DIY Christmas trees made from plastic bottles. New Year's craft: DIY Christmas tree made from plastic bottles. Creative DIY Christmas tree

Today we bring to your attention the process of making a large holiday tree from simple plastic bottles Green colour. This Christmas tree is collapsible, so it can have any number of tiers (you only need a longer “stem”). You can add more layers each year and within a few years you will get a big fluffy beauty around which your children will dance in circles.

To make a Christmas tree from plastic bottles you need:

Green plastic bottles (it took 1.3 liter bottles about 30 pieces);

Steel part (“rod”) of the desired length (here about 0.5 m, with an approximate diameter of 0.5 cm);

Single-core aluminum wire insulated (section 2.5mm2);

Christmas tree stands;

Scissors, heat gun;

Christmas tree made from plastic bottles step by step:

Take the bottle and cut off the middle part from it, as in photo 2-3. Then cut this part of the bottle in a spiral using scissors, cut a strip with an approximate width of about 2 centimeters (photo 4).

Next, you need to bend one edge approximately 0.5 cm along the entire length of the strip, as in photo 5-6. This side will help set the direction for spruce needles (needles), and will also serve as a limiter for cutting the “needles”. Cut a fringe strip about 0.1 cm wide (photo 7-8).

Then start creating spruce branches. Let's make a “top” for the Christmas tree, for which wrap a strip of plastic (about 8 cm long) around the “rod” and glue it using a hot-melt gun (apply glue to the “rod”, otherwise the workpiece will high temperature may become deformed) (photo 9). Next, twist a small piece of fringe and glue the pieces inside (photo 10). Then wrap the “rod” in a spiral with a strip of fringe (photo 11). When one strip ends, take another and continue gluing (photo 12-13).

After making the top, make the first tier of branches, which will consist of three short parts (a branch with an approximate length of about 7-8 cm). Make a wire frame, as shown in photo 14, connect it to a plastic ring (photo 15-16).

Start wrapping the “branches” in the same way as the top (photo 17). After creating all the branches, braid the “needles” and the main stem (photo 18-19). As a result, you should get two parts, as in photo 20.

Make the third detail of the future Christmas tree, a remote one. At first it was made too high, so it was moved to the bottom of the tree and the piece was made smaller. In total, four distances were used for this tree: Upper - approximately 0.5 cm; the second - about 0.6 cm; third - 7 cm; the lower one is 8 cm. Make “distances” by analogy with making the crown, just do not close the upper hole (photo 21). The Christmas tree will look at this stage as in photo 22.

Next, make a second tier of branches, which will be wider than the first and will already include four branches (with an approximate length of about 9 cm), each of which will have two side branches. The length of the main branches turned out to be approximately 9 cm (photo 23 -24).

Wrap the frame, starting with the smallest branches, then the main ones, and ending with the trunk (photo 25-26). Under the influence of hot glue, the plastic heats up and takes on a fairly plastic shape, making it very easy to set the direction of the needles for each branch at the junction of the branches (photos 27-29).

The central part of the stem before camouflage with pine needles looks like in photo 30, and after camouflage it looks like in photo 31. Next you need to make a second spacer part (photo 32).

Next comes the production of the third tier, with an approximate length of branches of about 10 cm (20 cm in diameter) (photo 33). Finally, make the lower tier (branches 15 cm long (30 cm in diameter)) and the lower distance (photo 34).

All that remains is to install everything on the stand! If desired, you can make any number of tiers, and each subsequent tier should be proportionally wider than the previous one - this way you can get a tall and elegant Christmas tree.

The Christmas tree made from plastic bottles is ready!

According to the site: girlsschool.ru

At the bottom there should be the largest bottles (2 and 1.5 liters, in the middle - liter bottles, and at the top 0.5 and 0.3 liter bottles. If you have bottles of the same volume, then adjust the length of the “branches” yourself by cutting stripes up required length.

Make a hole in the left bottom, which you secure to the lower end of the stick using a plastic bottle cap (you can hammer a nail in for strength).

Place the last, smallest piece, neck up, on the upper end of the stick and screw the green plug onto the neck, also securing it with a nail for strength.

A little patience, perseverance, effort and the forest beauty is ready!

Such Christmas trees can be used as New Year's decoration your houses!

Method 2. To make such a Christmas tree you need a minimum of time and expense. A master class on making a Christmas tree from plastic bottles will tell you in detail how to make such an original New Year's craft.

To make a decorative New Year's craft: a Christmas tree from plastic bottles, you will need the following:

Plastic bottles - 3 pcs;
Scotch;
Sheet thick paper, ideally whatman paper (A4);
Scissors;

	So, cut the bottle as shown in the photo. That is, it is necessary to cut off the bottom and neck so that a straight pipe from the bottle remains.
	Next you need to make blanks for the branches. In order for the tree to have a cone-shaped shape, the blanks must have different sizes. That is, you need to achieve the following:
	Cut each plastic bottle lengthwise into 3 equal parts and then adjust their sizes so that each subsequent tier is slightly smaller than the previous one. Then each workpiece must be “dissolved into needles.” The neck of one of the bottles will serve as a stand for our future New Year's craft.
	The next step is to roll the Whatman paper into a tube. We insert it into the bottleneck...
	...and secure with tape.
	Now all that remains is to fix each tier of the tree with tape in a circle and a little New Year's craft: the Christmas tree with your own hands is ready!
	The top of our New Year's tree you can decorate with homemade Christmas tree toy or complete the Christmas tree the way we did it.
	If you want to make a Christmas tree from plastic bottles more fluffy, like in the photo, when making the Christmas tree, you need to cut the needles as thinly as possible (more often).
	By the way, the Christmas tree also looks quite creative with larger “branches” - a maser class from the website Country of Masters. We cut the bottle in the same way as in the previous version into 3 parts. Only we make cuts in a circle towards the center, straight.
	A puncture is made in the center with an awl and the needles are bent up and down in order. A puncture is made in the lid of the cream or mineral water into which a skewer of the required length is inserted.
	The parts are strung in descending order, with a large bead placed on top of the glue. The Christmas tree can be decorated with polystyrene foam, rain, etc.
	Glue the Christmas tree onto the disk stand. The Christmas tree is ready!
	You can put gifts or plant an animal nearby. These Christmas trees have been a constant success for many years.

Method 3. And finally last option for today - a Christmas tree made from plastic milk bottles (what decorative New Year trees are not made from...). The design is completely collapsible, has maximum resemblance to the original, does not require special complex technologies and specific work skills, there are no problems with bottles either, and a holiday is just around the corner...

Materials and tools

The material for making the Christmas tree is a milk plastic bottle or part of it (Fig. 1). To make a homemade tabletop Christmas tree, you will need 5-20 milk/kefir plastic bottles with corrugation at the bottom. The number of bottles determines the number of branches and tiers. The more branches, the more fluffy the Christmas tree is; the more tiers, the taller it is.

In addition to bottles, you only need scissors and plastic rivet technology

Plastic rivets

To implement the technology of plastic rivets, it is necessary to have a means for melting (installing) the rivets and the rivet itself. You need to manage to melt the head of the rivet using a hot nail or lighter. You can do this in the same way with a well-heated soldering iron. In addition, you will need clamps and tweezers to install rivets in hard-to-reach places.

For plastic rivets, it is very important to choose the material. After fumbling for about a year, through trial and error, taking into account the requirements of strength and availability, I identified several sources for obtaining plastic rivets:

1. Empty ballpoint pen refills. Enough available material. They are good because they are colorless and the compound, with their help, turns out to be organically integrated into the product made from plastic bottles. Such a rivet turns out neat, with a round head, however, it has a slightly reduced tensile strength. In addition, the rod from ballpoint pens is round in cross-section and completely fills the drilled hole in the parts being connected. By the way, the walls of the rods are different thicknesses, for rivets it is better to use rods with thicker walls.

2. Chupa Chups sticks. Similar to option No. 1 only in color. The connection is more cumbersome, and the rivet head melts with difficulty (it either burns, becomes ugly, or unreliable).

3. The most perfect option, and very convenient (I give the world a suggestion) to use material from buckets with construction mixtures for 3, 5, 10 liters There are quite a lot of them left after repairs, and even one lasts for a long time.

From the walls of such a bucket you need to cut a ring, and cut the ring along the generatrix (this is the only way) into strips 2...4 mm wide, length from 4 to 15 cm. These will be the blanks for rivets, and, moreover, the best and most affordable, in almost unlimited quantities quantity.

Obtaining a connection using such rivets is simple. It is more convenient for this to prepare rivets of the required length in advance, melting the head of the plastic rod on one side. To connect two parts with plastic rivets, we overlap the parts and melt them with the same burner, forming a hole. the desired profile and sizes, insert a rivet there and, by melting, form a head from the opposite end of the rivet rod. After practicing reflowing several times, the head turns out neat and tear-resistant.

Let's get started...

To implement the idea it is necessary raw material in the form of a part of a milk plastic bottle (Fig. 1a) which is cut along the circumference into two components (Fig. 2 and Fig. 3, respectively). A trunk will be formed from the part adjacent to the neck (Fig. 1b), and branches of the future New Year tree will be cut out from the ring with a central groove (Fig. 1c). One whole plastic bottle produces two or three rings. The more rings you prepare, the fluffier and taller the Christmas tree you can assemble. I had at least 20 of these rings (10 full bottles).

Plastic rings with a groove in the middle need to be cut into several equal parts(Fig. 2) along the generatrices of the bottle cylinder. As a result, we get convex rectangles. If you cut into 2 parts, then from such long halves you will get long lower branches of the Christmas tree, if you cut into 3 equal parts, you will get branches of medium tiers and medium length, and cutting into 4-5 parts, you get small blanks for the upper tiers of a tabletop Christmas tree . It is not at all necessary to observe particular uniformity in the dimensions of the rectangles for one type of tiers.

Next begins the rather tedious work of forming the branch. From each plastic convex rectangle (Fig. 3a), a wedge-shaped blank should be cut out with scissors (Fig. 3b). The axis of symmetry of the wedge-shaped part should be located along the corrugation groove. Immediately after cutting the workpiece, “needles” should be formed on it, making cuts along the side edges at approximately 45 degrees to the groove and radially at the end of the “branch”. (Fig. 3c). The needles are alternately moved out from the plane of the workpiece, also at 45 degrees to each other. Placing the needles up and down relative to the plane of the branch provides fluffiness to the Christmas tree.

As a result of such painstaking work, several sets (Fig. 4) of branches are obtained different sizes for desktop homemade Christmas tree. Cutting branches and then needles is quite a long task, but you can entrust this to your family as part of a collective creativity to decorate life under New Year. It should be noted that it is difficult to accurately determine the number of branches forming a specific tier by eye, so you should always have several rings in stock (Fig. 1c) for cutting branches during the installation of tiers

The place for attaching branches is the trunk, which consists of several parts (logs). The top parts of plastic bottles (Fig. 1b) were considered waste during the separation of the rings (Fig. 1c), but now they are also used in tree making to create a trunk. The base of the trunk and the lower log is the full neck part of a plastic bottle (Fig. 5a). The upper logs are assembled from blanks obtained by cutting off the threaded part of a milk bottle with a flange, as well as removing a segment of plastic along the generatrices (Fig. 5b, 5c). The segments need to be rolled into a tube and secured on both sides with plastic rivets. In a similar way, it is necessary to create several logs to attach tiers of branches. In my case, these are 3 logs, but there could be more or less. For a miniature Christmas tree, 3-4 tiers of branches on just one log are enough.

Naturally, the diameter of the trunk should taper towards the top of the tabletop tree and the diameter of the upper log should be smaller than the lower one. The larger the cut of the segment, the higher the log obtained from the conical top of the plastic bottle. For the top you need a half segment, and for the middle part about two-thirds of the whole neck (Fig. 5b). The diameter of the lower hole of the upper log should be approximately 1 mm larger than the upper hole of the lower log forming the trunk.

It's time to attach the branches to the "logs". Each log will need to place 2-3 tiers of branches. The small number of tiers does not allow effectively covering the rivet heads with branches, and a large number of spoils the aesthetic appearance of the Christmas tree. In each tier of this design you can install from 4 to 10 branches. Fastening is carried out using plastic rivets, since you will need quite a lot of plastic rivets, it is better to prepare them for future use. The easiest way is to place the branches in tiers on the lower logs (Fig. 6), since the neck of the plastic bottle is wide enough and it is convenient to hold the plastic rivet with inside finger.

If you place the branches closely along the circumference of the tier, then one rivet is enough to attach the branch to the trunk (Fig. 6-8). For those who like greater reliability, they can install two rivets side by side. The tiers of branches must be formed like the roof deck of a house - from the bottom up, then the branches of the upper tier will cover the rivets of the lower one and the heads of the rivets will be completely invisible.

In my case, in the lower (Fig. 6) and middle (Fig. 7) log of the trunk there are 2 tiers of branches, and in the upper one - 3 (Fig. 8). There are 5 tiers of branches in total. It’s quite enough to look amazingly similar to a real tree. Installation of plastic rivets on upper tier, due to its small diameter, should be done using tweezers or a medical clamp.

After securing all tiers to all logs, you can begin final assembly. But first it is advisable to decide on the top. In my case, without thinking for a long time, I built the top using the same technology as the trunk (Fig. 5), that is, by rolling the plastic into a cone. But you can do this in another way, for example, in the form of an asterisk or a ball (I like the cone better). The top of the tree is attached to the upper element of the trunk also using a rivet, installed from the inside and melted from the outside. Top part trunk, together with the top, already has a miniature tabletop Christmas tree itself (Fig. 9). You can install it on your monitor and enhance the holiday feeling...

A living Christmas tree grows from the bottom up, in the same order, and we collect logs with tiers of branches by adding “logs” (Fig. 10) to the already existing Christmas tree. It is better to connect the trunk elements together in a place covered by a branch, at three points along the circumference of the trunk. In this case, the trunk becomes rigid and will not break if the Christmas tree accidentally falls to the floor from the table, the Christmas tree is a tabletop one...

And if you insert a dynamic light part (for example, a garland) inside the Christmas tree, then New Year's Eve she will amaze those around her with her charm:

Here is such a master class. Of course, it’s a little complicated, but what a beauty it turns out!

We consider green plastic bottles to be just trash. But in new year holidays and in in capable hands they can turn into real forest beauties! The tree does not have to be live or purchased for a lot of money. In this article you will get acquainted with several options for creating a Christmas tree from plastic bottles with your own hands.

Tall artificial tree

From plastic bottles you can make not just a small craft, but a real tree that can be decorated. To do this you need to prepare a steel rod. Its length is equal to the height of the finished tree, it is best to take a piece of 0.5 m. Do not forget about the thickness of the rod, the structure must be stable. The ideal diameter is at least 5 mm. Also prepare a single-core aluminum wire, green plastic bottles (at least 30 pieces), scissors, hot glue and a craft stand.

To make the spruce, you only need the cylindrical part of the bottles, so cut off the neck and bottom of all of them at once. Carefully cut the resulting cylinders in a spiral.

You should get strips 2 cm wide. Now bend one edge about 5 mm, this will allow you to set the correct direction of the needles. Cut the fringe at 1mm intervals. You need a lot of fringe!

Christmas tree: large craft

When the blanks are made, proceed directly to creating the tree. Start from the top. Wind a strip about 8 cm around the rod and secure with a glue gun. Now roll up a small piece of fringe and glue it inside the cylinder on the rod. Then we wrap the fringe onto a strip of plastic and glue it. When a piece of fringe runs out, just take the next one and continue gluing. The top of the Christmas tree made from plastic bottles is ready!

Let's start creating branches. The top ones are the shortest (about 6 cm). Bend the frame from the wire (a ring and three beams extending to the sides). Place it on the rod. Wrap the frame with fringe.

We are finishing work on a large spruce tree

When the first tier is ready, wrap the space underneath with fringe and move on to the second tier. It will consist of four branches, each of which has two small branches. The length of the branches is about 9 cm. Wrap the frame and the second spacer piece with plastic pine needles.

The branches of the third tier should be about 10 cm long, the lowest - 15 cm. But four tiers of the “New Year Tree” craft are not the limit. You can make the spruce much taller. The main thing is to make each tier wider and more branched.

All that remains is to make a stand. You can make it yourself from two planks or buy it ready-made in the store. Well, don’t forget to dress up the plastic beauty with beautiful New Year’s toys. This craft requires perseverance and patience, but the result will please you very much!

Tall Christmas tree made from plastic bottles: instructions

If you are an amateur creative jewelry interior design or just want your child to take it to school, kindergarten For a wonderful craft for an exhibition dedicated to the New Year, make a Christmas tree like this from PET. Prepare approximately 35 bottles, scissors, candles, a pot and a plastic tube.

35 green bottles are enough for a craft about 1.2 meters high.

Cut off the bottom of all bottles and cut the plastic along almost to the neck into strips 1.5 cm wide.

Now it’s time for the not-so-pleasant stage of creating a Christmas tree from plastic bottles with your own hands. Carry it out in a ventilated area. You need to pass each strip on each bottle over a candle flame every 2 cm. This will take time. Afterwards, heat each bottle over a candle and straighten the segments like the rays of the sun.

Attach a plastic tube to the base and place your workpieces on it. Now use scissors to trim the spruce so that it has a cone shape. This craft looks good on summer cottage, especially dusted with snow. But if you dress it up with tinsel and toys, a fluffy plastic spruce will decorate your apartment.

Small Christmas tree made of PET

You can decorate a table or shelf with a small craft. It doesn’t take as much time to make it as previous Christmas trees. And you only need six bottles. Also take plasticine, green paint, a brush, scissors, a 50 cm long rod and a pot. Cut the PET approximately in half and discard the bottom part. Cut the parts with the neck into 8 teeth, each of which is cut diagonally. Bend the strips upward, like the paws of a spruce tree. Paint the resulting blanks in green color and dry.

Strengthen the rod in the pot and use plasticine to strengthen the legs of your spruce one by one.

Trim the top branches. Then decorate the tree. Now you know how to make a Christmas tree from a plastic bottle. Naturally, such a tree does not look like a real one, but how many joyful moments can be given to children while working on a craft!

Christmas tree from two bottles

Above are crafts from a fairly large number plastic containers. How can you make a Christmas tree from plastic bottles with your own hands if you don’t have a lot of them? Take two bottles, a sheet of paper, scissors and tape.

Cut off the neck and bottom of the bottles. Roll a piece of paper into a tube and insert it into the neck. Secure the upper end with tape, otherwise the tube will unwind. Be sure to trim the cut so that the craft stands firmly on the surface. Cut the remaining parts of the bottle into rings about 8 cm wide. Make a fringe out of them, without cutting 1 cm to the edge. The thinner the strips, the fluffier the spruce. Let all the stripes be equal in width, it looks neat. Attach the fringe to the paper stem using tape, starting with the widest strip.

After completing the formation of the spruce, decorate its top. You can use leftover bottles or a red or gold star. Place mini balls on the branches and the spruce is ready!

Original Christmas tree

Such an intricate craft will decorate the table during the New Year holidays, and during the rest of the year it can easily keep you company indoor plants on the windowsill. Take one plastic bottle, scissors, candle, cork plug, a cup of baby yogurt or cottage cheese, glue and foam rubber (you can use a dishwashing sponge). Cut the bottle into squares of different sizes, from which you can then make stars (preferably not five-pointed ones). Thickly cut the ends of the stars into the fringe with scissors.

Then bring the edges of the blanks to the candle flame for a couple of seconds, so they will curl upward beautifully. Cut the foam into small pieces. Lubricate the largest piece with glue and attach a piece of sponge, place the next piece of plastic on top. Thus, assemble the craft completely. This DIY Christmas tree made from plastic bottles resembles a children’s pyramid in its assembly technique.

Then cut a bucket out of the cup and place a cork inside - this is the trunk of our tree. Glue the tree to the cork and the job is finished.

This is how you can create a real miracle from ordinary plastic bottles!

A DIY Christmas tree made from plastic bottles can be a great surprise for the New Year and Christmas holidays. This article will describe various ways making such a craft.

Materials and tools

First, let's look at the materials and tools that will be needed in the process of making such a magnificent decoration as a Christmas tree made from plastic bottles with your own hands. This list includes the following items:

Plastic bottles. Preferably green: after all natural color Christmas trees - green. But any other is possible. In this case, you will have to purchase additional green paint and with its help properly design the final craft.

Stationery scissors and a knife for cutting plastic bottles.

Black marker for marking.

Glue and tape.

Wire.

Steel pipe.

Electric drill with drill bit.

Cardboard or Whatman paper.
Markers, pencils and paints.

Methods

There are several ways to make a Christmas tree with your own hands from plastic bottles. It could be:

Method one: big Christmas tree

This DIY Christmas tree made from plastic bottles is made from a fairly large amount of containers. Therefore, before starting work, it is necessary to collect an impressive supply of such bottles. There are two ways to create such a craft. The first of them consists of the following sequence:

We take a metal pipe of the required length and install it in the ground at the place where the Christmas tree is collected using a hammer.

Then, step by step, around this pipe we make circles of the “lower tier of the tree” from plastic bottles that fit tightly to each other. We fix them with tape.

Similarly, we create the next tiers of our tree and fix them using tape. We also take into account that with each subsequent tier the diameter of the formed circle decreases. That is, you should get a cone that looks like a New Year's beauty.

The topmost tier of the tree should consist of only one bottle mounted on a metal pipe.

Then you need to decorate the tree properly.

The key disadvantage of this method is that the New Year's beauty turns out to be motionless. Not everyone likes it. Therefore, some craftsmen use the second method, which consists of the following steps:

As in the previous case, we install the central load-bearing frame from metal pipe using a hammer at the place where the craft is created.

Using electric drill We drill holes in the pipe at the level of each tier of the tree.

IN drilled holes We install a straight wire, the length of which is equal to the diameter of the tier. Then we make a circle from the same wire. Again, the diameter of each is more than high level is reduced so that the end result is a cone.

We make the upper part from a single plastic bottle, which we put on the free end of a metal pipe.

Then we make a hole in the cap of each bottle into which we install a wire hook, which is then fixed on the ring.

Filling each of the tiers of the tree, we get final result- New Year's beauty.

At the next stage we decorate the Christmas tree.

Unlike the first case, here the bottles hang on a ring and can move.

Option two: a small Christmas tree on the table

You don't always need a big one Christmas tree from plastic bottles, as in the previous case. Then you can make a miniature beauty from a green plastic container with a capacity of 2 liters. The algorithm for making a Christmas tree in this case is as follows:

We retreat about 3 cm from the bottom of the neck of the bottle and use a stationery knife to cut off its upper part.

Then we roll up a sheet of whatman paper and place it in the neck. We fix this entire structure with tape. The frame of the Christmas tree is ready.

At the next stage, cut off the bottom of the container, and cut the rest into rings 3-4 cm wide.

Then we cut the bottom of each ring into thin strips, but leave the top untouched. After this, we cut the ring itself into 2 equal parts and screw it to whatman paper. Don't forget to use tape to secure it. So, step by step, we turn whatman paper into green branches and get a miniature New Year's beauty. We leave the top of the tree sharp and fix it with the same tape.

Another way

In the form of a three-dimensional applique, you can make a Christmas tree from plastic bottles with your own hands (photos of some crafts, by the way, are presented in the review). In this case, we take a sheet of cardboard or whatman paper as a basis. required sizes. Then we take 3-4 plastic bottles and mark them in the form of a three-dimensional model of a Christmas tree. For example, these could be triangles or trapezoids. Using stationery scissors and a knife, cut according to the markings of the model. Then we glue them to the base with glue. Then we properly design a sheet of cardboard or whatman paper. When finished, you can add a frame to this craft, and it will become an excellent decoration for your home.

Decorating the craft

Any DIY Christmas tree made from a plastic bottle must be decorated at the final stage. For these purposes, you can also use the usual glass toys, and garlands, and other available materials. In general, we do not limit the flight of imagination and use everything we deem necessary.

Summary

This article describes three main ways to make a Christmas tree from plastic bottles with your own hands. Each of them is strictly suitable for one specific situation. The simplest is the last, third, which allows you to create a three-dimensional image of a Christmas tree. The most difficult is the first one. It requires a lot of material and is not that easy to implement.

Make a hole in the left bottom, which you secure to the lower end of the stick using a plastic bottle cap (you can hammer a nail in for strength).

Place the last, smallest piece, neck up, on the upper end of the stick and screw the green plug onto the neck, also securing it with a nail for strength.

A little patience, perseverance, effort and the forest beauty is ready!

These Christmas trees can be used as New Year's decorations for your homes!

To make a decorative New Year's craft: a Christmas tree from plastic bottles, you will need the following:

Plastic bottles - 3 pcs;
Scotch;
A sheet of thick paper, ideally whatman paper (A4);
Scissors;

	So, cut the bottle as shown in the photo. That is, it is necessary to cut off the bottom and neck so that a straight pipe from the bottle remains.
	Next you need to make blanks for the branches. In order for the tree to have a cone-shaped shape, the blanks must have different sizes. That is, you need to achieve the following:
	Cut each plastic bottle lengthwise into 3 equal parts and then adjust their sizes so that each subsequent tier is slightly smaller than the previous one. Then each workpiece must be “dissolved into needles.” The neck of one of the bottles will serve as a stand for our future New Year's craft.
	The next step is to roll the Whatman paper into a tube. We insert it into the bottleneck...
	...and secure with tape.
	Now all that remains is to fix each tier of the tree with tape in a circle and a little New Year's craft: the Christmas tree with your own hands is ready!
	You can decorate the top of our New Year's tree with a homemade Christmas tree toy, or complete the Christmas tree the way we did.
	If you want to make a Christmas tree from plastic bottles more fluffy, like in the photo, when making the Christmas tree, you need to cut the needles as thinly as possible (more often).
	By the way, the Christmas tree also looks quite creative with larger “branches” - master class from the website Country of Masters. We cut the bottle in the same way as in the previous version into 3 parts. Only we make cuts in a circle towards the center, straight.
	A puncture is made in the center with an awl and the needles are bent up and down in order. A puncture is made in the lid of the cream or mineral water into which a skewer of the required length is inserted.
	The parts are strung in descending order, with a large bead placed on top of the glue. The Christmas tree can be decorated with polystyrene foam, rain, etc.
	Glue the Christmas tree onto the disk stand. The Christmas tree is ready!
	You can put gifts or plant an animal nearby. These Christmas trees have been a constant success for many years.

Method 3. And finally, the last option for today is a Christmas tree made from plastic milk bottles (what decorative New Year trees are not made from...). The design is completely collapsible, has the maximum resemblance to the original, does not require particularly complex technologies or specific work skills, there are no problems with bottles either, and a holiday is just around the corner...

Materials and tools

In addition to bottles, you only need scissors and plastic rivet technology

Plastic rivets

1. Empty ballpoint pen refills. Fairly accessible material. They are good because they are colorless and the compound, with their help, turns out to be organically integrated into the product made from plastic bottles. Such a rivet turns out neat, with a round head, however, it has a slightly reduced tensile strength. In addition, the rod from ballpoint pens is round in cross-section and completely fills the drilled hole in the parts being connected. By the way, the walls of the rods come in different thicknesses; for rivets it is better to use rods with thicker walls.

2. Chupa Chups sticks. Similar to option No. 1 only in color. The connection is more cumbersome, and the rivet head melts with difficulty (it either burns, becomes ugly, or unreliable).

3. The most ideal option, and very convenient (I give the world a proposal) is to use material from buckets with construction mixtures of 3, 5, 10 liters. There are quite a lot of them left after repairs, and one lasts for a long time.

Obtaining a connection using such rivets is simple. It is more convenient for this to prepare rivets of the required length in advance, melting the head of the plastic rod on one side. To connect two parts with plastic rivets, we overlap the parts, melt them with the same burner, forming a hole of the desired profile and size, insert a rivet there and, by melting, form a head from the opposite end of the rivet rod. After practicing reflowing several times, the head turns out neat and tear-resistant.

Let's get started...

To implement the idea, a source material is required in the form of a part of a plastic milk bottle (Fig. 1a), which is cut along the circumference into two components (Fig. 2 and Fig. 3, respectively). A trunk will be formed from the part adjacent to the neck (Fig. 1b), and branches of the future New Year tree will be cut out from the ring with a central groove (Fig. 1c). One whole plastic bottle produces two or three rings. The more rings you prepare, the fluffier and taller the Christmas tree you can assemble. I had at least 20 of these rings (10 full bottles).

Plastic rings with a groove in the middle need to be cut into several equal parts (Fig. 2) along the forming elements of the bottle cylinder. As a result, we get convex rectangles. If you cut into 2 parts, then from such long halves you will get long lower branches of the Christmas tree, if you cut into 3 equal parts, you will get branches of medium tiers and medium length, and cutting into 4-5 parts, you get small blanks for the upper tiers of a tabletop Christmas tree . It is not at all necessary to observe particular uniformity in the dimensions of the rectangles for one type of tiers.

As a result of such painstaking work, several sets (Fig. 4) of branches of different sizes are obtained for a desktop homemade Christmas tree. Cutting out branches and then needles is quite a long task, but you can entrust this to your family as part of a collective creativity in decorating life for the New Year. It should be noted that it is difficult to accurately determine the number of branches forming a specific tier by eye, so you should always have several rings in stock (Fig. 1c) for cutting branches during the installation of tiers

It's time to attach the branches to the "logs". Each log will need to place 2-3 tiers of branches. A small number of tiers does not allow you to effectively cover the heads of the rivets with branches, and a large number spoils the aesthetic appearance of the Christmas tree. In each tier of this design you can install from 4 to 10 branches. Fastening is carried out using plastic rivets, since you will need quite a lot of plastic rivets, it is better to prepare them for future use. The easiest way is to place the branches in tiers on the lower logs (Fig. 6), since the neck of the plastic bottle is wide enough and it is convenient to hold the plastic rivet on the inside with your finger.

In my case, in the lower (Fig. 6) and middle (Fig. 7) log of the trunk there are 2 tiers of branches, and in the upper one - 3 (Fig. 8). There are 5 tiers of branches in total. It’s quite enough to look amazingly similar to a real tree. Installation of plastic rivets on the upper tier, due to its small diameter, should be done using tweezers or a medical clamp.

After securing all tiers to all logs, you can begin final assembly. But first it is advisable to decide on the top. In my case, without thinking for a long time, I built the top using the same technology as the trunk (Fig. 5), that is, by rolling the plastic into a cone. But you can do this in another way, for example, in the form of an asterisk or a ball (I like the cone better). The top of the tree is attached to the upper element of the trunk also using a rivet, installed from the inside and melted from the outside. The upper part of the trunk, together with the top, is itself a miniature tabletop Christmas tree (Fig. 9). You can install it on your monitor and enhance the holiday feeling...

And if you insert a dynamic light part (for example, a garland) inside the Christmas tree, then on New Year’s Eve it will amaze those around you with its charm:

Here is such a master class. Of course, it’s a little complicated, but what a beauty it turns out!