home · Installation · Soft roofing shinglas installation. Installation of soft tiles Shinglas (Shinglas) - a special installation technology and secrets for roof care. Roof ventilation TechnoNIKOL

Soft roofing shinglas installation. Installation of soft tiles Shinglas (Shinglas) - a special installation technology and secrets for roof care. Roof ventilation TechnoNIKOL

  • Arrangement of valley, ribs, ridge, domed roofs, junctions and penetrations

Roofing system covered with bitumen shingles Shinglas should consist of a continuous vapor barrier on the room side, thermal insulation of the required thickness, windproof film. The under-roof space must be ventilated. Without ventilation, moist fumes will accumulate in and above the insulation layer.

Color code on packages flexible tiles check before installation, it must be the same. With the same code, there may be a slight discrepancy in shades. To make it invisible, material from several different packages is mixed. It is recommended to lay it in diagonal stripes.

If the air temperature is below +5°C, laying the material is possible, but with some restrictions. The packages are kept in a warm room. They are lifted onto the roof in several pieces just before installation. It is recommended to preheat the adhesive strips. A hair dryer is used for this.

Shingles are trimmed on a rigid backing (sheet of plywood, board). Cutting should not be performed on already laid bitumen shingles (there is a risk of damage to them).

Packages with material are stored away from heat sources and not in direct sunlight. Heat is avoided so that the adhesive strips do not stick to the siliconized film (it should be easy to remove).

When storing packages on pallets, they are not stacked (each pallet is placed separately).

To ensure that the sheets of material are well separated from each other, each package is slightly bent and shaken before opening.

It is not recommended to walk on an already installed coating if installation is carried out in sunny or humid, hot or cold weather(marks or stains may remain). Westmet engineers recommend leaving manholes for access to the desired area on the roof.

Materials

Shinglas bituminous shingles. Used as a base coat. There are more than 70 models in the catalog. Install according to the instructions below.

. They are used for additional waterproofing and leveling of continuous flooring, increasing the service life of the roofing system. The line includes:

  • self-adhesive underlay carpets of the ANDEREP ULTRA series. Made from polyester, bitumen, front surface - with protective layer from fine-grained mineral powder. Sprinkling increases the strength of the underlay carpet. The main layer is SBS-modified bitumen, which impregnates the polyester base (used as a reinforcing layer for greater strength). The inner surface is adhesive, with a siliconized film, which is removed before installation;
  • carpets with mechanical fastening. Universal carpet - ANDEREP PROF. Lightweight, the base is made of polyester, the main layer is bitumen impregnated, the front and inner surfaces are made of polypropylene, durable, non-slip. Can serve as a temporary roof for up to 6 months. ANDEREP PROF PLUS: the bitumen-impregnated polyester base is protected by a layer of Spunbond (non-woven polypropylene) on the outside and inside, with an additional self-adhesive edge (covered with film before installation). ANDEREP GL, GL PLUS: fiberglass base impregnated with SBS-modified bitumen. The surface is protected by a layer of fine-grained coating. On the surface there are thermoactive strips that stick together during operation, increasing the reliability of waterproofing. In the GL PLUS version, the edges are additionally protected by an adhesive layer.

When laying carpets, bitumen mastic is not used.

Valley carpet. Used in valleys and junction areas. Supplied in rolls. The base is made of polyester, reinforced with a layer of SBS-modified bitumen. The outer surface is a layer of colored basalt granules. The valley carpet is matched to the color of the roof and is used in areas where the risk of leaks is increased.

Planks: junctions, end, cornice, pediment. Used as additional elements. The base is galvanized steel. Coating - polyester or granulate (protects against corrosion). When installing the roof, planks of the same color as the roofing are used.

Fasteners TECHNONICOL supplies bitumen shingles roofing nails 45x3.5 or 30x3.5. Made of galvanized steel, they have a ring knurl (they are held in the flooring five times more reliably). The diameter of the cap is increased. After installation, the fastener caps are hidden by the tabs of the overlying shingles.

Mastic. Used for gluing bituminous shingles to the underlayment, at junction areas, and for laying valley carpets. TECHNONICOL No. 23 FIXER contains bitumen, polymers, solvents, fillers. Is cold mastic(does not require heating before use).

. To organize the removal of wet fumes from the under-roof space, aeroelements, aerators, TECHNONICOL valves are used, and a sufficient number of vents are provided.

Auxiliary materials can be replaced with products from third-party manufacturers, provided they have similar characteristics.

Terminology

Consumption rates for flexible roofing

The useful coverage area is indicated on each package of material. For most cutting forms and collections it is 3 m 2 /pack. Exceptions:

Mastic consumption

Varies for different nodes and sections:

  • joints of lining carpet fabrics - 100 g/linear. m (mastic is used if the lining carpet does not have self-adhesive strips along the edges);
  • valley carpet- 400 g/linear. m (the edges are glued around the perimeter);
  • abutments - 750 g/linear. m (the edges are glued along the junction).

Observing the consumption rate, ensure that the mastic is applied thin layer(up to 1 mm). It is impossible to increase the thickness of the layer so that swelling does not form in areas of overlap.

We carry out installation soft roof brand "Shinglas", instructions from the manufacturer TECHNONICOL. This roofing covering is one of the modern bituminous materials, characterized by increased performance properties. The main advantages of the coating: attractiveness, good sound insulation, thermal insulation characteristics, tightness, resistance to impacts natural environment, long operational period. SHINGLAS soft roofing is a fairly lightweight building material; its installation does not require the use of specialized equipment, so you can do the roofing work yourself.

In this article

Structure, material characteristics

Soft roofing "Shinglas" is made in the form of shingles, which have a figured edge in the form of petals, forming a coating texture that resembles tiles. The basis for the production of roofing covering is durable fiberglass canvas. The material is not afraid of moisture and temperature changes. The reinforcing base is covered on both sides with special modified bitumen, which low temperatures retains its elasticity. As a result, the roofing material does not crack during sudden temperature changes, at sufficiently low temperatures.

Structure of flexible tiles "Shinglas"

  • The top layer is basalt powder.
  • Next is improved bitumen.
  • The base is made of fiberglass.
  • Improved bitumen.
  • The bottom layer consists of a self-adhesive frost-resistant bitumen-polymer mass.
  • The protective layer is made of siliconized film, which is easily removed.

The top layer of material is basalt chips with a special binding component. It protects bitumen from external influences of the natural environment, gives the surface roofing material aesthetic appearance. Pigments used in production process for soft tiles "Shinglas", different increased stability to the ultraviolet rays of the sun.

The bottom of the shingles is processed special glue, which allows you to easily install sheet material on a prepared roof. A special siliconized film applied to the adhesive layer of the coating protects individual shingles from contact during transportation and storage of roofing material. The film is removed immediately before laying the shingles on the roof. The adhesive composition used for Shinglas roofing retains its original performance characteristics for a sufficiently long period of time, it provides the coating with excellent sealing and does not lose elasticity when negative temperatures.

How to properly lay soft roofing "Shinglas"?

First you need to accurately calculate required amount roofing material for the roof. To do this, you need to calculate its total area, consisting of the sum of the areas of all individual roof shapes, which can have the shape of triangles, rectangles, trapezoids, etc. geometric shapes. Consumables will be needed not only for covering outer surface roofs, but also for installing a lining layer and arranging adjacent structures. When performing calculations, it is imperative to determine the length of the ridge, cornices, valleys, ends, elements adjacent to attics, pipes, and other structures.

To install a roof with flexible tiles, you will also need the following materials:

  • metal components of the roofing structure - eaves, windshields, adjacent strips with anti-corrosion coating;
  • bitumen-polymer mastic, which is used for gluing bitumen-based materials to various surfaces;
  • self-adhesive lining materials made on a polyester basis, treated with outside protective decorative powder;
  • baseless linings reinforced on the outside with a protective film;
  • galvanized roofing nails;
  • lining carpets made on the basis of polyesters with non-slip coating made of polypropylene;
  • underlay carpet, treated on both sides with mineral coating;
  • Components ventilation system;
  • valley carpet made on a polyester base, the bitumen layer is treated with basalt topping, used for waterproofing on complex roofing areas and assemblies.

The consumption of tiles will depend on the type of cutting of the petals. The manufacturer indicated it on the packaging of the material usable area taking into account overlaps. Depending on the shape of the shingles, soft roof waste can be up to 15%, but not less than 5%.

You need to understand! To prevent swelling of the carpet and smudges from forming, it is forbidden to add solvents to the mastic, and the material itself must be applied in a layer of up to 1 mm.

Preparing the base

SHINGLAS roof installation technology assumes the presence continuous sheathing. The rafter system is decked with high-quality edged boards, plywood, other sheet material. To prevent joints of the four corners, the installation of flooring sheets is carried out “in a staggered manner.” For their fastening, self-tapping screws and rough nails are used. The plank flooring is made with a five-millimeter space between individual planks. If the arrangement of the sheathing is carried out in winter period, a five-millimeter gap is also made, necessary for thermal expansion of structural elements in summer.

Important! If the edged board used for arranging a solid type sheathing has not been calibrated, the material must be sorted by thickness so that subsequent installation changes in the size of the boards will be smooth. The difference between nearby elements should not be more than two millimeters.

When installing decking from high-quality edged boards, you need to look at the rings, the convex side of which should be directed upward. The lumber must be well dried before use, then its deformation is unlikely. If you had to use still wet boards, then their edges must be secured with at least two self-tapping screws. And in order for the structure to serve for the longest possible period of time, it wooden elements treated with fire-resistant, bioprotective agents.

Roof ventilation

To function effectively, a roofing structure with a bitumen coating must have good ventilation over its entire area. Ventilation system for soft roof is arranged in such a way that air does not stagnate in any area of ​​the roof space. Otherwise, the accumulation of moisture in the “dead areas” will contribute to the rotting of wooden structural elements, and it will also be absorbed by the insulating material.

The space between waterproofing layer and lathing. To do this, special openings are installed at the eaves, which after installing the roof are covered with soffits, and exhaust openings at the ridge. To create good draft, you need to provide a pressure difference, so the hood holes are made 15 percent larger than the ventilation holes. The parameters of the ventilation system duct will depend on the slope roof slopes. The lower the roof slope, the wider the ventilation ducts become.

  • When installing a soft roof, it is recommended to use the material from one batch so that during the process installation work avoid sharp color differences within the roof slope. When using asphalt shingles with the same color code from different batches, shingles from different packages must be mixed together immediately before installation. Then the color change will not be noticeable.

Important tip! In order for the shingles to be freely separated from each other, the packaging with the roofing material must first be bent, then shaken, and only then opened.

  • When laying soft roofing material in cold period year when outside temperature air temperature is no more than +5°C, packages with material should be stored in a warm room. Before laying it on the roof, the adhesive layer of shingles is heated using a hair dryer.
  • Often when laying soft roofing, excess material has to be cut off. For this it is recommended to use cutting tools with a well-sharpened blade, wooden planks on which the shingles will be cut.

Shingles should be stored in a dark room away from direct sunlight. Sun rays. This is necessary in order to prevent the adhesive from sticking to the protective film. Also when long-term storage It is forbidden to stack pallets with packed shingles on top of each other, otherwise the adhesive composition may stick to the protective film as a result of strong pressure from above.

Important to remember! Bitumen coating in the hot summer it becomes very soft, traces remain on it from a slight load, so when performing roofing works It is recommended to use special “manholes”, mats made from plant fiber.

Conclusion

Using the instructions for installing a soft roof, all the work can be done independently. And when caring for such a coating during the operational period, it is necessary to use tools that do not have sharp ends.

Currently, the roofing materials market is quite diverse. For the construction of a roof, anyone can choose an option in accordance with their preferences and practical tasks: from ordinary asbestos-cement slate to expensive composite tiles.

Shinglas soft tiles differ from other types of expanded flexible tiles color scheme And unusual cutting her scales.

One of the most convenient to install and at the same time reliable materials is soft (flexible) tiles.

SHINGLAS soft tiles are rightfully considered the standard in the segment of flexible roofing materials. If you follow all the manufacturer’s recommendations during installation, the roof will have an aesthetically attractive appearance and will last for a long time. The technology for laying Shinglas is quite simple, so installation can be done without the involvement of professional roofers.

Conditions for laying soft tiles

It is important to remember that it must be at least 12% - only in this case can you use soft tiles as a roofing material. If the roof slope is less, then moisture will be retained at the joints and such a coating is unlikely to last long.

The air temperature must exceed 5 degrees Celsius, so professionals advise installation in summer time. This is due to the fact that the shingle - a sheet of tiles - is attached to the roof surface not only with nails, but also with the help of a special self-adhesive layer, which is located on inside leaf. Under influence solar heat sheets of soft tiles are soldered together, which ensures the overall tightness of the coating. At subzero temperatures this process does not occur, so the insulation may be of poor quality.

At temperatures above 25 degrees it is also not recommended, or all work must be done very carefully and not step on already installed areas of the roof. And if it is necessary to carry out installation in the cold season, the sheets of flexible tiles should be kept at room temperature, and when laying use a hot-air burner or a hair dryer.

Preparing the base

First of all, you should think about installing under-roof ventilation. Creation air gap between the base of the roof and rafter system necessary to prevent accumulation excess moisture, which can lead to the formation of mold and subsequent rotting of the coating. Proper ventilation is ensured by the following elements:

  • holes at the roof eaves for air flow;
  • air gap between thermal insulation and roofing covering;
  • holes in the upper part of the roof (at the ridge) for air outflow.

Shapes of cutting Shinglas tiles. Different shapes allow you to experiment with stylistic design roofs.

To ensure good air draft during ventilation, the lower holes should be placed evenly along the eaves, and the upper ones should be 10-15% larger than the lower ones. Ventilation duct between the roofing covering and the thermal insulation there should be at least 50 mm, and if the angle of inclination of the roof is less than 20%, then the width of the air gap should be 60-80 mm. By following this method of ventilation, the base of the roof will remain dry for a long time, therefore, the roof itself will last longer.

FSF plywood, chipboards, OSB, edged boards with an indicator are most often used as the base material for soft Shinglas tiles relative humidity no more than 20%. Most popular in given time The material for the sheathing is OSB board of European standard, which has moisture-resistant sanding on both sides. Installation of such slabs should be carried out with a spacing of seams and a gap of 3 mm, since the possible thermal expansion of the material must be taken into account. If edged boards are used as sheathing, then the maximum gap between them should be no more than 5 mm. To increase service life, all wooden elements, including rafters, should be treated with antiseptics and fire retardants.

Installation of the lining layer

Device roofing pie Shinglas: 1 - flexible Shinglas tiles; 2 - self-adhesive lining carpet; 3 - OSB-3; plywood; 4 - sheathing;
5. Rafter system.

When the roof slope is from 12 to 18 degrees, an additional waterproofing sheet is laid on the base under the soft Shinglas tiles along the entire surface of the slope. Laying is carried out from the bottom up with an overlap in both the transverse and longitudinal directions. Fastening to the base is done using galvanized nails with a wide head, and the overlapping areas are coated with a special bitumen mastic.

If the roof slope is more than 18 degrees, installation of an additional waterproofing carpet will be required only in places where leaks are most likely. In the valley, rolled material is laid 1 m wide, 500 mm for each slope, and overlaps should be avoided when laying the material along the entire length of the valley. Skates are getting stronger insulating material at the rate of 250 mm per slope (clause 2.4 of SNiP Ts-26-76), and along the eaves overhangs backing layer must be at least 400 mm wide (clause 2.6 of SNiP Ts-26-76). The overlap areas must be coated with bitumen mastic.

The top of the underlayment is reinforced with cornice and end metal strips to protect the edges of the sheathing. Installation of these elements is carried out with an overlap of 50 mm and using roofing nails.

Laying soft tiles Shinglas (Shinglas)

After strengthening the roof overhangs with metal strips, you can proceed to laying soft tiles. All installation work can be done by one person; you only need the following tools:

Roofing system "Shinglas": 1 - ridge/eaves tiles; 2 — ordinary tiles; 3 — point aerator; 4 - pipe sealing; 5 - lining carpet; 6 - valley carpet; 7 — pediment strip; 8 - solid base for tiles; 9 - cornice strip(dripper); 10 — sealing the joint with the wall; 11 — abutment strip; 12 - dormer window; 13 - drainage system.

  • work gloves;
  • hammer;
  • roofing nails (galvanized with a wide head);
  • bitumen mastic;
  • trowel for applying mastic;
  • chalk rope;
  • roulette.

You should start with the installation of Shinglas ridge-eaves tiles, which are laid on top of the previously fixed metal strips. You need to lubricate it first back side sheets with bitumen mastic, and they should be secured to the base of the roof using galvanized nails with a wide head. As a starting strip, you can use not only a special ridge-eaves tiles, but also patterns from ordinary sheets with cut petals.

Before you begin laying Shinglas shingles, you should mix shingles from different packs, as they may differ in shades. On the inner surface of each shingle there is a special protective film, which must be peeled off before laying the material.

The valley carpet is used for waterproofing the area of ​​internal bends (valleys) and junctions on pitched roofs.

Installation of the first row of tiles is carried out from the center of the slope to the edges - this will make it more convenient to align it horizontally. The shingles are attached to the base of the roof with the same galvanized nails, but you need to ensure that the heads of the nails do not cut into the material, but are flush with it.

The second row is also laid from the center, offset to the left or right by half a petal, with the bottom edge of each petal being flush with the top edge of the cutouts in the previous row. All subsequent rows are installed in the same way. Places where there is no self-adhesive layer, for additional protection need to be coated with bitumen mastic.

To prevent unevenness when laying rows of soft tiles, you can make appropriate markings on the slope using a chalk rope. Along the edges of the slope, the shingles of the tiles must be trimmed and additionally coated with mastic. And the place where the smoke or ventilation pipe it is necessary to additionally insulate it using a lining carpet, then coat the exit point and the passage element itself with bitumen mastic. It is also recommended to make a groove when installing the pipe to prevent snow from accumulating in this place in winter.

When laying shingles, you do not need to coat each sheet with mastic - this will only spoil the appearance of the roof. The laying technology must be fully observed; you should not try to lay out any specific design with soft tiles - it must be abstract.

To ensure that the roof lasts a long time and its appearance does not deteriorate, you need to follow the following recommendations:

  • the condition of the roof should be checked in spring and autumn, when leaks are most likely;
  • various small debris from the roof should only be removed with a soft brush;
  • various items with sharp corners delete only manually;
  • We must not forget to periodically clean the gutters so that water flows from the roof unhindered;
  • if it accumulates in winter a large number of snow, it should be removed only with wooden shovels to avoid mechanical damage to the roof;
  • carry out repairs if necessary various elements roofing and base.

The technology for laying soft Shinglas tiles is quite simple and does not require the use of additional equipment. If you follow all the recommendations of professionals, your roof will last a long time and will be pleasing to the eye for many years.

Surely you have seen that many buildings use soft tiles as roofing - piece material, giving the building unique look: modern, noble and visually attractive. Of course, behind this lies the work of installing the tiles, since only correct installation taking into account the manufacturer’s recommendations, it will enable the coating to last a long time, reliably protecting the building from negative impacts environment, giving it a presentable appearance. Naturally, this is a task for specialists; professional roofers successfully cope with it.

But what to do if the need arises to carry out work? on our own, without the involvement of specialists? For this case, we offer you an article, after reading which you will have knowledge of how flexible tiles are installed in practice.

The story about how the installation of Shinglas flexible tiles is carried out should begin with a description common device roofs. In most cases, an insulated roof is a multi-layer structure, and the tiles are only the top layer.

The quality of a roof consists of several components. As can be seen from the figure, the following are required: an aero element on the ridge, thermal insulation, vapor barrier, a drainage system and wind protection.

It is possible to achieve compliance with the required temperature and humidity conditions, which is necessary for any warm roof, only by using continuous vapor barrier and heat-insulating material a certain thickness.

To simplify the perception of the material presented below, the relevant terminology will first be given.


Top picture:

  1. Visible part.
  2. Overlapping fragment.
  3. Neckline
  4. Adhesive layer.
  5. Tab, petal, tile.

Bottom picture:

  1. Gable overhang.
  2. Cornice overhang.
  3. Endova.
  4. Ridge, rib.
  5. Roof ridge.
  6. Fracture of the clivus.

In general, all the measures necessary for installing a roof are as follows:

  • creating a foundation;
  • performing ventilation;
  • installation of lining material;
  • protection of cornice and valley;
  • installation of tiles.

Creating a Foundation

The base is a structure that performs several functions at once. The main one is the load-bearing role, because it is this element that holds the weight of the layers of the roofing cake lying above. The lowest layer is a counter-lattice, which is designed to create a ventilated space and hold the sheathing elements. The installation instructions for Shinglas assume the use of sheathing made from edged boards. Coniferous wood with a thickness of more than 3 cm is perfect here. Fastening is best done with self-tapping screws or using rough nails.

Role load-bearing structure When installing the roof, rafters play a role, which can be located at a distance from 600 to 1500 mm. The thickness of the wooden flooring can be selected taking into account the pitch of the rafters and sheathing (in the table below).


Wood during operation can expand from exposure to water vapor, moisture or temperature changes, so an expansion gap is required. For a board it is up to 5 mm, and for OSB boards 3 mm.

To create a continuous flooring, it is best to use OSB-3, FSF or boards with a moisture content of less than 20%.


When installing a soft roof with your own hands using large-panel flooring, it is best to fasten the sheets with the seams spaced apart. All wooden elements must be treated with antiseptics and fire retardants.

During the installation of wooden flooring, you need to ensure that the fragments of annual wood rings visible at the ends of the boards are oriented with the convex side up. If the foundation is created using damp wood, then the ends of the edged or tongue-and-groove boards must be secured using two self-tapping screws.

Ventilation device

In order for the under-roof structure to last a long time, you will need to perform proper ventilation. A similar system above a residential attic is especially important. For normal ventilation pitched roof holes will be required for the flow of outside air, channels for its circulation above the layer thermal insulation material and a hood, which is usually located at the top of the roof.

Installation of Shinglas soft roofing is usually carried out with supply and exhaust systems ventilation having a cross-section from 1/300 to 1/500 of the total insulation area. In order to attic reduced pressure was created, the number of exhaust openings should be 10 percent greater than those through which air flows. Compliance with this rule is the key to the presence of constant air draft.

Sometimes this technology is difficult to use, since the eaves are lined with siding. In such cases, it is best to use soffit strips, which are special elements that ensure the flow of outside air.

When creating channels above thermal insulation, it must be taken into account that their minimum height should exceed 5 cm at a 20-degree angle of inclination of the slopes. If the angle is smaller, then the height should be increased to 8 cm.

Do-it-yourself installation of a soft roof should be done in such a way that there are no zones where there is still air. So-called air bags can be easily eliminated if you properly think through the air circulation scheme.

Installation of lining material

The technology for performing the work involves two possible options. The first of them is used if the roof slope angle is in the range from 12 to 18 degrees. Here you need a special waterproofing carpet, and bitumen-polymer self-adhesive material is installed in the valleys and eaves overhangs.

In the valley it is laid on each slope of 50 cm, and on the eaves overhang the width is the sum of the eaves overhang and an addition of 60 cm in the direction from the plane of the facade. Ideally, one continuous carpet with no overlaps should be laid along the valley. If this cannot be done, then the size of the longitudinal overlap should be more than 30 cm.

When Shinglas flexible tiles are installed, a special underlay carpet (for example, produced by TechnoNIKOL) must be laid on the remaining surface of the slope. Roll material laid from top to bottom. Overlaps in the transverse direction should be more than 10 cm, and in the longitudinal direction more than 15 cm. Fastening to the base is carried out using galvanized nails with a wide head. Nails should be placed every 25 cm.

When the slope angle is more than 18 degrees, then you need to protect those places where leaks are most likely to occur using a waterproofing carpet. This category includes cornices and gable overhangs, slope ribs, valleys, roof outlets and ridges.

Valley and eaves overhangs are protected using self-adhesive bitumen-polymer type material. Dimensions are selected as in the case of an inclination angle of less than 18 degrees. Insulation roof outlets carried out using a 1 m wide lining carpet, fixed around the perimeter with nails. The remaining areas are covered with the same material, but 50 cm wide.

Overlapping joints should be coated with bitumen mastic (for example, FIXER mastic).

Cornices and valleys

The technology for laying Shinglas material, the installation of which can be done by hand, involves strengthening the roof overhangs through the use of eaves and end strips. They are laid over the lining material with an overlap (3-5 cm), and fixed with special nails in increments of up to 15 cm in a checkerboard pattern.

Installation of material in valleys can be done open method or using the undercut method. The most preferable is the first case, when a valley carpet is mounted on top of the lining material. On the reverse side, it is coated with bitumen mastic on the perimeter.

In construction, the saying “butter and butter” is not always appropriate, and roofing technology is one example of this. It is worth saying that there is no need to be zealous and waste the mastic in vain, since this will not give any effect.

Installation of tiles

This procedure begins with marking the slope.

Professionals advise applying marking lines to the slope to make it easier to level the finish coating. The vertical marking pitch is selected in accordance with the width of the row tiles, and the vertical distance between the lines is selected equal to the width of 5 rows.

Marking lines are just guides. They should not be considered a guide and the tiles should be nailed strictly according to the markings.

The Shinglas installation instructions assume the use of galvanized nails with a wide head. Their number depends on the slope of the slope, and the reliability of the fastening depends on how the nail was nailed. Correct option shown in the figure below. The tiles should be nailed at a distance of 2..3 cm from its edge, and the head of the nail should be in the same plane with the surface of the covering.

Styling finishing coating They begin with the installation of eaves tiles, but this line can also be made in the form of a pattern from ordinary ordinary tiles. When working on a long slope, it is best to start installation from the middle. The edge of the first row is aligned with the line of the middle of the slope, and the beginning of the second row is located in one direction or another by half a petal. Bottom edge the top row should be flush with the top line of the cutouts in the shingles below. The third row is laid relative to the second in the same way as that one is relative to the first.

When installing the coating along the edges of the valley, nails may be used no closer than 30 cm from the central axis. Excess material is trimmed and Bottom part coated with mastic.

Above we discussed the main points regarding Shinglas tiles, the installation of which is easy to do yourself. In this material, methods for arranging junctions were omitted, since they differ little from other technologies for installing soft roofs.

You should not save, and it is better to use a soft roof. Although the ease of installation makes the price per 1 sq. m. acceptable for average income. Today we will look at Shinglas roofing, installation technology, properties, pros and cons. The most important thing is that the service life of this coating is about 60 years, of course, subject to the technology.

  • ANDEREP GL - the principle of design and structure is the same as that of soft tiles, it is fastened in the same way mechanically, and does not require the use of mastics to seal the seams. Used mainly under soft tiles.
  1. Roofing nails. This is a steel fastener covered with stainless steel on top, the diameter of the nail head is at least 9 mm. And also the diameter of the rod is not less than 3 mm. Fastener consumption per 1 sq. m. is 80 gr.


And now we will tell you why we chose Shinglas tiles.

Because like tiles, so is everything auxiliary materials and components are manufactured by one manufacturer, Techno Nicole, and can be purchased in one place. Which is very convenient and saves a lot of time.

Installation of flexible Shinglas tiles

As we all understand, installation consists of many stages. The initial stage is the creation

Bases for laying

You should start with the fact that work should be carried out in a warm, rainless season.

We attach a membrane film to the rafters, which will protect the insulation from moisture.

We fasten the film using counter lathing.

The insulation is laid with bottom side membranes between rafters. We attach the counter batten to the counter batten in increments of 20 cm.


As a basis we choose the most best option, this is OSB-3 (oriented strand board), but plywood and other building materials can also be used.

It should be secured in the form brickwork using nails and screws. The seam between the plates must be left 3-4 mm. for thermal expansion.

When you use flexible tiles from the Western and Continent collections, the base should be made at least 12 mm thick. For other collections, a thickness of 9 mm is sufficient.

Laying technology of the lining layer


We looked at the types of lining option above, it should be noted that for the valley area they use a self-adhesive lining layer ANDEREP, it is advisable to use one roll for the entire length, but if this does not work out, then the overlap should be at least 30 cm and do not forget to carefully glue the joint . The width of the lining carpet should be 1 m, 50 cm from each edge.


In the area of ​​the eaves overhang, self-adhesive material ANDEREP is also used.

The material is laid to the very width of the cornice overhang, as well as about 60 cm inside the building.

This installation method prevents water from entering.


The entire remaining surface of the roof is covered with lining material with mechanical view fastenings Laying can be carried out both in the longitudinal and transverse directions. From bottom to top, in the longitudinal method with an overlap of at least 10 cm. In parallel eaves overhang, overlap of at least 15 cm. With any method, the joints must be treated with Fixer over the entire width. The underlayment is secured to the roof surface using roofing fasteners.

It should be noted here that after the lining material is attached, markings are applied. The markings allow you to lay soft tiles evenly, both vertically and horizontally, but this does not mean that you need to nail the tiles along these lines. It’s simple: the vertical strip is equal to the width of the tile itself, and horizontally, every five rows are minus 80 cm.

Installation technology of flexible shingles tiles


We fix the starting line, this is where it begins. You can use special ridge-eaves tiles or the tiles themselves, only after cutting off the petals.

We retreat about two centimeters from the edge of the roof and glue it on top of the lining layer and nail it.

After this, we begin the installation of the initial row; experts recommend starting from the center of the roof and, unforgettably, retreating 2 cm from the edge of the starting layer.

The next layer is mounted in the same way from the center, but shifted to the left or right by half the petal. So we continue to glue and nail the tiles in each subsequent row, and do not forget to shift them.


The shingles in each pack may vary slightly in shade, so you should mix several packs. The tiles are nailed with galvanized nails, the main thing is that the caps are in the same plane with the roof surface.

For different shapes tiles have different quantities of fasteners and fastening methods.

So for Dragon Tooth, the place where two layers of tiles overlap is simultaneously secured with a nail to make it easier to hammer in; the manufacturer marks the front surface of the roof with a thin line.


The Continent collection should only be fastened with nails 45 mm long.

The edge of the tiles along the edge of the roof should be sealed with impregnation to a depth of about 100 mm. this allows you to protect the roof from side rain. It is recommended to heat the adhesive layer with a hair dryer.


We bring the top row to the ridge and cut it by 2-3 cm, to the edge of the metal strip, to beat off the water. On the other side of the roof the sequence is the same. Ridge tiles are also used for arranging ribs. Near the ribs and slopes, the coating is trimmed so that there is a gap of about 50 mm. Ridge tiles, laid from bottom to top, with an overlap of about 5 cm. Fastening is done with nails, 2 pcs. from each side.

The Ranch, Jazz, Country, Finnish and Classic series of tiles must be bent only on a heated metal pipe, this is done specifically so that the tiles accept the required form and did not burst at subzero temperatures.


Where the roof adjoins the wall, it is necessary to fill the wall with wooden slats in the form of a triangle, onto which the edge of a row of tiles is placed.

The wall should also be treated with a primer. A ridge tile is laid on top of the row of tiles.

With an overlap on the prepared wall, but not less than 300 mm.

We carefully process all joints, seams and surfaces.

Roofing care


As with any type of coating, for shinglas tiles requires maintenance and repair.