decided to change the decor in the house), linoleum is slippery, wear-resistant commercial linoleums have a “non-home-office” appearance. Linoleum is more difficult to transport; linoleum does not convey the texture of wood, as is the case with quartz vinyl tiles, but behind linoleum, which has a similarity wooden surface The porous surface is very difficult to care for, dirt gets clogged into the pores, and cleaning them is very problematic; linoleum is not repairable (the patches are visible and do not restore the previous appearance). The appearance of linoleums also leaves much to be desired. There is no feeling of a solid floor. Therefore, if we consider in more detail the costs of operating the floor covering in the long term (for a long time), then it will definitely be more profitable and wiser to purchase and glue quartz vinyl tiles one time, than instead to buy and re-lay linoleum 2 times, removing all the furniture from the rooms, and having other related problems.

Now there are PVC tiles with a thickness of 3 mm and with protective layer 0.7mm, only it is Russian, not Korean. Does it have better characteristics?

Since PVC tiles began to have a thickness of 3mm and a protective layer of 0.7mm, this did not add significant changes to its structure from the previous 2mm thickness. There is no quartz sand or other super hard minerals present in quartz vinyl. It is these components that provide the tile with density and hardness. In turn, density and hardness ensure that the tile will not be subject to stretching, shrinkage, changes in its linear dimensions during operation, and will not sag (press through) under the influence of heels and furniture legs, and, therefore, the load on the protective layer will be minimal, and it will last longer in the end. In the case of just PVC tiles with a large protective layer, it is the same as putting a hero’s helmet on a thin hero, will the hero withstand the blow... If there is no dense base under the helmet? In this floor covering All indicators play a role, and not just the size of the upper protective layer. After all, commercial linoleum with a protective layer of 0.7 mm has already been invented, but over time, “paths” still appear on it in places where people constantly walk. This soft material. Here are the main differences. Ask for the tiles, touch them, compare them, and make sure.