Facade panels for exterior finishing of houses fineber. Fineber façade panels are the best choice for home decoration. Installation of FineBear facade panels

Fineber facade panels are designed for finishing external walls of buildings, concrete fences, retaining walls and other structures. Basement siding not only makes the walls look like stone or brickwork, but also protects them from wind, dirt and precipitation.

Design of Fineber facade panels

The panel is made of durable polypropylene with additives that increase the resistance of the plastic to ultraviolet radiation, some chemical substances and temperature changes. The thickness of the panel is about 3 mm (it is slightly thicker on the stiffeners).

The front side of the facade panel has relief surface. The relief imitates stone or brickwork. Accuracy of imitation is achieved through multi-layer painting, which reproduces the smallest details- down to pores, microcracks and efflorescence.

For fastening to the sheathing on the top and bottom sides The Fainbear basement siding panels have rows of holes made. There are protrusions and recesses on the side walls that make horizontal joining easier.

Elements for wall decoration

• row panel;
• outer corner;
• additional elements (starting strip, J-profile, strip for fastening the internal corner).

Features of installation of Fainbir basement siding

Care

Properly secured plinth Fineber siding can last for several decades without requiring any maintenance. If necessary, you can clean the panels from dust and dirt with a stream of water from a hose.

Facade panels can be various forms, colors, textures, sizes, but they all perform the main functions: protecting walls from damage and external influences, decorative design facade of the building.

Decorative panels are attached to the sheathing. They are a ventilated façade structure. Each manufacturer's material has distinctive features by quality, texture, collection of colors, fastening of elements.

Popular manufacturer of façade hanging structures is the company FineBer.

FineBear panels for exterior finishing Houses are products Russian manufacturer"Terna Polymer". The plant has been specializing in the production of such materials for many years: it has high-tech equipment, and specialists have undergone additional training before working on specialized machines.

Sheets for cladding are produced by casting, during which the material is pressed under high temperature. Then it is applied to the surface paintwork. Thanks to this technology, the strength of the products is ensured.

Since the manufacturer is domestic, it has the opportunity to reduce the cost of products due to the absence of customs costs. The cost of FineBear coating is lower than foreign ones, which does not in any way affect the quality of the products.

In addition to ordinary panel elements, FineBir has components for each type. Additional elements contribute to the formation of completeness of the cladding and decorative effect.

FineBir panels are quite light, their weight does not exceed 2-3 kilograms, which does not require additional reinforcement of the foundation part of the structure.

Advantages and disadvantages of panels

FineBir strives to constantly improve the quality of its products. This is due to great competition and the desire to implement new technologies in production.

Like any facade material, FineBir has certain advantages:

• adapting the material to domestic ones climatic conditions, which is typical for a wide range of temperature differences;
• long operational period;
• Thanks to the strong locking elements and the simplicity of the assembly of the structure, sufficient quick installation designs;
• decorative features. The manufacturer gives preference to a textured design similar to facing brick or stone;
• due to the lightness of the material, no load is created on the supporting structure;
• moisture resistance of the coating ensured by the presence of strong locking fastenings;
• due to polymer coating there is absolutely no possibility of mold and mildew forming on the surface;
• the cost of FineBir is lower than its analogues;
• no casing required special care: capable of self-cleaning under the influence of rain flows;
• the material is fireproof, which is confirmed by test reports.

In addition, the coating with FineBir facade panels is quite durable and wear-resistant.

The disadvantages of FineBear cladding panels include significant expansion of the material when temperature fluctuations, which determines the fastening of the panels to ensure a temperature gap.

Despite the manufacturer's stated ability to withstand ultraviolet irradiation, the panels can fade over time, especially if the front part is on the sunny side.

The ability of the panel to break upon impact determines careful transportation and careful installation of products.

This factor does not directly relate to qualitative deficiencies facade material, but it should be taken into account when delivering the material and working with it.

Specifications

Facade elements produced by FineBir have the following technical indicators:

• the length of one panel is from 1,080 to 1,137 m (each collection has its own indicators);
• width - from 447 to 470 mm;
• coverage area (depending on size) - from 0.4 m² to 0.46 m²;
• the weight of one main element (panel) is from 2.04 kg to 2.78 kg.

FineBir products are certified and have appropriate certificates of conformity. In addition, test reports confirm the conduct of research into the influence of various external factors on the material.

Types of FineBear panels

The range of Fainbeer façade elements is gradually increasing in connection with market needs. The variety of collections allows even the most demanding buyer to choose a coating.

FineBir has the following types facade panels:

• collection "Brick". Is an artificial analogue brickwork from point of view visual design. Imitation of brickwork implies the presence of five shades of natural brick with a texture identical to brickwork: beige, white coated, red, fired red, burnt. The working elements of the collection have dimensions of 1.137 x 0.47 m;
• collection “Facing brick”. Characterized by the presence of a glossy front side, characteristic of facing bricks. The surface coating is smooth, the collection includes elements of three shades: yellow, ceramic red, burnt. The main elements of the coating have dimensions of 1.130x0.463 m;
• Britt Brick collection. A special feature of this type is the coloring of the elements in the form of brickwork with a contrasting frame for each brick. For example, burgundy brick has a white edge. The collection features darkened colors: black-brown, burgundy, maroon and dark pink. The size of the panels in this collection corresponds to 1.130x0.463 m;
• collection "Stone". The cladding has an external resemblance to masonry. The texture is presented in full accordance with natural material. This collection includes elements in beige, coated white, brown, terracotta and gray-green. Panel dimensions 1.137x0.470 m;
• collection "Wild Stone". Imitation of natural stone. The color range is presented in the following shades: sand, coated white, terracotta, pearl, gray-green. The elements have dimensions of 1.117 x 0.463 m;
• collection “Large stone”. The pattern of the panels imitates a larger natural stone, the collection itself is presented in colors the same as in the “Wild Stone” series, with the exception of pearl. Panel size 1,080x452 m;
• collection “Natural stone”. It has a texture similar to natural stone and is distinguished by a wide variety of colors: sand, quartz, red-brown, pearl, brown, gray-brown. Panel size 1.085x0.447 m;
• collection "Rock". This texture imitates natural rocky stone in relief and pattern. The collection is presented in various color options: terracotta, sand, beige, yellow-brown, coated white. Element dimensions 1.094x0.459 m;
• collection "Slate". Imitation flat slate accurately replicates natural slate stone. The elements are characterized by natural shades: terracotta, beige, sand, white coated. Panel dimensions are 1.137 x 0.47 m.
• collection “Russian Fortress”. Ceramic variety material.

Facade elements accurately imitate natural materials, repeating not only the texture pattern, but also bulges and irregularities natural material. All collections are supplied with ten slabs in a protected packaging container.

Preparing the wall for installation of panels

Installation of panels includes three types of work: preparation of walls for cladding, installation of sheathing, installation of facade panels and additional elements.

Wall preparation is no less an important condition ensuring reliable and high-quality cladding facade.

To protect walls from corrosion and moisture, it is necessary to seal seams, cracks, and also clean them from dust and debris. To prevent the formation of mold and mildew on the walls, it is advisable to treat them with an antiseptic primer.

It is important to check the horizontal and vertical positions of the walls using a level, since the facing coating requires strict indicators. If there are small deviations (up to several centimeters), they can be corrected using lathing.

Installation of FineBear facade panels

The façade elements are fastened to the lathing.

You can make the frame using wooden beams or metal profile . Wooden elements Before installation, it should be thoroughly dried and treated with moisture-resistant and antiseptic agents.

It is recommended that the sheathing step be carried out along the length of the panel (with vertical sheathing) or height (with horizontal guides). The manufacturer recommends installing additional guides that run through the center of the panel to ensure maximum rigidity of the coating.

The profile should be secured around all openings. At the internal and external corners it is necessary to install additional slats in accordance with the width of the element.

NOTE!

When installing the frame, you should check the plane of the surface using a level.

After installing the frame, the façade elements should be attached in the following sequence:

• installation of horizontal starting bar . The distance from the corner should be 30 cm. Interrupting the strip at 3 cm will ensure expansion during temperature fluctuations. The strip line is installed around the entire perimeter;
• installation external corners . The corner should be inserted into the starting line and secured in the top holes, and then secured in the remaining holes, observing the principle of thermal expansion (with a gap). If you need to increase corner element, then it should be overlapped by 30 mm;
• installation of working panels. The panels should be inserted into the starting strip and between each other using locking elements. The last panel, if necessary, is cut strictly perpendicular;
• installation of internal corners. Additional elements to the collection in the form of internal corners are universal. They should be attached to the sheathing and joined to the working panels in grooves;
• window decoration and doorways should be done using a J-profile. The same profile can be used when finishing coatings;
• installation of additional components. To attach additional elements, you can make corresponding holes, similar to those in the factory elements.

The installation process is not labor-intensive, the structure is assembled quickly. The manufacturer FineBir recommends installing panels at a temperature of at least 10°C.

By covering the façade with FineBear panels, it is possible to ensure the protection of the walls, the decorative and aesthetic appeal of the building.

Useful video

Video installation instructions facade cladding Fineber:

In contact with

DIGA offers for sale FineBer facade panels - a reliable domestic manufacturer who relied on product quality. FineBer plinth panels for suburban construction under brick, natural stone and slate are available in a wide range color scheme and with a large selection of textures.

Renew the facade and enhance the appearance of your home - buy FineBer facade panels

The range of FineBer facade panels includes 9 collections, and progressive improvement and technological capabilities allow the manufacturer to delight customers with new possibilities for decorating products every year. By the way, you can buy vinyl siding from us at the most favorable conditions, considering that we cooperate directly with manufacturers.

What benefits do I get by purchasing plinth panels FineBer

1. The texture and colors are as close to natural as possible, which allows you to create the full effect of a house made of natural stone.
2. For the production of products, environmentally friendly raw materials are used - polypropylene (safe and harmless material).
3. The product is heat and moisture resistant, indifferent to mechanical damage and UV action.
4. Easy installation due to convenient system fastenings and light specific gravity designs.
5. Long service life - about 50 years.
6. Easy to maintain - just wash the panels with a stream of water.
7. The product has proven itself reliably in the harsh conditions of the Russian climate.

• for cladding the facade of a building;
• for cladding individual parts building.

The products can be installed on any base - brick, concrete, wood.

FineBer will help you choose and purchase facade panels in the online store detailed information by dimensions, prices, colors, weight and other characteristics in the product card. Delivery in Moscow and Moscow Region is carried out by transport with a carrying capacity of up to 15 tons. The terms and conditions of delivery to the regions are negotiated individually.

• Length: 1085 mm
• Width: 447 mm
• Coverage area: 0.4 m2
• Packaging: 10 pcs.

• Slate
• Rock
• Large stone
• Natural stone
• Brick
• Facing brick

The unique properties of FineBer façade panels allow them to be at the peak of attractiveness among existing ones facing materials. Along with the practicality inherent artificial surfaces, FineBer panels have important property- they naturally convey the surface natural materials. More and more owners country houses give preference to facade panels, since this is the most advantageous and economical way give the home a fresh and natural look. Made by casting, the panels are perfect for continuous cladding of the facade and finishing of the base.

Many years of experience in developing and improving FineBer facade panels allowed us to achieve highest quality products that are as close as possible to the texture of natural materials. The current range of façade panels is represented by 9 series: “Brick”, “Facing brick”, “Britt facing brick”, “Stone”, “Wild stone”, “Natural stone”, “Large stone”, “Rock”, “Slate” " FineBer is continuously developing its range: every year offering customers new decors and series of facade panels.

Thanks to their special texture, which is as close as possible to natural even to the touch, FineBer panels visually create the feeling of natural stone or brickwork. Relief, rough coating and natural colors provide one hundred percent effect natural stone or brick. Modern, environmentally friendly and safe material The polypropylene from which the panels are made provides high resistance to temperature changes. The panels tolerate excess moisture well and are resistant to direct sunlight.

Ease of installation and ease of maintenance complement beneficial features FineBer facade panels. When installing them, you can avoid “wet” work thanks to a well-thought-out fastening system and accessories. An accessory has been developed specifically for FineBer façade panels. internal corner" When installing facade panels, you no longer need to think about how to hide the gap at the junction of the walls - the internal corner of FineBer effectively closes the empty space. The “outer corner” accessory repeats the texture and color of the panel. Using the "outer corner" you can create separate decorative elements on the facade of the house.

FineBer facade panels are fully adapted to the conditions of the Russian climate. Easy to care for and designed for long-term use.

Facade panels are the fastest and most affordable way to update your appearance country house, make it attractive and natural. The SimpleBuild online store offers you a wide range of FineBer products. Facade panels of the FineBir brand are made by casting and can be used both for wall cladding and for finishing the base.

Why FineBer panels are attractive

A wide range of

Currently façade cladding panels FineBer is available in nine series with original decors, close to the textures of natural materials. This allows each buyer to choose an option that suits his tastes, as well as architectural style buildings and the surrounding landscape. The range of FainBer facade panels is constantly expanding and adding new products.

Special texture

It allows you to convey with maximum accuracy the color and features of the natural surface of natural finishing material: untreated natural stone, slate, uneven rock, neat brickwork. The polypropylene from which the facade panels are made is resistant to negative external influences - temperature changes, high humidity, sun rays.

Ease of installation

All FineBer panels have a well-thought-out system of fastenings and accessories, which makes their installation quick and simple, and also eliminates the need for “wet” work. To mask the gap at the junction of the walls, an “internal corner” detail was developed specifically for FineBir facade panels.

To buy FineBer panels in the SB online store, use the “Cart”. You can contact our managers by phone or by ordering a call back from the website.