Decoration in the yard from bottles of different shapes. Ideas from plastic bottles for home and garden! plastic bottle garden paths

A plastic bottle is not just an ordinary waste (garbage), it is a decor option, with its skillful use. Bottles, depending on the liquid stored in them, vary in shape, color and size. These features will allow you to interesting crafts from plastic bottles to give their own hands.

massive buildings

Plastic bottles are used in this case as a substitute various materials all kinds of structures. They can replace bricks and even slate. To give the necessary strength, the bottle is covered with sand, and in order to achieve certain form, use pressing and scissors.

Gazebos, greenhouse buildings

The essence of the building is PVC installation products using fastening materials in the form of wires or ropes. In the end, when using sufficiently strong frames, worthy supporting walls come out for any structures.

Enclosing elements

The principle of crafts is the same as in the paragraph described earlier. It is also possible to decorate an existing fence or gate with plastic bottles, cutting them, and gluing mosaics.

Sheds

The structure can be used by you as a shelter from the rain. You can hide not only yourself, but also leave a car or equipment. For the construction, you need to install a solid frame, on which bottles are attached with wire.

Water heater

At proper construction and combining containers, you can do Summer shower, whose water will be heated in bottles under the influence of sunlight.

plastic furniture

Bottles can be used to make outdoor benches, chairs, and even sofas that can be upholstered for more comfort.

Plafonds for lamps

Use plastic bottles that are not heat-affected. You can make a ceiling lamp of any shape and color, depending on the design. suburban area and the requirements.

Flower pots

Usually bottles act as containers used for primary planting, but with skillful processing, beautiful pots and planters can be obtained.

Flowerbeds from plastic bottles

By giving the bottle physical processing in combination with other fixing materials, such as stones, you can mount an exquisite flower bed and, if necessary, paint over the resulting products.

birdhouses

Hanging products from bottles for bird feeders are made literally in a couple of cuts at the base of the bottle. At additional processing, the feeder can look quite aesthetically pleasing.

home decoration

All kinds of animal shapes, lanterns and even curtains can be made with a skilled hand.

boats

With a certain number of bottles and a couple of video tutorials, you can make your own boat and go fishing.

Playgrounds for children

It is possible to cut figurines, slides, for plant lovers - artificial palm trees, flowers and much more.

Land cover installations

animal figures, aircraft and much more. The most popular crafts and instructions for making them are described below.

Swans-planter

To make original design in the form of a swan, we need a certain number of large bottles (approximately 5-6, depending on the size of the bird), as well as:

• copper wire or any available metal;
• putty (finish);
• metal grid;
• tight material (bandages, gauze);
• knife (for shaping);
• spatulas of various sizes.

Step by step production:

1. Cut a large bottle lengthwise, do not try to make two identical halves, this is completely unnecessary for crafts. The approximate shape as a result of such an operation should resemble a voluminous flowerpot. Next, pour in wet sand in order to achieve the desired deformation of the bottle.
2. We fasten the wire to the lid, having previously made a hole in it. To facilitate this process, you can use a heated nail or hand drill. The wire will become the neck of the bird in the future. We throw the diluted putty on the prepared polyethylene bedding with a layer of 5-6 cm. Place a bottle of sand on the resulting kind of foundation, which was discussed in the previous paragraphs. Using a spatula and mortar, give the body of the swan the desired shape.
3. Give the wire a curved shape resembling a neck. Fasten the rolled ovals of putty onto the wire and secure everything tightly with gauze or bandage. The transition from the base of the swan to the neck should not be abrupt, otherwise the design will turn out to be unaesthetic. At the end of the wire, make a head out of putty, adding eyes and a beak.
4. We attach a metal mesh to the body with a solution and get wonderful wings. A solution is applied to the mesh and the result should be wings of the shape you have chosen. The process is quite painstaking, so be patient and strong. Using spatulas, shape the curves inherent in the swan.
5. After drying, sand the resulting product with emery. The next step is to prime the bird and paint, remembering to draw all the attributes of the swan's face.

cacti

Enough original idea and very easy to install. With the help of wire we make the base of the cactus and fix it in the ground. After, we dress the bottles of the required shape and color.

Flowers

To make plastic flowers, we need to have:

• knife and scissors;
• bottles of the required shape and color;
• paints and varnish for finishing works.

Step by step manufacturing instructions:

1. Cut off the top of the bottle. Next, make a few cuts to the base with scissors. One strip should be wider than the next three, as it will represent the petal, and thin strips will play the role of stamens.
2. Strips with a large width are cut with scissors, giving them a sharp shape. Thin strips are twisted with a knife and bent down.
3. Petals - wide strips are painted with green paint or varnish.
4. The stand is made from the remaining material by cutting the bottle in half, not reaching the bottom 4-5 cm. The middle of the bottom remains intact. Give the workpiece the appropriate shape and place on the ground.

Owl from discs and bottles

Necessary materials:

• bottles of different sizes (2 x 5 liters and 40 x 2);
• special glue (epoxy);
• self-tapping screws for fastening;
• discs and beads for the eyes;
• knife and scissors;
• styrofoam for framing.

Manufacturing instructions

1. The outlines of the future face are organized by cutting it out of polystyrene, also take places for the eyes. With the help of packaging from tablet batteries, we make eyes. Inside the empty package we place the beads and pour epoxy glue there. After drying, the eyes are attached to the head. If desired, ordinary CDs can be glued in front of the beads, which will give the eyes a more interesting look.
2. Having chosen a dark-colored bottle, a beak is cut out of it, which is then attached to the head in Right place. The rest of the bottle is not thrown away, you can make feathers out of it. After cutting, the feathers are glued along the counter of the eyes. Eyelids are cut out of the remaining plastic, which, when glued, should overlap the attachment points of the feathers.
3. The next step is making the wings. Taking a large bottle, organize a frame for wings from it, pre-cut feathers from a two-liter bottle are attached to it. By gluing feathers, you must close the neck big bottle. After, in several rows, attach smaller feathers, and the last row using a knife, bend over the base of a large bottle.
4. Using the second large bottle, make the base for the owl's body along with the back of the head. The body is glued with feathers in several rows, as are the wings. The part on which there should not be feathers is the back, everything else is covered with feathers in random order.
5. Using self-tapping screws, we fasten the resulting parts (head and wings) to the body of the owl. Before that, glue the back of the head with cutouts from the middle of the bottles. The joints are also glued with feathers. After fixing all the details, paint the owl in the desired color.

bottle pig

Necessary materials:

• bottles different sizes(one 5-liter and 4 one and a half liter);
• aracal the color of the future eyes and nose;
• nails for fastening;
• knife and scissors;
• paints or markers;
• pen or pencil;
• paper.

Manufacturing instructions

1. One and a half liter bottles are cut diagonally so as to get rid of the neck. The cut off part will serve for the hooves in the future. Draw the eyes, ears and nose on paper. Using a marker, move the drawn outline to the aracal. The part of the bottle left after the circumcision is used to organize the ears. From any bottle, cut the tail and give it a twisted shape with a knife.
2. After marking the places for future attachments for the ears, hooves and tail, use a preheated nail to make holes. Details at the attachment points are notched and at the joints the resulting edges are bent for greater strength.
3. The last step is painting the piglet. After it dries, glue the eyes and nostrils. Paint the hooves black. The piglet is ready, you can install it in a flower bed or anywhere in your summer cottage.

palm trees

Necessary materials:

• bottles of the desired color (green and brown);
• knife and scissors;
• copper wire or rod.

Manufacturing instructions:

1. Cut the bottle in half, make notches in the shape of teeth on the top. Prepare as many blanks as possible, as palm trees should be large.
2. A metal pin or thick wire is attached to the ground. It is necessary to take care of the reliability of fastening so that the structure does not fall in the future.
3. Plastic blanks are strung on a pin and bent over for a more natural structure of the palm tree.
4. Green bottles are needed for branches and leaves. With the help of scissors, the bottom is cut off, and the rest takes on the necessary shape with the help of cuts. The shape of the leaves can be any, it all depends on your imagination.
5. The last stage is fixing the leaves on the pins and connecting all the details into a common design. In order to fasten everything together, you can use welding or ordinary harnesses, which can be purchased on the shelves of any hardware store.

flowerbeds

Necessary materials:

• cement and sand;
• crushed stone or gravel;
• a tire or a barrel cut in half;
• bottles (can be glass).

Manufacturing instructions:

1. Install the blank in the place of the future flower bed.
2. Prepare a solution (mix cement with sand in a ratio of 1: 2, gradually adding water).
3. Coat the workpiece with a solution (the layer must be sufficiently dense) and insert the bottles with their necks into the solution. When inserting bottles, follow the checkerboard pattern.
4. After hardening to the bottom of the workpiece, pour gravel or slag to organize drainage. After, fill the flower bed with earth. The design is ready, now you can plant it with any flowers of your choice.

Crafts from the bottom (bottom) of the bottle

The bottles are cut (the lower halves are taken for work). The color scheme can be any according to your taste. After organizing the embankment from the soil so that a slide of the desired diameter is obtained from it, blanks from bottles are stuck into it. With a dense arrangement of bottles and the right color, original plastic buildings are obtained.

Decorating country beds

In order not to waste time on solid plastic crafts, you can simply decorate the site by making contours for the garden or paths using plastic bottles. The bottles are cut, the neck is removed to the point of narrowing, filled with sand or earth and dug in along the contour of the garden bed, flower bed or plot.

If necessary, the bottles are painted, which gives your frame an even more aesthetic appearance. This type of decor is quite diverse, since it is possible to organize any shapes and colors according to your desire.

planter

Hanging pots or just mini flower beds are easy to make from plastic bottles. Cutting off the top, we get a straight pot, cutting off the bottom - cone-shaped, or the middle - for hanging models. After, the workpiece is covered with soil and the plants you need are planted in it. Bottles can be dyed or left clear. You can install models of pots along the path or decorate the fence with hanging planters.

bottle fence

Making a fence, in principle, is simple, such a building is very economical and will allow you to protect the site from the penetration of animals and other unwanted guests. For the construction, pins are used, tightly fixed in the ground, on which plastic bottles are strung.

Bottle gazebo

In the presence of required material and free time you can make a gazebo. To base the gazebo, you will need a lot of wire and rods. The foundation can also be made from plastic bottles filled with sand or earth. If desired, the gazebo can be covered with a protective cloth or tarpaulin. Components of the bottle can be painted and easily replaced at any time.

Trap for bloodsuckers

To make a mosquito trap from a plastic bottle, you will need a two-liter container, which is then cut in half. The upper part is turned over and inserted into the lower one, organizing a funnel, and the lower one, in turn, is filled with sweet water. Then the entire workpiece is darkened by painting or gluing. The trap is ready. To attract flies and wasps, you can add a little jam, honey or syrup to the container.

Pugach for moles

For this craft, make three cuts in the bottle, and bend the plastic so that you get the blades. Pour small stones at the bottom of the bottle, and put the bottle itself on a rod buried in the ground. In the presence of minimal wind, the structure will produce sounds that are not tolerated by moles.

Irrigation structures

Bottles can also be used to water plants in your summer cottage. Uniform watering can be organized in several ways. A variant is possible with an incision in the bottom of the bottle and digging its neck into the ground. Before burying the neck, a hole is made in the lid, and grass is laid on the bottom of the hole to prevent clogging of the lid with earth.

You can also cut off the bottom of a plastic bottle and hang it over a flower bed or on desired area plantations. In this case, watering will be carried out through the neck of the bottle with a loose lid. Irrigation is regulated by more or less twisting of the plug.

Crafts from covers

When working with plastic bottles, a sufficient amount of corks may remain. Proper use of them can breathe new life into them and help avoid the disposal process.

Cover curtains

The organization is very simple, with the help of a drill or a thin nail, holes are made in the covers of different colors and with the help of a fishing line the elements are attached to each other and to the eaves.

Cork pictures

With some experience and a sufficient number of covers of different colors, you can make a wonderful decor for any surface.

When working with bottles of any size and color, make sure they can withstand the weather conditions in your climate area. Before carrying out any operations, take care to remove the labels from the surface of the bottle.

Conclusion

Plastic bottles and caps do not have to be thrown away after their direct use, they can be indispensable decorative elements for your dacha. After reading this article, you will be convinced of the secondary rational use plastic containers and you can make them good crafts with your own hands.

Plastic bottles - affordable and inexpensive material, which, in addition to its direct purpose, can be used to decorate a personal plot. From plastic, you can create a lot of decorative and practical elements. landscape design that will be original, strong and durable.

The main task of craftsmen and amateurs to build crafts from improvised means is to collect as many bottles of different sizes and colors as possible, show imagination and bring it to life.

Recycling bottles: functionality and decorativeness of plastic products

During holiday season many summer residents accumulate a lot of empty plastic bottles left over from picnics. You can send them to a landfill, or you can use them to change the surrounding space and make unusual accessories to decorate the garden.

Recycling plastic bottles for home improvement garden plot has a number of advantages:

• saving money that would have to be spent on the purchase of finished design products;
• exclusivity and originality of the created crafts;
• change in landscape design as soon as possible- working with plastic bottles is very simple and usually it takes from 2 hours to 2 days to make a simple craft;
• the opportunity to show their design abilities - the finished product will emphasize the creativity and creative potential of the owner of the plot;
• bottle reuse reduces clogging environment, because, as you know, it will take many years for the complete decomposition of plastic in natural conditions.

On a global scale, an abundance of plastic has been adapted for the construction of floating islands, residential buildings, energy-saving systems and large installations.

On the local scale of the suburban area plastic bottles found their application in the creation of:

• flowerbeds and flower beds;
• flowerpots and planters;
• garden gazebos;
• canopies and hedges;
• ornaments for a garden and reservoirs;
• country furniture;
• lampshades for lamps;
• garden paths;
• figurines of animals for playgrounds.

There are many ways to use waste packaging. Consider the most interesting ideas of reincarnations and describe the process of creating DIY crafts from plastic bottles.

Crafts from plastic bottles - original elements of landscape design

creation of flower beds and flower beds

Plastic bottles can be used as a low fence for a flower bed or container in which flowers and garden plants will grow.

For fencing flower beds, the same 1.5-liter bottles are better suited. To brighten up the landscape plastic container before installation, it is desirable to paint in yellow, red or Blue colour(green - not recommended, as it will be "lost" against the general background of plants).

Work order:

1. It is necessary to determine and outline the contours of the future flower bed (they can have the most intricate configuration).
2. To ensure the strength and stability of the structure, plastic bottles must be filled with sand or earth.
3. Dig a row of bottles along the perimeter of the flower bed so that there are no gaps between the elements of the fence.

As a result of the work done, a well-groomed and tidy flower bed will turn out.

Large plastic bottles make an excellent flowerpot or flower pot, the main thing in the manufacture is not to forget to make drainage holes in the bottom.

Let's consider step by step the creation of a hedgehog flowerbed, in which you can plant the most different plants: cacti, high lawn grass, perennial dwarf shrubs And so on.

1. As a basis, you need to use a 2 or 3 liter plastic bottle. It is cut in half lengthwise. The front part of the container must be wrapped with nylon tights or burlap - this will be the muzzle of a hedgehog.
2. The fabric is glued or stapled together. From black buttons and a black piece of fabric, you need to make eyes and a nose of a hedgehog, and then sew them to the base.
3. Make holes for drainage at the bottom of an impromptu flower bed, fill it with earth and plant plants (it is desirable that the shape of the leaves resemble needles).

The result of such creativity will undoubtedly please all visitors to the garden plot, especially children.

The original decoration of the garden will be an "all-season" flower bed, lined with multi-colored plastic bottles.

After placing all the bottles, as shown in the diagram, the flower bed must be given clarity and stones laid out along its contour.

Near the house, gazebos or throughout the garden can be placed hanging planters from bottles.

decorations for artificial reservoirs

The surface of the pond can be decorated with homemade water lilies or non-trivial daisies. Flowers from plastic bottles will add picturesqueness to the pond and attract attention beautiful butterflies and dragonflies.

To create water lilies you will need:

• white and yellow plastic bottles small capacity(1-1.5 liters);
• plastic bottle of 5 liters;
• candle;
• scissors;
• green paint;
• glue.

Progress:

1. From the yellow bottle you need to cut off the neck - this will be the core of the water lily. Make 8 cuts in the neck at the same distance from each other and give each part a rounded shape.
2. For the manufacture of stamens, we use the rest of the bottle. We cut a strip about 4 cm wide and across, up to half, we make cuts every 0.5 cm.
3. We turn the blank of stamens and bring it to the flame of a candle (the distance to the fire is about 5 cm). The stamens should curl inward.
4. We also hold the core over the fire, so that the petals are slightly bent.
5. We glue the stamens and the core.
6. From a white bottle we cut out oblong petals of a water lily and fasten them with glue to the neck of a flower.
7. From the bottom of a large bottle, cut a leaf for a water lily and paint it green.
8. The flower must be "planted" on a leaf and sent to sail through the pond.

Daisies from plastic bottles will help decorate both the pond itself and the area around it.

You can make a palm tree from plastic bottles and place it near the pond - this will add exotic landscape design.

Bottles with a cut bottom (dark color) are exposed and pressed tightly against each other. The number of bottles used determines the height of the palm tree. A neck from a green bottle is attached to the top of the palm tree, through which five wires (the bases of palm leaves) are made.

Green bottles are strung through the neck on a wire. Green plastic is cut into strips, imitating palm leaves.

Around the pond, you can seat funny frogs that will enliven the landscape of the site and cheer up the guests of the garden.

plastic bottle garden paths

Interesting solution - garden paths for giving from a plastic bottle. Paths can be laid out from whole bottles filled with sand, or from their bottoms.

Bottom paths look neater, but it will take a little more time to create them:

decorative figurines and installations

A modern and popular trend in garden landscape design is the creation of voluminous installations and small decorative figurines from improvised materials, including plastic bottles.

On the branches berry bushes, on fruit trees or in a flower garden you can "settle" bright bees from plastic bottles. Such a decoration is impossible better fit suburban area on which the apiary is located.

To make one bee you will need:

• 1 liter bottle with a wide neck;
• 2 ribbed bottles;
• wire;
• 2 white lids;
• scissors and glue;
• paints (gouache) and varnish;
• napkins;
• a piece of black wire.

Work sequence:

1. Paste the base of the product (bottle) with napkins, dry it and paint it with gouache in yellow-black color. Open the surface of the craft with varnish - this will save the “bee” from dampness.
2. Cut out 4 wings from the ribbed base, shaped like leaves.
3. We form a bee stigma. We glue the eyes (small white covers) and the mouth (a piece of black wire).
4. We attach the wings to the base, and draw pupils on the eyes.
5. We make paws from wire, there should be three pairs of them. We fasten the paws to the bottom of the base (under the wings).

Can do swarm of bees using bottles of different sizes.

More time and materials will be required to create a three-dimensional installation in the form of different animals. You need to be patient, because you need to lay out whole containers or parts cut out of them according to a certain pattern.

The playground for children can be decorated with funny animals made of plastic bottles. Such figurines are easy to make and can be made together with the child.

uses for plastic bottle caps

Corks from plastic bottles are also used as landscape design decor.

Most interesting options lid applications:

To create a composition you will have to stock up big amount lids different color so plan future craft It is necessary in advance so that there is time to search for material.

Practical use of plastic bottles

country house and garden gazebo

On a small summer cottage, you can build a house or garden gazebo using ordinary plastic bottles filled with sand instead of bricks.

The walls of gazebos, greenhouses and houses are laid out in a checkerboard pattern using cement mortar. When working, you need to take into account some of the nuances:

• plastic does not come into contact with cement mortar like a brick, so you need to make holes in the container - the cement will interact with the sand inside the bottle;
• to improve the adhesion of the surface of the bottle with the solution, it is desirable to lay a reinforcing grid between the rows of masonry;
• in the process of laying, the rows of bottles must be fixed with a rope or wire so that they do not move apart.

Under the influence of frost and heat, plastic is destroyed, so the life of bottle structures is small - about 5-10 years

Garden furniture

Plastic containers - unique material to create practical outdoor furniture. You can independently produce traditional or exclusive, avant-garde furniture models.

Plastic bottles can be quickly and easily turned into a neat and comfortable ottoman for the garden.

1. Empty open bottles should be kept in the cold (in the summer you can put them in the freezer for a while). Even in the cold, close the bottles and bring them into heat - the air inside the eggplants will heat up, expand and prevent the container from deforming during operation.
2. Connect the bottles with double-sided tape. First in pairs, and then - in the overall composition.
3. We cut out the shape of the seat of the ottoman thick cardboard and foam rubber, glue together.
4. Wrap the ottoman around the perimeter with foam rubber or batting, and attach a soft seat on top.
5. Sew a cover for an ottoman: cut out the top (circle or square) and a rectangle (the walls of the ottoman) from the fabric, sew together, leaving room for insertion.
6. Attach the design and sew the cover by hand.

An ottoman made of plastic bottles turns out to be very light and practical, it can be placed in the garden, gazebo or in a country house.

fences and canopies from plastic bottles

You can save a lot on arranging a fence or a carport if you make a structure out of plastic bottles.

The finished canopy will have a plastic structure and an unusual configuration, it will create a protective barrier from the sun and precipitation, and also decorate the garden.

To delay Sun rays the bottom of plastic bottles must be painted

1. In a plastic container with a hot rod, you need to make through holes and pass through them a fishing line or rope. Form several rows in this way.
2. Between themselves, the rows are connected by perpendicular ties through another pair of holes and material for “firmware” (fishing line, rope, wire).
3. The "bottle" canopy is attached to a metal or wooden frame.

A wave-like effect can be obtained by attaching the canopy to the racks. different lengths

useful recycled crafts

If the question "What to do with plastic bottles?" remained unresolved, we suggest that you familiarize yourself with useful crafts, which will be useful on any personal plot.

Do not be afraid to experiment and go beyond the usual, and then the most ordinary things will turn into a real work of art.

Sometimes bottles of water or other liquid are not only a pile of useless garbage, but also an interesting construction material. You just need to look closely at it.

The masterpieces created from plastic really impress with their diversity and originality. Most often, we throw away such things so that they do not create unnecessary rubbish in the room, but do-it-yourself crafts from plastic bottles are also great way save on expensive interior details.

Learn to give plastic bottles a second chance and you will never regret it.

Advantages of using plastic bottles for decoration

• - Firstly, this material will cost you very cheaply. You do not have to buy it additionally, just take the used container.
• - Secondly, by making crafts from plastic bottles for summer cottages or at home, you make our planet a little cleaner.

When we throw plastic products in landfills, we often forget that such things take 1000 years to decompose! It is too long. Imagine how much garbage will accumulate over this millennium if humanity does not invent more rational way its disposal.

Thirdly, products created from this material are very durable, so you don’t have to worry about the durability of your man-made masterpieces.

Decoration for giving

If you have a little time, perseverance and patience in reserve, then you can make many masterpieces that will decorate the territory of your home. Below is a description of crafts made from plastic bottles. Birds are one option. Such a decorative element will be a great addition to any flower bed or lawn.

In order to make, for example, a swan, you need to stock up on a large plastic bottle of 5 liters; several dozen small white bottles of 200 ml. This may be a container for dairy products; wire, hose, scissors, paints and a lighter.

From a large bottle we cut out the body of our future swan, as shown in the photo. It will be much easier to do this if you outline yourself the lines along which you will navigate. Now take the hose, thread the wire through it and form the neck of our bird.

In order to decorate the frame of the product, we will use small bottles. Each of them needs to be cut as follows:

• - cut off the top and bottom;
• - cut into oblong pieces that will play the role of plumage;
• - punch holes in each feather;
• - process their edges with a lighter to smooth out irregularities;
• - string them on the wire, simultaneously fixing and securing.

To make the swan's head, cut off the bottom of one of the small bottles. Now it's time to connect our design and paint it with paints. The swan is ready!

To please children, you can make beautiful and bright butterflies that will become wonderful decoration both indoors and outdoors. The manufacturing process itself is quite simple, so you can involve your baby in it.

Let the design of children's crafts from plastic bottles be a small lesson in labor for him. In order to build this design, you need to take one plastic bottle, cardboard, scissors, wire, paints and beads.

To make a butterfly, you need to draw a template on cardboard, and then cut out the outlines from plastic. Now fix the wire in the center of the butterfly, where it will bend.

Attach the antennae to the butterfly from the same wire, decorating them with beads. You can color the insect wings as your fantasy tells you. Butterfly is ready.

Do-it-yourself ladybugs will also look original in the flowerbed. In order to make such beauty, take 2 bottles of 0.5 liters and one liter; scissors, paint, glue.

To create myself ladybug, must be taken as a basis liter bottle, paint it black, leaving two white areas on the lid, which will symbolize the eyes of an insect.

Now, from two smaller bottles, cut out the wings of a ladybug and paint in red with black dots. This design must be fastened with glue. You can decorate an insect by adding a smile and antennae from the same plastic to it.

We hope that this information was useful and interesting for you! As a nice bonus, we have posted below a lot of photos of crafts from plastic bottles.

Photo of crafts from plastic bottles

Hello friends!

I continue the summer theme, last time we reviewed. Decorated the garden and garden with the cutest products, remember? We also took a look at what's new this year. Today we continue to draw up our sites, and you know what? Yes, regular plastic bottles.

With great popularity, such wonderful toys or how to call them creations are gaining more and more recognition among summer residents. Do you know why? Of course, because we all always have a couple of unnecessary bottles in the apartment that lie and gather dust on the shelf. So why don't we take and build gizmos from them that will delight not only the eye, but everyone around.

Ah-ha, let everyone go and envy such beauty. Or maybe they will come up with something extraordinary new and will brag to you. Along the way, soon competitions and exhibitions will be held in cities and villages, as well as competitions best work. And why not, so to speak.

After all, it's really great, and most importantly, it inspires everyone else to come up with cool and unique compositions year after year. Well, get acquainted with the content and quickly scroll through and look at the beautiful masterpieces that I tried to find on the Internet. Intrigued? This is good.

The PET material is lightweight and also durable, so you can easily and quickly make any thing out of it. I'll start by showing huge Vehicle. Oh, and now there will be impressions.

Any bottles, even canisters, will do for this purpose. Look at how many jobs there are. If you have children, they will be interested in such products. Choose any work and make a whole composition on your backyard.

You can also take equipment or helicopters as a basis.

From a jar for shampoo, you can also make a masterpiece and get an airplane. Colorize acrylic paints so that weather conditions do not spoil the craft.

All the same, the furniture looks wonderful, it would seem, wow. Of course, here you need quite a lot of the desired material.

Entire houses are already cultivated and greenhouses and greenhouses are being built. Also, gazebos made of such waste materials began to be in demand.

And of course, furniture items such as chairs, stools and trash cans. Well, everyone will love it for sure.

You can also make an ottoman and place it, for example, in a bathhouse or in a gazebo. Therefore, do not throw away juice cans.

And under them place the mushrooms, and it can be fly agaric. Dream and success will come by itself.

For the fence they also do decorative ornaments, cut the bottoms of the bottles and lay out stories.

They also decorate stumps and benches. It comes out bright and beautiful.

On playgrounds, as well as schools, flowers and the sun are cultivated. These are the most famous works.

And of course, you can’t do without flower beds and flower beds. You can even make from one ordinary transparent soda bottle. What a wonderful mouse came out.

Or make ordinary pots and plant any climbing plant or a flower.

Looks quite wonderful and cute, even look magic ball built.

Whoever is ready for something, then creates. It surprises us, but we take an example and do not lag behind.

This picture is also very beautiful, but imagine if you still plant daisies or other flowers and how it will all bloom.

Also unusual butterflies will be a great decoration. They will cheer up and make the interior even more beautiful.

You will need a template, cut it out of paper, and then attach it to the bottle.

Circle and paint with acrylic paints, and then cut along the contour.

Or these funny turtles.

Make them with your kids and decorate the porch or dressing room. Here is a step-by-step photo instruction for you in detail, by the way, this is also a piggy bank.

Interesting work from plastic bottles for beginners (photos and descriptions are attached)

If you are a beginner and think that you will not cope, then you are deeply mistaken. Nothing is impossible, start with the simplest, and then choose something more difficult.

Look, what a funny pig turned out in the form of a wonderful flower pot, like a flower bed. Read the description right now.

And here is the end result. It remains only to cut a hole on top and place the seedlings there or leave it like that.

Also interesting idea from cans and bottles. This is such a person or a robot.

You will also need music CDs. In metal cans, make holes with an awl and thread the wire and connect one to the other.

Make the body from a large plastic bottle and also thread the wire to secure the arms and legs.

The eyes can be glued with a thermal gun, and the pupils will be beans.

I also suggest making a bird feeder, it is done quite easily and simply. There will definitely be no questions. Cut off the top of the bottle as shown here.

Then use a knife to make a fairly large hole.

Connect like this, you get a roof.

Make holes on the cork so that you can thread a thread or wire and hang it on a tree.

Color with acrylics for fun and to attract birds.

Also, if you wish, you can make a hunting trophy.

Probably the simplest is a craft in the form of a beehive with bees. Color any container in yellow paint.

On the lid, draw a muzzle, eyes and mouth with black varnish.

Glue the strips with black tape.

Well, already a real bee, zhu-zhu.

Only the wings are missing, draw them first on another vessel.

Then cut with scissors or a sharp utility knife.

It remains only to fix.

And such a bright flying charm will come out. Looks cool, doesn't it?

A cool bug, as my little one once called insects and bugs.

We make animals from plastic bottles

Probably many of you, when you got into this article, were looking for animals, because your dacha will certainly look great with them if you make them and seat them around the site.

Take this as a base step by step instructions with a diagram. I propose to execute waste material cockerel. Tape the three bottles together.

From multi-colored disposable cups, make an outfit for a rooster.

Of these, and feathers for the tail. But, it’s better to take disposable plates and cut off the edge from them, and then cut them. Use a glue gun or stapler to secure.

Now almost everything is ready, the head remains.

It can be made from any ball or ball, in this case, a ball for a children's pool is taken.

Draw or glue on eyes and a comb.

Now, as the animals promised, these are, for example, mischievous turtles.

Caterpillars, and they can be made from bottles and corks.

Cool options with horses and donkeys. Below, a master class will be shown, read on.

Cute pigs, one even winks at you.

Shown here are chicks and a sister fox from the fairy tale Gingerbread Man. Well, you can't do without a bear.

Look, a mischievous black cat, kittens and a poodle. And of course the brave peacock.

Frog princess, make sure if you have a pond. Bunnies and lamb.

And now, as promised, let's dwell on the donkey in more detail.

First, prepare the container for work, you will even need bottles of yogurt. Screw jar lids to the largest volume.

Then you need to make the head and neck.

This is the layout that should come out.

You can't do without ears either.

Straight really donkey came out, it looks like one to one.

Here is how the mane is done.

Remember to paint in the desired color, such as gray and white, use acrylic paints.

Then attach the box and why not another summer cottage masterpiece.

Here is such a scheme for cooking a peacock in my piggy bank, maybe it will come in handy for someone. More foam is needed.

By the way, have you thought about making a living zoo, for example, there will be giraffes and zebras in it.

And a boa constrictor or a snake will crawl nearby.

You can make a hedgehog from improvised means, taking more bumps.

Or a scary toy in the form of a shark, you can have some fun at the same time.

Without birds, the garden is also not fun, make a dove.

Or a magpie, for example, here already give free rein to your imagination.

Of course, the place of honor is occupied by swans.

No area is complete without them.

Because they are very beautiful, straight queens.

You can create a ladybug from plastic spoons or cut parts from a bottle and paint it in the desired color.

But the hero from the cartoon Crocodile Gena, only Cheburashka is missing.

These are the clumsy elephants that escaped from the zoo.

And this bird really struck me, an owl or an eagle owl, and instead of eyes, CDs. Well thought out.

Also, such a bird, which symbolizes the birth of a child, is a stork. Plant it in cabbage, it will be quite elegant. True, you will also need plywood, wire, polystyrene foam and milk cans.

Master class on how to make a palm tree with your own hands on the site (scheme)

A tropical plant, like a palm tree, has long won the hearts of the inhabitants of Russia, it is it that often fills the interior in the garden. See this diagram and follow the steps you need.

And if you have any questions, you can watch the video.

In any case, you will understand, there is nothing difficult in this. So hoard stuff.)

What can be done with plastic bottles

Now I want to invite you to see the most unusual ideas that I came across. There will only be new items. I want to show such a Christmas tree from a green Fanta bottle.

They even make brooms and shovels for cleaning the territory. Great idea.

Unforgettable look topiary, take a look.

Or from traffic jams decorate fences and gates.

And in the villages, houses have already begun to be cultivated. How many of them you need to accumulate, horror.

But they even came up with the idea of ​​using instead of a light bulb, the light and rays of the sun hit and illuminate the room in the attic.

Here is such a box for little things, or something else.

Take care of the birds, make them a feeder.

Or such an octopus will please your eye.

Girls and boys, nesting dolls and other little people.

And of course the flowers are lilies of the valley.

Or daisies, poppies, what do you like more?

And here are the lilies, how wonderful.

And someone can put a decorative teapot and a mug on the table.

We talked about butterflies above, and here is the dragonfly, but so huge.

Well, you can’t do without a washbasin, build one, especially since it’s great option if you go out of town for a picnic.

You can often find unique fences that can be made from bottles of dairy products.

Or decorate with strawberries, it looks just great.

These are some pretty flower stands.

Or a watering device, screw the bottle onto the hose and make holes in it, you will get a spray, like from a watering can.

Who would have thought even cacti can be built, and even with thorns.

Also very popular are the minions, as they are to you.

Interesting ideas, right?

Beautiful crafts from plastic bottles, caps and corks

I suggest immediately adopting these ideas from this video:

See you soon here. See you.

Sincerely, Ekaterina Mantsurova

Good day to all!

Summer is coming and along with preparing your summer cottage for the garden season, you need to take care of its design.

The use of old and unnecessary things has become not only popular, but also environmentally friendly. Used car tires, corks, plastic bottles - from all this you can create very interesting and unusual creations.

If you have accumulated a lot of plastic bottles, then why throw them away, let alone burn them (each burned bottle increases the amount of harmful carcinogens in the atmosphere). You can make a lot of interesting crafts out of them, which is what most gardeners do. In this article, we will see what can be done from this material.

Let's start with the simplest. If you do not need any figures on the site, then making flower beds will be just right.

Such a wonderful border can be made by digging inverted bottles into the ground. You can paint them, or you can leave them like that. You can make it even more interesting. If they are cut in half and dug not upside down, but down, but in free space pour land and plant some flower. Then you will get a border not only from bottles, but also from flowers.

If you insert the cut plastic container into each other, you get another version of the border that does not need to be dug in.

The next photo shows a two-tiered flower bed. If desired, you can make a few more tiers.

In general, there are a lot of options. The main thing is to show imagination.

From corks from plastic bottles, you can make a path on the garden plot.

If you decide to make interesting crafts, then the examples given here may help you realize your ideas.

A wonderful craft that uses and Additional materials in the form of old shoes and fittings.

And this photo shows original design sofas from plastic bottles.

If you want your garden to look like a house somewhere in the tropics, then you can "plant" such palm trees.

By the way, you can fence with plastic bottles not only flower beds, but also make beds.

Also, if there are a lot of bottles, then whole structures can be made from them, like this gazebo.

You can also make a fence of your site from bottles. For example, here is a fence.

We will decorate very interesting summer veranda at his dacha, having made both furniture and elements of room decor.

Well, if you have a river or some other body of water nearby, then such a boat will be a must.

The most traditional thing that can be made from plastic bottles, and that many safely do, is a bird feeder. Five-liter containers are well suited here.

If you are an amateur gardener and do alpine slides, then a Mexican-style slide decorated with cacti will suit your taste.

And, of course, flowers. This handmade product is created from almost any material. Paper flowers - origami, are most often made for holidays or any other events. Silk or satin flowers. Plastic also works well for this purpose.

These flowers can decorate household plot, and put in a room in a vase.

There are a lot of options for making such crafts - it all depends on the imagination and possibilities. Some of these options will be discussed below.

How to make flowers with your own hands (step by step instructions)

Plastic bottles can also be used to make decorative flowers. There are a lot of options for such crafts, here we will consider the most common ones.

In the first version, such a craft is done.

To make such a flower, take a bottle and cut off the top and bottom of it. As a result, we get three blanks.

Now we take upper part and we make cuts from the bottom - to the neck, so that we get flower petals and stamen filaments.

Their number may be different. Thin strips will be sepals, which must be bent to the sides and twisted with a knife or scissors.

In the same way, we bend and twist wide strips that will be petals. Only the stamens will remain at the top. As a result, we get the following construction.

To make the flower look more beautiful, you can paint it with nail polish. You choose the color which will look best.

From the bottom of the bottle in a similar way, you can build the same flower. There is no need to twist the cut out parts.

Another interesting and easy way making flowers. Here will be used colorful bottles, corks from them and wire for the stem.

From the bottle here we need the bottom. Carefully cut it off and cut out the petals.

A wire is threaded into the middle of the flower and secured from the outside with a loop.

A lid is glued in the center of the flower. The result is a flower, but still with a wire stem. The next step is to make the stem.

To do this, cut off a strip of about half a centimeter wide from a green bottle.

We wrap the stem with this strip. In order for the plastic strip to wrap well, it must be heated with a lighter.

From the same green bottle we cut out the leaves and attach them to the stem in the same way.

Thus, plastic flowers are ready.

This flower making is very simple. On the wire, which serves as the basis of the flower, we string the circles cut from the bottle.

They can be made in different colors. And decorate, then, even a flower bed in the garden.

If you use the bottom of the bottle, then you can make this kind of flower.

And, I want to give a photo scheme of another interesting product.

Everything is simple here too. We make a pattern of petals, according to which we cut a blank from a red bottle. Cut out the green leaves. We give red blanks by heating a different shape. The diagram also shows that small denticles can be cut along the edges with scissors. That is, make the flower terry.

After that, the finished flower petals are attached to the wire. She herself is wrapped in a strip of green color (as in the version above) and leaves are attached. As a result, we get a finished flower.

We make pots and vases for flowers in the country (a master class for beginners)

Since we talked about making artificial flowers earlier, how not to forget about real ones and not make a pot or vase for them. In it, however, you can put, however, an artificial flower made right there.

I want to start from the very simple option. Probably, few people would have guessed about it, it is so simple to manufacture. Here we only need a bottle and an unnecessary CD.

Cut off the top of the bottle. The size of this part depends on what will be planted in the pot. We leave a cork on the neck. Having smeared glue on it, we glue this part to the disk. The vase is almost ready. For "prettyness" we paint it either in one color, or paint it. By the way, lower part, left over from the "halving", can also be used under the pot.

In the next variant flower pot, united together the upper and lower halves.

If you cut off the lower part of the bottle, it stands well, and then glue a cork nose to it, make eyes, then you can get such a decorative pot.

Another very simple option for making a vase for flowers from a bottle. This option is well suited if you decide to decorate the wall with flowers such as petunias. To this end, we cut out the side wall of the bottle, make holes through which we pass the rope.

To keep the bottle, we make knots at the bottom on which it will hang. Having poured earth and planted our favorite flowers, we will get such beauty.

Similar pots can be made differently. We cut off the upper part, close it with a cork, paint it as it should. After that, we fill up the ground, plant the plant and hang it where necessary.

Check out this step by step video tutorial, you'll love it!

Here are such wonderful vases you can cook. If you have some idea of ​​your own, according to which you made a craft, then be sure to share it with readers in the comments at the bottom of the article. Maybe someone else would like to do something similar.

Beautiful zoo in the country from bottles

Many people are now striving to make beautiful sculptures on their site. This is due to the fact that the majority come to the dacha not only to stand in the garden all day, but also to take a break from the city. And if your cottage is beautifully decorated, then the rest will be good.

Most often, figurines are made in the form of animals. Making such crafts is quite easy, and the material is always at hand.

Looks good on the stone is such a frog princess.

You can make such an African composition.

Whatever your vegetable plantings looked attractive, put such a wonderful donkey among pumpkins or zucchini with eggplant.

Or such a cunning fox.

If you show imagination, you can even put penguins in your garden.

There is no need to talk about our traditional forest and cartoon animals, such as these bunnies. The kids will surely love them.

If you collect several bottles of different calibers, then you can settle a family of pigs somewhere under a bush.

Previously, it was said about a donkey craft, which, if placed among vegetables, you can decorate a garden bed with this craft. And if you attach a cart in the form of a vase of flowers to it, you get a street flower bed.

Good luck in making wonderful crafts and creative success!