Clinker tiles for interior decoration. Clinker bricks for finishing interior walls Decorative clinker bricks for interior decoration

The concept " clinker brick"appeared in Russian usage relatively recently, however construction material used more than 200 years. Refractory brick appeared in Europe - Holland is considered to be the birthplace of clinker.

Material made from special clay, not inferior in strength natural stone, became popular first in European countries, then in the USA, and over the last two decades in Russia. The scope of application of clinker is extensive: from paving garden paths to interior decoration walls

Clinker - what is it?

Clinker bricks differ from analogues in production technology. The main component is refractory clay, from which rectangular blocks are formed. Bricks made by extrusion are used in the construction of load-bearing walls. For interior decoration, you can also use pressed material.

At a temperature 1 100-1 450 o C the clay is compacted and sintered into a monolithic bar, which is free of cavities and foreign particles. It is this feature that makes clinker a universal building material used for various jobs:

façade cladding;

interior decoration;

decorative design of window and door openings.

erection of columns;

reconstruction of old buildings;

V landscape design– paving clinker.

To create original architectural compositions, they are glazed: covered with a double layer of paint and re-fired. As a result, colors, constantly exposed to aggressive environments, do not lose their original brightness within 5 years.

The ultra-dense monolithic structure gives ordinary clinker bricks increased performance characteristics (see table).

Original appearance and a wide color palette make it possible to create entire architectural compositions from clinker, emphasizing the uniqueness of the building.

The manufacturing technology completely eliminates the addition of chemically active and toxic components to the composition.

Types of refractory bricks

The modern building materials market offers three types of clinker bricks. Products are classified according to their intended use. It looks like this:

Building. Designed for construction supporting structures and load-bearing walls. This single brick, resistant to any loads and external factors.

Facing. Applicable for internal or exterior finishing, available in various color scheme. The glazed surface makes the brick resistant to various atmospheric conditions and ultraviolet rays. Models in this group can be produced in a traditional rectangular design or a shaped version.

Sidewalk. This brick has an increased wear resistance of the surface, so it does not lose its appearance even with long-term use. Used for landscaping personal plots, design of park alleys and pedestrian paths.

In any case, the products comply with the standards GOST, which determine the main technical indicators.

Size range of building materials

Regardless of the manufacturer, all products adhere to certain standards, which greatly simplifies the process of purchasing material. Three standard sizes are used as a basis, as indicated by the brick markings:

1 SF. This is a single brick, with sides measuring 250*120*65 mm.

1.4 SF. Classification one and a half brick with dimensions 250*120*88 mm.

2.1 SF. Double brick with characteristic dimensions 250*120*140 mm.

In addition, there is Eurobrick on the market, which is labeled NF 0.7 And SF 1.3 with dimensions 250*85*65 And 288*138*65 respectively. This group also produces half-size products, which are named after the fractional part of the whole brick: half, quarter, three-quarters.

According to requirements GOST, clinker brick must have the shape of a regular parallelepiped, permissible deviation along the length of an individual block does not exceed 4 mm.

Interesting design solutions using clinker bricks indoors

Thanks to the appearance of clinker, you can create original compositions for interior decoration. The most popular are four architectural styles.

"Loft" - imitation of an old building

In the first half XX century There was a shortage of housing space. Representatives of the creative elite are beginning to rent abandoned factories and attics for studios. This is how the “loft” style arises - an imitation of the interior of empty and old buildings.

Clinker brick can be used for interior decoration, but it will not be possible to reliably imitate old brickwork for a number of reasons:

equal thickness of seams;

repeated surface irregularities;

no masonry defects.

Conclusion: the material can be used with restrictions, in the form of “additives” to wood and natural brick.

"Country" - return to roots

Country style implies an interior in the style rural house. In the 21st century A new direction, “ethno-country,” has come into fashion, that is, recreating the interior of homes of different peoples or even different eras.

Clinker bricks can be used for the following purposes:

fireplace lining;

creating an apron in the kitchen;

room zoning.

The “country” style is characterized by straight lines, brown and burgundy colors, so the material described looks appropriate and harmonious.

"High-Tech" - in the world of high technology

Avant-garde style designed to combine the incongruous. The interior is characterized by minimalism, straight lines, simplicity and convenience. The main finishing materials are concrete (brick), glass, metal.

The dominant color of high-tech rooms is white, which is why clinker bricks are used in the same color.

If you have the desire and artistic taste, you can choose amazing combinations of glass and stone, brick and plastic. The main thing is not to overdo it and carefully study what limitations this style has.

English style - a combination of aristocracy, sophistication and restraint

English style designed to recreate the atmosphere of respectable England late XIX century. Widely used wooden panels, ceramic tile, luxury wallpaper. Clinker would also be appropriate.

beautifully decorate the fireplace area in a country house;

make a small partition in the hallway with a deliberately uneven part of the masonry;

design kitchen apron or lay out a column to which the tabletop will be attached;

lay out one of the walls of the bedroom or living room so that the antique masonry is in harmony with modern ceiling or flooring.

In general, brick cladding provides almost limitless possibilities, so everything will depend on individual preferences or the designer's imagination.

Masonry in this case is not technologically complex process, but has a number of features. The process boils down to following these steps:

All are completed completely preparatory work, drawings are made, markings are carried out.

The first row of bricks is laid out. This is done without mortar and is necessary to determine the geometry of vertical joints.

Installation is carried out sequentially, in rows with a constant masonry height ratio.

It is better to leave the seams thick enough ( up to 10 mm).

Walls with ventilation voids are erected according to the following scheme: through every 4 rows an empty seam is left, which is covered with thermal insulation material.

After raising several rows, you need to wait for the solution to dry. At this time, the seams are usually prepared for grouting by removing the mortar with clinker to a depth of 1.5-2 cm.

Grouting or jointing is performed after 5-7 days after the walls are built. For this, two types of solution are used:

Grey. Preparation proportion: to one part of cement 4 parts quartz sand With maximum fraction 2 mm.

White. The ratio of components is similar to the previous option, but here only a special brand of white Portland cement is used.

Grouting is necessary to protect joints from moisture, improve the appearance of the masonry and increase heat and sound insulation.

Joining of clinker bricks is assumed in cases where it is not planned finishing walls

There are five grouting options:

Flush– the solution fills the voids, is leveled over the surface of the brick, and the excess is removed.

Concave– grouting is carried out according to the previous scheme, but then the seam is passed with a jointing trowel.

Convex– is performed using an arc spatula, which is applied to the seam and the voids are filled with mortar.

Rectangular– for interior finishing, vertical and horizontal seams are filled with a composition that differs in color.

Beveled– the seams are filled with mortar, which is then trimmed with a trowel at a slight angle.

Each option has its own characteristics, but all grouting methods look very original.

TOP 3 trusted manufacturers

When choosing a material, you need to take a responsible approach to choosing a manufacturer: this is the key to quality products. In the case of clinker bricks, we advise you to pay attention to the collections of the following brands.

"Kerameya". Ukrainian company, famous since 2006. The first batch of clinker bricks was produced in 2008, in the same year the enterprise reached its planned production capacity: 30 million units annually.

Currently, the company produces more than 100 names of products is largest producer clinker in Ukraine ( over 70%).

FELDHAUS KLINKER. German company with 160 years old history. The company was founded by the Feldhaus family and for five generations has been producing clinker bricks according to ancient recipes, but using modern technologies.

Unlike most European companies, the Feldhaus group adheres to a reasonable pricing policy, which makes it the world's leading supplier of clinker.

"MosKeram" Russian company operating in Moscow and the region. The manufacturer adheres to high quality standards, constantly expands its range and the lineup clinker bricks.

Besides, positive reviews builders deserve Russian companies "LSR Group" And "Alta profile", products of a Polish company ROBEN.

The Plitka-Kirpich company offers to buy brick tiles own production for interior decoration. Large selection, high quality, delivery and reasonable prices.

Our assortment includes brick-like tiles for interior decoration made of concrete and gypsum in various shades, which allows you to choose the material for finishing the interior of any room - living room or bedroom, corridor, bathroom or kitchen. Brick tiles will look appropriate anywhere, because they go well with many other finishing materials: wallpaper, lining or plaster.

Prices for our tiles

As a direct manufacturer, the Plitka-Kirpich company not only guarantees the high quality of our products, but also offers affordable price on brick tiles.

The cost depends on the material from which it is made, and on average is:

imitation brick made of concrete - from 1250 rubles. for 1 m2;
gypsum tiles – from 700 rub. for 1 m2.

You can order from our company decorative tiles under brick not only in Moscow, because we deliver throughout Russia using transport companies. It is also possible to pick up products from our company’s warehouse. You can familiarize yourself with the delivery conditions in the corresponding section of our website.

In addition, Plitka-Kirpich specialists provide Additional services for professional installation of brick-like tiles, which allows you to transform the interior country house or apartments quickly, efficiently and inexpensively.

What is this tile?

Brick tiles are a popular building material, used not only for decorating facades, but also for interior decoration. Thanks to the many colors and textures, it can complement any interior, especially if it is made in the loft style.

The catalog presents brick-like tiles for interior decoration in a variety of colors, and choose suitable option You can use a photo. We offer to buy tiles for the wall, made in the form of noble white masonry, classic dark red brick, or cladding to look like old brick.

Decorative cladding imitating brick has a number of advantages that distinguish it from other types finishing materials.

The advantages of concrete brick tiles manufactured by our company are:

Aesthetics and attractiveness. Each tile has a clear geometric pattern, smooth and clear lines, big choice colors and textures.
Strength and durability. Concrete facing tiles are resistant to mechanical damage and scratches, they are less susceptible to wear compared to other types of finishing.
Light weight like this facing material does not create additional load on the supporting structures of the house and foundation.
Versatility. Decorative tiles that imitate brick look absolutely harmonious in rooms. for various purposes– it is widely used for finishing as living rooms, both commercial and office premises, as well as restaurants, hotels, cinemas, etc.
Eco-friendly and easy to care for. The facing tiles produced in our company are an environmentally friendly and safe finishing material. It is easy to clean from dust, is of high quality and is made from raw materials of natural origin.

In addition, we offer affordable prices for all our products and guarantee their high quality, strictly controlling and monitoring every stage of production.

With the right design approach, a brick pattern will fit perfectly into almost any style. Facing tiles made to look like old, darkened brick will fit perfectly into an interior in the Baroque or avant-garde style. A small fragment of white brickwork is suitable for modern or minimalism.

A solid brick wall is characteristic of the loft style, which is based on the imitation of abandoned premises and workers' housing. It is the loft that involves decorating the room almost entirely with brickwork. To decorate in a loft style, you should use decorative tiles, the color of which is as close as possible to the natural material.

You can use brick-like tiles to accent one of the walls of a living space, decorate a hallway, bathroom, shower or steam room. Besides this, this decorative material can be ordered for laying out an “apron” in the kitchen or finishing the fireplace and the wall next to the hearth.

We offer high-quality decorative brick-like tiles in a variety of colors that are suitable for finishing any interior. Profitable terms, delivery throughout Moscow and throughout Russia, installation and quality assurance. Call!

Interior decoration with clinker bricks is an elite class solution that only wealthy people can afford. You can buy clinker bricks for interior wall decoration in Moscow at a price of 18 rubles per piece.

Let's consider what exactly attracts this option wall cladding:

Excellent sound insulation performance is achieved due to the large width of each clinker product. The structure of the material also contributes to the complete neutralization of the sound wave, taking the entire impact on itself.
Combination color solutions and textured surfaces provides complete freedom for designers in interior design.
There are legends about the strength and resistance to stress of clinker. Special technology industrial production has been developed for centuries. Numerous attempts led to the successful completion of the search for the ideal chemical formula.
Environmental Safety. Clinker is a “green” material in terms of compatibility with environment and harmlessness towards living beings.
The appearance of clinker bricks for interior decoration creates an atmosphere of fundamentality and wealth.

Carrying out facing work

Preparing the surface to which the bricks will be attached consists of creating an ideal, flat plane. All minor irregularities, bulges and bends must be eliminated. Holes and cracks must be sealed with mortar.
Treatment with a special moisture-resistant composition, which will also create an additional dust-proof layer of bricks from particles from the wall.
Facing is carried out in the direction from bottom to top. It is necessary to carry out operations with due care and precision to correctly join the seams of the edges of clinker bricks. For a more expressive look in light colors, it is recommended to additionally paint the spaces between the products in a darker color.
There is no need to carry out additional painting, because... the color of clinker for interior decoration is extremely resistant to chemical agents and ultraviolet rays. It does not fade over time due to its special chemical composition.

Strengthening the load-bearing supports and foundation is also impractical; the products are light in weight and do not place increased loads on the system.

Differences from other options

An alternative to brick is. It's cheaper and installation work in this case they are also simplified. However, the tiles do not give the feeling of reliability and solidity of the structure that is typical for brick blocks. In addition, it does not have high levels of heat and sound insulation.

It is also necessary to distinguish between the concepts decorative stone and brick. The sizes of clinker bricks, although varied, are still strictly standardized. The facing stone is a product various shapes and textures that form a mosaic.

Decoration of walls inside the apartment, as well as the facade of the house decorative bricks or a material that imitates brickwork - has never gone out of fashion. However, unfortunately, it is not always possible to use real brick for interior decoration, as it will weigh down the floor slabs of multi-story buildings. In addition, making ideal masonry “for jointing” is not so easy, because this requires at least minimal experience as a mason.

Much easier to use others interesting ways that allow you to achieve the desired result. Brick imitation can be produced in different ways and, which is typical, can be installed by anyone, even a novice finisher.

Considering the fact that brickwork has remained popular for decades and is used to reproduce various interior styles, manufacturers did not miss this moment and developed several types of material that can replace natural brick.

This type of finish is made in different forms– it can be flexible or rigid tiles, the size of the end side of a brick, or large Wall panels, immediately covering an entire section of the wall, made from polyvinyl chloride (PVC), MDF or fiberglass cement.

Flexible brick-like tiles

Flexible tiles that imitate brickwork are great for interior and exterior wall decoration. This modern material is not only decorative, but also protective coating for surfaces and has a number of positive qualities - this includes resistance to external atmospheric influences, impact resistance, vapor permeability, inertness to microorganisms, as well as ultraviolet radiation, and, of course, an aesthetic appearance and a fairly simple processing and installation process.

“Flexible brick” is easy to install not only on straight, level surfaces, but also perfectly bends around external and internal corners premises.

This material is used to decorate walls inside apartments and houses, in particular, in rooms such as hallways, corridors, kitchens, living rooms, loggias. It is also suitable for external façade walls. It is very convenient to use such tiles for cladding columns, fireplaces, small architectural forms, as well as in any areas where such design is planned. Regardless of the complexity of the surface configuration.

The tiles can be used to finish the entire wall or attached to individual sections. Since the material has many colors, it is possible to make the finish monochromatic or use tiles of different shades, harmoniously combining them with each other.

Installation of “flexible brick”

For installation flexible tiles no complex electric tools. You will only need to prepare:

— an even spatula 120÷150 mm wide – for mixing and applying glue;

- a notched trowel with a ridge 4 mm high and 150÷200 mm wide;

— building level 1000÷1500 mm long;

— a ruler 1000÷1500 mm long;

- colored marking cord for marking lines;

- a simple pencil;

- powerful scissors;

- a brush 12 mm wide for leveling the mortar in tile joints.

For materials other than tiles, you will need a primer for the walls and a special

For installation, a dry construction mixture can be used - ordinary tile adhesive, but it is more convenient to use a ready-to-use composition packaged in plastic buckets. In any case, when purchasing tiles, you should immediately consult with the seller regarding the adhesive suitable for a particular material.

In order for the masonry to be smooth and neat, the wall must be put in order before installation, by cleaning and leveling its surface. After the leveling solution has dried, the wall must be primed with an antiseptic composition, which will give the materials higher adhesion and will not allow mold to appear under the cladding layer in the future. Once the primer has dried, you can proceed to installing the tiles.

In addition, you need to take into account that installation work must be carried out at a temperature not lower than +5 degrees, otherwise adhesion between the materials will be insufficient, and the tiles may subsequently begin to peel off from the surface of the walls.

Prices for imitation bricks

brick imitation

The first step is to outline the wall surface into even zones along which glue will be applied and the tiles will be fixed. If the entire wall is to be covered, then it is necessary to beat off the upper and lower limiting lines.
The glue is not applied to the entire surface, but to individual, marked zones of about 1000×500 mm. The layer of adhesive mass should be approximately 2÷3 mm - it is applied using an even spatula, and then distributed over the entire area to be covered with a notched trowel to create grooves of the same height.

The tiles are glued in order, and if the first row starts with a whole tile, then the second - with half or one third of the “brick”, depending on the desired location of the masonry seams.

Dividing the “flexible brick” into pieces at any angle, without using any power tools, is quite simple: it is marked and cut along the line with ordinary scissors.

The seams between the rows can have different thicknesses - this parameter will depend on the preference of the master, but usually the gap is left at 10 ÷ 12 mm. The selected size of the seams is taken into account immediately when marking the wall into zones for installation.

“Flexible brick” easily bends around protrusions formed at any angle, as well as internal corners or rounded walls, if they exist on the surface to be finished.

When the intended surface area is covered with tiles, you need to immediately level the mortar in the horizontal and vertical joints, otherwise the glue will set and it will not be possible to accurately level it. Smoothing the solution is carried out using a relatively thin brush of medium hardness, slightly moistened with water.

The fact that flexible tiles do not require additional purchase of grout for joints can also be safely called an advantage of the material, since you do not have to incur extra costs.

Video: flexible facing tiles with excellent clinker brick imitation

Rigid facing tiles “brick-like”

Clinker tiles

Clinker tiles are used for internal lining walls not as often as other types of material imitating brick, as it has a fairly high price. It is often purchased for facades, given its highest performance characteristics. However, it can also be used for interior decoration, especially if you are going to cover a stove or fireplace.

It is made from natural highly plastic clays, without the use of artificial dyes and plasticizers. The raw materials are pressed and fired at high temperatures, reaching up to + 1150÷1200 degrees. Thanks to this, clinker tiles are environmentally friendly pure material, which has unsurpassed natural qualities of durability and reliability, which are multiplied during the production process.

This finishing material is perfect for both interior and exterior facade cladding. It has a very low moisture absorption coefficient, high frost resistance and wear resistance, inertness to temperature changes and almost any chemical influences.

Decorativeness clinker tiles is not inferior to its physical and technical characteristics, since the variety of design options allows you to choose a material to suit every taste and style of the interior of the premises or the facade of the building. The finish can have a rough, glazed or natural, untreated surface. Tiles on sale different sizes and shapes, and this factor also allows you to bring the most daring design ideas to life.

Installation of brick-like facing tiles

As mentioned above, all tiles that have a certain rigidity are mounted on the wall in approximately the same way. For the work you will need the same tools as for “flexible brick”, and in addition, to cut this material you will need to prepare a hand-held circular saw or grinder with a disc on stone.

The work of laying cladding from this type of material is more complex, since the finishing already has significant weight, and after installation it requires careful sealing of the seams between the tiles.

The cladding process is carried out in the following order:

Laying should be done on a prepared, primed and relatively flat wall.
Marking the wall surface is carried out in the same way as for installing any piece of cladding material: straight lines are struck along the upper and lower levels of the masonry, then it is recommended that the entire distance between them be calculated and divided horizontally so that the intended number of rows can be accommodated in this area masonry, with mandatory consideration of the thickness of the seams between them. It is especially important to carry out this process if you do not have sufficient experience in wall cladding - marking will help make the masonry perfectly even.

When marking, you need to allocate 10÷12 mm to each of the seams between the rows.

Next, an adhesive mass is prepared, which is selected in accordance with the type of material on which the finishing tiles are made.

Laying begins from the bottom row, which is carefully verified by the building level, since the accuracy of the entire wall cladding will depend on its horizontalness. If the first row starts with a whole tile, then the second and all subsequent even rows start with ½ or ⅓ tiles.
Next, glue is applied to the wall with a spatula in a layer of 3 ÷ 4 mm. After this, the mass is distributed with a notched trowel, which leaves grooves of equal height, ensuring the most uniform distribution of the adhesive when pressing the tile. When laying some heavy types of tiles (the same clinker), it is additionally recommended to apply glue to back side facing material. Therefore, before starting work, you should be sure to study the instructions included with the package, which clarify the nuances of installing a specific material.

During the installation process, it is necessary to monitor the evenness of each of the laid rows.

To ensure that the width of the seams between the tiles on the entire tiled surface is the same, some craftsmen use special calibrator tabs of the same size. They are temporarily installed between the rows, and after the adhesive mass has set, they are removed and installed again, but on the upper rows. As such calibrators, you can use a wooden bead or silicone posts.

For cladding external corners special shaped elements are used that can disguise existing chips and make the corners neat and protected.

Upon completion of the masonry and after the glue has completely dried, the seams between the tiles must be securely and accurately sealed using grouts specially designed for this purpose. You can fill the seams in different ways:

- Use ready-made compositions in tubes, using a special gun.

— Place the mixed grout in plastic bag, and then cut off one of its corners diagonally to the width of the seam and carefully squeeze the solution into the gaps between the rows.

Unlike PVC panels, MDF finishing is not recommended for use in rooms with high humidity, but it is perfect for lining the walls of hallways, corridors, insulated balconies, and living rooms.

Manufacturers also thought about the design of the corners, making special shaped elements for this.

Glass fiber reinforced concrete panels

Special mention should be made of glass fiber reinforced concrete panels. This facing material is made on the basis of ordinary cement with the addition of glass fiber, which increases the strength of the slabs tens of times. For external decoration, panels can additionally be reinforced with metal elements, which increase the weight of the structure, but make it resistant to mechanical stress.

Reinforced only with fiberglass, the panels do not have a particularly intimidating weight, and their dimensions are still compact in thickness. The solution for their manufacture is colored in the mass, so the slabs are not afraid of small chips and abrasions. When producing molding sand, some manufacturers add colored glass fiber to it, which is slightly darker or lighter than the main tone, but is in perfect harmony with it - this gives a very interesting effect. In addition, additional application of paint to the surface of finished and assembled products is allowed.

It is well suited for interior decoration, but still more often it is used to transform the facade of the walls of a building.

Environmentally friendly slabs do not weigh down the walls, as they have a small mass. They perfectly protect surfaces from moisture and mechanical influences, as well as from the penetration of radio emissions into the house, and have a number of other attractive advantages. However, the cost of such facing materials is quite high, so not every owner can afford such finishing.

Installation of brick panels on the wall

If the wall surface is fairly flat, then the panels can be fixed to it without installing a frame structure. Lightweight PVC boards are glued to a cleaned and primed surface using one of polymer adhesives. For example, “liquid nails” are well suited for this.

Finishing panels based on MDF have significantly more weight, so in addition to glue, they are fixed to the wall with dowels in four to five places.

Glass fiber reinforced concrete panels can be fixed to flat wall using cement-based tile adhesive.

In the case when the wall surfaces have significant distortions, they are corrected by fixing frame structure, consisting of metal guides or wooden beam, set exactly in the required plane according to the building level. Some manufacturers make special subsystems for their products, mounted on the wall or on installed frame. In this case, the panels are hung on special elements of the subsystems.

Subsystems may have different designs, therefore, when purchasing facing slabs and fastening systems to them, it is necessary to check the compatibility and availability of the attached installation instructions.

It is clear that if you plan to install panels on a subsystem, the frame elements must be located in accordance with the features of this model.

The most simple view fastenings have plastic panels, made according to the principle of siding construction. They have a special perforated mounting strip in the upper part, through the holes of which the slab is fixed to the wall or frame. In this case, horizontal sheathing elements are fixed to the wall surface, at a distance from the visible part of the slab.

Prices for facing bricks

facing brick

Installation of any cladding panels starts from the bottom of the wall, usually from the corner elements.

Homemade wall design options for brickwork

If you want to save money by making an imitation of brickwork on one of the walls of an apartment or house with your own hands, you can use original techniques developed by folk craftsmen.

There are several common options that do not require special costs for the purchase of facing slabs or panels, and also do not create any particular difficulties in installation:

Self-production of polystyrene foam tiles with a thickness of 10÷12 mm. For this purpose, it is recommended to use extruded material with higher performance indicators than conventional white foam.
Creating a brickwork relief using a stencil.
Reproduction of the desired pattern on the wall using masking tape.

Brick-like tiles made of polystyrene foam

If you plan to use the process of melting the edges of foam plastic in the manufacture of tiles, then the work should be carried out on outdoors, protecting Airways using a respirator, since this material is flammable and releases toxic substances when burned and melted.

The first step is to mark the “brickwork” on the prepared, leveled and primed wall surface using a ruler, plumb line, building level and a simple pencil. The wall is drawn into horizontal stripes and vertical partitions, which determine the size of the bricks and the seams between them and the masonry rows.
The second step is to mark the sheet of polystyrene foam into tiles of the selected size.

The material is then cut into individual elements stationery knife. The number of such blocks must correspond to the number of bricks required to decorate a certain section of the wall on which the marking was made.

Next, in order to achieve the most reliable effect of imitation brick, you need to work on the resulting tile - this can be done in different ways. Its surface is treated with sandpaper in different or one direction, and notches and grooves are made on it with a knife or other sharp instrument. You can also use a heated soldering iron for these purposes.

Another option is to melt the edges and outside of the tile using a regular lighter or torch. In this case, the front surface takes on soft, smooth shapes.

After painting the tiles in the chosen color, its relief will be more pronounced. Paint can be applied before installing the tiles or after the wall cladding is completely completed.

Painting can be done using a brush or spraying the coloring composition from a can. The main thing is that the paint does not cause dissolution or softening of polystyrene foam - it is better not to experiment with organic-based compositions, giving preference to water-soluble ones.

Laying of foam tiles is carried out according to wall markings using “liquid nails” glue, which is applied to the back surface in three points with a thickness of 3–4 mm.
The final stage will be the design of the seams between the bricks and rows.
It should be noted that if the design does not provide for highlighting the tile joints with a different color, then painting the cladding can be done after the grout solution has dried.

Imitation of brickwork using a stencil

In order to make an imitation of brickwork using a stencil, you will need a cement-based mortar. It is best to purchase it in the form of ready-made dry construction mixture for plastering work, since it already has all the necessary additives that make it plastic and convenient for work.

The solution can be made independently from two materials - this is a plaster and adhesive cement mixture, which are taken in proportions of 1:1. To increase the plasticity of the solution, add a tablespoon of liquid detergent per 5 kg of the finished mixture.

The wall must be well cleaned, primed and dried.
The solution can be applied to its surface using wide spatula or simply with a rubber gloved hand. The thickness of the applied layer should be equal to the thickness of the stencil strips. This moment will depend on what kind of surface the brick should have - smooth or rough.
Further, so that the stencil does not have “stickiness” with the layer of applied solution and is easily separated from it, it should be moistened with water - this can be done with a sponge or damp cloth. If the stencil is made of rubber, then you can simply dip it in a basin of water, but in this case you need to wait for the excess to drain, otherwise excess moisture can ruin the whole work.
After this, the stencil is pressed against the applied fresh plaster and carefully pressed so that the relief of the brickwork remains on it.
Next, the stencil is removed and applied further, next to the just pressed relief. Here you need to try and apply it so that the masonry is even and its horizontal seams do not become distorted.
When the relief has been applied to the entire surface, it is left until completely dry.
After drying, the wall should be completely covered with one color - usually chosen for this light shades, since it will be easiest to apply any color to them, as well as highlight dark shade or leave all masonry seams light.

Painting imitation brickwork is already creative process, so you can allow yourself various fantasies. In this case, of course, it is necessary to keep in mind that the chosen color will set the mood for the entire interior of the room.

Creating a brickwork relief using plaster and masking tape

For this technology of reproducing imitation brickwork on the wall, you will need the above-mentioned composition of cement plaster mortar and masking tape. Some craftsmen even use electrical tape, however, it does not adhere to the wall well, while high-quality masking tape has excellent adhesion to any surface.

The width of the tape should be no more than 14 mm, and if you couldn’t find tape of that width, you’ll have to buy a wider one and carefully cut it in half right in the skein. If its edges are not perfectly smooth, this is not a big deal at all, since this factor will not affect the accuracy of the relief, but rather will even play into your hands.

The first step is to mark the prepared surface of the wall to be tiled for brickwork.

Next, masking tape is glued along all the marked lines on the wall. It should be secured so that the edges of the horizontal pieces of tape extend beyond the edges of the surface being designed, and the solution should not be applied to them, and the vertical pieces should be well glued to the horizontal ones, always on top of them.
Then, on the surface of the wall, on top of the glued grid of adhesive tape, using a wide spatula, apply a solution with a layer thickness of 5-6 mm - the height of the relief will depend on this parameter. Do not apply too thick a layer, otherwise you will have to cover the seams with grout.
After applying the solution completely to the entire wall, you can walk over it with a damp rubber glove to create a textured surface. If you plan to leave the surface of the “bricks” flat, then you should not touch the mortar layer.

The most interesting stage in this method of simulating brickwork is removing the masking tape, since after this operation the relief of the wall will be immediately visible. Several strips of adhesive tape are picked up from one of the free sides and begin to be carefully peeled off from the wall, and as a result, in place of the peeled tape, seams are formed between the “ brick tiles" After removing the tape from the entire surface, the wall should be left until completely dry.

It is recommended to let the wall dry before painting - this operation will make the surface more pliable for the next stage - painting, since the paint will lie flat on the surface and will not be absorbed into the surface. plaster layer. Which shades to choose for the wall depends on the preference of the master.

Video: How to imitate brickwork using plaster and masking tape

From all of the above we can conclude that construction market has an excess various materials, ideally imitating brickwork or other stone surfaces. Sometimes the quality of the imitation is such that when finished, it is impossible to distinguish it from real brick by texture and color. Well, if ready-made tiles or panels do not fit into the family budget, then it is quite possible to use one of the more economical ways, and decorate the wall using affordable materials.

Currently, there is a wide variety of finishing materials, which are presented in a wide range and made from various materials.

Clinker bricks for interior decoration are in high consumer demand due to the large number of advantages and durability.

This decoration looks original not only in city apartments, but also in private ones. country houses.

This facing material is available in a wide range and has a large selection of shades and textures.

Thanks to different structure surfaces provide the opportunity to create an original and unique design of the premises.

Clay is used for making different varieties, therefore this material is environmentally friendly and safe for human health.

To obtain shades, only natural dyes without adding harmful chemicals.

A special production technology guarantees not only a long service life, but also preservation of the characteristics and color of the coating.

The coating can be smooth or rough, with small irregularities and protrusions.

Characteristic

The most popular type of finishing is clinker brick, the main component of which is clay.

It should be noted that the high cost is determined by the complexity of the technological process.

Firing the clay ultimately gives high strength and density to the coating, while the surface of the brick faces is smooth and the color of the brick is uneven.

Basically, clinker bricks are used to cover walls that are subject to sudden changes. temperature regime, as well as stoves and fireplaces.

English style. All walls are covered only in cases where finishing is carried out in spacious and large rooms decorated with ceramics, wood or metal.

Installation rules and features

At the initial stage you need to go on the floor and pick up best location depending on its shape and size.

The material can be attached directly to the walls using cement mortar or a special adhesive composition.

If installation is carried out on wooden walls, then you should prepare them first, namely install the frame and provide moisture insulation.

The work begins with the corner elements, and lastly they begin laying the horizontal rows.

There may be slight color variations in different batches, so this factor should be taken into account when purchasing finishing material.

Useful video