DIY Christmas tree made from plastic bottles step by step. DIY Christmas tree from a plastic bottle. How to make a Christmas tree from cotton pads at home with your own hands: master class with photos

Make a Christmas tree with your own hands, cheaply, cheerfully and, in addition, quickly? This is possible, especially if there is a little accumulation in your home. plastic containers- bottles or cups.

We present to your attention a double detailed master class: how to make an exclusive New Year’s structure with your own hands from recycled materials.

Master class 1: Christmas tree made from plastic bottles

We will need:

• plastic bottles of different sizes, from 0.3 to 3 liters. Preferably green;
• a wooden stick, the height of which is the same as our Christmas tree. The diameter of the stick should be slightly smaller than the diameter of the neck of the bottles;
• bottle cap;
• stationery knife;
• scissors.

Stage one:

Carefully cut off the bottom of all plastic bottles. Carefully, use a stationery knife - first you need to make a puncture in the wall, and only then saw around the circumference. If sawing with a knife seems difficult, then you can cut with scissors. We leave one large bottom - it will serve as a support on which the Christmas tree will rest. The remaining bottoms can be thrown away.

Stage two:

We cut bottles with sawn-off bottoms into strips 2-2.5 cm wide, naturally, without bringing the cut to the neck. As a result, we get a kind of plastic “flower”.

Stage three:

We cut each strip along the edge, leaving a distance of 0.5 mm between the cuts. These are our “needles”. This way we will be able to make the future Christmas tree “fluffy”. We bend each “needle” - the branches turn out “lush”.

Stage four:

We carefully string the branches onto a stick with our own hands - this is how the Christmas tree is assembled. Wider blanks (from larger-volume bottles) will naturally be at the base, and smaller ones (bottles of smaller capacity) will be at the top. We put the bottom of the bottle on a stick, this will be the base on which the tree rests. We screw the cap on top, you can hammer in a nail for strength.

Christmas tree made from plastic bottles is ready! Decorate! Tinsel, rain and simple matte balls will look great on such a unique New Year's beauty. A garland on an ascetic plastic tree can also look very stylish. Experiment!

Master class 2: how to make a Christmas tree from cups

The most difficult thing in this procedure is perhaps finding green cups.

We will need:

• plastic cups;
• stapler;
• glue;
• toys, balls for decorations.

Stage one:

We place eight cups in the first row with our own hands, in a semicircle. We fasten them with a stapler. Then we put the second row on top - already seven cups. We also fasten them with a stapler. And so on, each row is one glass less. The rows can be lightly glued together for reliability, and also secured with staples. The finished tree should be stable.

Stage two:

Place a toy or ball in each cup. You can drip a little glue so that they are securely fixed inside. By the way, if you have a special glue gun, great, it will help you discreetly attach toys to plastic.

The original Christmas tree made from plastic cups is ready! But if you think that this idea is not creative enough, then here are options for decorating or modifying such a structure with your own hands:

• You can lay out the cups not in a semicircle, but in a circle. Only in this case is it better to “plant” them on a base made of a cardboard cone. Such a tree will have an attractive “facade”, that is, it can be placed in the center of the room, while a semicircular one looks good when standing against the wall.
• If you make a small cut in the top of each cup, you can pass a ribbon through it, secure it with a knot, and hang the decoration on it.
• Macaroni bows painted with golden gouache will look great as decorations.
• You can place a garland inside a round Christmas tree made from cups. It will shine very beautifully through the plastic, and its top light bulb will perfectly replace the traditional star.

Today we bring to your attention the process of making a large holiday tree from simple green plastic bottles. This Christmas tree is collapsible, so it can have any number of tiers (you only need a longer “stem”). You can add more layers each year and within a few years you will get a big fluffy beauty around which your children will dance in circles.

To make a Christmas tree from plastic bottles you need:

Green plastic bottles (it took 1.3 liter bottles about 30 pieces);

Steel part (“rod”) of the desired length (here about 0.5 m, with an approximate diameter of 0.5 cm);

Single-core aluminum wire insulated (section 2.5mm2);

Christmas tree stands;

Scissors, heat gun;

Christmas tree made from plastic bottles step by step:

Take the bottle and cut off the middle part from it, as in photo 2-3. Then cut this part of the bottle in a spiral using scissors, cut a strip with an approximate width of about 2 centimeters (photo 4).

Next, you need to bend one edge approximately 0.5 cm along the entire length of the strip, as in photo 5-6. This side will help set the direction for spruce needles (needles), and will also serve as a limiter for cutting the “needles”. Cut a fringe strip about 0.1 cm wide (photo 7-8).

Then start creating spruce branches. Let's make a “top” for the Christmas tree, for which wrap a strip of plastic (about 8 cm long) around the “rod” and glue it using a hot-melt gun (apply glue to the “rod”, otherwise the workpiece will high temperature may become deformed) (photo 9). Next, twist a small piece of fringe and glue the pieces inside (photo 10). Then wrap the “rod” in a spiral with a strip of fringe (photo 11). When one strip ends, take another and continue gluing (photo 12-13).

After making the top, make the first tier of branches, which will consist of three short parts (a branch with an approximate length of about 7-8 cm). Make a wire frame, as shown in photo 14, connect it to a plastic ring (photo 15-16).

Start wrapping the “branches” in the same way as the top (photo 17). After creating all the branches, braid the “needles” and the main stem (photo 18-19). As a result, you should get two parts, as in photo 20.

Make the third detail of the future Christmas tree, a remote one. At first it was made too high, so it was moved to the bottom of the tree and the piece was made smaller. In total, four distances were used for this tree: Upper - approximately 0.5 cm; the second - about 0.6 cm; third - 7 cm; the lower one is 8 cm. Make “distances” by analogy with making the crown, just do not close the upper hole (photo 21). The Christmas tree will look at this stage as in photo 22.

Next, make a second tier of branches, which will be wider than the first and will already include four branches (with an approximate length of about 9 cm), each of which will have two side branches. The length of the main branches turned out to be approximately 9 cm (photo 23 -24).

Wrap the frame, starting with the smallest branches, then the main ones, and ending with the trunk (photo 25-26). Under the influence of hot glue, the plastic heats up and takes on a fairly plastic shape, making it very easy to set the direction of the needles for each branch at the junction of the branches (photos 27-29).

The central part of the stem before camouflage with pine needles looks like in photo 30, and after camouflage it looks like in photo 31. Next you need to make a second spacer part (photo 32).

Next comes the production of the third tier, with an approximate length of branches of about 10 cm (20 cm in diameter) (photo 33). Finally, make the lower tier (branches 15 cm long (30 cm in diameter)) and the lower distance (photo 34).

All that remains is to install everything on the stand! If desired, you can make any number of tiers, and each subsequent tier should be proportionally wider than the previous one - this way you can get a tall and elegant Christmas tree.

The Christmas tree made from plastic bottles is ready!

According to the site: girlsschool.ru

At the bottom there should be the largest bottles (2 and 1.5 liters, in the middle - liter bottles, and at the top 0.5 and 0.3 liter bottles. If you have bottles of the same volume, then adjust the length of the “branches” yourself by cutting stripes up required length.

Make a hole in the left bottom, which you secure to the lower end of the stick using a plastic bottle cap (you can hammer a nail in for strength).

Place the last, smallest piece, neck up, on the upper end of the stick and screw the green plug onto the neck, also securing it with a nail for strength.

A little patience, perseverance, effort and the forest beauty is ready!

Such Christmas trees can be used as New Year's decoration your houses!

Method 2. To make such a Christmas tree you need a minimum of time and expense. A master class on making a Christmas tree from plastic bottles will tell you in detail how to make such an original New Year's craft.

To make a decorative New Year's craft: a Christmas tree from plastic bottles, you will need the following:

1. Plastic bottles - 3 pcs;
2. Scotch;
3. Sheet thick paper, ideally whatman paper (A4);
4. Scissors;

Method 3. And finally last option for today - a Christmas tree made from plastic milk bottles (what decorative New Year trees are not made from...). The design is completely collapsible, has maximum resemblance to the original, does not require special complex technologies and specific work skills, there are no problems with bottles either, and a holiday is just around the corner...

Materials and tools

The material for making the Christmas tree is a milk plastic bottle or part of it (Fig. 1). To make a homemade tabletop Christmas tree, you will need 5-20 milk/kefir plastic bottles with corrugation at the bottom. The number of bottles determines the number of branches and tiers. The more branches, the more fluffy the Christmas tree is; the more tiers, the taller it is.

In addition to bottles, you only need scissors and plastic rivet technology

Plastic rivets

To implement the technology of plastic rivets, it is necessary to have a means for melting (installing) the rivets and the rivet itself. You need to manage to melt the head of the rivet using a hot nail or lighter. You can do this in the same way with a well-heated soldering iron. In addition, you will need clamps and tweezers to install rivets in hard-to-reach places.

For plastic rivets, it is very important to choose the material. After fumbling for about a year, through trial and error, taking into account the requirements of strength and availability, I identified several sources for obtaining plastic rivets:

1. Empty ballpoint pen refills. Enough available material. They are good because they are colorless and the compound, with their help, turns out to be organically integrated into the product made from plastic bottles. Such a rivet turns out neat, with a round head, however, it has a slightly reduced tensile strength. In addition, the rod from ballpoint pens is round in cross-section and completely fills the drilled hole in the parts being connected. By the way, the walls of the rods are different thicknesses, for rivets it is better to use rods with thicker walls.

2. Chupa Chups sticks. Similar to option No. 1 only in color. The connection is more cumbersome, and the rivet head melts with difficulty (it either burns, becomes ugly, or unreliable).

3. The most perfect option, and very convenient (I give the world a suggestion) to use material from buckets with construction mixtures for 3, 5, 10 liters There are quite a lot of them left after repairs, and even one lasts for a long time.

From the walls of such a bucket you need to cut a ring, and cut the ring along the generatrix (this is the only way) into strips 2...4 mm wide, length from 4 to 15 cm. These will be the blanks for rivets, and, moreover, the best and most affordable, in almost unlimited quantities quantity.

Obtaining a connection using such rivets is simple. It is more convenient for this to prepare rivets of the required length in advance, melting the head of the plastic rod on one side. To connect two parts with plastic rivets, we overlap the parts and melt them with the same burner, forming a hole. the desired profile and sizes, insert a rivet there and, by melting, form a head from the opposite end of the rivet rod. After practicing reflowing several times, the head turns out neat and tear-resistant.

Let's get started...

To implement the idea it is necessary raw material in the form of a part of a milk plastic bottle (Fig. 1a) which is cut along the circumference into two components (Fig. 2 and Fig. 3, respectively). A trunk will be formed from the part adjacent to the neck (Fig. 1b), and branches of the future New Year tree will be cut out from the ring with a central groove (Fig. 1c). One whole plastic bottle produces two or three rings. The more rings you prepare, the fluffier and taller the Christmas tree you can assemble. I had at least 20 of these rings (10 full bottles).

Plastic rings with a groove in the middle need to be cut into several equal parts(Fig. 2) along the generatrices of the bottle cylinder. As a result, we get convex rectangles. If you cut into 2 parts, then from such long halves you will get long lower branches of the Christmas tree, if you cut into 3 equal parts, you will get branches of medium tiers and medium length, and cutting into 4-5 parts, you get small blanks for the upper tiers of a tabletop Christmas tree . It is not at all necessary to observe particular uniformity in the dimensions of the rectangles for one type of tiers.

Next begins the rather tedious work of forming the branch. From each plastic convex rectangle (Fig. 3a), a wedge-shaped blank should be cut out with scissors (Fig. 3b). The axis of symmetry of the wedge-shaped part should be located along the corrugation groove. Immediately after cutting the workpiece, “needles” should be formed on it, making cuts along the side edges at approximately 45 degrees to the groove and radially at the end of the “branch”. (Fig. 3c). The needles are alternately moved out from the plane of the workpiece, also at 45 degrees to each other. Placing the needles up and down relative to the plane of the branch provides fluffiness to the Christmas tree.

As a result of such painstaking work, several sets (Fig. 4) of branches are obtained different sizes for desktop homemade Christmas tree. Cutting branches and then needles is quite a long task, but you can entrust this to your family as part of a collective creativity to decorate life under New Year. It should be noted that it is difficult to accurately determine the number of branches forming a specific tier by eye, so you should always have several rings in stock (Fig. 1c) for cutting branches during the installation of tiers

The place for attaching branches is the trunk, which consists of several parts (logs). The top parts of plastic bottles (Fig. 1b) were considered waste during the separation of the rings (Fig. 1c), but now they are also used in tree making to create a trunk. The base of the trunk and the lower log is the full neck part of a plastic bottle (Fig. 5a). The upper logs are assembled from blanks obtained by cutting off the threaded part of a milk bottle with a flange, as well as removing a segment of plastic along the generatrices (Fig. 5b, 5c). The segments need to be rolled into a tube and secured on both sides with plastic rivets. In a similar way, it is necessary to create several logs to attach tiers of branches. In my case, these are 3 logs, but there could be more or less. For a miniature Christmas tree, 3-4 tiers of branches on just one log are enough.

Naturally, the diameter of the trunk should taper towards the top of the tabletop tree and the diameter of the upper log should be smaller than the lower one. The larger the cut of the segment, the higher the log obtained from the conical top of the plastic bottle. For the top you need a half segment, and for the middle part about two-thirds of the whole neck (Fig. 5b). The diameter of the lower hole of the upper log should be approximately 1 mm larger than the upper hole of the lower log forming the trunk.

It's time to attach the branches to the "logs". Each log will need to place 2-3 tiers of branches. A small number of tiers does not allow you to effectively cover the heads of the rivets with branches, and a large number spoils the aesthetic appearance of the Christmas tree. In each tier of this design you can install from 4 to 10 branches. Fastening is carried out using plastic rivets, since you will need quite a lot of plastic rivets, it is better to prepare them for future use. The easiest way is to place the branches in tiers on the lower logs (Fig. 6), since the neck of the plastic bottle is wide enough and it is convenient to hold the plastic rivet with inside finger.

If you place the branches closely along the circumference of the tier, then one rivet is enough to attach the branch to the trunk (Fig. 6-8). For those who like greater reliability, they can install two rivets side by side. The tiers of branches must be formed like the roof deck of a house - from the bottom up, then the branches of the upper tier will cover the rivets of the lower one and the heads of the rivets will be completely invisible.

In my case, in the lower (Fig. 6) and middle (Fig. 7) log of the trunk there are 2 tiers of branches, and in the upper one - 3 (Fig. 8). There are 5 tiers of branches in total. It’s quite enough to look amazingly similar to a real tree. Installation of plastic rivets on the upper tier, due to its small diameter, should be done using tweezers or a medical clamp.

After securing all tiers to all logs, you can begin final assembly. But first it is advisable to decide on the top. In my case, without thinking for a long time, I built the top using the same technology as the trunk (Fig. 5), that is, by rolling the plastic into a cone. But you can do this in another way, for example, in the form of an asterisk or a ball (I like the cone better). The top of the tree is attached to the upper element of the trunk also using a rivet, installed from the inside and melted from the outside. Top part trunk, together with the top, already has a miniature tabletop Christmas tree itself (Fig. 9). You can install it on your monitor and enhance the holiday feeling...

A living Christmas tree grows from the bottom up, in the same order, and we collect logs with tiers of branches by adding “logs” (Fig. 10) to the already existing Christmas tree. It is better to connect the trunk elements together in a place covered by a branch, at three points along the circumference of the trunk. In this case, the trunk becomes rigid and will not break if the Christmas tree accidentally falls to the floor from the table, the Christmas tree is a tabletop one...

And if you insert a dynamic light part (for example, a garland) inside the Christmas tree, then New Year's Eve she will amaze those around her with her charm:

Here is such a master class. Of course, it’s a little complicated, but what a beauty it turns out!

A DIY Christmas tree made from plastic bottles can be a great surprise for the New Year and Christmas holidays. This article will describe various ways making such a craft.

Materials and tools

First, let's look at the materials and tools that will be needed in the process of making such a magnificent decoration as a Christmas tree made from plastic bottles with your own hands. This list includes the following items:

Plastic bottles. Preferably green: after all natural color Christmas trees - green. But any other is possible. In this case, you will have to purchase additional green paint and with its help properly design the final craft.

Stationery scissors and a knife for cutting plastic bottles.

Black marker for marking.

Glue and tape.

Wire.

Steel pipe.

Electric drill with drill bit.

• Cardboard or Whatman paper.

  Markers, pencils and paints.

Methods

There are several ways to make a Christmas tree with your own hands from plastic bottles. It could be:

Method one: big Christmas tree

This DIY Christmas tree made from plastic bottles is made from enough large quantity containers. Therefore, before starting work, it is necessary to collect an impressive supply of such bottles. There are two ways to create such a craft. The first of them consists of the following sequence:

We take a metal pipe of the required length and install it in the ground at the place where the Christmas tree is collected using a hammer.

Then, step by step, around this pipe we make circles of the “lower tier of the tree” from plastic bottles that fit tightly to each other. We fix them with tape.

Similarly, we create the next tiers of our tree and fix them using tape. We also take into account that with each subsequent tier the diameter of the formed circle decreases. That is, you should get a cone that looks like a New Year's beauty.

Most upper tier The Christmas tree should consist of only one bottle, mounted on a metal pipe.

Then you need to decorate the tree properly.

The key disadvantage of this method is that the New Year's beauty turns out to be motionless. Not everyone likes it. Therefore, some craftsmen use the second method, which consists of the following steps:

As in the previous case, we install the central load-bearing frame from metal pipe using a hammer at the place where the craft is created.

Using electric drill We drill holes in the pipe at the level of each tier of the tree.

IN drilled holes We install a straight wire, the length of which is equal to the diameter of the tier. Then we make a circle from the same wire. Again, the diameter of each is more than high level is reduced so that the end result is a cone.

We make the upper part from a single plastic bottle, which we put on the free end of a metal pipe.

Then we make a hole in the cap of each bottle into which we install a wire hook, which is then fixed on the ring.

Filling each of the tiers of the tree, we get final result- New Year's beauty.

At the next stage we decorate the Christmas tree.

Unlike the first case, here the bottles hang on a ring and can move.

Option two: a small Christmas tree on the table

You don't always need a big one Christmas tree from plastic bottles, as in the previous case. Then you can make a miniature beauty from a green plastic container with a capacity of 2 liters. The algorithm for making a Christmas tree in this case is as follows:

We retreat about 3 cm from the bottom of the neck of the bottle and use a stationery knife to cut off its upper part.

Then we roll up a sheet of whatman paper and place it in the neck. We fix this entire structure with tape. The frame of the Christmas tree is ready.

At the next stage, cut off the bottom of the container, and cut the rest into rings 3-4 cm wide.

Then we cut the bottom of each ring into thin strips, but leave the top untouched. After this, we cut the ring itself into 2 equal parts and screw it to whatman paper. Don't forget to use tape to secure it. So, step by step, we turn whatman paper into green branches and get a miniature New Year's beauty. We leave the top of the tree sharp and fix it with the same tape.

Another way

In the form of a three-dimensional applique, you can make a Christmas tree from plastic bottles with your own hands (photos of some crafts, by the way, are presented in the review). In this case, we take a sheet of cardboard or whatman paper as a basis. required sizes. Then we take 3-4 plastic bottles and mark them in the form of a three-dimensional model of a Christmas tree. For example, these could be triangles or trapezoids. Using stationery scissors and a knife, cut according to the markings of the model. Then we glue them to the base with glue. Then we properly design a sheet of cardboard or whatman paper. When finished, you can add a frame to this craft, and it will become an excellent decoration for your home.

Decorating the craft

Any christmas tree made from a plastic bottle, made with your own hands, must be decorated at the final stage. For these purposes, you can also use the usual glass toys, and garlands, and other available materials. In general, we do not limit the flight of imagination and use everything we deem necessary.

Summary

This article describes three main ways to make a Christmas tree from plastic bottles with your own hands. Each of them is strictly suitable for one specific situation. The simplest is the last, third, which allows you to create a three-dimensional image of a Christmas tree. The most difficult is the first one. It requires a lot of material and is not that easy to implement.

Do you think it’s impossible to make a Christmas tree with your own hands from an ordinary plastic bottle? But no! And now we will prove it to you. By the way, such a New Year’s tree looks quite decent and very cute! A plastic Christmas tree can be placed anywhere: at least on the kitchen window, at least on the bedside table near the TV, or at least on the children's shelf next to toys and books. So, let's get to it?!

Materials and tools for.

To make a beautiful Christmas tree we will need:
one regular 2 liter plastic bottle, green;
landscape sheet of A4 format;
adhesive tape(scotch);
scissors.

Agree, it’s very nice that there is absolutely no glue! How to make a Christmas tree from a plastic bottle. Even a junior high school student can cope with the task, let alone an adult who can make plastic Christmas tree it won't be difficult!
1. Cut off the neck of the bottle so that you get a stand for the tree.

2. From a landscape sheet you need to twist a tree trunk into a cone. The diameter of the tube will correspond to the diameter of the bottle neck. Place the handset into the cradle.

3. Now cut nine of these plates. Features of these blanks: 3 pcs. do rectangular shape size 8 cm by 7 cm; next 3 pcs. – 8 cm by 5.5 cm; the last 3 plates are 6 cm by 4 cm. It is not necessary to maintain the size in numbers, but the proportions of the workpieces must be observed: large pieces, medium and small.

5. To make the branches lush, you need to twist them slightly: take the knife with the blunt side up and stretch it along the strip, pressing the blade firmly against the ribbons. There is no need to twist all the strips at once, this is difficult and ineffective. Take 4-5 ribbons.

6. Now you need to attach the needles to the paper trunk. To do this, we wrap it in plates, starting from the base. Using tape we secure each tier of needles. In the same way we move to the top.