How to clean old rust in a toilet. What and how to clean rust in the toilet and cistern. Vinegar with soda

Shared

Cleanliness of the toilet is one of the first conditions of hygiene. But rust, which appears due to water oversaturated with iron, spoils the appearance of plumbing fixtures. The given methods and means of dealing with deposits in the toilet and cistern will allow you to keep the bathroom clean.

The cause of rusty deposits is old pipes. When building new houses, modern polypropylene (PP), metal-plastic or PVC are installed in apartments, but the plumbing system mostly consists of old metal (steel) or cast iron pipes. Water flowing through pipes carries with it sand and other suspended matter that settles on the walls of the plumbing.

Poorly adjusted valve cistern also causes rusty stains on the toilet.

The porous structure of the surface of plumbing fixtures is another reason for the appearance of rust. The surface of porcelain and earthenware toilets with a glossy finish is quite smooth, so they turn red much less often.

How to remove rust and yellow stains on a toilet

There are many methods for cleaning plumbing fixtures. Folk remedies will cope with fresh rust stains, but in the fight against old stains it is better to use chemicals.

Household chemicals

Based on their composition, household chemicals are divided into alkaline, acidic and abrasive.

Removing rust with acids

Before working with acids, put on protective gloves and a respirator, an old robe or a kitchen apron. Pour the solution carefully. Avoid inhaling fumes or splashing acid. After this, close the removable toilet lid.

Hydrochloric acid

Spread 20 grams of hydrochloric acid on the dirty stain.
Rinse off with water after 20–30 minutes.

Oxalic acid

Apply oxalic acid powder to a damp sponge and wipe the rust area.

Phosphoric acid (5–7%)

Pour some phosphoric acid into the tank and toilet.
Leave for 15–20 minutes.
Wipe with a brush and kitchen napkin.

Phosphoric acid will quickly clean the surface of rust

Used if sewer system not made from plastic pipes. Battery electrolyte is used only in the form of an aqueous mixture. Pour the acid into the water in a thin stream, and not vice versa.

To achieve cleanliness, just wipe the walls and pour about a glass of solution battery electrolyte in the toilet

Folk remedies for cleaning the toilet

You can remove rust without purchasing expensive household chemicals. To do this, you will have to remember traditional methods.

Brush and brush

It is important to thoroughly clean hard-to-reach areas under the toilet rim where rust and other deposits collect. Use a brush and an old toothbrush to wipe off dirt around the lid mount and under the rim.

It is important that the brush removes rust even in hard-to-reach places

Vinegar and baking soda

Heat a glass of vinegar (9%) to 40 0 C.
Add 2 teaspoons of soda to it.
Stir.
Apply the resulting solution to rust stains.

Do this in the evening so that the solution does not wash off overnight.

Acetic acid and baking soda will help remove a significant portion of plumbing contaminants

Ammonia and hydrogen peroxide

Mix 100 grams of peroxide and 5 grams of ammonia in a bowl.
Apply the solution to the rust.
After half an hour, wipe the contaminated area with a soft brush.

White

Apply Whiter to the surface for 30–40 minutes, clean the toilet with a brush and rinse with water.

Coca Cola

Wet a sponge with Coca-Cola and place it on the rust stain.
Pour the remaining drink into the toilet.
Leave for several hours, possibly overnight.
Wipe the dirty area with a sponge and clean it with a brush inner part.

Toothpaste

If you have a tube of cheap toothpaste left at home, you can simply squeeze it onto an old brush and rub the rusty area. WITH old stains she won't cope.

How to remove rust from a cistern

The already mentioned alkaline and acidic solutions will help to wash off rust in the cistern. chemical substances. Pour the product into water, leave for several hours (overnight is possible), and then rinse.

Possible mistakes when cleaning the toilet

Do not use soft sponges to clean the toilet, as they accumulate and multiply pathogenic bacteria, or throw them away after use.
Select for cleansing inner surface Toilet cleaners that will cause minimal harm. Use abrasives as little as possible - they destroy protective covering plumbers.
Substances intended for cleaning bathrooms (metal, cast iron, acrylic, etc.) are ineffective due to their composition.

Video: about the effectiveness of some folk remedies for cleaning the toilet

Preventing rust

To keep your bathroom clean, use preventative measures regularly. Adjust the tank valve so that the float does not leak water. Bend the float arm or replace the internal parts of the tank.

Buy special tablets for the tank (Bref, Kolorado, RIO, Domestos, Salix, Chirton and others). By interacting with the water in the tank, they will purify it and prevent the appearance of plaque and deposits.

Clean the walls of the toilet regularly with a brush to prevent old rust from accumulating.

Video: why the toilet is dirty and how to clean it

To keep your plumbing sparkling clean, regularly fix leaks in the tank and clean the toilet from dirt, sediment and rust. Choose cleaning products and detergents based on their safety and effectiveness.

Every self-respecting housewife keeps the bathroom clean, carefully removing rusty stains and limescale from the toilet. Often this painstaking task takes a lot of time, and therefore it’s time to find out how to clean a toilet from rust and plaque quickly and for a long time, saving time for more pleasant chores.

Causes of rust and lime

Agree, a dirty toilet disgusts each of us, but most often we ourselves are to blame for its neglect. The main reasons for the appearance of stains and smudges:

water quality;
old pipes;
malfunction and constant leakage of the tank;
high level roughness of the toilet;
lack of water-repellent coating;
a large number of calcium salt in water;
household uncleanliness.

Rust and limescale have various causes. Yes, excessively hard water with excess iron will certainly cause marks. This situation will worsen if the tank is leaking. And if excess iron leads to rust, then excess calcium salt in the water will certainly lead to limescale deposits accumulating at the rim of the toilet bowl.

However, the purchase of a toilet itself can already cause stains to appear quickly. A rough option without a water-repellent coating and improper cleaning of it quickly lead to scratches and the clogging of dirt, rust and lime. The reason lies in the uncleanliness of household members, which can gradually lead to serious and difficult to remove urinary stone stains.

You can avoid its occurrence if you introduce in your family the habit of flushing after each trip to the toilet or when your children empty the potty.

Methods of cleansing

It is important to wash and clean any dirt on the toilet as soon as possible. The fact is that it is very difficult to wipe off ingrained rust without damaging the finish of the bathroom. Cleansing at home can be done using a variety of methods, most of which are as accessible and effective as possible.

Household chemicals

It’s easy to get confused in the toilet cleaning products offered today, lost in the widest range. In reality, each of them belongs to one of four groups, created on the basis of differences in composition. Types of products to combat limescale and rust:

alkaline;
powder;
acid based;
based on chlorine.

It is recommended to give preference here to gel-like and balm-like textures.. They are able to provide not only high-quality, but also safe cleaning without damaging the toilet cover. Alkaline products include all sodium-based anti-plaque and rust stain products. They are considered absolutely by safe means, easy to use and highly effective. Among the well-known brands, the products “Dosya” and “Bref” stand out.

Powder formulations are among the most powerful in their action. So, they are practically the only ones who can cope with urinary stones. Using a stiff brush, the powder is rubbed into the surface, on the one hand removing difficult stains, and on the other, creating microcracks for future accumulation of dirt. That is why drugs such as "Pemolux" and "Flash" should only be used in extreme cases. Chlorine-based products are also suitable for DIY toilet stain removal. By applying it from the inside, you can notice how the plaque literally slides down, and the surface is disinfected.

Unfortunately, bleach and chlorine-containing products have a strong odor, leading some users to turn to advanced products. This category includes the products “Komet” and “Silit”.

Products based on oxalic, formic, hydrochloric and other acids are not inferior to bleach in cleaning. Products such as " Santry" or "Toilet Duckling" They do not have a strong odor, but with prolonged use they can negatively affect human health. Such products should be used periodically, remembering the prohibition of their use when washing earthenware and ceramic toilets.

Folk remedies

As you can see, the majority ready funds for cleaning have certain restrictions on use. Some housewives avoid such difficulties, consciously using only gentle folk remedies for cleaning:

Thus, one of the popular washing methods is a solution of iodine with vinegar. Small capacity filled with vinegar, a few drops of iodine and a pinch of soda. The solution is thoroughly mixed and applied to the surface to be cleaned for 6-8 hours, and then washed off clean water;
An interesting and popular method is pouring Coca-Cola into the toilet or flush cistern. Yes, exactly the drink that all children, without exception, love. After leaving the solution overnight, rinse the bathroom with water in the morning;
Citric acid and soda are used in cleansing according to the same principle. This or that product is poured onto the contaminated surface and left to act overnight. In the morning, wash off the product with water or rinse thoroughly if cleaning took place from inside the tank;
Hydrogen peroxide in tandem with ammonia can be a successful alternative to store-bought products. The proportion is 5 ml of ammonia per 100 ml of peroxide. The solution is carefully applied to the surface and left for about half an hour, after which it is cleaned with a medium-soft brush and rinsed off.

It is worth noting that traditional methods also contain acids. So, for cleaning in pure form Oxalic and hydrochloric acids can be used. As mentioned earlier, the method is not the safest, and therefore it is important to work with strong gloves and a respirator in advance. Inhaling such compounds is extremely harmful.

It must be said that ready-made and folk remedies are equally effective, however, those who want to get a quick result still turn to purchased products, because it is unlikely that any of them require settling at night.

How to prevent rust and plaque?

The appearance of rust can and should be prevented, especially since it is not at all difficult to do. So, first of all, apartment owners should adjust the toilet float and completely eliminate the constantly running thin stream of water. Even hard water with an adjusted bathroom will have a much lesser effect on the appearance of rust and limescale. It is worth noting that Replacing old rusty pipes will also help fill the drain tank with clean water without unnecessary impurities.

Unfortunately, not everyone dares to take such a labor-intensive step, but when done, the result pays off all the time and money spent.

If replacing pipes is still not part of your plans, softening tablets placed daily inside the tank will help improve the condition of the water. Additionally, such products envelop the bathroom with pleasant aromas, which plays an important role. A more thorough method is to install a water filter in a drain structure. It is not cheap, but water purification when using it ceases to be a daily procedure with the participation of a housewife.

Sometimes even if all recommendations are followed and preventive measures the bathroom continues to quickly accumulate rust and plaque. Most likely, the problem here lies in improper cleaning some time in the past, because a hard brush can seriously damage the coating in just a few uses. If scratches are visible to the naked eye, the best solution will be the replacement of plumbing and careful adherence to the rules for cleaning it. Untouched by potent drugs high-quality coating a toilet bowl can last for decades, pleasing its cleanliness and aesthetics.

For more information on how to quickly and effectively clean a toilet, watch the following video.

Perfect cleanliness in the bathroom is possible, but it requires a lot of effort. Most housewives are sure of this. However, if you know the nature of the contaminants that appear inside plumbing fixtures and use well-chosen means to combat them, the task becomes much easier.

Let's talk about how to clean a toilet quickly, efficiently and without much expense.

A sparkling clean toilet is a source of pride for any housewife. But, unfortunately, he doesn’t remain that way for long. A short time after cleaning, unpleasant red stains may appear on the surface of the equipment.

These are streaks of rust, iron oxidation product or other metal alloys. It seems that there is nowhere for it to come from in the toilet, which is made of ceramic with plastic parts.

However, there are several reasons for the appearance of rust. The first is the deplorable state of engineering communications. Old lines were made of non-galvanized metal, which inevitably corrodes over time.

Oxide particles fall into the water, which leaves a rusty mark on the surface of the equipment.

Rust stains are very difficult to remove from a toilet bowl without the use of special cleaning products found in household or store bought

Frequent causes of rust stains also include iron-enriched water entering the water supply and leakage of liquid from the tank.

In addition to rust, it leaves marks on the surface of the toilet. The intensity of its formation depends on the composition of the water used in the water supply system.

It necessarily contains various mineral compounds that settle on the walls of the toilet and form an unpleasant, hard grayish coating. The more lime compounds in the water, the faster plaque appears.

And the third “enemy” of cleanliness of plumbing equipment is urinary stone. It is formed similarly to limescale, the only difference being its composition. The stone is formed from minerals contained in human urine.

When the toilet is used carelessly or when flushed irregularly, urine residues linger on the surface of the toilet, forming a hard coating of an unpleasant brownish-yellow color.

Ideally, for each type of toilet contamination, you should use special remedy, it’s easier to deal with them that way. But universal solutions can also be useful

Thus, there are three main types of toilet contamination. They differ significantly from each other in their chemical composition, accordingly, you can get rid of them using different means. Although there are universal methods cleansing that will help in all cases.

I would like to note one more point. All types of contaminants first begin to be deposited where the surface of the toilet bowl has become rough or microcracks have appeared.

Most often, ceramics lose their smoothness after contact with overly hot liquids or objects. Extremely not useful for the toilet and sharp changes temperatures, since microcracks may appear as a result.

You need to know that budget models of plumbing fixtures are made from ordinary sanitary ware with fairly high porosity. This material is prone to the accumulation of contaminants. It is better to purchase equipment made from sanitary porcelain, which has an increased surface smoothness.

Where to start cleaning?

Whatever method of cleaning the toilet you choose, you should not forget about the preparation stage. First of all, you should take care of protection. All work should be carried out only with rubber gloves.

They will protect the skin on your hands from aggressive cleansers, and you shouldn’t forget about basic hygiene. The toilet is a place where pathogens accumulate.

When working with aggressive chemicals, the use of rubber protective gloves is mandatory. Otherwise, you can develop allergies or dry out your hand skin.

For the same reason, it is advisable to wear an oilcloth or plastic apron. It is good that it covers as much surface as possible. This will prevent germs from getting on your clothes. If aggressive chemicals are to be used, a respirator should not be neglected. Airways must also be protected.

And a few more words about safety. Try to ensure that cleaning solutions do not come into contact with the skin, much less mucous membranes. If drops of the product do get on them, you should immediately wash them off with water.

When working with products with a strong odor, always leave the doors in toilet room open. The same should be done in the case when gas is formed during the interaction of cleaning agents.

It is advisable to start cleaning the toilet by removing the water. It needs to be scooped out of the device and poured out. For this it is very convenient to use a ladle with a long handle. Only after this can you begin to apply cleaning products.

We fight pollution with folk remedies

Not all housewives are ready to use aggressive chemicals in the fight for cleanliness and prefer to make do with milder “folk” remedies. There is nothing wrong with this, especially since these methods are quite effective.

Especially in the early stages, when plaque and stone have not had time to harden too much. Let's look at how you can clean a toilet using popular gentle methods.

Method number 1 - soda with vinegar

It seems that everyone knows how to clean a toilet with soda and vinegar, but there are some nuances here. First, prepare the baking soda; one package will be enough. After this, we moisten the inner surface of the equipment, so we will prepare it for processing.

Fill the toilet with baking soda. It will stick to a wet surface. If there are areas with plaque and stone, be sure to literally coat them with wet soda.

Regular baking soda is a powerful cleaning agent, but it just needs to be used correctly. It is effective both when used separately and when paired with vinegar.

Leave the toilet like this for about half an hour. During this time, the soda will react with the contaminants and begin to destroy them. After the time has passed, take a container with table vinegar. If only essence is available, it is better to dilute it. Carefully pour the vinegar onto the soda-sprinkled surface of the toilet bowl. A violent reaction will begin, which will help remove contaminants.

We take a brush and scrub away the dirt, “helping” the seething chemical reaction. After it’s finished, go over the bowl with a brush again and rinse the toilet thoroughly. It will take several flushes, or if you don’t want to wait for the tank to fill up, you can rinse the equipment with clean water from a bucket.

Method No. 2 – mustard powder

First, prepare the cleaning mixture. To do this, take two tablespoons of mustard powder, add an equal amount of crystalline citric acid and four tablespoons of starch.

Mix thoroughly until a homogeneous mixture is obtained. We begin to gradually add clean water. Stir until you get a paste. This will be our cleaning product.

A homemade product based on mustard powder will not only clean, but also disinfect the toilet well. The components included in the mixture are absolutely harmless to plumbing.

We moisten the surface of the toilet so that the mixture sticks better. Carefully distribute the mixture over the bowl. Thoroughly rub the product into particularly contaminated areas and leave it like that for about half an hour. Then rinse with water and at the same time with a brush. Wash off any remaining product with clean water.

Method number 3 - vinegar and salt

This method is especially effective for getting rid of urinary stones. We need one glass of table nine percent vinegar. If it is not there, you can dilute acetic acid according to the instructions, which are usually present on the bottle.

Pour the vinegar into a container that is not afraid of heat, and begin to heat the solution. It is important to remember that at this moment a pungent odor may appear, so it is advisable to close the container tightly.

From the simplest ingredients found in any home, you can create a powerful cleaning product. But it is important to maintain proportions in order to increase the effectiveness of the action.

Heat the vinegar to a temperature of about 40C, then add half a teaspoon of salt and mix well. Using the resulting solution, carefully treat the surface of the toilet. In areas with particularly heavy contamination, increase the amount of product by rubbing it into the stone.

We close the toilet with a lid and leave it in this state overnight. In the morning, remove the solution along with the contaminants by draining the water from the tank.

Method number 4 - wood ash

To prepare the cleaning composition we need an equal amount wood ash and crystalline citric acid. Usually, two standard packs of lemon juice and the same amount of ash are enough. Mix everything well.

We moisten the toilet bowl and fill it with the resulting product. Leave it like this overnight. In the morning, clean the toilet with a brush and rinse it, washing off any remaining product.

Acid solutions of different concentrations

As is known, acidic environment dissolves lime deposits and urinary stone very well. It is also effective against rust, so acids and products based on them are considered good choice for cleaning the toilet.

In practice you can use various acids without mixing with other substances. Using phosphoric acid is the best answer to the question of how to clean rust from your toilet.

The substance can easily be bought in a store, where it is sold in the form of an 85% solution. The product is a colorless, syrupy, very aggressive substance. You can only work with it using protection.

Prepare the cleaning product: take half a liter clean water and dissolve 100 ml of orthophosphoric acid in it, stir until a homogeneous mixture is obtained.

Acids can clean almost any contaminant, but you need to remember that they can ruin the plastic parts of the toilet and pipeline

Degrease the toilet bowl by washing it with any soap detergent. After this, apply the prepared cleaning agent, treat the surface with a brush, preferably with natural bristles. Leave the bowl with the solution for a while. Depending on the intensity of contamination, it may take from 1 to 12 hours.

After a while, rinse the toilet with a weak soda solution. To prepare it, dissolve a tablespoon of soda in each liter of water.

To remove rust and plaque, use and hydrochloric acid. But you need to know that it cannot be used for equipment with plastic and rubber parts, and its use is also excluded if the toilet is connected to a plastic pipeline. The acid will dissolve the plastic.

Approximately half a glass of hydrochloric acid is poured into the bowl, where it is left for 15 minutes. Then the surface is washed with clean water.

You can use lemon and acetic acid. Since their effect is somewhat weaker, this technique gives the best results. Toilet paper soak in vinegar and place under the rim and on contaminated areas.

Do the same with citric acid, but since it is crystalline, it may be more convenient to apply it to a damp cloth. Leave the product on for several hours, preferably overnight. In the morning, rinse with clean water.

Oxalic acid is used similarly to citric acid. This inexpensive product can be purchased at hardware stores.

Oxalic acid is also widely used for cleaning plumbing fixtures. The powder is applied to a damp cloth and applied to contaminated areas.

You can often hear advice on using battery electrolyte as a cleaning agent. This is really effective, but you just need to remember that the liquid contains acids, so don’t forget about caution and protection. Treat the bowl with electrolyte, leave it for 20 minutes, then wash it off with water.

Compositions of this type necessarily contain abrasives. These are very small, but sharp and hard particles, with the help of which mechanical restoration surfaces. Abrasives literally peel away dirt, thereby removing it from the surface. them in different quantities added to cleaning products.

In any case, it is not advisable to use such mixtures on ceramics. This is especially true for sanitary porcelain. Abrasives are left on smooth surface marks that look like scratches. Over time, more and more of them accumulate, the bowl becomes rough, literally “attracting” dirt.

Powders with abrasives cost very little, so they are very popular. However, you need to remember that solid particles spoil the surface of plumbing fixtures

If you still want to use cleaning products of this type, you should read the instructions on the can. Most often, in addition to abrasives, they contain some kind of bleach. Therefore, most manufacturers advise using their products in this way.

The powder is applied to a sponge moistened with water or directly to the bowl, after which it is intensively rubbed into the surface. Then you should leave the product for a while so that it “works” effectively. Then rub thoroughly with a sponge again and rinse with water.

Industrial cleaning products

This is a big group various compositions made on the basis of acids or alkalis. The former are more effective, since the acid does a better job of removing rusty swelling and limescale.

And here alkaline agents“work” well against organic matter, and therefore perfectly decompose urinary stones and fats. Let's look at the most popular formulations.

Gel-like “Cillit Bang” for toilets

All products produced under this brand have a gel consistency. They are packaged in bottles with a convenient spout-shaped dispenser, which helps deliver the solution to the most difficult to reach places.

Basics active substance The product contains hydrochloric acid. Therefore, it is best used against rust stains and limescale. At the same time, do not forget about protective equipment.

Cleaners industrial production very effective. You need to know that you cannot mix them. Unpredictable chemical reaction which is very dangerous

In the line of products you can find compositions of directed action: against rust, for disinfection, for whitening or shine, against difficult to remove limescale deposits. Consumers appreciate high efficiency composition, economical consumption and convenient packaging.

Of the shortcomings, the most significant is considered to be relatively high cost drug. But the gel is very easy to use. It should be applied to the bowl, left for 15-20 minutes, and then rinsed off.

“Domestos” for the toilet

This brand produces a popular multifunctional product for cleaning toilets and other plumbing fixtures. The product contains alkali, which copes well with the destruction of organic matter. For this reason, the product does not fight limescale very effectively.

In addition, the product contains chlorine bleach, so it not only whitens rust stains, but also disinfects surfaces.

Several varieties of the drug are produced, differing mainly in fragrances. The latter are necessary to drown out the extremely bad smell chlorine Consumers highly value the product for its high efficiency, thick consistency and economical consumption. One of the disadvantages is the sharp unpleasant odor of the drug.

Domestos is universal; in diluted form it can be used as a bleach and as disinfectant for kitchen work surfaces. And in undiluted form, it and other equally effective products can be used in sewer pipes.

Cleaning product “Toilet duck”

A liquid preparation produced in bottles of a characteristic shape with a strongly curved neck, which allows you to apply the gel in the most difficult to reach places. Duck contains hydrochloric acid, so it copes well with lime deposits and rust stains.

Somewhat worse, but still effective, the drug dissolves urinary stones. The acid concentration is quite high, so the product is aggressive towards bacteria.

The toilet duck is very effective remedy acid based. In addition to universal ones, the manufacturer produces highly targeted drugs to solve various problems.

The drug has a pronounced disinfectant effect. When working with the composition, it is mandatory to use protective equipment. Buyers noted good efficiency drug, convenient packaging, budget cost.

Duckling contains chlorine derivatives, despite this it has a pleasant smell. The disadvantages include a liquid consistency, which provokes rapid consumption of the drug.

Cleaning tablets and cubes

Many housewives, thinking about how to clean their toilet from urinary stone, do not take into account the numerous tablet cleaning products. They are produced by most manufacturers of household chemicals. This is an effective multifunctional product that can not only clean equipment, but also disinfect it and deodorize the air in the bathroom.

Cleaning tablets for the tank are a practical multifunctional product that copes with three main problems of plumbing equipment at once. The composition of such tablets and the concentration of active substances in them varies depending on the manufacturer.

Well-known brands produce products that are effective for one to two months. The water-soluble coated tablet is dropped into the drain tank. Slowly dissolving, it gradually “releases” the active substances into the water. As a result, the parts of the drain tank are cleaned. After pressing the flush button, the liquid enters the bowl, and it is also cleansed of all types of contaminants.

At the same time, the active substances easily reach the most inaccessible areas and clean them. Products can have a variety of scents; the user chooses any scent they like.

The tablets are quite effective, especially if there are no old contaminants. Among the disadvantages of the product, it is worth noting the rather rapid consumption of the drug, especially if a large number of people use the toilet.

Cleaning the toilet is not the most enjoyable task. However, this must be done regularly so that you do not have to use aggressive chemicals later to put the equipment in order.

If, nevertheless, the plumbing has an unsightly appearance, you need to determine the nature of the contaminants and select the most effective cleaning agent specifically for them, since their range is very, very wide.

Others known effective ways cleaning the toilet from dirt and do you successfully apply them in practice? Please tell other visitors to our site about them in the comments section. Or have questions about the topic of the article? Ask them, we’ll figure it out together.

Cleaning a toilet from rust

How to remove rust from a toilet? The question is always relevant, because the toilet and the bathroom always characterize the cleanliness of the housewife, moreover, these 2 household attributes can be carriers of many infections due to their intended purpose.

When looking at a sloppy toilet with urinary stone growths, rust and a leaking tank, any person experiences a feeling of deep disgust. It seems that the whole room is dirty, whether a person is squeamish or not, but such a toilet temporarily turns anyone into a neurotic, fixated on germs and dirt. Next we will talk about ways to remove rust and the most common reasons its formation inside the toilet.

Rust formation on the toilet

Today on the market you can find many household chemicals that promise to easily get rid of rust stains. Based on their consistency, consumers are offered: dry abrasives, liquid sprays and thicker, gel-like liquids.

Comet toilet cleaner

So, how to remove rust from a toilet? Abrasive products are often criticized because they leave scratches on the surface being cleaned, and this is true. If your toilet is new, then you probably won't want to ruin it right away. There is another disadvantage of these products - they are less effective than their alternatives in the form of gels and sprays.

Spray for cleaning toilets from rust

It would be possible to recommend a Comet containing chlorine for the toilet, but only if the dirt is fresh, but old and multiple dirt will need to be scrubbed off with force during cleaning, then, leaving the powder, make sure that it does not have time to dry too quickly, otherwise it will the cleaning function will stop. These actions are only suitable if your toilet has nothing left to lose - its surface is already scratched or cracked.

Gel Bref for cleaning the toilet from rust and plaque

Sprays. Sprays are effective, but more metal surfaces, tiles, but not for a bath or toilet, especially if we are talking about heavily soiled household items.

Gel-like cleaning liquids. The gel is thicker, more densely and evenly distributed over the surface, does not dry out as quickly as the first two categories of products and corrodes dirt better.

When buying any gel, choose one that contains acid. Chlorine-containing products are intended more for disinfection than as stain removers; they can clean some things, but the more complex the situation, the more useless they are. Lye works great in the kitchen, but toilets and bathtubs are not its strong point.

Toilet acid

The following acids are most often used for rust stains: acetic, citric, oxalic and hydrochloric. There is one folk recipe cleaning: pour hydrochloric or oxalic acid, or a mixture of both, onto the stain and leave for 25-30 minutes. Rinse the toilet with plenty of water.

Hydrochloric acid for cleaning toilets from rust

Hydrochloric acid. Of all the above acids, it is best to choose hydrochloric acid. Hydrochloric acid will definitely clean your toilet, no matter what contaminants it encounters, be it rust, urinary stone or lime, fresh or old multi-layered dirt build-up. It doesn’t matter whether your toilet is new and smooth, or cracked and old, hydrochloric acid will do its job, but if you choose it, it’s better to buy a ready-made cleaning product containing hydrochloric acid. The concentration of the above acid in these products is the safest for home use, while its cleaning properties remain brilliant.

Toilet cleaning gloves

When cleaning with this product, you need to wear gloves, as the manufacturer himself warns about, but even if by some accident a drop of such a cleaning gel gets on your skin, it will not cause serious damage to you, but if such a problem happens with a concentrated solution of saline acids - the damage to you could be irreparable, and accidents always happen.

You cannot store or use a solution of concentrated hydrochloric acid at home.

Cilit Bang, a special gel for toilet bowls, contains hydrochloric acid.

Cillit Bang toilet cleaner

The liquid has a beautiful green color, a gel-like consistency (not a spray) and is used only for toilet bowls. There are other products from Cilit Bang used for bathtubs, tiles and other surfaces, but they are much weaker, although the instructions for them say that the liquids can be used against rust.

Choosing toilet rust removers

Perhaps, in addition to Cilit Bang, you will find other brands of cleaning products from other manufacturers that contain hydrochloric acid - read the composition of the product on the bottle. As a rule, if the cleaning liquid contains this acid, then this product will not be universal in nature, but purely special, for example, only for the toilet.

Use a strong, acidic cleaner to clean the inside of the toilet, and use glass cleaner to clean the outside. With its help, you can easily remove dust and other surface contaminants, leaving the toilet sparkling clean.

Traditional methods of fighting rust

How to clean a toilet from rust using folk remedies? There are always folk remedies for all occasions, although they are not always effective enough, but for amateurs folk wisdom Several recipes are given.

Vinegar for removing rust

How to clean a toilet from rust with vinegar? Take a rag, soak it in vinegar and cover the stain to be removed, leave the rag there, eating away the rust, for a while.

There is another way to clean rust from a toilet: heat 70% vinegar to a temperature of 40 °C, then pour it into the toilet. This method is good for cleaning the toilet from limescale and stone.

A solution of vinegar and soda to remove rust on the toilet

The procedure is carried out in the evening so that the contaminants are exposed to acid all night. It is recommended to add 1 tbsp to vinegar. l. soda to increase its cleansing power. Iodine is added to 9% vinegar.

Citric acid is an excellent tool in the fight against rust.

You can use vinegar instead citric acid. Pour 2 bags of acid into the toilet and do not flush for 2 hours.

Ammonia and hydrogen peroxide are common stain removers. traditional methods. To clean the toilet from rust and plaque, ammonia mixed with hydrogen peroxide in a proportion of 100 ml of peroxide to 5 ml of ammonia. Pour the resulting solution onto the stains and leave for half an hour.

Hydrogen peroxide is used to remove rust

Another effective, but very controversial way to clean the toilet from rust, urinary stone and plaque is to use electrolyte for car batteries.

The hygiene in the house and the cleanliness of the residents can be judged by the condition of the plumbing. Dirty toilet with yellow stains does not add to the image of the owners, but you can clean the toilet from rust household chemicals or improvised compounds. You just have to want to remove the dirt.

We use household chemicals

The most effective and easiest way to clean rust in a toilet is with the use of professional store formulations. Let's take a closer look at them.

Abrasive agent "Pemolux" and its analogues ( “Komet”, “Sarma”, “Sorti”, “Sanita”). The powder is applied to the pre-moistened stain with a napkin and the composition is left to interact with the surface for up to half an hour. Then clean it by rubbing with a hard sponge or brush, and wash off the powder with water.

The use of abrasives is effective, but there is one caveat. When they are used, microcracks appear on the surface. Each time the destruction intensifies, the pollution penetrates deeper and becomes more and more difficult to cleanse. It turns out that the more often you wash the toilet with Pemolux or the like, the dirtier it becomes.

Advice
When choosing a toilet, give preference to porcelain sanitary ware, which, unlike earthenware, is less porous and less susceptible to contamination.

Alkaline compounds like “Domestos”, “Dosya”, gel “Sarma”. They eat away dirt without harming the surface. Apply the product by applying it to the area with rust and leaving it for 15–20 minutes. Then washed with water. The method is simple and not labor-intensive, but it may not be susceptible to severe contamination.

Advice
Alkaline chlorine compounds are used to clean plumbing fixtures and bleach to a dazzling shade.

Special anti-rust products containing acid, primarily oxalic. Among these, they stand out for their efficiency “Silit”, “Sanita”, “Toilet duckling”. The principle of cleaning with them is based on the dissolution of contaminants, as with the use of alkaline compounds. Therefore, the method of using them is the same - the liquid is applied to the dirt, left for 10-20 minutes and washed off with water.

Advice
The acid is caustic and should not be used to clean enamel-coated plumbing fixtures. But for earthenware and porcelain, compositions with acid are just the thing.

Cleansing with folk remedies

At home, you can use improvised acid and alkaline substances: soda, vinegar, citric acid or juice.

Soda with vinegar

The inside of the toilet is cleaned white using several home methods using vinegar and soda. With their help, you can remove not only rusty stains from the toilet, but also yellowish urinary stone.

Method 1:

1 cup vinegar essence or table vinegar heated to 45° C.
Mix with 1 tbsp. l. soda
If the product is prepared from 9% vinegar, then you need to add a few drops of iodine to the prepared mixture.
The resulting composition is applied to the problem area of the plumbing. If you need to clean the toilet under the rim, use a container with a narrow hole.
Leave for up to 12 hours.
Wash off with water.
If you are unhappy with the result, repeat the procedure the required number of times.

Method 2:

Half a glass of soda is poured into the toilet.
Then it is carefully poured with vinegar.
The sizzling mass is distributed with a brush over the entire inner surface of the toilet.
Wait half an hour, thoroughly clean the dirt with a brush.
Wash with water.

Baking soda

It is a soft abrasive and has a safe action. A slurry is prepared from soda and water, which is applied to the area with rusty stains. After drying, the product is washed off with water.

Table vinegar

To wash plumbing fixtures, use it to generously soak a cloth and wet the rusty marks well. Leave for half an hour or an hour, then rinse with water.

This is an effective way to clean a stepped toilet (“with an oblique outlet”). Water is first removed from the top of the bowl, and during soaking, the drained vinegar is periodically lifted and distributed again over the walls.

Ammonia and hydrogen peroxide

They are used in a similar way to vinegar:

Mix peroxide and ammonia in a ratio of 1:5.
The product is applied to the contamination.
After waiting half an hour, rub with a brush and rinse with water.

Ammonia has a pungent odor, so be sure to turn on the hood or ventilation amplifier, and cover your nose and mouth with a medical mask, or better yet, a respirator.

Lemon acid

Its crystals act more effectively than vinegar, and the product does not drain from the walls as quickly. There are two ways to clean with lemon.

Method 1:

Pour citric acid powder onto a napkin.
Wipe the pre-moistened rust stain.
Leave for up to an hour and a half;
Wash with water.

Method 2 – if you need to remove rusty plaque and yellow stone:

Several packets of acid are poured into the toilet.
Leave for 10-12 hours. Urine stone softens and can be cleaned.
Rub with a brush and rinse with water.

Oxalic acid powder

Many housewives call this substance the ultimate rust remover.

The powder is used as follows:

Apply to a surface moistened with water using rubbing movements.
Leave for half an hour.
Wash with water.

Advice
It is necessary to work with alkaline and acidic compounds while observing safety precautions. And be sure to wear rubber gloves.

"Whiteness" and other chlorine-containing bleaches

Method 1:

The liquid composition is poured onto the contaminated surface.
Leave it overnight and then wash it off.

Method 2 – radical, but fast:

Use an alkaline powder (for example, “Sanitary”) to wipe the inside of the toilet, focusing Special attention rusty stains.
Leave for 5-10 minutes.
Pour “White” into the toilet and wipe all surfaces and the drain, distributing the bleach over the powder.
Rinse well with water.

Important
In the second method, alkali and acid neutralize each other, and chlorine is actively released into the air. Therefore, this method can only be used with the hood turned on and wearing protective equipment. Children and animals should move away.

Carbonated drinks

"Pepsi", "Coca-Cola", "Sprite", others dissolve limescale and remove fresh stains of rust.

Cleaning methods:

The drink is poured into the toilet. If you need to clean the plumbing under the rim, soak a napkin in soda and apply it to the dirty area.
Leave for an hour.
Wash with water.

Advice
Water leaking from the tank significantly reduces the efficiency of purification and it also - main reason rusty path in the place of flushing.

Toothpaste

It is advisable to take a bleaching one without colored inclusions. Toothpaste- a product with a mild abrasive effect and helps to get rid of only fresh dirt. Her

Mode of application:

The paste is rubbed into a damp, dirty surface.
Leave for half an hour.
Wash off with water.

Prevention

The cause of rust stains and yellow coating is water. It always contains iron, and if there is leakage from the flush, rust quickly grows on the wall and around the sump in the toilet bowl. If there is a lot of rust in the water, then it remains on the walls even if the tank is in full working order. In the first case, it is enough to adjust or replace the flushing mechanism; soluble tablets for the tank or fresheners with a cleansing effect, which are attached under the rim, partly help.

In case of extreme hard water more radical measures will be required. The source of water pollution is non-galvanized metal water pipes, corroding from long-term use. Accordingly, ideally the pipes are replaced. As a compromise, a filter is installed on the water supply entering the house and checked monthly and, if necessary, washed or replaced. Both procedures are quite expensive.

A rusty coating on the tank and the surface of the toilet spoils appearance bathroom and reduces the service life of plumbing fixtures. Helps prevent stubborn stains regular care: weekly washing with products against rust and lime deposits, timely repair of the tank and replacement of pipes with metal-plastic ones with a cleanable filter.