How to wash a glossy plastic ceiling. How to clean plastic panels? How to wash plastic panels and what care depends on

Special additives included in cleaning products for interior plastic prevent it from fading.

The undeniable advantage of plastic is its low degree of contamination. However, this material needs cleaning from time to time. In most cases, you can cope with the problem yourself, but sometimes your own efforts, unfortunately, turn out to be in vain, and you have to turn to professionals for help. What do you need to know so that cleaning plastic surfaces does not result in damage to the material? What common mistakes are important to avoid and what cleaning algorithm should you follow?

Plastic surfaces in our Everyday life a lot of. Everywhere you look, you will see this material: shelves, countertops, window sills, children's toys, household equipment, Appliances... When cleaning them, problems may arise that cannot be eliminated. Therefore, it is important to avoid mistakes that often become the reason for the spoiled mood of hundreds of housewives. So, what not to do?

Do not use abrasives - powders, metal sponges.
Solvent and chlorine based cleaning agents must not be used.
It is unacceptable to use sharp metal objects.

As a rule, cleaning plastic is not difficult. Most often, it is enough to arm yourself with liquid detergent and a soft sponge. In tandem with water, they will turn a dirty plastic surface into a clean one. However, if we are talking about deep dirt or scratches, more careful care will be required.

The first rule that will help avoid damage to plastic surfaces is to periodically use special polishes. They will help maintain the product in proper condition and prevent its premature wear.

If yellowness appears on the plastic, it is necessary, first of all, to determine whether it is normal contamination or a change in the structure of the plastic. In the latter case, you cannot do without a plastic restorer. If it is just dirt, it can be easily removed with laundry soap and water or a special cleaning liquid.

To clean plastic, use only soft sponges. No metal objects!

If cleaning the plastic of the car interior is important, it is best to use products that contain special additives. They prevent fading of plastic elements and create a thin “anti-dust” film. This procedure is a mandatory component of dry cleaning of car interiors, which is performed by cleaning companies.

Children's plastic toys, tables, bathtubs are best washed with liquid baby soap diluted in water or a vinegar solution in a ratio of two parts water to one part vinegar. If you need to remove stubborn food stains on plastic kitchen countertops or on furniture facades, apply a paste of baking soda, leave for two hours. Then rub gently and rinse with water.

3 types of cleaning products for plastic surfaces

Professional cleaning companies must have in their arsenal three types of plastic cleaning products, which are specially adapted to the properties of this material. They protect against deformation, cracking and tarnishing, so the plastic lasts for a long time.

Combined formulations. Designed for cleaning plastic and other surfaces (glass, metal, rubber, etc.). With their help, dust, dirt, and minor surface contaminants are eliminated.
Cleaning liquids. They cope with the most difficult stains, old, deeply ingrained stains. At the same time, they are safe for plastic surfaces.
Polishes. Apply on final stage cleansing. Makes small scratches less noticeable and creates protective film preventing the accumulation of dirt. They have a matte or glossy effect.

To clean plastic surfaces of office equipment - printers, copiers and the like - use a special antistatic agent, which is most often produced in the form of aerosols.

It neutralizes electrostatic charges and prevents dust accumulation. These aerosols are suitable for constant use, because they do not contain harmful substances. Unless, of course, we are talking about quality products.

Equipment for cleaning plastic. Is it necessary?

Most often, cleaning plastic is limited to using water, chemical agent and a soft sponge. In some cases, special cleaning equipment can be used to help cope with more severe stains. So, for example, for cleaning plastic blinds you can “connect” a vacuum cleaner with a special brush attachment.

How to clean plastic panels in the bathroom?

Cleaning companies usually have such devices in their arsenal.

Another device that has proven itself in the field of cleaning plastic surfaces is a steam cleaner. However, you need to be extremely careful here, since for some products its use is unacceptable: hot steam can negatively affect the connecting materials and damage the structure. Therefore, it is better to entrust the use of a steam cleaner for cleaning plastic to professionals - those who work at the Cleaner cleaning company! Leave experiments for later.

Return

How to clean plastic panels in the bathroom?

Forum / Finishing materials / What to clean plastic panels in the bathroom?

Ask your question on our forum without registering
and you will quickly receive an answer and advice from our specialists and forum visitors!
Why are we so sure of this? Because we pay them for it!

Find out details

Friends with a small child were visiting. He drew “naughty” drawings on the plastic panels with felt-tip pens.

Effective products for cleaning plastic panels without streaks

It was not possible to remove it immediately; the markers seemed to be firmly absorbed into the panels. How to bring out such art without damaging finishing material?

Markers don't always wash off easily. If the detergents have no effect at all, a felt-tip pen is probably alcohol-based and you can find out from your friends what they use to wash off the art. Try rinsing with alcohol. You will have to repeat several times and try not to smear. But it also depends on what dye. My markers sometimes left a mark, then gradually washed away.

Try it with a regular car wash. I use it for tiles and mirrors. Household products They leave stains and clean so-so. But it turned out to be just a song!)

If the felt-tip pen has become embedded in the panel, you will have to use alcohol-based products, or even better, alcohol itself; ordinary detergents will no longer help. I’ve never used a car washer, I won’t say anything about this option to mine.

I had to be a “victim” of the kids’ creativity on wallpaper, but not yet with a felt-tip pen on plastic panels. Most likely, scrubbing the art with alcohol, from alcohol directly to cologne, can help, but the proposal from Zimin regarding experiments with auto chemicals can also bring the desired result.

You can wash it off with alcohol or cologne. But the problem is that the marker ink is absorbed into the surface of the plastic. Therefore, you can try rubbing it with a match, only this is not washing off, but removing the top layer of plastic.

Unfortunately, it is not possible to completely remove the felt-tip pen from plastic panels, as it is easily absorbed. Try rubbing with alcohol, but a yellow mark will still remain. It can only be painted over.

Dear guest, stay!

Many people are already making money just by communicating on our forum!
For example, like this. Or like this.
You can start communicating on the forum now. Just log in via VKontakte or register, it will take one minute.

But if you are passing through us, you can still:

Today, wherever you look, you see plastic. This universal material used as wall and ceiling panels, floor tiles and, of course, window and door frames. Plastic is unpretentious, lasts a long time, and is inexpensive - why isn’t it an ideal material? But if you want it to not lose its original attractiveness, take the trouble to care for it properly. And here the question arises: “How is this “correct”?” To find out, you need to figure out what this material is? The impact of what he calmly endures, and from what he turns into God knows what.

Types of plastic panels

So, plastic is a type of polymer that is resistant to moisture, low temperatures, the action of aggressive substances (acids and alkalis). It is environmentally friendly and can withstand decent mechanical loads. Therefore, plastic is used in residential, children's, medical, office, etc. premises.

Despite all the advantages, the material is afraid of cleaning agents with abrasive particles and hot water.

Before you start washing plastic panels, you need to find out what type of panels are installed in your home. They come with a pattern and monochrome. The print is applied using hot printing. Then it is covered protective layer matte or glossy varnish.

The varnish gives the lamellas wear resistance and minimizes the formation of scratches. In addition, the panels do not age under the influence of ultraviolet radiation and have an antistatic effect. Plastic slats are divided into two types:

Laminated. They are covered with a shiny, smooth film, making the product attractive. These panels are easy to clean.
Not laminated. Have matte finish. Clean with a slightly damp cloth or dry method with a vacuum cleaner. They can be installed anywhere except the kitchen. Grease stains will remain on such panels, ingrained deeply into the body of the material. If the dirt is not removed immediately, the slats will remain stained forever.

Let's start washing plastic panels

Before you get started, do the following:

Put it on work clothes, rubber gloves and hat.
Remove everything unnecessary from the walls - paintings, sconces, lamps, etc. Make sure there is free access to the panels.
If there are decent seams between the slats filled with dirt, remove it with a rubber spatula.
Stock up on soft sponges (without an abrasive surface), lint-free cotton rags, fleece, and flannel.
Use water whose temperature does not exceed 40 degrees.
To prevent dirty stains from remaining on the panels after washing, wipe the surface with a damp cloth.
When choosing care products, avoid powdered mixtures. They will most likely leave micro-scratches on the surface of the slats, where dust will accumulate in the future. Liquid and gel detergents- This is what you need.
When purchasing a new product, test how your panels react to it. To do this, use the new product in an inconspicuous place and wait a few minutes. If the design has not been erased and the plastic has not darkened, feel free to use this product.
Using household chemicals to wash the panels, carefully remove it from the surface of the panels. Even small amounts of “residue” can cause an allergic reaction in people and animals.
To add shine to glossy panels after washing, be sure to wipe them dry and wipe them with a special polish.

Home remedies for cleaning panels

In addition to expensive factory-made drugs, you can use cheaper and, no less important, environmentally friendly home remedies.

How to wash plastic panels

They will turn out to be quite effective if you do not start the pollution process and regularly care for the plastic.

Soap solution

Take 30-40 grams of laundry soap, grated on a coarse grater (or dishwashing detergent), dilute it in half a liter of water.

Dampen a soft cloth in this solution and gently wipe the plastic panels.

Do not use to form a soap solution washing powders and bath care products.

Soda

If multi-colored stains have formed on your kitchen panels, make a paste of baking soda and water. Apply the mixture to the dirty area and leave for a couple of hours. Next, soak a soft sponge in warm water and wipe the treated area with it. Wet the sponge again and completely remove any remaining cleaning product.

Soda is an abrasive. Therefore, to avoid the formation of small scratches, apply the soda slurry very carefully, without rubbing it into the surface of the panels. Also carefully remove dried soda from the surface of the panels.

Vodka or table vinegar

These liquids will do an excellent job of removing dried traces of fat on plastic facades and wall (ceiling) panels. Just don’t forget to test vinegar or vodka on surfaces with bright patterns. And further. Don't forget - vodka is not alcohol.

Ammonia

Excellent for cleaning window sills, frames and glass. Copes perfectly with greasy deposits. Take 1 liter. water 1 tbsp. l. ammonia. Wipe the plastic surfaces with this solution, and then wipe them dry with a microfiber cloth.

Melamine sponge

These sponges are an ideal cleaning agent. They remove literally everything, while the surface remains as good as new. By the way, if you have heard that melamine sponge is a harmful thing, read the reasoned truth about it here... (link).

Melamine sponge has one drawback - it tears and crumbles. Therefore, do not use the entire surface - work with a small part or corner of it.

Cleaning the plastic on the ceiling

Actually, in essence, caring for ceiling plastic slats is not much different from caring for walls. But since working with your hands up is not so easy, use these recommendations:

vacuum the ceiling once a month;
Wash the panels in the kitchen with a hog bristle brush using a warm soapy solution;
To make the process faster, take a mop that rotates in all directions with a cloth cover;
To rid plastic ceiling slats from stains, wash them with alcohol-containing products.

How to clean plastic panels from tobacco smoke

After taking the drug, the lungs will process up to 80% of oxygen. There is also a blocking of pleasure receptors that are irritated by nicotine. You can easily quit smoking.

Reviews How to clean plastic panels from tobacco smoke

Olga Nikolaeva: yesterday - Both the smoker and those who decide to quit experience some symptoms that affect the quality of life. This feeling of fatigue, weakness, nervousness. Cough and shortness of breath are also a concern. To get rid of these symptoms, you must first smoke, since their cause is chronic intoxication of the body with nicotine combustion products from cigarettes. Nico Cleaner helps to quickly eliminate these unpleasant problems, which not only has a positive effect on life self-esteem, but also becomes a factor in the success of quitting smoking. Reviews How to clean plastic panels tobacco smoke:

Alina Emelianenko: 3 days ago - NicoCleaner - a lung cleaner from tobacco smoke helps take care of health and prevents development dangerous diseases caused by smoking. This reliable, proven assistant quickly eliminates unpleasant consequences bad habit, relieving fatigue, weakness, cough, shortness of breath and other symptoms. I have been smoking for 15 years. When I started coughing constantly in the morning and noticed dark sputum, I decided to try to quit.

It was hard, but a friend recommended NicoCleaner. The drug made the throwing process much easier. Lungs in as soon as possible cleaned up, arrhythmia and addiction to cigarettes disappeared:

NicoCleaner - a lung cleaner from tobacco smoke helps to take care of your health and prevents the development of dangerous diseases caused by smoking. This reliable and proven assistant quickly eliminates the unpleasant consequences of a bad habit, relieving fatigue, weakness, coughing, shortness of breath and other symptoms. How to clean plastic panels from tobacco smoke. In just one course of using Nico Cleaner spray, the surface of the lungs is cleared of tar, cough and shortness of breath disappear, and health returns to normal. In addition, the product promotes cellular regeneration.

How can I clean plastic panels?

How to prepare plastic for bleaching. Before washing off the yellowness, the surface plastic products prepare for the procedure. Then the door and side panels or window frames cleaned of soot and dirt, especially this applies. Digital panels. Warehouse in Moscow. Low prices. Direct deliveries. Wholesale from 10,000 rubles. Stretch ceiling for any wallet! Installment plan 10 months from AZIZA. We will make you an offer you cannot refuse. Products for exhibitions, offices made of plastic, plexiglass according to sketches and drawings.

I have been smoking for 15 years. When I started coughing constantly in the morning and noticed dark sputum, I decided to try to quit. It was hard, but a friend recommended NicoCleaner. The drug made the throwing process much easier. The lungs cleared out in the shortest possible time, arrhythmia and addiction to cigarettes disappeared.
Buy NicoCleaner in Severodvinsk
Harm of tobacco smoke for children
Interaction medicines with tobacco smoke components
Cleansing the lungs from tobacco smoke in the apartment
Buy NicoCleaner in Berdsk
Smokey out anti-smoking spray price

Plastic panels: care features

Today there are plastic panels, or plastic skins, for the kitchen. are very popular. They are also often used for bathrooms. This great option for those who want to quickly, beautifully and inexpensively update their interior. But every housewife, when choosing any pieces of furniture, interior details or finishing elements, asks the question: How to care for them. to preserve them for a long time appearance and functionality?

The best way to wash plastic panels in the bathroom and kitchen

Plastic panels can be laminated or non-laminated. As a rule, laminated panels are used for kitchens and bathrooms. One of the main reasons for the popularity of this finishing material is that it is easy to care for. Plastic panels are antistatic, so dust practically does not settle on them. They are washed with warm water with the addition of detergents. After wet cleaning It is recommended to wipe them dry with a dry cloth to avoid streaks and enhance shine.

Typically, plastic panels in the kitchen are susceptible to contamination with grease that splashes during cooking; areas near the stove are especially affected.

The following will help remove grease from plastic panels in the kitchen and bathroom:

1. Dishwashing detergent: apply it to a sponge, wipe the panel with it and leave for 5 minutes. After this, wipe the surface again with little effort;

The best way to wash plastic panels: a review of chemicals and folk remedies

Windshield wipers: as a rule, these products contain alcohol, which perfectly corrodes grease;

3. Melamine sponge: simply rub the dirty area;

4. Special products for cleaning the kitchen, including the time-tested “Anti-grease”.

When caring for plastic panels, do not use abrasive detergents, metal scrapers or brushes. They can easily scratch the surface, and later dust and dirt will accumulate in the resulting microcracks even more than before.

The problem with plastic bathroom panels is soap stains and the appearance of black mold. You can fight them with special means for the care of bathrooms and showers. Besides soap stains on the panels are washed off well using a solution from ordinary water And lemon juice, where at 200 gr. water is 20 grams. juice or citric acid.

Ink from a ballpoint pen can be removed using a regular match. To do this, you just need to rub the area with the head of a match dipped in water. After the stain disappears, the previously contaminated surface should simply be washed with soapy water.

Juice from berries and greenery easily clean the panels using liquid gels with a whitening effect, such as “Dosya”, this gives 100% results for white surfaces, while with colored, bright panels you need to be careful not to discolor them. It’s better to try a drop of the product somewhere in an inconspicuous place; if the panel does not change color, you can start removing stains. After such treatment, the surface must be thoroughly rinsed with water and wiped dry.

A plastic that is often used to make decorative panels, refers to an inexpensive and wear-resistant finishing material. One of its main advantages is its unpretentiousness in terms of care.

However, like other surfaces, plastic panels need to be kept clean, especially if they are located in the bathroom. If this is not done, then over time they will develop a coating of dirt and dust, which will require a lot of effort to clean. To maintain the surface in good condition It is enough to wash it at least once a month.

Processing of plastic panels

When choosing how to clean plastic panels in the bathroom, you need to take into account some of the features of this finishing material and environmental conditions. There won't be much result if you just wash them. clean water, therefore, during the cleaning process you should adhere to these rules.

To avoid damaging the surface, it is better to avoid products containing abrasives. Their use leads to the formation of scratches and mold, which is very difficult to combat. It's better to choose industrial compounds and self-prepared mixtures made from mild and effective reagents.

Hard brushes will ruin the aesthetic appearance and scratch the surface. To wash plastic panels in the bathroom, it is better to use a sponge or soft rag.

To prevent streaks from appearing on the material immediately after cleaning, it must be wiped with a damp cloth. clean water and then remove excess moisture.

For treating plastic surfaces in the bathroom, it is better to use available and proven products. folk remedies, and not household chemicals that may contain unsafe additives.

Effective homemade compositions for cleaning panels

To treat and update the appearance of plastic surfaces, you can use safe mixtures prepared by yourself.

The following solution copes well even with old stains. Add 1 tsp to a glass of warm water. baking soda and 9% vinegar, a couple of drops of your favorite essential oil. The mixture mixes well and is thoroughly wiped with a sponge soaked in it. problem areas, then everything is washed off.

Panels and other elements can be cleaned with a special composition. To prepare it, take half a glass of Castile soap, 1 tsp. lemon juice, also 1 tbsp. l. starch is better than potato starch with the addition of 0.5 cups of slightly warmed water. All ingredients are mixed and the composition is applied to the surface to be treated. After 5-10 minutes, the plastic is washed and wiped.

A mixture of 0.5 cups of well-heated water, 1 tbsp. l. soap shavings and 1 tsp. citric acid. A thoroughly mixed solution is applied to the surface of the panels and washed off after 10 minutes.

To clean shiny areas, a solution prepared from half a glass of water, 1 tsp is suitable. baking soda, 1 tsp. starch.

If your bathroom is covered with colored panels, then it is better to first test any product used on an inconspicuous area; if the color does not change, feel free to proceed to treating the entire surface.

The choice of “clothing” for walls and ceilings is always difficult. Especially if it concerns the kitchen, bathroom or toilet. Wallpaper or tiles? Or maybe just paint? Yes, but they also have certain disadvantages. Such an original approach as plastic panels can save the situation.

How to wash plastic panels and what does care depend on?

Firstly, it is worth clarifying that plastic panels can be laminated or non-laminated. How to distinguish? Products of the first type are covered with a smooth and shiny film. It is this that prevents the panels from scratching and breaking so easily. Therefore, it will be easier to wash them, how to clean plastic panels without laminated coating. To do this, you can use a soft sponge or rag with gel detergents or just a soap solution. Despite the resistance to damage, it is better not to clean the surface with grainy powders or products containing acid or solvent, as well as metal sponges and coarse bristles.

If the contamination is serious, you can rub it more vigorously - the appearance of the plastic will not be affected. To get rid of greasy stains, it is good to wipe with an ammonia solution, but only in the area of contamination.

Despite all the moisture resistance, it is unacceptable to leave spilled puddles for a long time. Therefore, immediately after wet cleaning, you need to wipe the surface with a dry cloth.

To improve attractiveness and restore shine, it is worth using special products, for example, plastic polishes. Ease of use and high quality final result– wipe with a cloth and you’re done! Moreover, most of them are safe for contact with food products.

The second type? Dry cleaning is best for them. This can be wiping with a soft cloth or cleaning with a vacuum cleaner. Grease stains or other heavy dirt will be difficult to wash off. Therefore, this type of panel is not recommended for use in the kitchen. In this case, it is best to remove the contamination as soon as it appears, otherwise it may become absorbed over time, and then the plastic will hardly be helped in any way.

That's all the secrets. If you know about plastic panels, cleaning will not seem like a terrible beast and all the problems about sloppiness in the kitchen or children's pranks with paints will evaporate.

Plastic ceilings are very popular due to their practicality. They are inexpensive, easy to install, and impress the eye with brilliance and cleanliness. But over time, the pristine beauty disappears due to the accumulation of cobwebs, dust, and stains. All this spoils the picture and is no longer pleasing to the eye. But the ceiling is the face of the room, so it needs to be cleaned regularly. Then the question arises: how to wash a ceiling made of plastic panels, what methods exist to remove contaminants.

To cope with this task, you need to know the reasons for the appearance of unwanted formations and methods of getting rid of them.

About the causes of pollution

The factors that contribute to the appearance of dirt on plastic are varied. Here are some of them:

dust, soot and soot, which are most often the cause of pollution in the kitchen
Various fats and oils are the culprits of sticky plaques that form due to evaporation during cooking. Due to their sticky consistency, they become covered with dust and are difficult to clean.
condensation that forms in the bathroom and kitchen due to hot water vapor. This is caused by the content of alkaline, salt and lime impurities in it, which, after evaporation of the liquid, form an insoluble coating and cause stains.
cigarette smoke covering the surface of the ceiling with a gray coating
leaking roof. Due to precipitation and dampness, rusty and dirty stains form on the ceiling surface
Faucets and pipes due to malfunctions cause rust. It should be taken into account that water can seep through hollow concrete floors, and the stain appears in unexpected places located far from leaking objects
An equally common reason is repairs, after which traces of wallpaper glue, putty, grout and paint remain
mosquitoes, midges, flies, moths that penetrate the house and leave dark spots

Preventive actions

Elimination of the listed problem situations involves the following actions:

installation of forced hoods, which prevents the formation of condensation
Minimizing fat and oil deposits using a range hood
timely repair of roofs, pipes, taps
regular wet cleaning of the premises to prevent dust from settling
Mosquito nets on windows to prevent insects from entering

Necessary tools and cleaning products for cleaning the ceiling

To wash yourself plastic ceiling, first of all you need to select the simplest tools:

water container, taking into account the addition of detergents to it
a soft cloth, several rags (rags are better)
latex gloves
foam sponge
a special mop with a soft, replaceable cloth or microfiber tip
brush with natural bristles (for cleaning the ceiling in the kitchen)

You may also need a vacuum cleaner to remove dust first. This will prevent the formation of streaks.

About purchased detergents

You can opt for a professional household chemicals. Funds in this category are represented quite widely.

A highly effective product - L.O.C. cleaner. Amway brands. It is washable various materials. The product is environmentally friendly. It does not need to be washed off with water.

Mr. liquids for cleaning walls and floors are very popular. Proper and Mr. Muscle. These are foaming products with a pleasant, quickly dissipating odor. The cleaning process is speeded up by the fact that the use of preparations does not require additional rinsing with water after finishing work.

Important! Before use, be sure to read the instructions containing instructions on correct use substances.

Homemade cleaning solutions

Products prepared at home are not inferior to factory-made drugs. Here are a few recipes for products that cope well with stains on plastic surfaces:

A simple soap solution. Regular dish soap is added to the water. You can use grated soap. Fill it with warm water and wait 30 minutes. to soften, then foam the solution.
Whitening agent. Add 2 tbsp to 5 liters of water. available bleach. This is a good way to wash yellowed plastic panels to give them a fresh look.
Ammonia copes well with the problem of fatty plaques and plaque on plastic. Dilute 1 tablespoon of alcohol in 1 liter of water.
Baking soda with water is an excellent remedy for all kinds of stains. To do this, prepare a liquid paste from these components and apply it for 2-3 hours. Then wipe with a soft sponge moistened with warm water.

How can plastic be damaged?

When using all kinds of means and tools, you need to know that some of them can damage the surface of the panels. To prevent this from happening, you must remember that:

You should not use abrasive products to wash the plastic ceiling, because they can scratch it and ruin the gloss
brushes must be soft, the use of sharp objects is unacceptable
When using a mop for convenience, you should work carefully so as not to make dents on the plastic panel
acetone, vinegar, vodka, as well as laundry soap containing a high percentage of alkali can damage the integrity of the material
When using baking soda, do not scrub the stain with force.
It is not recommended to use washing powders for preparing cleaning solutions

The main rule in using all means is the ability to foresee possible damage plastic. Therefore, before use, it is advisable to conduct an interaction test in an inconspicuous place.

Where to start and how to wash

All advice on this issue is quite conditional and cannot be an accurate guide to action. However, there are requirements that must be met:

Before starting work, it is necessary to clear the room of unnecessary objects;
Use a vacuum cleaner to remove dust from the ceiling;
Then you should rinse the ceiling with clean warm water. After this, you can apply any version of the solution described above and leave it on the surface for some time (3-5 minutes). Gently wash the ceiling with a sponge or rag;
Before drying, you need to wash it again with water;
Wipe the ceiling with a soft flannel or rag, changing rags often to avoid streaks.

IN living rooms The plastic ceiling is easy to clean if you clean it regularly with a vacuum cleaner.

How to get a clean kitchen

It is more difficult to wash ceiling panels in the kitchen. Adhering fatty plaques, soot, and stains from fumes cause many problems. Therefore, many are interested in the question of how to wash the plastic ceiling in the kitchen.

An indispensable remedy for greasy deposits is a soap solution followed by treatment with an alcohol-based product.

The above-mentioned soda paste recipes and a solution with ammonia work well in removing greasy stains.

Yellowed plastic is treated with a product containing bleach or ammonia.

Universal assistant in the kitchen - melamine sponge. With its help you can remove contaminants of any origin. To do this, just moisten it with water and wipe the surface.

After using detergents, it is necessary to rinse the plastic with water, because chemical substances may contain allergens.

Given that regular care behind the plastic ones ceiling panels Contaminants are easily removed. But if the dirt is old, you will have to process it 2-3 times.

Cleaning kitchen ceilings differs from cleaning them in residential areas only by requiring more effort and time.

Everyone decides on their own how to wash plastic ceilings at home. The main thing is that this process does not cause negative emotions, does not turn into torture, but gives pleasure from the result obtained.

To ensure that the ceiling is always pleasing to the eye, it is necessary to lightly treat its surface from time to time. In this case, you won’t have to spend a lot of effort fighting stubborn, old stains.

Liked? Share on social media networks!

remontcap.ru

How and with what to wash a plastic ceiling?

After the plastic ceiling is installed, the eye never tires of rejoicing at the wonderful transformation of the room and the radiance emanating from above.

But, despite the seeming inaccessibility of coverage for various sources dirt, over time it becomes noticeable that its appearance is far from what it was immediately after installation. Due to the accumulation of dust, shine disappears, various stains spoil the overall picture. The surface needs cleaning. Before you wash your plastic ceiling, you need to know the causes of contamination and how to eliminate them.

You need to know this in order to:

prevent this from happening in the future;
choose the right way removing dirt;
pick up suitable material for cleaning;
purchase cleaning products suitable for the event.

Causes of pollution

Plastic covering suspended ceiling can become dirty for many reasons, sometimes beyond the control of the apartment owner.

So, the main causes of pollution may be:

Dust is an eternal inhabitant of any room. Gradually settling on the coating, the dust covers it with a thick layer, which hardens over time. This gray layer will do nothing to brighten up the room.
Leaking roof or wall. Water, entering the concrete through small cracks, moves downwards, along the way absorbing rust, dirt and other components of the surface of the roof and wall. The result is dirty spots appearing along the edges and in the middle of the ceiling.
Fat deposits. This problem is typical in areas where food is prepared and eaten. As fats and oils evaporate, they reach the surface, where they cool and firmly adhere to the surface. In addition to the fact that such fumes create stains, they also collect a lot of dust, creating a surface with gray, unpleasant-looking stains.
Tobacco smoke. Rising upward, cigarette smoke covers the ceiling with a thick, evenly distributed brown coating having an unpleasant, pungent odor.
Leaking pipes. Pipes located in walls and ceilings can leak over time. In such places the metal is rusty. Water flowing out of such a pipe leaves red streaks on the plastic.
Condensation stains. Such phenomena occur in rooms where there are sources of steam - in bathrooms and kitchens. The water contains chlorine and limescale. When the condensate from the steam evaporates, its contents remain on the surface.
Consequences of repair. During repairs, the surface may be splashed with paint, glue or cement mortar.
Insects. Flies can cause a lot of black dots to appear on the ceiling. Over time, they begin to become very noticeable.

Elimination of causes

As they say, it’s clean not where they clean, but where they don’t litter. This statement fully applies to the ceiling. To get rid of the problem of stains on the coating, it is necessary to eliminate the causes of their appearance.

Here's what you need for this:

Equip windows with mosquito nets. This will prevent flies from entering the apartment and will significantly reduce the entry of street dust into the premises.
Install forced exhaust in rooms with high humidity. The steam, without reaching the surface, will go into ventilation shafts.
Equip the stove on which food is prepared with a powerful hood that will collect fatty fumes on its filters. They are much easier to clean than the ceiling.
No smoking indoors. If you do this, then near the switched on hood.
Deal with leaking roof and pipes. This will not only prevent further stains from appearing, but will also rid the apartment of unnecessary dampness.

Basic washing rules

The ceiling, unlike the floor, gets dirty much more slowly. But when its surface, instead of pleasing the eye, evokes negative feelings, it’s time to wash it.

When cleaning the ceiling, you need to follow some rules that will not only allow you to achieve a high-quality result, but also prevent damage to the delicate plastic surface.

These are the rules:

Do not use knives, brushes or abrasives to clean hard deposits. This may scratch the surface.
Acetone-based cleaners can melt the plastic or ruin the surface pattern.
Detergents containing abrasives are contraindicated for plastic surfaces. Due to their impact, the applied gloss will darken and lose its appearance.
Accuracy in work. The surface of the plastic is quite soft and you can leave a dent on it with a hard object.
A stable platform to work on. You need to wash the ceiling on a stable, wide surface or on a reliable stepladder.

What and how should I wash the ceiling?

Taking into account the specifics of the surface being treated, to clean the ceiling made of PVC panels, you can use materials and devices that are used for washing windows.

Tools and materials

In order to thoroughly clean a dirty ceiling you will need:

mop for cleaning windows;
natural fabric, which absorbs water well;
foam;
water container (bucket or basin);
alcohol-based detergent (after their use, a characteristic shine appears on the glossy surface);
ladder.

Having prepared such a set, you can start washing the ceiling.

Sequence of work

Usually everyone is interested in how to clean the ceiling and in what order it should be done. Work on cleaning the surface from contamination should be carried out in the following sequence:

Clean the surface from dust with a vacuum cleaner. Dust particles mixed with the solution can, like an abrasive, scratch the surface.
Wet the surface with warm soapy water to loosen the dirt.
Wipe the entire surface of the ceiling with a cloth soaked in the solution, constantly refreshing it.
Without allowing the soap solution to dry, rinse the surface with clean water.
Collect moisture with foam rubber in hard-to-reach places (joints between panels and along the baseboard).
Wipe the surface dry with a dry soft cloth.

If the coating has become heavily soiled, leaving deposits on its surface facing the ceiling, then this problem can be solved by dismantling the entire structure.

In this case:

the structure is disassembled;
each panel is individually washed and wiped dry;
the frame and floor slab are cleaned;
the ceiling is installed in its place.

potolokvdoma.ru

How to care for a plastic ceiling in the kitchen

The ceiling in the kitchen should be easy to clean and poorly absorb foreign substances. Plastic ceilings fully meet these requirements. That is why the plastic ceiling is The best decision for kitchen. Of course, such a ceiling also gets dirty and turns yellow after a while. However, fixing the situation is not so difficult.

How to keep a plastic ceiling in perfect condition

Over time, almost everything in the kitchen turns yellow, starting with ceramic tiles(it’s just not very noticeable), curtains, wallpaper and, of course, the ceiling.

However, if you take care of the ceiling (or any other surface in the kitchen) from time to time, wash it and clean it, then problems with yellowness will not arise at all. A plastic ceiling will always look new. It is not difficult to wash it. To do this, you need to wipe it with the addition of some safe detergent.

How often do you need to wash your plastic ceiling to keep it in good condition? It is advisable to carry out this procedure twice a month. This is not at all difficult, because if the ceiling is washed regularly, then it simply does not have time to get very dirty, so it is enough to just wipe it lightly.

And to make the task easier, you can take a good mop and use it. It is not at all necessary to climb to the ceiling, climb onto the table and wield a rag there. Very comfortably.

Why is a plastic ceiling easy to clean?

However, if the kitchen ceiling is already very yellowed, washing it is also not very difficult. It’s just that in this case you will have to spend much more effort and time on cleaning. One of the main advantages of plastic ceilings is that they do not absorb foreign substances and yellowness does not eat into the material.

In other words, the yellow coating can simply be wiped off with a rag, and underneath it will be the same white and clean ceiling as on the first day of its installation.

What products to use to care for plastic ceilings

You can wash the panel ceiling by different means. One of the best, which is often recommended on the Internet, is a soap solution. This solution is not difficult to make yourself. You just need to add more soap suds to hot water.

Of course, it will be difficult to wash the ceiling with a rag. Better take a mop. Mop and soap solution with hot water You can deal with almost any dirt that may appear on the ceiling over time. True, you will have to wash the ceiling several times, replacing the water with clean water each time. This must be done so that the solution is completely removed from the ceiling at the end of cleaning.

As for soap varieties, one of the best options– laundry soap. Just don’t buy new laundry soap, white. It is advisable to find a classic example that has a characteristic yellow. This soap is natural, safe and very effective for cleaning plastic ceilings.

In addition to soap solution, you can use dishwashing detergent. Another popular remedy is ammonia. Dish soap is used in the same way as soap for soapy water. That is, a certain amount of the product is poured into hot water and stirred well until foam appears. Ammonia should be used in much the same way. Of course, alcohol will not foam, but this is not required, because it can cope with even a strong coating without it.

How to reduce the load on a plastic ceiling

To prevent the plastic ceiling from becoming too dirty, you need to install a hood in the kitchen or open a window when cooking. Of course, a hood is not always available and it is possible to install it. In this case, as already mentioned, it is recommended to wet clean the plastic ceiling twice a month. This will not take much effort, because in two weeks the ceiling will not have time to get very dirty and it will be enough to simply wipe it with warm water, even without special equipment.

vindeks.ru

How to wash a plastic ceiling with your own hands - important tips

How to wash a plastic ceiling

Why do spots appear?
How to wash a plastic ceiling?

Facade plastic
Glossy surfaces

Methods
Useful tips

The ceiling in any residential building or apartment is one of the main elements of the interior. Therefore, it should look appropriate: be clean and beautiful. No matter how much you would like to protect the surface from contamination, this happens very rarely, so the thought of how to wash a plastic ceiling, at least once, still worried every housewife. Still, from time to time various stains appear on it that need to be dealt with.

Why do spots appear?

Stains on the ceiling

Causes of stains on the ceiling:

if the floor you live on is the last, then suddenly appearing stains on the ceiling may be a consequence of a roof leak. If the house is old or some errors were made during the installation of the roof. It may slowly seep through the seams of the floor slabs. dirty water, and leave a mark on your ceiling;
your neighbors with top floor Leaking pipes or improper handling of taps can also cause stains. It is almost imperceptible, and you will not be able to understand that it is they who are gradually undermining you;
a leaky riser from which water gradually flows into the cavity concrete floors, and over time, having found a weak spot, it begins to leak. This weak spot may be the seam above your apartment. You yourself will not be able to detect where exactly the riser is leaking if it is actually the cause of the stains. A specialist is needed here;
if during repair work you used low-quality Construction Materials. In particular, putty for the ceiling, as a result, stains from this material may appear over time. Or you simply violated the rules of repair technology, if the material you purchased was of high quality. In this case, it will be necessary to redo part of the structure again, because it is impossible to wash off this type of stain;
If you smoke, or someone smokes in the house, then don’t be surprised later where the stains on the surface came from. The soot from tobacco smoke leaves its mark;
if there is no hood in the kitchen, then soot from grease also settles on the surface of the ceiling, which is why they appear later greasy spots;
in the bathroom on the ceiling can often gather white coating, these are impurities from water that remain after evaporation droplets dry;
If you find small specks of unknown origin, it may be splashes from some product. For example, a tomato, when it splashes juice, but you can’t see it right away;
and finally, the most banal reason is traces of flies.

Also read: Plastic ceilings in the kitchen.

How to wash a plastic ceiling?

In order to choose the right product that will help you both wash the plastic ceiling and not harm it, you need to take into account the type of its surface. Because different surfaces wash differently.

Facade plastic

Such surfaces are easy to clean. All cleaning and detergents that do not contain chlorine or abrasives can be used for them. Plastic itself cannot absorb any substances, so stains are washed off easily.

Glossy surfaces

Cleaning and detergents

On such surfaces, traces of contamination are visible much more clearly than on matte surfaces. But unlike matte ones, they are easier to clean. In order to wash it, you can use any detergent, the main thing is that it is not abrasive or does not contain the same abrasive elements. This type of cleaning may leave marks and scratches on the surface of glossy panels, and it may become dull. You can use any shower gel, shampoo, liquid soap, special liquids for washing and cleaning windows, etc.

Methods

Today, there are specially created services that offer their services for washing ceilings and cleaning the house. You can also use their suggestions, although it is quite possible to do this procedure yourself:

If the ceiling is covered with paint water based(water-based), it is very important to know what moisture resistance it has. You can remove a stain from such a ceiling with a solution in which you need to dilute vitriol with water in the ratio: 200 g per 5 liters of water. If the stain doesn't budge, try increasing the concentration much further.
If the ceiling is suspended, then you can simply vacuum it periodically. Then the need for washing disappears automatically. You can sometimes wash it with water soapy water with a cloth.
If the ceiling is glossy, you need to wash it with gentle detergents so as not to leave scratches, which will later become very visible.
If the ceiling is tiled. You can wash it with detergent and a hard sponge. To do this faster and better, first wet it and let it soak a little.

Ceiling cleaning

The effect depends on how to wash the plastic ceiling. All washing procedures must be performed carefully and slowly. Choose rags from soft flannel. Select detergents only those that do not conflict with their use on a particular surface.

Important: The temperature of the soap solution for soaking or washing the ceiling should be approximately 40 degrees.

Don't skimp on their prices. A polished surface is much easier to clean and retains dust. Even if it has a slightly glossy surface, treat it with alcohol-containing products. This will prevent the formation of streaks. Wash ceilings as they become dirty and do not allow ordinary stains to turn into old stains. They are more difficult to deal with, since they can be eaten away, and to remove them you will need to make a lot of effort or harsh detergents, which can damage the plastic.

Video about proper ceiling cleaning

To date plastic panels, or plastic skins for the kitchen, are very popular. They are also often used and for bathrooms. This is a great option for those who want to quickly, beautifully and inexpensively update their interior. But every housewife, choosing any pieces of furniture, interior details or finishing elements, asks the question: How to take care of them? care to preserve their appearance and functionality for a long time?

The best way to wash plastic panels in the bathroom and kitchen

Plastic panels can be laminated or non-laminated. As a rule, laminated panels are used for kitchens and bathrooms. One of the main reasons for the popularity of this finishing material is that it is easy to care for. Plastic panels are antistatic, so dust practically does not settle on them. They are washed with warm water with the addition of detergents. After wet cleaning, it is recommended to wipe them dry with a dry cloth to avoid streaks and increase shine.

Typically, plastic panels in the kitchen are susceptible to contamination with grease that splashes during cooking; areas near the stove are especially affected.

The following will help remove grease from plastic panels in the kitchen and bathroom:

1. Dishwashing detergent: apply it to a sponge, wipe the panel with it and leave for 5 minutes. After this, wipe the surface again with little effort;

2. Windshield wipers: as a rule, these products contain alcohol, which perfectly corrodes grease;

3. Melamine sponge: simply rub the dirty area;

4. Special products for cleaning the kitchen, including the time-tested “Anti-grease”.

When caring for plastic panels can not use abrasive detergents, metal scrapers and brushes. They can easily scratch the surface, and later dust and dirt will accumulate in the resulting microcracks even more than before.

The problem with plastic bathroom panels is soap stains and the appearance of black mold. They can be combated with the help of special care products for bathrooms and showers. Besides soap stains on the panels are washed off well using a solution of plain water and lemon juice, where 200 g. water is 20 grams. juice or citric acid.