• Pencil;
• Roulette;
• Folding meter;
• Beating;
• Knife with a straight blade;
• Knife with a hook-shaped blade;
• Hammer;
• Construction pistol;
• Spatula for mastic;
• Thermal construction hair dryer;
• Metal scissors;
• Screwdriver.

Installation of insulation

Installation of aprons

Installation of a drainage system

Roof waterproofing

Valley device

Pigtail installation method

Installation of tiles

Ventilation elements

Installation of a ventilation ridge

Installation of the “Special” aerator

Installation of pass-through elements

Installation of a roof window

Installation of the cap on the pipe

Installation of snow guards

Features of work

see also

Installation of the TEGOLA roofing system

Installation of the TEGOLA roofing system

A reliable roof is not only tiles, but also other correctly selected, compatible and correctly installed components and materials.

Any roof starts with truss structure, compliance building codes at this stage the key to the longevity of the roof. Rafter system must be installed with all design requirements for bearing capacity building structures. The most commonly used wooden rafters are 150x50 cm, installed at 60 cm intervals. It is very important that everything wooden elements were treated with special compounds that protect the structure from moisture, biodamage and fire.

Tools for installing roofing:

• Pencil;
• Roulette;
• Folding meter;
• Beating;
• Knife with a straight blade;
• Knife with a hook-shaped blade;
• Hammer;
• Construction pistol;
• Spatula for mastic;
• Thermal construction hair dryer;
• Metal scissors;
• Screwdriver.

Installation of a vapor barrier membrane

Vapor barrier prevents the penetration of warm vapors humid air from the living space into the roof structure, protecting the insulation and roof base from moisture.

We install a vapor barrier from the inside of the room on the inside of the insulation, according to the principle of materials on water. Roll out the roll parallel to the cornice, starting from the ridge.

We lay the vapor barrier with an overlap of 10–15 cm, with the metallized side facing the room.

It is very important to ensure that the membrane overlaps the wall. Fixation is carried out using a construction stapler, and the joints and overlaps on structural elements are carefully sealed with a special metallized tape.

Installation of insulation

Installing insulation allows you to ensure the necessary thermal conditions inside the building and prevent heat loss from the living space. Before laying the insulation, we form a rough lining inside the room; to insulate the roof slopes, use mineral wool slabs, the layer thickness for the central region of Russia is 20 cm. This figure depends on climate zone and may vary depending on conditions environment and the territorial location of the facility. We lay thermal insulation slabs into the body of the rafters in several layers with vertical seams staggered, closely avoiding the formation of cracks, so that the total layer is 15 cm.

Installation of vapor diffusion membrane

The vapor diffusion membrane protects the insulation from moisture and dust, while not preventing water pores from escaping into the external environment. We lay the membrane directly on the insulation, roll out the roll along the eaves, in parallel with an overlap of 10-15 cm. It is necessary to ensure that the membrane extends 15-20 cm beyond the insulation counter of the building. We fix the vapor diffusion layer with a construction stapler; to achieve the best result, the overlaps can be glued with a special self-adhesive tape.

Ventilation chamber design

In order for the roof to last a long time, it is necessary to ensure effective ventilation under-roof space, it helps remove water vapor coming from inside the room and equalizes the temperature over the entire surface of the roof. To ensure ventilation of the attic it is necessary to do air gap at least 5 cm between the insulation and the base of the roof. To do this, parallel to the rafters, we install a second row of counter beams with a cross-section of 50*50 mm, in increments of 30 cm. Along the eaves and the upper part of the roof, we provide inlet openings; for this purpose, in the bars after 1.5-2 meters, in a checkerboard pattern, we make gaps of 5- 10 cm.

Solid base device

The base for flexible tiles is made from oriented particle board or plywood with increased moisture resistance of at least 9 mm, the base must be smooth, dry and clean. When installing the base of the roof, we lay the slabs at intervals with gaps of -34 mm. To compensate for expansion. We lay the sheets parallel to the cornice; the height differences between the plates should not exceed 2 mm.

Installation of aprons

We attach the aprons to a solid base with a 2-3 cm offset; we use self-tapping screws for the job. The aprons are fixed in increments of 25-30 cm and with an overlap, which is treated with sealant.

Installation of a drainage system

We begin the drainage system by attaching the gutter hooks to ensure the movement of water; we give the gutter a slope of at least 2 mm per linear meter. Therefore, before bending and installing the hooks, we apply markings on them taking into account the slope of the gutter.

We start by installing the smallest and largest hook. The installation pitch of the hooks is 60 cm for steel and 30 cm for copper gutter. We recommend cutting the gutter hooks into the base and securing them with self-tapping screws. Before installing the gutter in it in accordance with the design, using a hacksaw or metal scissors, we cut a hole for the funnels, then we install the prepared gutter in the hooks and install a drip apron along the eaves above the gutter. To fasten elements of gutters, we use gutter connectors with a rubber seal, which maintains the tightness of the joints and compensates for possible expansion of the metal. We close the ends of the gutters with plugs. The installation of the funnel is carried out after installing the gutter in the hooks, moving from the gutter funnel to the drainpipe using two universal elbows, and installing a pipe outlet at the bottom of the drain riser. Drainpipes We place it at a distance of two to three centimeters from the wall and fasten it using a special kit (clamp with hardware and decorative overlay). The distance between the clamps should be no more than two meters.

Roof waterproofing

For additional waterproofing of the roof base, it is necessary to use rolled lining materials, which are laid over the entire surface of the roof, with a slope of up to 30 degrees, and partially with a slope of more than 30 degrees. For partial installation, we install waterproofing in the valleys, along the eaves and in places adjacent to pipes, ventilation shafts and windows. There is also an option for combined roof waterproofing, if the length of the slopes is more than 9 m, we measure 7 m from the beginning of the ridge and install waterproofing on the remaining section of the roof, as well as in the areas where the valleys adjoin, etc. We roll out the waterproofing roll parallel to the cornice, from the cornice to the ridge with a transverse overlap of 20 cm and a longitudinal overlap of 10 cm. We seal the overlaps bitumen mastic.

Valley device

When laying the waterproofing layer, it is provided protective layer at least 50 cm wide, laid in the valley. There are several ways to install roof tiles in a valley.

Pigtail installation method

For installation using the pigtail method, all important conditions must be met.

Equal slope of both slopes, while simultaneously laying the tiles on two slopes and cutting them to the opposite slope. A more common method of installing a valley is undercutting. Initially, we lay the tiles on a slope that has a smaller slope and length. To do this, on the adjacent slope we beat off a line parallel to the axis of the valley. And we place each row of tiles behind the valley onto the adjacent slope. Cutting along the previously marked line.

The important point of the valley zone is not pierced with nails, and lies 30 cm in each direction from its axis; the petals of the tiles lying in the valley are cut at an angle of 60 degrees to ensure water release. Then we proceed to laying the tiles on the adjacent slope. Having a large length and slope. To begin with, we beat off a line parallel to the axis of the valley on the slope, at a distance of 5-10 cm from it. We begin laying the tiles by placing each sheet on the adjacent slope and cutting the tiles along the marked line. When performing trimming, it is necessary to pin the plywood. We also cut the upper corners of the tiles located in the valley at an angle of 60 degrees to ensure water drainage.

Roof marking. When marking the roof, it is necessary to measure its actual dimensions, the angle of inclination, the position of the ribs and valleys relative to each other.

First, let's determine the location for the base horizontal axis; as a rule, this line is located in the widest part of the slope and parallel to the ridge line. We apply the line using coated padding. We select point A as the middle of the line. Mark points B and C at an equal distance to the left and right, about 1.5 m each. Then, at a distance equal to two meters from points B and C, we find the position of point D. By connecting points A and D, we get a line perpendicular line of the basic horizontal axis. In relation to these lines, we apply horizontal and vertical markings; the distance between the lines is dictated by the selected tile model; more detailed instructions are on each package.

Installation of tiles

After marking the tiles, installation can begin. Shingles are used to form the initial row. Trim the petals at the cutout points. In this case, we place the lower edge of the initial row at a distance of no more than 1 cm from the edge of the eaves overhang. We lay the initial row on both sides of the control vertical line. We fix the tile sheets with nails along the top edge and bitumen mastic along bottom edge. Next, we lay the rest next to the tiles in accordance with the instructions for a particular model. We fasten flexible tiles with rough roofing nails 25-35 mm long with a diameter of at least 3 mm and a head diameter of at least 9 mm. Roof tiles with metal coating fastened with stainless steel nails.

We fasten each shingle with 4 nails so that the nail also penetrates the upper edge of the underlying sheet of tile. When laying tiles on slopes with a slope of more than 60 degrees, the upper corners of the shingles must be secured with two additional nails.

We cut the ridge elements directly from the tiles, laying the ridge elements in the preferred direction of the wind. We lay the elements overlapping and fix each element with two nails, and also seal it with bitumen mastic. For the best fit and flexibility, bottom side ridge element, we recommend heating it with a heat gun.

Ventilation elements

Ventilation elements are represented by aerators, ventilation grilles, tower caps, and a ventilation ridge.

Installation of a ventilation ridge

To install a ventilation ridge, we do not bring the base of the roof to its line, leaving a width of 10 cm. Then we install bars with a cross-section of 50*50 cm in increments of 30 cm along it in a checkerboard pattern or across it. We install the apron and attach the insect net. We install OSB or plywood with increased moisture resistance on the bars, then we cover the ends of the resulting small slopes from OSB or plywood with an apron and cover the entire surface with tiles.

Installation of the “Special” aerator

Installed on slopes with a slope of 20 to 60 degrees. We begin the installation of the aerator by cutting a solid hole, which we cover with an insect net. We apply bitumen mastic around the perimeter of the hole and install an aerator, which we fix with nails. We treat the upper and side soles of the aerator body with mastic and cover them with a sheet of tiles with pre-cut holes. We complete the installation of the aerator by fixing the cover.

Installation of pass-through elements

When installing pass-through elements on finished roof We make the markings using the included paper template. Using the markings made, we cut out the tiles and make a hole in the solid base. Cover the hole with insect netting. We coat the pass-through element on the reverse side with bitumen mastic and fasten it in ready-made places with self-tapping screws. Finally we install ventilation pipes, passage elements can also be installed during the installation of tiles.

Connection to a wall or pipe

The connection of the roof to a pipe or wall can be done using the principle of insertion or overlay.

In the first case, the “cutting principle” of the abutment surface is to make a groove 2 cm deep, fill it with sealant, where we place the upper wall apron. The lower corner apron can be mounted both on the tiles and on it, observing the installation principle “On water”.

All joints between the apron and the wall are treated with silicone sealant.

When installing according to the overlay principle, we attach the top apron directly to the wall or pipe using a self-tapping screw with a dowel and a protective cap. It is also possible to design the junction using a single apron. In this case waterproofing membrane and place the tiles 20-30 cm on the wall and cover the upper edge of the materials with an apron on top.

Installation of a roof window

When creating a hole for installing a roof window, it is important to take into account that there should be a row of unedged tiles above the window. Installation is carried out in accordance with the manufacturer's requirements. From the outside around window box, fix the waterproofing layer. On the top and side flashings, we fix the tiles on top and install the lower flashing on the tiles, maintaining the principle of installation over water.

Installation of the cap on the pipe

We install an apron pre-riveted and assembled into a box onto the pipe. Pencil on the surface of the pipe through drilled holes we make serifs. Next, in the upper plane of the pipe, following the marks, we drill holes for the anchors and install them under them. Then we install the box on the pipe and the hood cover with brackets on it. We align the holes in the brackets with the holes in the box and secure the cap with bolts.

Hemming of eaves and front overhangs

Hemming of gable and eaves overhangs usually performed using perforated soffits. Which provide an unimpeded flow of air into the under-roof space and also help create a finished look for the overhang.

Installation of snow guards

Snow guards prevent an avalanche-like discharge of snow, protect the drainage system, the facade of the building, as well as the property of the owners from possible damage when the snow melts. Depending on the Tegola tile model and the slope of the roof slope, there are several options for installing a snow retention system.

Replacing a damaged roof section

If fragments of flexible tiles are damaged, it is very easy to replace a separate section.

To do this using construction hair dryer, heat it up, and then bend the tile petals located around the damage. Using a knife, cut out the damaged part. We cut out a new fragment from the new shingle, apply mastic, and mount the new fragment, securing it with two nails. We return the bent petals to their place, pressing them to the surface. Installation instructions

Every Tegola product comes with detailed instructions installation, but professional technical group, is ready to give full advice on all issues.

Features of work

There are several features when working with metal-coated tiles, which require special attention. The average daily temperature for laying tiles should be at least +10 degrees. For tiles with a metal coating, we use special rough nails made of stainless steel, with a head diameter of at least 9 mm. To avoid damage to the tiles on all roof surfaces, we install a snow retention system; it is recommended to move around the material only in shoes with soft rubber soles, and to perform all work with gloves.

For tiles with basalt granulate, minimum temperature regime-10 degrees.

Flexible tiles Tagola is a high-quality, technologically reliable roofing material that has received recognition in 70 countries on 5 continents.

Unique Tegola technologies will help make your home special and cozy.

The birth of a legend. Soft tiles Tegola

This video demonstrates the process of originating the idea of ​​​​creating Tegola flexible tiles.

A unique approach to the creation of flexible tiles made it possible to extend their service life roofing material, preserving for a long time all its most important protective properties. Tegola tiles are a reliable material for any climatic conditions.

Soft tiles Tegola in the Construction program

In this video, leading specialist of Tegola company Stanislav Bazarnov, together with the host of the “Construction” program, Alexander Rulev, will talk about the advantages, properties and installation process of Tegola flexible tiles.

Thanks to a new approach to creating a bitumen base, Tegola flexible tiles are able to withstand both high and low temperatures in any region of Russia. Tegola flexible tiles will suit almost any roofing surface thanks to the easy and fairly quick installation process.

Tegola Antik tiles | Tegola Antik can be easily and quickly installed on the roof and provides long-lasting protection for the building, as it has unique properties of resistance to any weather conditions. It is not afraid of ice or moisture and remains flexible even under the most severe frosts, neutral to temperature changes.

Top layer of Tegola Antik roofing tiles | Tegola Antique - ceramicized (painted with high temperatures) basalt crumb granules of three fractions; thanks to unique granulate production technology upper layer does not fade under influence sunlight and maintains the saturation of shades throughout the entire life of the roof.

Antique tiles have a special rounded shape - in the form of an oval. This design creates a feeling of antiquity, an image of a roof in the spirit of classical traditions. The color range includes 5 colors.

Color range of Tegola Antique series

Antique flexible tiles are simple and easy to install. Thanks to technical recommendations and the rules indicated on the packaging, installation of Antique does not require special professional skills. In addition, self-adhesive dots applied to the material during its production process greatly simplify work on the roof when laying Antique; at the same time, increased resistance of the material to wind loads is guaranteed. The thoughtful placement of self-adhesive dots (exactly under the tile blades) helps make the roof particularly attractive from an aesthetic point of view.

Storage and transportation Antique

Environmentally friendly and lightweight sheets of Antique tiles are packaged in convenient standard packs. Each of them contains the amount of material necessary to cover a roof area of ​​3.5 square meters.

Thanks to economical and safe packaging, Antique tiles are not damaged during transportation, and during storage they take up little space both in the warehouse and on the construction site. By observing the storage conditions indicated on the packaging, you can be sure that the quality of Antique will remain unchanged and the material will not lose its unique consumer properties.

Antique - this is your chance!

Antique flexible tiles can be used in any climatic and environmental conditions; she is not afraid of the effects of such atmospheric phenomena as snow, hail, wind, rain;

She's not afraid of anything ultraviolet radiation, nor sharp changes temperature.

It retains bright, rich color for many decades.

Antique is your chance to create a unique image modern building with the help of a reliable, beautiful and durable roof.

Antique tiles are distinguished by their scaly shape, which allows them to be used with particular efficiency in complex architectural projects, when, in the presence of curved shapes and various slopes, the problem of conveying the nuances of the roof configuration arises. The design of the tiles, developed on the basis of “scandole” technology, creates a visual impression of “movement” of the roof surface depending on the viewing angle and lighting.

In European countries, the traditional roofing material was tiles. Bituminous roofing materials have excellent performance properties.

The manufacturing company Tegola has designed several collections of soft tiles. The Nordland collection series is preferred for use in northern latitudes.

The serial line of the Tegola Antique collection has specific technical and aesthetic features. The shapes and lines create a tiled effect with rounded cell petals. The peculiar scaly configuration of the surface makes the roof unique and original.

Flexible tiles are created using Scandole technology. Even roofs with complex configurations look holistic and beautiful when using a soft roof. Visually, the impression of surface movement is created; the coating looks different under different angles and lighting.

Advantages

• Original configuration: shapes, lines, texture, colors.
• Efficiency in roofing systems of varying complexity.
• High resistance to external influences.
• Flexible tiles for use in northern climates.
• Long service life.

Bitumen has advantages over ceramic and metal counterparts. The materials from the Nordland collection are optimal for low-rise construction and private real estate. Roofs with flexible roofing look especially advantageous in suburban real estate and against the backdrop of natural landscapes.

Color palette

The Antik line of flexible tiles includes five shades of the color palette. Depending on preferences, customers can choose Tegola Antique Brown with shimmer or Antique Terracotta. Also in the serial line are textured colors Green, Red with shimmer, Blue with shimmer.

The Turnkey Roofing company offers Russian market. Materials flexible roofing The Antic line of the Nordland collection can be purchased with delivery in the regions of the Russian Federation. IN various cities Russian Federation There are suppliers of tiles to the manufacturer's dealer network.

Soft roof Tegola Antique

Price from 490 rub./m2

Bituminous shingles Tegola Antik is presented in the Tegola Nordland line. Designed for Russian climatic conditions: materials are adapted to frost, intense solar radiation, strong wind loads - this is a beautiful and durable roof.

The Tegola Antik soft roof collection includes 5 color solutions. Traditional, natural colors realistically imitate classic tiles. Bright, extravagant solutions attract attention and make appearance roofs are original.

Preparation for installation

After arranging the continuous flooring, the slopes are marked. When marking the roof, you need to make a series of lines along which its edges will be aligned when laying the covering. For marking you will need a construction cord and a pencil. On each slope, do the following.

Mark the line of the top edge of the first row of coverage (XY). It is carried out 19.5 cm from the edge of the cornice parallel to it.

To mark the center of the slope, place point A in the middle of XY, and at a distance of 1.5 m from it to the right and left - B and C. Measure a construction cord 2 m long and use it to draw circles from points B and C. In place the intersections of the resulting arcs mark point D. The line that passes through A and D to the ridge marks the center of the slope. A Z line is drawn parallel to it at 50 cm, along which the vertical edges of the coating sheets will later be aligned.

Up from the XY line, parallel to it, lines are drawn every 14.5 cm across the entire slope.

Laying the lining layer

Bituminous shingles are laid on top. They cover the slopes completely or partially. To protect roof structures from moisture, Westmet specialists recommend purchasing roll waterproofing. The technology for laying it depends on the angle of inclination of the slopes:

• with a large slope (from 30°), cover with waterproofing only those places where moisture accumulation is most likely. This is the perimeter of the openings skylights, valleys, ventilation and other exits to the roof. Roof overhangs must be waterproofed. Parallel to them roll material laid in no less than two rows;
• if the slope is less than 30°, waterproofing will be required over the entire area of ​​the slope. Lay the material, starting from the cornice, in strips parallel to it. At the joints in the longitudinal direction, overlap 10 cm, in the transverse direction - 20 cm.

Installation of bitumen shingles

Tegola soft roofing is installed from the eaves to the ridge. For the first row, trim the rounded petals on the covering sheet to create a straight line. The width of the resulting strip is 19.5 cm. It is laid along the cornice, aligned along the XY line. Laying begins from the center of the slope and proceeds in both directions.

Vertical edges next rows orient along lines AD and Z (in turn), starting with AD. The horizontal edges are aligned along the horizontal lines previously marked on the slope.

The sheets of Tegola Antique tiles have grooves and grooves along which they are aligned.

Use materials from packages with the same production code for the same slope to avoid color unevenness.

Cut the material with a convenient hook-shaped blade.

When installing shingles, you may not need to remove them at first. protective film from the wrong side.

Cover fastening

Shingles are attached in two ways, combining them:

• mechanically (with ribbed nails with a diameter of 3.2 mm). Use galvanized nails with oversized heads;
• gluing. Bitumen mastic is used, thin layer which (up to 1 mm) is applied with a spatula. The continuous flooring at the gluing site is covered with 2-3 cm strips of mastic with 2 cm gaps.

Additionally, if reliable fixation is required or installation is carried out in cold weather, inner side The shingles are heated with a hair dryer.

Mechanical fastening:

• to fasten 1 shingle you need 4 nails;
• nail holes are placed on adhesive strips;
• the nail leg must penetrate two layers of covering: the top and bottom shingles;
• When the slope slopes from 60°, use 2 additional nails to secure the edges.

Additional treatment with bitumen mastic and heating with a heat gun are needed where high-quality waterproofing is required: along the perimeter of dormer and attic windows, along the eaves line, in valleys, around passage elements.

Arrangement of the valley

The waterproofing is laid in a strip 1 m wide, aligning it along the axis of the valley. Every 10 cm, the rolled material is secured with nails at the edges. The coating is fused or glued on top waterproofing material. Laying is done using the “Undercut” method.

A flatter or shorter slope is closed first.

The shingles are bent over the valley axis and brought to the opposite side. The edge is aligned 30 cm from the valley axis parallel to it.

On a slope with a laid coating, a line parallel to it is drawn 10 cm from the valley axis. The shingles are placed on the second slope, inserted behind the axis and aligned along the intended straight line. If necessary, the edge is trimmed. When pruning, use hard backing material.

The shingles are glued with mastic, fused, and fixed with nails (but no closer than 30 cm from the axis of the valley).

Ribs and skates

The top row of shingles of Tegola flexible tiles on the slope is bent, placed on a ridge or edge and secured to the second slope.

Cut from roofing material ridge elements in the shape of trapezoids. Afterwards they are laid on the ridge with an overlap.

The laid elements are glued to mastic, fused and fixed with two nails. The nail holes are covered with the next ridge element.

Consult with Westmet specialists before buying a soft roof Tegola Antique when:

• According to the project, the house has an attic;
• the roof decking is not made of materials listed in the instructions;
• you plan to use bitumen shingles for a roof with slopes longer than 9 m;
• the house is located in a region with a difficult climate;
• you plan to carry out work at temperatures below +10°C.

Important: the lower (visible) and upper parts of the shingles may have different shades. This is not a defect or defect.

The Westmet company offers to buy Tegola Antik soft roofing, materials and components for its installation at competitive prices.

All colors and complete equipment of Tegola Antic from the Nordland collection, current prices. In this series of Tegola Antique soft tiles, the semicircular shape of the pattern is called “Beaver Tail”. Measurement, delivery and installation.

Bituminous shingles Tegola Antik- the design of this roof was developed using the “scandole” technology, which creates an imitation of a “moving” coating. The “Antique” scaly shape allows it to be used with particular efficiency in complex architectural projects.

This series will interest true connoisseurs of antiquity, those who are tired of faceless modern style, the bustle of the city, in which they forget about such a thing as art and prefer to plunge into times that were famous for their masterpieces and great conquests.

Colors of the Tegola Antique series

IN Tegola series Antic yes solid colors, for example, green, which is friendly with the color of nature itself and emphasizes its pristine nature. And colors such as red, brown, terracotta, blue with chaotic darkening from granulate create a mosaic carpet in a unique ancient spirit.

brown with shimmer

red with shimmer

shimmer blue

terracotta

green

Download price list:

The wave shape, alluring with its infinity, and the combination of several colors on one surface give the roof antique look.

Photo of Tegola Antic roof

We have selected excellent photographs from the Antique series for you. Considering ready-made houses with Tegola roofing, you can determine that color palette, which interests you. Mentally attach your facade to this roof and make right choice. You can also see the shape and color in offices where there is a choice facade materials, which can be used when choosing a roof.

Specifications

Tegola Antic has a thickness of 3 mm, which is based on a multilayer structure:

• Durable fiberglass impregnated with bitumen is the base.
• Modified bitumen compound SBS, oxygenated - filler.
• Basalt chips for protection bitumen roofing from external influences and imparting color.

Basic parameters of bitumen tiles.

Tegola Antique colors: Shimmer Green, Shimmer Red, Shimmer Brown, Terracotta, Shimmer Blue.

The cost of antique goods has always been quite expensive. In the case of Tegola roofing from the Antique series, you get an “antique” look for little money. Compare the cost of a high-quality, durable roof with similar products from the USA or Canada and you will see that it is affordable.