DIY Christmas tree made from plastic bottles. Creative Christmas trees made from plastic bottles - Irzeis - LJ. Christmas tree made of fabric and threads

We consider green plastic bottles to be just trash. But on New Year's holidays and in capable hands they can turn into real forest beauties! The tree does not have to be live or purchased for a lot of money. In this article you will get acquainted with several options for creating a Christmas tree from plastic bottles with your own hands.

Tall artificial tree

From plastic bottles you can make not just a small craft, but a real tree that can be decorated. To do this you need to prepare a steel rod. Its length is equal to the height of the finished tree; it is best to take a piece of 0.5 m. Do not forget about the thickness of the rod; the structure must be stable. The ideal diameter is at least 5 mm. Also prepare a single-core aluminum wire, green plastic bottles (at least 30 pieces), scissors, hot glue and a craft stand.

To make the spruce, you only need the cylindrical part of the bottles, so cut off the neck and bottom of all of them at once. Carefully cut the resulting cylinders in a spiral.

You should get strips 2 cm wide. Now bend one edge about 5 mm, this will allow you to set the correct direction of the needles. Cut the fringe at 1mm intervals. You need a lot of fringe!

Christmas tree: large craft

When the blanks are made, proceed directly to creating the tree. Start from the top. Wind a strip about 8 cm around the rod and secure with a glue gun. Now roll up a small piece of fringe and glue it inside the cylinder on the rod. Then we wrap the fringe onto a strip of plastic and glue it. When a piece of fringe runs out, just take the next one and continue gluing. The top of the Christmas tree made from plastic bottles is ready!

Let's start creating branches. The top ones are the shortest (about 6 cm). Bend the frame from the wire (a ring and three beams extending to the sides). Place it on the rod. Wrap the frame with fringe.

We are finishing work on a large spruce tree

When the first tier is ready, wrap the space underneath with fringe and move on to the second tier. It will consist of four branches, each of which has two small branches. The length of the branches is about 9 cm. Wrap the frame and the second spacer piece with plastic pine needles.

The branches of the third tier should be about 10 cm long, the lowest - 15 cm. But four tiers of the “New Year Tree” craft are not the limit. You can make the spruce much taller. The main thing is to make each tier wider and more branched.

All that remains is to make a stand. You can make it yourself from two planks or buy it ready-made in the store. Well, don’t forget to dress up the plastic beauty with beautiful New Year’s toys. This craft requires perseverance and patience, but the result will please you very much!

Tall Christmas tree made from plastic bottles: instructions

If you are an amateur creative jewelry interior design or just want your child to take it to school, kindergarten For a wonderful craft for an exhibition dedicated to the New Year, make a Christmas tree like this from PET. Prepare approximately 35 bottles, scissors, candles, a pot and a plastic tube.

35 green bottles are enough for a craft about 1.2 meters high.

Cut off the bottom of all bottles and cut the plastic along almost to the neck into strips 1.5 cm wide.

Now it’s time for the not-so-pleasant stage of creating a Christmas tree from plastic bottles with your own hands. Carry it out in a ventilated area. You need to pass each strip on each bottle over a candle flame every 2 cm. This will take time. Afterwards, heat each bottle over a candle and straighten the segments like the rays of the sun.

Attach a plastic tube to the base and place your workpieces on it. Now use scissors to trim the spruce so that it has a cone shape. This craft looks good on summer cottage, especially dusted with snow. But if you dress it up with tinsel and toys, a fluffy plastic spruce will decorate your apartment.

Small Christmas tree made of PET

You can decorate a table or shelf with a small craft. It doesn’t take as much time to make it as previous Christmas trees. And you only need six bottles. Also take plasticine, green paint, a brush, scissors, a 50 cm long rod and a pot. Cut the PET approximately in half and discard the bottom part. Cut the parts with the neck into 8 teeth, each of which is cut diagonally. Bend the strips upward, like the paws of a spruce tree. Paint the resulting blanks in green color and dry.

Strengthen the rod in the pot and use plasticine to strengthen the legs of your spruce one by one.

Trim the top branches. Then decorate the tree. Now you know how to make a Christmas tree from a plastic bottle. Naturally, such a tree does not look like a real one, but how many joyful moments can be given to children while working on a craft!

Christmas tree from two bottles

Above are crafts from a fairly large number plastic containers. How can you make a Christmas tree from plastic bottles with your own hands if you don’t have a lot of them? Take two bottles, a sheet of paper, scissors and tape.

Cut off the neck and bottom of the bottles. Roll a piece of paper into a tube and insert it into the neck. Secure the upper end with tape, otherwise the tube will unwind. Be sure to trim the cut so that the craft stands firmly on the surface. Cut the remaining parts of the bottle into rings about 8 cm wide. Make a fringe out of them, without cutting 1 cm to the edge. The thinner the strips, the fluffier the spruce. Let all the stripes be equal in width, it looks neat. Attach the fringe to the paper stem using tape, starting with the widest strip.

After completing the formation of the spruce, decorate its top. You can use leftover bottles or a red or gold star. Place mini balls on the branches and the spruce is ready!

Original Christmas tree

Such an intricate craft will decorate the table during the New Year holidays, and during the rest of the year it can easily keep you company indoor plants on the windowsill. Take one plastic bottle, scissors, candle, cork plug, a cup of baby yogurt or cottage cheese, glue and foam rubber (you can use a dishwashing sponge). Cut the bottle into squares different sizes, from which then make stars (preferably not five-pointed ones). Thickly cut the ends of the stars into the fringe with scissors.

Then bring the edges of the blanks to the candle flame for a couple of seconds, so they will curl upward beautifully. Cut the foam into small pieces. Lubricate the largest piece with glue and attach a piece of sponge, place the next piece of plastic on top. Thus, assemble the craft completely. This DIY Christmas tree made from plastic bottles resembles a children’s pyramid in its assembly technique.

Then cut a bucket out of the cup and place a cork inside - this is the trunk of our tree. Glue the tree to the cork and the job is finished.

This is how you can create a real miracle from ordinary plastic bottles!

In anticipation New Year's holidays many craftswomen wonder about unusual crafts. We would like to offer interesting ideas for New Year's crafts. It will be easy to complete them based on step-by-step master classes. All materials can be easily purchased in stores.

Christmas tree made from bottles

This plastic beauty will decorate your home and create Christmas mood to all its residents. A DIY Christmas tree made from plastic bottles is made from any plastic containers. The size of the bottles does not matter, and the color scheme can be different, because you can’t always find a Christmas tree that is only green.

Materials:

• Plastic - bottles 2 pcs.
• Green paper 30 by 40 cm - 1 sheet.
• Scotch.
• Scissors.

Having prepared everything necessary materials, you can start making a Christmas tree from plastic bottles with your own hands.

If you want to make the tree taller and larger, then feel free to take more material to work with. There are no limits to imagination and restrictions on creativity.

Another creation option

There are many master classes on how to make a Christmas tree from plastic bottles. Let's talk in detail about another method.

Materials:

Step-by-step instruction

Let us immediately note that All bottle necks and bottoms will need to be cut off. They will not be needed during the Christmas tree making process.

We assemble the tree and insert it into the base, now you can shape the branches in any direction and, of course, decorate it Christmas balls, garlands. It is worth noting that the balls can also be homemade.

Christmas tree made from cups

A New Year's tree can be made not only from plastic bottles; cups are also perfect for this.

Materials for work:

• Green plastic cups.
• Stapler.
• Glue gun.
• Pasta bows.
• Silver thread.
• Ribbons.
• Tinsel.

Algorithm for performing the work:

Now all that remains is to decorate the Christmas tree. Inside each glass we glue pasta bows hanging on silver threads. Glue rhinestones or beautiful shiny beads to the middle of the pasta.

The Christmas tree needs to be placed on a leaf thick cardboard, decorate the bottom with tinsel. Insert a star into the top glass. Or you can take a battery-powered garland and thread it inside the tree through the top glass, making a hole in it. We hide the battery pack in a glass and cover it with a star or tip on top. When you turn on the garland, the tree will glow in different colors.

Hanging decoration

When decorating the interior of your home, you can bring to life a lot of interesting ideas for crafts. Pay attention to this master class.

Materials:

• 28 plastic glasses green tint.
• The shiny ribbon is not wide.
• Stapler.
• Glue.
• Plastic balls of small diameter.
• Scotch.

Step-by-step instruction:

Using not many materials and without spending a lot of time, we created a beautiful and original Christmas tree to decorate the interior. It can easily be placed in any corner of the house.

Garland made from scrap materials

In addition to homemade Christmas trees, you can decorate your house with a chic garland made of plastic glasses. Meet someone like this unusual decor in a festive interior it is extremely rare, because many people don’t even imagine what can be done from ordinary plastic glasses.

Materials:

Completing of the work:

That's all. A beautiful and unusual garland for the New Year's interior is ready.

Garland-ball. You can make a garland in the shape of a ball. For production you will need:

• Transparent plastic glasses - 50 units.
• Garland with fifty LEDs.
• Clothespins - 3 pcs.
• Stapler.

Step-by-step instruction:

This unusual ball is perfect for creating a wonderful atmosphere at home or for dancing at a party.

Attention, TODAY only!

At the bottom there should be the largest bottles (2 and 1.5 liters, in the middle - liter bottles, and at the top 0.5 and 0.3 liter bottles. If you have bottles of the same volume, then adjust the length of the “branches” yourself by cutting stripes up required length.

Make a hole in the left bottom, which you secure to the lower end of the stick using a plastic bottle cap (you can hammer a nail in for strength).

Place the last, smallest piece, neck up, on the upper end of the stick and screw the green plug onto the neck, also securing it with a nail for strength.

A little patience, perseverance, effort and the forest beauty is ready!

Such Christmas trees can be used as New Year's decoration your houses!

Method 2. To make such a Christmas tree you need a minimum of time and expense. A master class on making a Christmas tree from plastic bottles will tell you in detail how to make such an original New Year's craft.

To make a decorative New Year's craft: a Christmas tree from plastic bottles, you will need the following:

1. Plastic bottles - 3 pcs;
2. Scotch;
3. Sheet thick paper, ideally whatman paper (A4);
4. Scissors;

Method 3. And finally last option for today - a Christmas tree made from plastic milk bottles (what decorative New Year trees are not made from...). The design is completely collapsible, has maximum resemblance to the original, does not require special complex technologies and specific work skills, there are no problems with bottles either, and a holiday is just around the corner...

Materials and tools

The material for making the Christmas tree is a milk plastic bottle or part of it (Fig. 1). To make a homemade tabletop Christmas tree, you will need 5-20 milk/kefir plastic bottles with corrugation at the bottom. The number of bottles determines the number of branches and tiers. The more branches, the more fluffy the Christmas tree is; the more tiers, the taller it is.

In addition to bottles, you only need scissors and plastic rivet technology

Plastic rivets

To implement the technology of plastic rivets, it is necessary to have a means for melting (installing) the rivets and the rivet itself. You need to manage to melt the head of the rivet using a hot nail or lighter. You can do this in the same way with a well-heated soldering iron. In addition, you will need clamps and tweezers to install rivets in hard-to-reach places.

For plastic rivets, it is very important to choose the material. After fumbling for about a year, through trial and error, taking into account the requirements of strength and availability, I identified several sources for obtaining plastic rivets:

1. Empty ballpoint pen refills. Enough available material. They are good because they are colorless and the compound, with their help, turns out to be organically integrated into the product made from plastic bottles. Such a rivet turns out neat, with a round head, however, it has a slightly reduced tensile strength. In addition, the rod from ballpoint pens is round in cross-section and completely fills the drilled hole in the parts being connected. By the way, the walls of the rods are different thicknesses, for rivets it is better to use rods with thicker walls.

2. Chupa Chups sticks. Similar to option No. 1 only in color. The connection is more cumbersome, and the rivet head melts with difficulty (it either burns, becomes ugly, or unreliable).

3. The most perfect option, and very convenient (I give the world a suggestion) to use material from buckets with construction mixtures for 3, 5, 10 liters There are quite a lot of them left after repairs, and even one lasts for a long time.

From the walls of such a bucket you need to cut a ring, and cut the ring along the generatrix (this is the only way) into strips 2...4 mm wide, length from 4 to 15 cm. These will be the blanks for rivets, and, moreover, the best and most affordable, in almost unlimited quantities quantity.

Obtaining a connection using such rivets is simple. It is more convenient for this to prepare rivets of the required length in advance, melting the head of the plastic rod on one side. To connect two parts with plastic rivets, we overlap the parts and melt them with the same burner, forming a hole the desired profile and sizes, insert a rivet there and, by melting, form a head from the opposite end of the rivet rod. After practicing reflowing several times, the head turns out neat and tear-resistant.

Let's get started...

To implement the idea it is necessary raw material in the form of a part of a milk plastic bottle (Fig. 1a) which is cut along the circumference into two components (Fig. 2 and Fig. 3, respectively). A trunk will be formed from the part adjacent to the neck (Fig. 1b), and branches of the future will be cut out from the ring with a central groove (Fig. 1c). Christmas tree. One whole plastic bottle produces two or three rings. The more rings you prepare, the fluffier and taller the Christmas tree you can assemble. I had at least 20 of these rings (10 full bottles).

Plastic rings with a groove in the middle need to be cut into several equal parts(Fig. 2) along the generatrices of the bottle cylinder. As a result, we get convex rectangles. If you cut into 2 parts, then from such long halves you will get long lower branches of the Christmas tree, if you cut into 3 equal parts, you will get branches of medium tiers and medium length, and cutting into 4-5 parts, you get small blanks for the upper tiers of a tabletop Christmas tree . It is not at all necessary to observe particular uniformity in the dimensions of the rectangles for one type of tiers.

Next begins the rather tedious work of forming the branch. From each plastic convex rectangle (Fig. 3a), a wedge-shaped blank should be cut out with scissors (Fig. 3b). The axis of symmetry of the wedge-shaped part should be located along the corrugation groove. Immediately after cutting the workpiece, “needles” should be formed on it, making cuts along the side edges at approximately 45 degrees to the groove and radially at the end of the “branch”. (Fig. 3c). The needles are alternately moved out from the plane of the workpiece, also at 45 degrees to each other. Placing the needles up and down relative to the plane of the branch provides fluffiness to the Christmas tree.

As a result of such painstaking work, several sets (Fig. 4) of branches of different sizes are obtained for the tabletop homemade Christmas tree. Cutting branches and then needles is quite a long task, but you can entrust this to your family as part of a collective creativity to decorate life under New Year. It should be noted that it is difficult to accurately determine the number of branches forming a specific tier by eye, so you should always have several rings in stock (Fig. 1c) for cutting branches during the installation of tiers

The place for attaching branches is the trunk, which consists of several parts (logs). The top parts of plastic bottles (Fig. 1b) were considered waste during the separation of the rings (Fig. 1c), but now they are also used in tree making to create a trunk. The base of the trunk and the lower log is the full neck part of a plastic bottle (Fig. 5a). The upper logs are assembled from blanks obtained by cutting off the threaded part of a milk bottle with a flange, as well as removing a segment of plastic along the generatrices (Fig. 5b, 5c). The segments need to be rolled into a tube and secured on both sides with plastic rivets. In a similar way, it is necessary to create several logs to attach tiers of branches. In my case, these are 3 logs, but there could be more or less. For a miniature Christmas tree, 3-4 tiers of branches on just one log are enough.

Naturally, the diameter of the trunk should taper towards the top of the tabletop tree and the diameter of the upper log should be smaller than the lower one. The larger the cut of the segment, the higher the log obtained from the conical top of the plastic bottle. For the top you need a half segment, and for the middle part about two-thirds of the whole neck (Fig. 5b). The diameter of the lower hole of the upper log should be approximately 1 mm larger than the upper hole of the lower log forming the trunk.

It's time to attach the branches to the "logs". Each log will need to place 2-3 tiers of branches. The small number of tiers does not allow effectively covering the rivet heads with branches, and a large number of spoils the aesthetic appearance of the Christmas tree. In each tier of this design you can install from 4 to 10 branches. Fastening is carried out using plastic rivets, since you will need quite a lot of plastic rivets, it is better to prepare them for future use. The easiest way is to place the branches in tiers on the lower logs (Fig. 6), since the neck of the plastic bottle is wide enough and it is convenient to hold the plastic rivet with inside finger.

If you place the branches closely along the circumference of the tier, then one rivet is enough to attach the branch to the trunk (Fig. 6-8). For those who like greater reliability, they can install two rivets side by side. The tiers of branches must be formed like the roof deck of a house - from the bottom up, then the branches of the upper tier will cover the rivets of the lower one and the heads of the rivets will be completely invisible.

In my case, in the lower (Fig. 6) and middle (Fig. 7) log of the trunk there are 2 tiers of branches, and in the upper one - 3 (Fig. 8). There are 5 tiers of branches in total. It’s quite enough to look amazingly similar to a real tree. Installation of plastic rivets on upper tier, due to its small diameter, should be done using tweezers or a medical clamp.

After securing all tiers to all logs, you can begin final assembly. But first it is advisable to decide on the top. In my case, without thinking for a long time, I built the top using the same technology as the trunk (Fig. 5), that is, by rolling the plastic into a cone. But you can do this in another way, for example, in the form of an asterisk or a ball (I like the cone better). The top of the tree is attached to the upper element of the trunk also using a rivet, installed from the inside and melted from the outside. Top part trunk, together with the top there is already a miniature table Christmas tree(Fig.9). You can install it on your monitor and enhance the holiday feeling...

A living Christmas tree grows from the bottom up, in the same order, and we collect logs with tiers of branches by adding “logs” (Fig. 10) to the already existing Christmas tree. It is better to connect the trunk elements together in a place covered by a branch, at three points along the circumference of the trunk. In this case, the trunk becomes rigid and will not break if the Christmas tree accidentally falls to the floor from the table, the Christmas tree is a tabletop one...

And if you insert a dynamic light part (for example, a garland) inside the Christmas tree, then New Year's Eve she will amaze those around her with her charm:

Here is such a master class. Of course, it’s a little complicated, but what a beauty it turns out!

Make or buy? Pessimists or simply lazy people, of course, will object: why make something out of trash.

But it is worth noting that plastic bottles are excellent ready material for crafts. And, in addition, a person’s hands and head work, imagination seeks solutions, develops logical thinking, you can still make money from this.

We will not invent anything new, but will show interesting ideas and the work of wonderful needlewomen, whose inventions are inexhaustible.

Collecting materials which will be useful for making a Christmas tree from plastic bottles with your own hands:

• plastic bottles with a volume of 1.5-2 liters, ideally green, blue or silver
• scissors
• sharp knife
• thick A4 paper
• narrow tape
• double sided tape
• glue moment or universal
• candle
• ornaments for decoration

First version of the Christmas tree

We do it as in Fig. 1-3. For this:

• Step 1. We collect 2-4 bottles of the same color, or different sizes. The more bottles, the taller the tree will be.
• Step 2. Cutting the bottle sharp knife into 3 parts, separating the neck and bottom.
• Step 3. We use the bottom as a stand; for strength, cover the inside with plasticine, for example, or stick decorative pebbles on top.
• Step 4. We make the barrel out of thick paper, which we roll into a tube and insert into the neck. It is better to fix the free edge of the tube with glue or double-sided tape. For the trunk, you can also pick up a ready-made tube, which you may have lying around on the farm.
• Step 5. We cut the middle part lengthwise, then into rectangles of equal width, from which we will make branches. One bottle will yield 3 rectangles; for a Christmas tree, 9-12 pieces are enough. Every 3 pcs. make the length shorter by a couple of centimeters.
• Step 6. In each workpiece we make fringe needles with scissors, without cutting the strips to the end of 1-1.5 cm. The narrower the stripes, the fluffier the tree will be.
• Step 7 To make the fringe curly, using a dull knife blade, holding it with your thumb, stretch the strips a few pieces at a time, i.e. not all at once. It's not easy, but it will be effective.
• Step 8 All that remains is to attach our branches to the trunk. We begin to wind the longest fringe around the trunk from below, then overlap the next one, securing each branch with tape. And so on to the very top. If the trunk turns out to be longer, just trim it carefully
• Step 9 For the top of the head, you can use one of the blanks, rolled into a tube or other prepared decoration
• Step 10 We decorate the finished Christmas tree as your imagination dictates, but it’s better to let the children do it.

Helpful advice: you can start decorating the Christmas tree at the manufacturing stage. Decorate or cover your workpieces with decorative sparkles and sequins, paint the edge of the fringe, for example, white.

Fig 1 - Option 1 (what should happen)
Fig 2 - Option 1. Manufacturing stages 1-7

Fig 3 - Option 1. Manufacturing stages 8-12
Fig 4 - Herringbone. Option No. 2

That's all, the green Christmas tree from a plastic bottle is ready!

The second version of a Christmas tree made from plastic bottles

For this Christmas tree you will need several plastic bottles, either colored or can be pre-painted. Figure 4 shows all stages of the work.

Step-by-step description of the process:

• Step 1. Using a sharp knife, cut off the bottom of all bottles. We leave one bottom for the base-stand, do not throw away the rest, they will be useful for other ideas.
• Step 2. We cut the upper part into approximately equal strips 2-3 cm wide, without cutting to the end of the neck. The result was twigs. It is clear that the more bottles, the taller your beauty will turn out.
• Step 3. Next, on each branch we make parallel cuts on both sides, i.e. imitation of needles, which we bend in a chaotic manner. Looks like it turned out like fir branches? Then let's continue.
• Step 4. On the prepared stick-barrel or maybe you have a suitable metal or plastic pipe, we string the bottles sequentially. All neck down and start with the largest one if you have them of different sizes. No glue or tape, tightly to each other.
• Step 5. We make the stand, as in the previous model of the Christmas tree, with some nuances:
  - we take into account that the structure will be heavier - once;
  - on the ends of the barrel, we fasten the plugs so that it does not jump out of the hole, and on the other side, in order to secure all the bottles put on - two.

You may have to use male help and ingenuity.
Here is another version of the Christmas tree, all that remains is to decorate it.

Two original green beauties

The third design option in Fig. 5. The principle of making a Christmas tree from plastic bottles with your own hands, as you understood from the previous options, is similar.

Let's take a quick look features of this option:

1. In this case, the middle of the bottle is cut into squares.
2. Using a prepared stencil, cut out circles from squares.
3. In the middle, use a hot nail to burn holes in each piece.
4. We make strip cuts in a circle, not reaching the middle by about 1 cm.
5. Then the resulting needles can be slightly curled, as in the first option, or melted at some distance above the candle.
6. For the stand, we use the bottom of the bottle, where we also make a hole and insert either a skewer, or sushi chopsticks are perfect.
7. We put the twigs on the resulting trunk, but there is one caveat: you need to come up with some kind of detail to put on between them - it could be a cork, it’s great if you can find large beads with a suitable hole. We decorate either each detail before assembling it, or the finished Christmas tree.

Fourth option Fig. 6.

Fig 5 - Green beauty. Option #3
Fig 6 - Green beauty. Option number 4.

In addition to the above, prepare a cork from wine bottle, a strip of foam rubber, a hard plastic cup.

The action plan is:

1. The first step is all the same as in the previous options - we cut rectangles, then we make various stars out of them - these will be the “paws” of the spruce.
2. Let's hold the resulting pieces over the fire just a little bit so that they bend slightly.
3. We will make multiple cuts at the tips of the “legs” - this will make it more beautiful.
4. Now we will glue a piece of foam rubber to the parts, the result will be a pyramid.
5. The trunk of such a Christmas tree will be a cork plug.
6. Drop a little glue into the glass and attach the cork to the bottom.

The Christmas tree made from plastic bottles is ready, you can give it for the New Year!

Do it yourself christmas tree, cheap, cheerful and, in addition, fast? This is possible, especially if you have some plastic containers - bottles or cups - accumulated in your house.

We present to your attention a double detailed master class: how to make an exclusive New Year’s structure with your own hands from recycled materials.

Master class 1: Christmas tree made from plastic bottles

We will need:

• plastic bottles of different sizes, from 0.3 to 3 liters. Preferably green;
• a wooden stick, the height of which is the same as our Christmas tree. The diameter of the stick should be slightly smaller than the diameter of the neck of the bottles;
• bottle cap;
• stationery knife;
• scissors.

Stage one:

Carefully cut off the bottom of all plastic bottles. Carefully, use a stationery knife - first you need to make a puncture in the wall, and only then saw around the circumference. If sawing with a knife seems difficult, then you can cut with scissors. We leave one large bottom - it will serve as a support on which the Christmas tree will rest. The remaining bottoms can be thrown away.

Stage two:

We cut bottles with sawn-off bottoms into strips 2-2.5 cm wide, naturally, without bringing the cut to the neck. As a result, we get a kind of plastic “flower”.

Stage three:

We cut each strip along the edge, leaving a distance of 0.5 mm between the cuts. These are our “needles”. This way we will be able to make the future Christmas tree “fluffy”. We bend each “needle” - the branches turn out “lush”.

Stage four:

We carefully string the branches onto a stick with our own hands - this is how the Christmas tree is assembled. Wider blanks (from larger-volume bottles) will naturally be at the base, and smaller ones (bottles of smaller capacity) will be at the top. We put the bottom of the bottle on a stick, this will be the base on which the tree rests. We screw the cap on top, you can hammer in a nail for strength.

Christmas tree made from plastic bottles is ready! Decorate! Tinsel, rain and simple matte balls will look great on such a unique New Year's beauty. A garland on an ascetic plastic tree can also look very stylish. Experiment!

Master class 2: how to make a Christmas tree from cups

The most difficult thing in this procedure is perhaps finding green cups.

We will need:

• plastic cups;
• stapler;
• glue;
• toys, balls for decorations.

Stage one:

We place eight cups in the first row with our own hands, in a semicircle. We fasten them with a stapler. Then we put the second row on top - already seven cups. We also fasten them with a stapler. And so on, each row is one glass less. The rows can be lightly glued together for reliability, and also secured with staples. The finished tree should be stable.

Stage two:

Place a toy or ball in each cup. You can drip a little glue so that they are securely fixed inside. By the way, if you have a special glue gun, great, it will help you discreetly attach toys to plastic.

The original Christmas tree made from plastic cups is ready! But if you think that this idea is not creative enough, then here are options for decorating or modifying such a structure with your own hands:

• You can lay out the cups not in a semicircle, but in a circle. Only in this case is it better to “plant” them on a base made of a cardboard cone. Such a tree will have an attractive “facade”, that is, it can be placed in the center of the room, while a semicircular one looks good when standing against the wall.
• If you make a small cut in the top of each cup, you can pass a ribbon through it, secure it with a knot, and hang the decoration on it.
• Macaroni bows painted with golden gouache will look great as decorations.
• You can place a garland inside a round Christmas tree made from cups. It will shine very beautifully through the plastic, and its top light bulb will perfectly replace the traditional star.